A few months back my Legend went through a cycle in the washing machine. Afterwards I did all the recommended things (take everything apart, leave it in the sun for a day or two, keep it in a jar of water absorbent silica in the evening). Anyway, after three or four days of that, I put it back together again and my battery was dead. Tested it with someone else's battery, and everything worked perfectly, I even made a call with it.
I then waited about 3 months for a new battery (it got stuck at customs) which I finally go this week. Thing is, I now have 0 connectivity with the phone no matter what I do. I always have 0 bars, I can't connect to wireless networks (even though I pick them up perfectly), and I can't get the GPS to turn on at all. Everything else works fine (including the FM radio), but there's no connectivity.
I was hoping it might be a software issue of some strange sort, since the wireless picks up well but just says "connecting--disconnected" when I try to connect. A hard reset did nothing to the phone though.
Is there anything else for me to try? I'm running pretty thin on ideas at the moment. Would replacing the back cover fix any of the connectivity issues? Also, is it still possible for it to be a software problem, and should I maybe try to install a custom rom on it?
Any advice at the moment would be much appreciated. Thanks!
EDIT: I just realised that I had made things worse with my reset. Now I have no file browser with which to sideload apps and no internet connectivity. EDIT2: Managed to fix the file manager problem with ADB. Now just the actual problem again
The GSM antenna is in the bottom part that covers the battery compartment - I'd say you have some oxide on those two contacts.
Take a small screwdriver (or a needle) and gently scrub those pins on your phone.
As for the two on the cover, you'll notice those two parts come apart, so I'd take the inner part and gently brush the two contacts with a piece of cloth and a toothpaste - it's a good thing to gently brush something.
If that fails and you're sure you plugged all inside as it was...it could be another problem...
You may also try bending the two contact in the phone out - these act like a spring, but be gentle about it
P.S.: Is your Legend at least clean now?
EDIT: Now that I think about it, you can try the phone with piece of wire:
cut a wire of : speed of light/frequency in Hz and connect it to the two pins inside the phone
For USA:
299 792 458 m/s divided 1 900 000 000 Hz = 0,15778 m
Thanks Dr.Romca.
I'm trying the clearning out for now. when you say the battery cover comes apart, are you talking about the piece of plastic inside the rubber? There seems to be an additional piece of plastic inside the rubber which might come loose, but I'm not quite sure how to pry it out without breaking it. Any tips on how to do this?
I'll give the piece of wire a skip until the very end
It's not glued or anything, just push the rubber part in the middle and try to click it out...
Dr.Romca said:
It's not glued or anything, just push the rubber part in the middle and try to click it out...
Click to expand...
Click to collapse
Ahh ok, I wasn't sure what to expect on the other side. Didn't want to jam a screwdriver in between the plastic and rubber and hurt some electronic component. Managed to get it loose though, and gave it a thorough but gentle rub down.
EDIT: Nope, still no service on it. I still find it strange that it doesn't want to connect to the GPS or the wireless either. As far as I know, those shouldn't be affected by an antenna issue right?
That's strange... WiFi and GPS antenna is in the other rubber part....
It seems there might be something wrong with the PCB...
I'm at a loss here...
Damn I have connectivity issues here...
The strange thing is it worked once after the washing...
If you have the courage for it, you can also try this:
Take the phone apart, I mean really apart, if you can unmount the display/touchscreen. Then take the PCB - mainboard, try to put a sticker over a microphone and the repro, then take a toothbrust and a detergent and brush the PCB - make sure you clean all, there will probably be some metal plates that look they can be unmounted, so try to unmount them and clean beneath them.
After this take the PCB and put it in the hot-air oven (if you have one - NOT a Microwave! ) 40 - 50 °C for like an hour should do the trick...
You can also use alcohol to clean the PCB, but since it was water that caused this, I'm gonna presume you'll have more luck dissolving with water again...
Anyway, that's what I'd do, but I'm and engineer, so if you're not sure, just take the phone to service
Hello,
The WiFi and gsm signal are at seperate places on your phone, so you either got a major problem with the hardware, or the ROM just went nuts. I suggest you flash a new ROM before you take the phone apart, cause it might get damaged irriversably..
Goodluck, keep us updated!
Sent from my HTC Legend using XDA App
Thanks for the continuing advice. You're right about the engineer thing though; since I'm not an engineer I'll leave taking the phone apart until the very end.
I've never flashed a ROM before, but I'm sure I'll be able to figure that out. What initially made me think that the ROM might have gone crazy is the fact that the wireless actually picks up networks. The further I get from a network, the worse the signal, and the closer I get the better, so the wireless signal is working properly. It just seems to have a problem connecting, which seems like a software issue rather than a hardware issue.
If that fails, I'll send it to HTC and see if they can do a repair for me. I already sent it to them for a check-up and a new battery directly after I had it dried out. I included explicit instructions that it got water damaged, that I was not looking for a warranty repair, and I would just like them to make sure everything is working and bill me for the repairs and a battery. Two weeks later I get the phone back with a note saying that they noticed some water damage, and they don't do warranty repairs on water damaged phones Anyway, I'll try them again.
If HTC fail to do anything again, I'll try my luck with a full teardown. Still, ROM flash first.
EDIT: Ok, so I followed this (http://forum.xda-developers.com/showthread.php?t=894465) post up until the end of downgrading your rom, and the problems are exactly the same. From my understanding, this would have installed a clean rom onto the phone, so any software issues should have been cleared up. I'll still try and install a custom ROM, just because I've always wanted to and just maybe something will work, but the software problem seems an unlikely explanation now.
This is getting very strange now. Using my newfound "Wi-Fi" Hotspot powers, I can actually create a Wi-Fi hotspot that my computer successfully connects to. Once again, if the hardware was broken I don't see how this could work. I still can't connect from my phone to any Wi-Fi network though.
As I mention (for a completely unrelated reason) earlier, I sent the phone in to HTC. This might be a very dumb question, but is it at all possible that the ROM on my phone works at a different wavelength/frequency than what is used by carriers in South Africa (where I'm from)? I'm thinking maybe HTC did a stock reset or something which changed it, because I never tested my phone after getting it back from them. That would also explain why my phone doesn't have reception with the current ROM. Just note that I have no idea how these things work, it's a complete shot in the dark
EDIT: My GPS also works now, or at least the gps indicator flashes when it should. Since I don't have any kind of internet access, I have no way of knowing if the GPS works, but in the past it never flashed.
I'm currently thinking of using my computer's wireless to connect to my phone, and then bridging that connection with my UTP connection to connect to the internet. I have no idea if this will work or what exactly if it will get me closer to a real solution, but at least having internet access on my phone will make things a bit easier. Will let you know how it goes.
So have you succesfully flashed a different ROM?I'm not sure what type of rom should you have but WWE by it's definition should work...So if you have rooted, try any WWE ROM...
Dr.Romca said:
So have you succesfully flashed a different ROM?I'm not sure what type of rom should you have but WWE by it's definition should work...So if you have rooted, try any WWE ROM...
Click to expand...
Click to collapse
I first downgraded it to 1.31, and now it's on BlaYo's B0.2.
can you check what radio you are using?
You may want to update it!
It's in settings / about phone / software / baseband version
My is 47.51.32.17U7.13.35.05
Not sure if there's a special version for SA, but here is a radio update only:
http://forum.xda-developers.com/showthread.php?t=706435
Sorry for the late reply. Real life caught up for a day or two.
My baseband version was 47.26.35.04u_7.05.35.26L. I updated it with the radio update you posted, and it's still not working. As far as I know, South Africa can use any American phone except those on Sprint, if that helps at all.
Also, I was away from home for the last week, and now that I'm back home my phone connects perfectly to the wi-fi here. I am certain that I did not make any mistake in connecting to the other networks I tried, as I tested the settings on multiple computers and entered the passwords multiple times, but the wi-fi seems to have been a red herring. So the only problem left now is normal phone connectivity.
I'm sorry to hear that...I'm not sure what the L means at the end...but about the wifi thing, it has been mentioned here that different locations use different WiFi channels...so at this point it's almost sure you have a driver/settings mismatch somewhere...
but I don't know much about that...sorry..
Related
Hi, I hope someone can help me.
I dropped my phone a couple of months ago and now I'm experiencing a problem. It appears to work fine for hours then suddenly starts losing signal strength to the point where it goes altogether. I can start a call with 5 bars and be cut off with no signal in a minute even though I've not moved. It will nearly always lose the signal when I'm on the phone but takes longer when just in other use. All remaining elements of the phone work fine. Please can someone suggest what it could be as it is getting me down...thanks
I'm sure it's a hardware problem.
have got the same problem.Did you already find the problem.In the beginning the signal just dropped but know i even cannot find any service at all.
gr
I've had some luck by raising all the contacts under the sim card but the signal still comes and goes when I use the phone ??
Snap!
I droppped my phone the other day and it is doing exactly the same thing. Mine is a Qtek S110. I used to 'lurk' on this forum ages ago.. but [email protected] BACK to seek help! If and when I get my phone fixed I WILL post and let you know what it is, if I havent already found the solution here!
I think it definately has something to do with the SIM holder, whenever the signal decays and vanishes, if I take out the sim and put it back in it comes back straight away. if I just take out the battery and replace it doesn't
ok.. next time i lose signal I will do that. maybe even run some isopropyl alcohol over the contacts to make sure they are clean.
I will keep you posted in my findings!
(oh.. i tried a makeshift external aerial last night to see if I could see if it was an internal aerial fault. It didnt make any difference, so either my homemade job was [email protected] or it isnt an aerial problem, I'm yet to find out!!)
Cheers!
oh poooop..
that unfortunately didnt work for me.. Oh well. i even tried cleaning the contacts and making sure the 'sprung' contacts were connecting with the Sim correctly.
I actually lost signal until it came back 15 mins later.. hmmmmmmm!!!
Can anyone advise where I can look on the circuit board to see if there is any damage. I am capable of doing this and making a basic repair !!
I had a look at the mda strip down guide on here, but I could see any reference to the aerial or anything. I think I'll have to send off for repair! Doh!
I emailed HPC and they wouldn't take mine back as apparently it was not sold in the UK.
I think I'll give xdarepairs.co.uk a go. a mate of mine said they were good n' quick.
merceeeeeeeeeeeeeeeeeeeeeeeee
no wurries!
the unit that sorunded in red (in the Attached picture) is connected to the main board with tiny connector, and this connector is a male to female connector. the male is solderd to the main board and the female to the unit. my guess is that one of the connector parts (the male or the female) was disconnect from its soldering, and you need to resold it. but it is just my guess based on my experience.
I was taking a look at the mda-jam.pdf guide to removing the case and it suggests that the aerial contact on the board you have pictured is with the front panel.
Can anyone confirm if indeed, the aerial for the phone is the metal casing? That would suggest that the dents in the front of mine could have affected that very contact.
Would still like an answer to my previous post.. but I think I may have fixed my phone temporarily.
Using the above information I got a flat bladed blunt instrument (in this case a normal dinner knife) and carefully placed it into the empty sd card slot. Using the diagram from the case removal guide I applied pressure with the knife to the area where the 'aerial connector' rests against the front bezel, inside, whilst at the same time pushing on the front outer casing with my thumb in the same position.
The thought process being, that it may have worked loose.
Sure enough I have noticed a vast improvement in signal yesterday and today. I am going to keep an eye on the phone today when I go out to see if the signal stays up!
YAY!
Okay.. latest update.
The signal did drop out a little bit throughout the day, So I have taken it upon my self to put my electronic training to good use.
Using the (now much read) case removal manual I carefully .. and I MEAN carefully took my phone to pieces.
I was convinced that the reason my signal kept dropping out was either that something had worked loose or that there were some contacts that needed cleaning or reseating.. as I was able to get a signal by squeezing the case at the top.
So.. Here's what I did (In reverse order)
Page 9 straightened and cleaned the 3 contacts on the RHS plastic plate with isopropyl alcohol. Also cleaned the corresponding contact points on the main PCB with alcohol and dried with a lintless bud.
Page 10 3 contact points, top right and top edge left are the contact points I refer to above. Also cleaned the 2 sprung contacts at the bottom of the PCB RHS page 10
Page 16 cleaned sprung 'Aerial Output' contact with alcohol.. also pushed connector outwards to make a betterr contact. Also cleaned 'contact to the antenna' area and dried thorughly with a lintless bud. Any other contacts I could see were cleaned and dried too.
Whilst putting the phone back together I was very careful not to touch any components. Battery contacts and Sim contacts were also cleaned.
One thing to note in the manula is that it it possible to unclip the connector for the camera prior to removing the plate in page 8. However, it is probably best to follow the guide, if you are unfamiliar with the type of connectors used. They can break easily.
My phone booted correctly and is currently on charge.. I am checking functionality at this very moment and can see that the signal is good and all other parts / hardware functions appear to be good. watch this space! It COULD be one fixed phone!!
I can't remember who on this forum wrote the mda-jam.pdf manual, but I would like to publicly thank you as you have helped fix my phone!
I hope its worked !!! Let me know !
OK!
Well so far I have noticed a dramatic improvement on how the phone was. I am sitting here with full signal, whereas on Saturday I had between 2-3 bars.
I lost a little signal earlier today but as soon as I held the phone up, the siganl came back. So, it's not perfect, but the phone is useable now.
As long as it lasts for the rest of my contract, I'll be happy!!
Dood.
Hello;
It's been like a month that I have this problem, my bluetooth won't connect and neither is my wifi. The wifi sometimes connect with like one bar, the signal strength is awful and you have to be like 1 feet away of the router because if you move farther it disappears. I have tried to boost this in the settings by better performance but it doesn't make a difference.
In the other hand the bluetooth is not working at all, I tried to connect to my laptop and is like there's no bluetooth device in the area, tried it with my headset and get the same thing.
It's really frustrating cause this two features are very important for my daily use of this phone, so if someone now what to do please let me now.
Appreciate it!
Same here!
I have the exact same problem and apparently by the lack of posts anywhere on the internet nobody has an answer.
im having EXACTLY the same issue. im gonna open it up and see whats up.
The answer might lie within?
Try this link? What you're looking for might be somewhere in amongst these threads? http://forum.xda-developers.com/search.php?searchid=48353718&pp=25:confused:
can you repost that link? its saying search is down..
edit: working now.
???
I get a "Sorry - no matches. Please try some different terms." message.
???
nothing worth noting on the link. im gonna send mine back to htc..
I'm hoping someone will get to the bottom of this as i miss my wifi.
All was working fine on my phone until I had to take my phone apart because the plastic led shield had come lose and was touching the vibration device causing a strange noise.
So i managed to get the phone apart and push the led plastic cover back into place, i didn't touch anything else. I put the phone back together and all worked fine until i tried the wifi. Nothing, it turns on but stays as scanning and never finds anything even if its right next to the router.
I was advised in another thread that one of the cables might have come loose as i took the phone apart so i opened it up again but couldnt see anything wrong.
I'm just wondering if its a software issue somehow. As i never touched any part of the board, or antenna etc whilst it was apart and like i've said i couldnt see anything out of place or loose. Whether a hard reset will solve the issue i dont know and its a pain to do really.
I haven't tried bluetooth, but considering it looks to work off the same antenna that too might have broken.
maybe solved
find bttrayce.exe or bttrayce.lnk in windows folder
run it and check them
copy lnk file to startup folder
restart
this is for wi-fi too .
I've run bttrayce.exe and the ink file is in the start up folder.
This hasn't made any differance.
enable wifi n mode using registry editor like total commander or resco, go to:
HKLM/Comm/BCMSDDHD1/Parms/11nModeDisable = Change from 1 to 0
or, install bsb tweaks and enable wifi n mode.....
or, the best answer is to flash a new radio-improves bluetooth, data, wifi and call signal
malanga3 said:
Hello;
It's been like a month that I have this problem, my bluetooth won't connect and neither is my wifi. The wifi sometimes connect with like one bar, the signal strength is awful and you have to be like 1 feet away of the router because if you move farther it disappears. I have tried to boost this in the settings by better performance but it doesn't make a difference.
In the other hand the bluetooth is not working at all, I tried to connect to my laptop and is like there's no bluetooth device in the area, tried it with my headset and get the same thing.
It's really frustrating cause this two features are very important for my daily use of this phone, so if someone now what to do please let me now.
Appreciate it!
Click to expand...
Click to collapse
did you hard reset and the problem persists? then it is a hardware issue, send it to htc.
Hopper81 said:
I'm hoping someone will get to the bottom of this as i miss my wifi.
All was working fine on my phone until I had to take my phone apart because the plastic led shield had come lose and was touching the vibration device causing a strange noise.
So i managed to get the phone apart and push the led plastic cover back into place, i didn't touch anything else. I put the phone back together and all worked fine until i tried the wifi. Nothing, it turns on but stays as scanning and never finds anything even if its right next to the router.
I was advised in another thread that one of the cables might have come loose as i took the phone apart so i opened it up again but couldnt see anything wrong.
I'm just wondering if its a software issue somehow. As i never touched any part of the board, or antenna etc whilst it was apart and like i've said i couldnt see anything out of place or loose. Whether a hard reset will solve the issue i dont know and its a pain to do really.
I haven't tried bluetooth, but considering it looks to work off the same antenna that too might have broken.
Click to expand...
Click to collapse
so wait, you take the phone apart, put it back together, then it doesn't work, yet it isn't your fault? I hope you didn't screw up the void sticker covering the one screw when you did this, because you obviously damaged the the wifi cable in some way.
Obviously i'm aware that what ever has happened is my fault, my point was that if i'd taken it apart and knew i'd done something that might have damaged the board etc then that's fine I would be able to pinpoint what it was, but as i didnt do anything really especially to the main phone just the back case it's just a little odd.
Void sticker is fine.
seems like an antenna problem, there is a cable on the side of the phone with the volume rockers, there will be a cable going to the top board to the bottom board this cable attaches and can be removed. try to remove then reattach the cable
http://www.youtube.com/watch?v=cL-jnUKufC4&feature=player_embedded
the cable is on 2:38 of this video.
Right I took my phone apart again this morning to double check everything. I noticed the cable attached at the bottom as mentioned in previous post. It lifted off a bit too easily, so I positioned it correctly and pushed it back down, my WiFi now works. So that was my issue.
So my advice would be if both your Bluetooth and WiFi do not work, it is more than likely the cable is lose. (more likely if your phone has been a part obviously)
Thanks for everyone's help and advice on here.
I had the same problem with my GPS. I took the phone apart and found that the GPS unit was connected to an amplifer via two gold prongs. The connection was not flush, so I stretched the prongs abit (not too much) to improve the connection and put the phone back together. The problem was now fixed.
From memory I think the bluetooth and wifi worked on the same principle, and I think the amplifier states what its function is.
Hope this maybe some help.
First the problem.
Like many others HTC HD owners and I encountered this problem 2 days ago (i have nolonger waranty). i just was connected to my computer thru USB for couple hours, when i tried to power it on, the phone display dont comed on, but the phone worked fine (i maked couple conversations. After that i started to read about this problem, a lot of problems, but no solutions.
I try everthing - put in refrigerator (it worked until i turn off the display, pulled the battery for the night, and one bucket with operations without effect.
i install mymobiler and i was sure that my HD is working without display, then i disassemble the phone and checked the connectors, but no effect either.
i am radiocommunication and electronic engineer, and i don't give up so easily
i pulled the main board, and blowed the main board with hot air flow solder machine (i blowed exactly all over the shielding, from the bottom side not SIM card side), i wait for cooling then asemble the phone, and voala "Its alive"
NOW I AM IN TESTING PERIOD. I WILL WRITE WHEN I AM SURE THATS WORK FOR ME.
i have no pictures but i will make when i disassemle the phone again, because now is not fully asembled.
cheers!!!!!
p.s. i am sorry for my bad english
p.s. i am so happy trallllalalalalalal
It's not uncommon to see bad phone soldering on HTCs phones. Guess their factory isn't working right. Good job btw.
72 hours later everything looks great, the screen works perfektly, touch too, wireless communication too. i will post after few test again.
p.s. its look like my battery now have better handling....
6 un grande!
Wow!!! It's a good new. I had the same problem and I will try your solution. I hope it works on my phone.
Cheers!
I have problem from another type:
The problem is with signal. It was perfect until one day, the 3G has gone & then start losing the signal some times 3G return poor or strong, I take it to the HTC service center in Saudi Arabiya & the told me you have to change the main board then they do it but the same problem still there.
Now still have the problem even after change the main board, is there anything if have to change it or do it???
Note: it files down from me before this problem happened.
HTC Touch HD T8282
WMPro 6.1
Build 20757.1.4.0
Rom 1.14.415 ( 32434) WWE
Radio 1.10.25.25
Protocol 52.57.25.30U
ExtPkg 1.14.415.2
dr_crx said:
I have problem from another type:
The problem is with signal. It was perfect until one day, the 3G has gone & then start losing the signal some times 3G return poor or strong, I take it to the HTC service center in Saudi Arabiya & the told me you have to change the main board then they do it but the same problem still there.
Now still have the problem even after change the main board, is there anything if have to change it or do it???
Note: it files down from me before this problem happened.
HTC Touch HD T8282
WMPro 6.1
Build 20757.1.4.0
Rom 1.14.415 ( 32434) WWE
Radio 1.10.25.25
Protocol 52.57.25.30U
ExtPkg 1.14.415.2
Click to expand...
Click to collapse
did you try to change the radio???
This could be caused by bad SIM card. Did you try another SIM? In my country it's not unussual for SIM cards to start malfunction out of the blue. Also, check contacts for grease or dust.
limberjack said:
i blowed the main board with hot air flow solder machine
Click to expand...
Click to collapse
Hi, ssory for a stupid question, but what is "solder machine" with hot air flow? Is it idustrial fan? If yes, it can give to great temperature and can damage motherboard.
Was your idea to solder again all solder connections and roads?
andrew-o said:
Hi, ssory for a stupid question, but what is "solder machine" with hot air flow? Is it idustrial fan? If yes, it can give to great temperature and can damage motherboard.
Was your idea to solder again all solder connections and roads?
Click to expand...
Click to collapse
the solder machine keep one temps at all around 280 degrees celsioum, i thunk the chips can be demaged with temture about 340 degrees, ofcourse it depends of how long time you will blow over the pcb. i don't resolder all tracks and elements (i have no such technology in my laboratory), i just blowed the shielded part of the mainboard, because i know that i can blow some smd element and they are very tiny.
p.s. i use this JBC AM6850 solder mahine
p.s.2 yes it was my idea - it is better than to do nothing with this PDA and throw it in the cupboard
The solution still work for me...
bueno suerte...
limberjack said:
First the problem.
Like many others HTC HD owners and I encountered this problem 2 days ago (i have nolonger waranty). i just was connected to my computer thru USB for couple hours, when i tried to power it on, the phone display dont comed on, but the phone worked fine (i maked couple conversations. After that i started to read about this problem, a lot of problems, but no solutions.
I try everthing - put in refrigerator (it worked until i turn off the display, pulled the battery for the night, and one bucket with operations without effect.
i install mymobiler and i was sure that my HD is working without display, then i disassemble the phone and checked the connectors, but no effect either.
i am radiocommunication and electronic engineer, and i don't give up so easily
i pulled the main board, and blowed the main board with hot air flow solder machine (i blowed exactly all over the shielding, from the bottom side not SIM card side), i wait for cooling then asemble the phone, and voala "Its alive"
NOW I AM IN TESTING PERIOD. I WILL WRITE WHEN I AM SURE THATS WORK FOR ME.
i have no pictures but i will make when i disassemle the phone again, because now is not fully asembled.
cheers!!!!!
p.s. i am sorry for my bad english
p.s. i am so happy trallllalalalalalal
Click to expand...
Click to collapse
Dear
Yesterday i dropped my phone (exactly face down)- now the LCD screen show only (right side about 1 inch) bright light and remaining parts are blank. but it works fine - as when i get calls it vibrates. Pls guide me.
Hello Guys,
I just got my HD2 from repare, had to change the screen since it became unresponsive.
After I got it back, installed both WP7 and Anrdoid on it, I found out that the phone is not detecting any wifi networks. I tried in both WP7 and Android, and both of them do not detect any wifi networks. So it looks like when they changed the screen, they messed up WIFI connectivity. I'm guessing they might have forgotten to connect one of the connectors.
I am planning to take it back to them, but I was wondering if any of you knows which connector is for the WIFI, and if its easily visible once I take the back cover off, since I already done that before.
Thanks in advance
Hi dude,
if a connection is a problem and you even going to find it don't do it yourself.
it's a pretty small and gentle stuff, so you must know what you doing and how to connect them. Obviously you will need some serious tools.
my guess if you had all that - you already been doing this and not asking here.
so advice - not touching anything, not making it worse.
Best case: the connector came loose (which is not all that uncommon). It's the connector on the black wire on the top right side of the main board.
Worst case, they broke off a contact (which is also quite common).
Either way, don't try to repair it yourself but bring it back to the repair shop. If they accidentally broke off a contact then that requires a professional repair.
Thanks guys.
After some tests, I found out that the phone does detect wifi networks, but have extremely bad reception. I have to be very close to the wifi router for it to detect the network.
Any idea what might be causing this?
wessamzeidan said:
Thanks guys.
Any idea what might be causing this?
Click to expand...
Click to collapse
Like I said, either a loose connector or a contact has broken off. That will give you about 1 bar of reception while sitting next to your router...
I just recently replaced a malfunctioning LCD and shattered digitizer for my Glacier. Before I did that, the WIFI worked just fine. No problems at all. But now, the WIFI will turn on, but won't pick up any networks at all. All my other phones pick it up just fine, as well as my laptop. I've tried three different ROMs and I have the same issue with all of them. As far as I know, there weren't any cables that connected the WIFI module to the motherboard or anything else when I took it apart and put it back together. It's just a little piece that snaps into place, right? I'm not sure what's going on with this...
Seriously? Nothing? Every time I post on here, I get ZERO response... What gives? I see everyone else's problems being solved but not mine...
Sorry, there's no help to give. Don't act like you're entitled to something. I hate people like that. If you didn't touch the WiFi module through the screen and tried different roms then it went bonkers and its toast. TF are we supposed to do about that
Sent from my HTC Glacier using xda app-developers app
If you're gonna post on here just to be a douche, you might as well not post at all. It's doing nobody any good.
All drama aside, he is right nothing to be done really. I guess you could open it back up again and risk breaking something more important than the wifi. Something may be put back in wrong or may have got ESD damange. Truth is unless you're just using this phone as a toy/dev/learning device and don't care if it breaks it is not worth the risk to open it back up.
Trying to fix my external speaker - I mess up working wi-fi. In addition, the case crack and camera button is not working. Should take it to repair shop. Too late now. It would be too expensive to fix it. You my still be lucky and shop will fix for few bucks. Lesson learn - do not mess with something that you do not understand( for me).
coax cable issue
there's 3 little coax cables - I've been told the white coax is the wifi but the black one fixed it so maybe they are all involved. In the process of getting to the LCD you went through these 3 cables. In most cases you wouldn't have disconnected them but certainly by accident it will happen. I put mine on 3 times before they stayed. There's quite positive click when connected but even then it may come loose while assembling the rest of the phone. I just finished swapping out my mother board and as perfectly as I could reassemble the phone I apparently lost one of the coax connections = no wifi. Went back in and this time the black cable somehow got caught under the camera board instead of on top and connected. Easy to see why this was missed because it looked connected.. well looked like it belonged where it was (wrong)
Anyway that's my wifi fix story - hope it helps someone