S100 Loses Signal - JAM, MDA Compact, S100 General

Hi, I hope someone can help me.
I dropped my phone a couple of months ago and now I'm experiencing a problem. It appears to work fine for hours then suddenly starts losing signal strength to the point where it goes altogether. I can start a call with 5 bars and be cut off with no signal in a minute even though I've not moved. It will nearly always lose the signal when I'm on the phone but takes longer when just in other use. All remaining elements of the phone work fine. Please can someone suggest what it could be as it is getting me down...thanks

I'm sure it's a hardware problem.

have got the same problem.Did you already find the problem.In the beginning the signal just dropped but know i even cannot find any service at all.
gr

I've had some luck by raising all the contacts under the sim card but the signal still comes and goes when I use the phone ??

Snap!
I droppped my phone the other day and it is doing exactly the same thing. Mine is a Qtek S110. I used to 'lurk' on this forum ages ago.. but [email protected] BACK to seek help! If and when I get my phone fixed I WILL post and let you know what it is, if I havent already found the solution here!

I think it definately has something to do with the SIM holder, whenever the signal decays and vanishes, if I take out the sim and put it back in it comes back straight away. if I just take out the battery and replace it doesn't

ok.. next time i lose signal I will do that. maybe even run some isopropyl alcohol over the contacts to make sure they are clean.
I will keep you posted in my findings!
(oh.. i tried a makeshift external aerial last night to see if I could see if it was an internal aerial fault. It didnt make any difference, so either my homemade job was [email protected] or it isnt an aerial problem, I'm yet to find out!!)
Cheers!

oh poooop..
that unfortunately didnt work for me.. Oh well. i even tried cleaning the contacts and making sure the 'sprung' contacts were connecting with the Sim correctly.
I actually lost signal until it came back 15 mins later.. hmmmmmmm!!!

Can anyone advise where I can look on the circuit board to see if there is any damage. I am capable of doing this and making a basic repair !!

I had a look at the mda strip down guide on here, but I could see any reference to the aerial or anything. I think I'll have to send off for repair! Doh!

I emailed HPC and they wouldn't take mine back as apparently it was not sold in the UK.

I think I'll give xdarepairs.co.uk a go. a mate of mine said they were good n' quick.

merceeeeeeeeeeeeeeeeeeeeeeeee

no wurries!

the unit that sorunded in red (in the Attached picture) is connected to the main board with tiny connector, and this connector is a male to female connector. the male is solderd to the main board and the female to the unit. my guess is that one of the connector parts (the male or the female) was disconnect from its soldering, and you need to resold it. but it is just my guess based on my experience.

I was taking a look at the mda-jam.pdf guide to removing the case and it suggests that the aerial contact on the board you have pictured is with the front panel.
Can anyone confirm if indeed, the aerial for the phone is the metal casing? That would suggest that the dents in the front of mine could have affected that very contact.

Would still like an answer to my previous post.. but I think I may have fixed my phone temporarily.
Using the above information I got a flat bladed blunt instrument (in this case a normal dinner knife) and carefully placed it into the empty sd card slot. Using the diagram from the case removal guide I applied pressure with the knife to the area where the 'aerial connector' rests against the front bezel, inside, whilst at the same time pushing on the front outer casing with my thumb in the same position.
The thought process being, that it may have worked loose.
Sure enough I have noticed a vast improvement in signal yesterday and today. I am going to keep an eye on the phone today when I go out to see if the signal stays up!
YAY!

Okay.. latest update.
The signal did drop out a little bit throughout the day, So I have taken it upon my self to put my electronic training to good use.
Using the (now much read) case removal manual I carefully .. and I MEAN carefully took my phone to pieces.
I was convinced that the reason my signal kept dropping out was either that something had worked loose or that there were some contacts that needed cleaning or reseating.. as I was able to get a signal by squeezing the case at the top.
So.. Here's what I did (In reverse order)
Page 9 straightened and cleaned the 3 contacts on the RHS plastic plate with isopropyl alcohol. Also cleaned the corresponding contact points on the main PCB with alcohol and dried with a lintless bud.
Page 10 3 contact points, top right and top edge left are the contact points I refer to above. Also cleaned the 2 sprung contacts at the bottom of the PCB RHS page 10
Page 16 cleaned sprung 'Aerial Output' contact with alcohol.. also pushed connector outwards to make a betterr contact. Also cleaned 'contact to the antenna' area and dried thorughly with a lintless bud. Any other contacts I could see were cleaned and dried too.
Whilst putting the phone back together I was very careful not to touch any components. Battery contacts and Sim contacts were also cleaned.
One thing to note in the manula is that it it possible to unclip the connector for the camera prior to removing the plate in page 8. However, it is probably best to follow the guide, if you are unfamiliar with the type of connectors used. They can break easily.
My phone booted correctly and is currently on charge.. I am checking functionality at this very moment and can see that the signal is good and all other parts / hardware functions appear to be good. watch this space! It COULD be one fixed phone!!
I can't remember who on this forum wrote the mda-jam.pdf manual, but I would like to publicly thank you as you have helped fix my phone!

I hope its worked !!! Let me know !

OK!
Well so far I have noticed a dramatic improvement on how the phone was. I am sitting here with full signal, whereas on Saturday I had between 2-3 bars.
I lost a little signal earlier today but as soon as I held the phone up, the siganl came back. So, it's not perfect, but the phone is useable now.
As long as it lasts for the rest of my contract, I'll be happy!!
Dood.

Related

Wizard Repair Guide?! Mines Broken :(

Hey Guys,
Well, I'm a bit gutted really! I dropped my XDA Mini S on the floor with the charger in and the connector IN the phone has come apart from inside the phone. The little metal bit is practically hanging out. I'm wondering, if i were to take the phone apart could i re-connect the little part? (I have a soldering iron if thats as simple as its going to be?)
Just wondering if anyone had any guides on how to take the phone apart and take a look at whats wrong?
Any help would be so much appreciated!
Many Thanks,
Tom
The service manual is hosted on the ftp site.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/
Hope this helps.
I suspect you probably broke the socket off, but if you have a soldering iron, you might as well try to get a new mini USB connector to work with.
You might try Pocket PC Techs:
http://www.pocketpctechs.com/main~unit~UTStarcom_XV6700-554~area~repairs~item~REP-USBCON01~name~UTStarcom+XV6700+Mini+USB+Connector+Replacement+Service.htm
I rang them up about an issue I had (screen on the fritz) and they seemed pretty knowledgeable and helpful.
Alternatively there's a company I found today in the UK. I can't vouch if they're good or not.
http://www.xdarepairs.co.uk/home.asp
Good luck.
Well I also have an issue with my wizzard... the mini jack connector (of the handsfree) is a bit loose.
What I am saying is that it does have a good connection with the rest of the circuit and sometimes the sound of the speaker goes off, then I have to insert the habdsfree and tickle it a little bit until it has a good contact.
? have some basic soldering experience,do you think I should give it a try?
Given my device has been apart too many times for me to admit to I thought I'd crack it open to take a pic for you guys. Not sure if this pic will help for those wanting to do some soldering:
Very large pic: http://farm1.static.flickr.com/216/452691530_f47801708f_o.jpg
Excuse the dust.
Ah! That picture at the bottom is exactly what I needed. The metal but at the bottom (the big sqaure) has totally sheared off....bloody thing. Thanks so much for the info on the repair guides. I may give those repair guys a call if i can't get it to work myself.
Thanks alot you guys
As for you WizeMan, it all depends on if you wish to void your warrenty or not. At the end of the day, I installed WM6 on my device so O2 would give me the finger if i tryed to claim. If I'm honest, I'm getting an upgrade next month so I'm not to bothered if I balls it up! Would be nice if I got it working though....
Lemmie know how you get on
unlock k-jam
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
lironasseo said:
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
Click to expand...
Click to collapse
A little bit of a thread hijack but that means it is SIM unlocked.
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
WizeMan said:
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
Click to expand...
Click to collapse
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
AsGF2MX said:
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
Click to expand...
Click to collapse
Allright here is the deal.
1. I found out the break in the soldier joints when i opened it. I was really suspicious about it because when i inserted my headphone jack into the connector, i had problem with the contact; the connector was loose and it muted my phones speaker. When i disassembled the phone using the service manual i saw with my eyes that the the joins where f-ed up.
2. I dont really need the signal hack i just wanted to experiment, i have 2.25.11 cingular radio rom and its great.
Btw i suppose you should better use the sponge, because the rubber may wear off but not the sponge...
Thanks for the tip on the sponge. I am going to grab a used but allegedly "like new" body from eBay and also get one of those covers as well.

not able to get any service? help!

Ok, so today i woke up, and my phone no longer got service. I dont know what caused it. I dropped my phone last night and do not remember if I made a call after or not... But it was working last night. Would flashing a new radio fix my issue do you think? any insight would be good.
As you've dropped it, I'd open it up firt and see if the antenna is still attached (no cracks in connectors) properly.
I wouldn't flash a new radio rom as the radio is the achilles heel of the Hermes. It could become permanently bricked. Thats ALWAYS the last resort.
So, I do not at the time have a small enough screwdriver to get into my phone, because I am at school, but when I get one, where is the antenna located and what should I look for, I looked through the pictures on the wiki but none of them seem to show where the antenna is, please enlighten
You need a size 6 torque key, NOT a screwdriver or you'll kill the top of the screws.
The antenna is the large black plastic part at the top of the Hermes. Its directly under the back plate and pretty much takes up the whole top of the phone. There is a torque screw holding it and the flywheel circuit board onto the rest of the Hermes and he antenna has a copper coloured clip on the side next to the power button. See if its still connected or if the clip is cracked/damaged in any way.
Cheers...
i opened her up, saw no connection issue or any sign of damage what could my problem be, and yes, i did pay the bill

replacing G1 speaker

Hey guys,
The earpiece speaker on my G1 has developed a fault, the fault being it doesn't appear to work, how easy is it to source a replacement for it and how easy is the repair itself? is there any guides as to how to do it around? (i looked but i couldn't find anything).
I've tried flashing the rom and doing a hard reset but its still faulty.
The loud speakers working fine though so atm all my calls have to be done on the handsfree kit or via loudspeaker which can get annoying.
any help is much appreciated
regards
Streather
Are you using a ROM where sound works?
What ROM are you using?
Tried it with cynagen and the stock tmob one, same results.
Same problem
I'm using CyanogenMod 4.2.5. I dropped the phone about a foot (it fell out of my shirt pocket as I was tying my shoe!), and the earpiece stopped working. Everything else (speaker phone, etc.) works fine.
I've seen a number of similar cases in other forums, so I'm thinking that this is a weak point. I'll attempt disassembly and see if the speaker contacts got moved or something simple. Fortunately, replacement receivers/earpiece/speakers are available over the net.
Meanwhile, I'd love to learn of others' experience with this. The tech manual makes it look like you have to just about completely disassemble the phone to get at the earpiece, even though you can easily access 3 screws on the back of the lcd. Is there a shorter route to the receiver than a complete disassembly?
[update] I found some good info (including a technical manual) by Googling "g1 phone disassembly". And searching for "g1 speaker" on eBay gave some decent looking results.
[update 2] I disassembled my phone, took out the receiver, cleaned its contacts, replaced it, and and reassembled everything. That was a pretty serious chore, and it demonstrated that a nearly complete disassembly is required to access the receiver (yes, including all the stuff at the opposite end of the phone). I don't know how to test the receiver without being in cell range, which my house is not. But at least nearly everything else still works, except the camera--I need to tear back into the phone and make sure I fully seated the FPC. I think finding a replacement receiver will be a challenge--most of what turned up on eBay is actually the main speaker on the back of the phone, and I have yet to find a vendor that sells receivers.
Sadly, you will almost have to tear down the whole unit to get to it. It's not extremly diffucult, but you will need to be steady and gentle. Good luck.
Success!
I haven't seen many report back after tearing apart their phones to address issues with a bad receiver, so here goes. My simple-minded approach of opening it up, cleaning the receiver contacts with a pencil eraser, and ensuring good alignment before reassembling WORKED. I did not have to buy a new receiver.
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
I dropped my phone once, by accident, same thing happened. The speaker you use to put your ear up to when making a phone call doesn't work, but the speaker phone speaker works as does a bluetooth headset. Called HTC lied said that it just stopped working out of no where, they said its covered under warranty. Luckily the phone is under warranty until March and will be replaced.
I ran into the same problem. I was having intermittent problems with the earpiece. Yesterday I was able to take out the battery and put it in and it started working again. Today that didn't help either. I saw this thread and I thought that I'd try blowing really hard on the earpiece to see if that helps. It seems to be working again! I hope it continues to work.
dirtprof said:
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
Click to expand...
Click to collapse
Can you post details on how to do this?
My camera stopped working too.
I personally found it easier when disassembling the phone to carefully lift the entire camera and IMEI sticker as a whole unit and remove it as part of the motherboard. That way you dont need to mess with that hard to reach connector. So from where you are at, lift the board back out, reattach the camera assembly, and reassemble as a unit. I think you will find it is MUCH easier
Seat the camera FPC fully
RueTheDay said:
Can you post details on how to do this?
My camera stopped working too.
Click to expand...
Click to collapse
I had to lift the motherboard up and away from the hook that held it down in order for the FPC clip to open fully. Then I inserted the FPC *fully* before closing the FPC clip (my failures resulted from not being able to fully seat the FPC because the FPC clip could not fully open as long as the motherboard was in place). Then the trick was to get the motherboard back under its hook without accidentally pulling the FPC back out again. What I did was to press it gently straight down, using my fingernail to ease it past the hook.
Good luck!
bump...
Yeah looks like all there is on Ebay for speakers is the back one, the one for the receiver earpiece looks like it has two wire connections at each end while the one for the back speaker has them right next to eachother.
So if anybody had this problem, it is very odd and might have to do with the spring connection maybe.
Still I had this problem before and it fixed itself randomly, but this problem came out of nowhere because 12 hours earlier I had dropped my phone on its back and it continued to work fine. Than on my way driving randomly it would not work and I barely set it down in my car.
Once again hopefully somebody has found a part for this because ebay only has back speaker parts.
Best bet is to blow on it and massage it or tap it until it works, damn this sucks because it is basically the very last step to get to after dissambling your phone. So much work to get to such a common problem for many people.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection. Now I am the deusche bag with the bluetooth in his ear all the time.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection.
Click to expand...
Click to collapse
That was what I tried at first. It didn't gain me access to the speaker.
Taking the phone apart is a pain. You really need nimble fingers and faith that you're not breaking the phone when you're levering apart the *very* tightly held together plastic parts. HTC did not make this thing with servicing it in mind. Just be sure to have the right tools (including light and a good magnifying glass if you're over 40) and patience.
Removing the 3 screws that are accessible without disassembling the entire phone will get you in there if you are VERY careful. Unfortunately the one I tried this on did not work differently with a known-good speaker in it. You can delicately dig out the old speaker with a knife (Xacto) and drop the new one in. Takes patients, but not nearly as hard as disassembling the entire phone (been there, done that x10)
I have at least one spare speaker. Maybe more, gotta check my stockpile!
Hey,
My phone got dropped in a rum & coke on Saturday, so i soaked it in 90% rubbing alcohol and let it dry in a rice bath. after 4 days in the rice, it looked dry, so i turned it on. IT WORKS! The screen looks a little trippy (the pattern is even changing throughout the day) but the touch and accelerometer work great. The only real problem is the speakers sound like crap. the receiver is so quiet that it sound like they're wispering, and the back speaker is all crackely.
I found a replacement receiver speaker, but as i haven't taken it apart yet, i was hoping one of you could tell me if this looks correct.
http://www.tvc-mall.com/details/Replacement-Speaker-Earpiece-Receiver-for-HTC-G1-HTCO-G1/photos.htm
If so, i guess i'll order both speakers and attempt to replace them.
That looks about right. Bear in mind, of course, that those pictures are greatly magnified. If you haven't taken apart a G1 yet, you're in for a bit of nerve-wracking prying. Just go slowly and be patient. Getting all the way to the receiver speaker means taking the phone most of the way apart.
Thanks!
I have taken apart a phone before, the Dash (excalibur). I had to replace the screen, it involved removing almost every component.
I think i'll go ahead and order it, and cross my fingers. right now the phone isn't much more then a tiny computer, since i can't hear anyone and i don't have a Bluetooth.

Just repaired my GPS

Prying the frame open wasn't such a problem although you should be careful not to force anything, it actually clicks open nicely when handled carefully. I ran into problems with the little bridge of the GPS, it broke of when I looked at it. Well actually I did help a little with a screwdriver but it broke on touch so to speak.
So there I was with a broken GPS and my sight isn't everything either so what to do. Well I found a solution. Have a seat. This is shocking.
I folded a peace of alu foil a few times and fitted it in the little space on the speaker just left from the gps and covered the broken bridge with it. I wont have to tell how difficult this is considering you have to avoid all contacts in this area. So if you try it it's your choice.
Result. A blasting fast GPS that indeed gives me never seen before fixes. This just must be my lucky day. Geocaches here I come. Time to put my external GPS aside again. Nothing beats a mad hatter.
So you kind of inadvertently upgraded the GPS antennae!
Thanks for posting, don't suppose you could post a picture?
Been checking this GPS thing myself.
I actually wonder how people manage to break that contact. You only have to bring it up a notch.
When checking the back cover you can see that there are 2 places that are contacts. i've checked with the multimeter and both are connected to each other.
Now there is one thing that is strange to me. The contact that is not the one touching the metal 'spring', well on the circuitboard there is this what looks like a piece of conducting foam that would make contact with the other one on the back. Measuring that foam it indeed conducts. It conducts to ground (measured between the coax connector and foam = 0 Ohms).
Now I actually dont know if it really touches the antenna but it would be odd to create a contact when it would not be touching.
So maybe there are 2 places that should make contact to the antenna.
Does anyone have an actual clue, or even better pictures, of the changes that were made on the models after October?

Wifi/Gps/GSM signal strenght issue [Almost FIXED]

Hey guys. Here are a probably fix for wi-fi/sim/gps signal strenght problem after changing the touch or anything similar that needs to disassembly the Mimax2. Well, i found 2 solutions for the problem, but i need someone that understand about hardware to help us. The problem begins when you disassembly the phone, and the pins of the antenna dont plug correctly at the back of the phone. Here are the First solution (that didn't works for me, but maybe works for you):
The video is based in put on the pin a tinfoil to improve the connection with the back cover. I guess that the contact in back cover of my MM2 is very weak, so didnt work for me.
The solution number two is based in connect a copperwire on the pins or on Motherboard to make a homemade antenna. Maybe this way work for me and for who dont have success in the First guide. But as i said previously, i need someone to say If the connections in the pics are correctly. Those pics was found in a telegram group. Some guy made and send them.
Well, if anybody here help me, i'll probably make a video solving the problem. That may help a lot of people having the same problem (they think is a ROM issue, but isnt). I Just need to know where EXACTLY i have to plug the copperwires (fear of burn some peripheal) , and do the tests.
This is ridiculous. Just peel the old antenna out of the old screen, separate the new screen, and put the real antenna in.
You might ask, what is the antenna? Well, there's actually two in one piece of the phone. It's a sticker that the two gold contacts on the original screen were on. The main body is behind the glass, stuck to the plastic. Carefully peel those ends with the gold contact pads up, then from the other side, peel off the sticker they are a part of. The holes are there in all the screens, you just need to carefully push the ends back through with tweezers, then re-glue the glass to the plastic.
It's not easy, but it's not a copper wire hanging out of your phone either.

Resources