just a little tip - Focus General

I know alot of people who have complained about hitting the home or back button while playing a game or something like that and I think I've found a solution. I have the amzer case and no screen protector but this may also work with a screen protector on. Basically what I did was take an old screen protector and cut a very small strip the width of the screen. Then I installed it right above the Samsung logo. Since then I haven't hit the back or home button once. Let me know if this helps anybody.

Great idea, I just did this too. You don't even see it but it stops my fingers from sliding down into that area.

Related

Touch screen stopped working :-(((

Hi,
The touch screen part of my universal has ground to halt to the point that it won't work.
There doesn't appear to be any cracking and I don't recall dropping it or sitting on it.
I work a fair bit outside and can get quite a bit of dust and dirt in my pockets and am wondering if it could be due to dirt getting into the connect on the hinge.
Has any one else come across problems with the hinge?
I'm reasonably adept with a screwdriver - are there any things to watch out for when disassembling to check it over?
Hi..
If u can open with the Universal guide posted in the forum then try clean ing the connectors on the Right and Left of the Clamp Shell part with Iso Propyl Alcohol.
Before opeining you can try pressing mildly with yr fingers, at all the forur corners..it can start working..else do the above...
Hi,
OK, the screen seems to be working OK this morning, however I seem to be getting a sort of ghost effect where it appears as though the phone icon and the volume icons are getting pressed resulting in the volume controls and the phone/flight mode popup appearing on screen.
I guess it is all down to dirty connections.
Do you have a link to the thread about dismantling the hinge, I can't seem to find it.
Thanks.
re isopropal alchol
only use 99% alchol to clean contacts anything below that can cause corrosion on printed circut boards and contacts.
any progress yet.
mine stopped working today too.
but when i took off my screen protector, it worked for a while.. now its dead again.
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
being in Australia I go to the beach allot. with my jasjar.
the sand gets stuck in the sides of the screen putting pressure on the screen and disabling any input. just a thought that it could be the same with u.
hope u sort it out, otherwise claim it on warrenty sooner than later.
The problem I have with the screen is that occasionally the touch screen side of things appears to stop working and also the the volume, wifi and phone dialogs keep on appearing as if I am pressing the relevant icons in the top bar.
I'm guessing some dirt has got into it somewhere or there is a loose connection, but am struggling to open up the screen's case to inspect it.
6680abhi said:
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
Click to expand...
Click to collapse
i took off my screen protector and it worked an hour...
got home, prepared to go to the T-mobile store.. then cleaned my screen ( without protector ) with a small cloth and it was working again.. so weird..
lets wait and see what happens ..
It's not really that weird: If some dust, or something equally small gets between the screen and the plastic frame, it can put enough pressure on the screen, and so the touch screen takes it as a constant (or intermitent) input, invalidating any other action on the rest of the screen.
I just received my Aquapac waterproof (and sand/dustproof) to use my Jasjar hapilly in the beach! :lol:
oh so annoying, my volume sliders keep popping up now..., as if some one keeps tapping, cause when not in Land scape mode when i open the "START" menu. it scrolls down, the same input/tap as wher the volume is in Landscape mode
There must be something wrong ... my screen still isnt working properly
one possible solution for touch screen not working
guys.... although I dont need to register onto this portal and it took me 15 minutes to register (fault of my own) but I got so much relieved with the solution that it deserved 15 minutes of my effort ;-) I hope it helps someone...just like it did help me....
I own a P835 Asus mobile and from past 2-3 days was having problems - start menu continuously appearing and my taps not getting recognized. Since yesterday my screen suddenly stopped responding to any taps or scrolls altogether.... buttons were working fine but not the screen..... i spoke to the facilities centre this morning and was about to take it to the shop but due to my laziness...didn;t go.....
Thanks guys.... what you mentioned above is very correct.... it was just a tiny molecule of dust that the screen was interpreting as my input and finally refusing all my taps..... I just cleaned the screen and the speaker side with the mere stylus n things started working.... thanks a lot.... more than laziness was this worry cause I just bought this piece a month before....
so people...before takin it to the shop....try this one too.....huhhh.....

Front screen only GLUED on? It is popping off!

Okay, I read that someone lifted part off the front by removing a screen saver! Now with me, I recognized that on the left side bottom, left to where the slideview and call buttons are under, the ENTIRE part seems to come up.
It is lifting itself and I bet in a few days/weeks this will get off.
So my question is if anybody had this happen and knows what is under there? Is there a possibility to GLUE it back on?
Now since I am watching this, I think the ENTIRE front can come off eventually and if it is just glued on at the bottom where one has to press the buttons all the time, it is only a matter of (short!) time until this gets out of hand.
Anybody found anything about taking this phone apart yet?
That happens to my phone, I do not bring it back because I buy it in a duty free shop here it japan and also that is the only issues on my phone and only some bugs. I just press it always there to bring it down but it keeps popping up. I think i can glue it, so I do it to fix the problem. Just be carefull if you do it, I notice that under the plastic screen there are buttons (as I think it is) the hard part that you feel when pressing the slideview or call. When you use a liquid glue and put to much, it can go to that button and worst may stuck that part or go inside the phone and also the part where the mic is. I put glue just on the sides just make sure to put small amount at a time. I cannot give the brand of the glue that I use because its in japanese.Now only the small part in the call buttons is up a little because I cannot put enough glue on that part, but in the slide view button its now okay and working well.
This is my firts post on xda hope it helps a little.

[Q] Capacitive button tester

Is there a tool that can test/adjust the sensitivity of the Epic's capacitive buttons? Mine seem unresponsive and I'd love to know if the hardware is not sensitive or the software is ignoring the taps.
Something that displays a readout showing which button is being pushed would be really useful.
Thanks,
Jason
there really isnt. its being classified as a hardware issue. i swapped the board out on mine the other day with a returned phone and it started working. taking the phone apart to fix the button at the bottom is a complete pain in the face. and if the gorilla glass faceplate comes out (which needs to happen to swap out the buttons) then it never really goes in correctly. nor does it stay stuck.take it back to sprint and see if you can do a 30 day exchange on it.
Thanks. I got mine at Best Buy and have their insurance. They'll fix/replace it for free but they have to send it to their service center and give me a loaner. I almost replaced it within the 30 days but when I took off the screen protector (Skinomi) to give it back, the keys were working great. I decided to hold on to the phone. Now I have another protector on it (Realook) and am having the same problem. I'm assuming the button is less sensitive than it should be so it works fine without the protector but not well with it. I might have to switch to a partial-screen protector.
So if my buttons are very difficult to press then its an issue and not the general design of the phone itself?
My wife said she has no problems with the buttons so I'm going to have to compare hers to mine.
jasonsf said:
Thanks. I got mine at Best Buy and have their insurance. They'll fix/replace it for free but they have to send it to their service center and give me a loaner. I almost replaced it within the 30 days but when I took off the screen protector (Skinomi) to give it back, the keys were working great. I decided to hold on to the phone. Now I have another protector on it (Realook) and am having the same problem. I'm assuming the button is less sensitive than it should be so it works fine without the protector but not well with it. I might have to switch to a partial-screen protector.
Click to expand...
Click to collapse
Same exact situation. I was using the Realook screen protector and everything worked fine except for the back button. After I took it off I noticed that the back button worked just fine. After using it a little longer I still feel like it's not as responsive as the other three buttons.
jasonsf said:
Is there a tool that can test/adjust the sensitivity of the Epic's capacitive buttons? Mine seem unresponsive and I'd love to know if the hardware is not sensitive or the software is ignoring the taps.
Something that displays a readout showing which button is being pushed would be really useful.
Thanks,
Jason
Click to expand...
Click to collapse
There's a couple of ways you could do this:
Every time you press a capacitive button, it should blink right after it registers. This indicates it was pressed.
Another way is to boot into Clockwork Recovery Mode, goto Advanced, and use the key/button test option that's in there.
I'm also using a Realook screen protector, so far it's the best I've tried. I've used Zagg, Invisishield, StealthGuard, and Amzer protectors and non of them had the clarity or feel of the Realook. It feels and looks like nothing is there, aside from being an oil magnet. Anyhow, I don't have any reduced sensitivity when using it compared to bare.
One trick I use to apply the Realook is cover the whole phone with 4 or 5 strips of scotch tape (overlapping each other) before application, it helps to get rid of all the super fine dust particles that are floating around. Also, use a high power flashlight, and shine its beam across the surface of the screen, it will make all the dust you couldn't see before light up. Have a few looped pieces of scotch tape ready to pluck off dust particles that get stuck on the protector and screen. Then get the Realook protector ready, pull your strips of scotch tape as one from the top and quickly align the protector, pull more tape off and follow with the protector, this insures no dust thats floating around will get on your screen or protector, if some does, you have the flashlight to easily show you and the tape at the ready to pluck them off.
Reason I said the above is because you might have minute dust particles that are creating a gap with just enough space to prevent your capacitive buttons from registering.
I took drastic measures and cut a rectangle hole out of the Realook protector so I could have direct access to the buttons. It is ugly, but it works. The back button works much better now.
Jason

Ghost screen touches

Just got myself a transformer today and it seemed great, however right after about 5 minutes the thing goes nuts like someone is swiping or touching the screen. Mostly just one spot on the left side and it will do it whether I'm holding it or it's sitting by itself. Can't seem to find anything posted about this wondering if thats because it's not common or I'm just not looking for the right stuff? Any help would be great, will likely return it tomorrow anyhow but if there's a fix would be nice.
Yeah, I got this as well while playing Angry Birds (F'd up my scores ! ). I don't know if it will work for you, but I just cleaned the screen really well with a cotton ball and alcohol, dried it, then used a microfiber cloth to clean it up (the ones that come with glasses, screen protectors). It worked for me, i think there was some gunk on the screen and was registering as a touch..
Try a factory reset and if it doesn't work take it back for a new one.
Thanks I can't see it being something on screen but will give it a wipe done here in a minute. Also tried the factory reset seemed to help but still getting in same frequency just not as badly. will see if the cleaning doesn't work I'll take it back and replace it.
This is the biggest annoyance that I have as of recent.
I have particularly oily fingerprints which causes smudges constantly.
I love the sensitivity of the TF, but if there is excessive smudging, the residue will register as a screen input - Wish the sensitivity could be adjusted.
Weird things happen when I need to clean the screen... I.E. I will be using a browser and use a single touch to scroll down, but it will zoom in/out instead; the long press menu will show up in a random spot persistently; -or- the screen will be completely unresponsive.
When this happens - I turn of the screen, clean it, turn the screen back on, and I'm good to go (note: sometimes I cannot even see any smudges where I am having issues).
This happens to me FREQUENTLY when i use the tab outside during humid days. I am thinking a screen protector may help, but still havent gotten one to try it out.
I had this same problem before the touch screen completely stopped responding on me.
For mine it only happened after waking it up from sleep mode though. When I turned Timeout to Never the ghost touching stopped.
Well tried as suggested the cleaning of the screen and all that but it still did it so took it back to the store got lucky and they still had one left, and exchanged it. New one hasn't had any issues at all. Thanks all.
I just took mine out of the box for fun (it was packed up for rma) and when i turned it on the touch screen worked. The ghost touching stopped to. But i still have a strip from top to bottom on the right side of the screen that registers two touches . So ill probably still send it in for a replacement.

automatic screen shut off

So I've browsed around and there are plenty of screen issues, but I haven't seen the one I'm experiencing nor have I seen a solution. When I press the power button my screen comes on and turns off right away. Sometimes a few seconds after I hit the power button sometimes even longer. Most times I won't even be able to put in my security pin to unlock the phone. I see people saying Verizon will do an update soon but that isn't good enough considering I can't use the phone. I did find a loop hole to this problem. Quick start the camera with the volume down button then press the home button after the camera loads and it won't shut off by itself. I thought I'd post this method up for others having this frustration.
If this particular problem has been discussed and beaten to death then the mods can close the thread.
I've got a YouTube link but I don't have 10 posts to show you. Search for user name "vfreeza" and it is the only video I've uploaded. You'll see my first time turning the screen on was using the quick camera method and the times after is with just the power button. The screen turns off without even my hand touching the phone.
don't cover the sensor on the upper left hand side
Yup I read that too. My fingers rest at the corners of the phone and I've tried the not cover sensor thing as well, makes no difference.
Wish I could disable the sensor. I hate this problem
Sent from my LG-D802
Just a quick update. I bought a Diztronic tpu case and the moment I put it on all the problems went away. Screen acted nornal and knock works. My guess is without the case my hand is making some kind of connection it shouldn't be when I'm holding it without a case.
wholemilk said:
Just a quick update. I bought a Diztronic tpu case and the moment I put it on all the problems went away. Screen acted nornal and knock works. My guess is without the case my hand is making some kind of connection it shouldn't be when I'm holding it without a case.
Click to expand...
Click to collapse
Did your old case hug the bezels tight? because it tends to mess with the digitizer perhaps the incipio feather case? or a plastic case of some sort? just curious im pretty sure that was your problem cause if you barely press on the screen youll notice waves in the lcd screen and since the bezels are so small on this device some cases can do that.
Cyko.Tech67 said:
Did your old case hug the bezels tight? because it tends to mess with the digitizer perhaps the incipio feather case? or a plastic case of some sort? just curious im pretty sure that was your problem cause if you barely press on the screen youll notice waves in the lcd screen and since the bezels are so small on this device some cases can do that.
Click to expand...
Click to collapse
The phone was naked, no case at all.
wholemilk said:
The phone was naked, no case at all.
Click to expand...
Click to collapse
thats extremely odd but im glad you got it fixed!
Thanks! This case is never coming off! haha
My phone has that very problem and it's driving me insane.. i love this phone, but it truly is a hassel to use it after its been idle for awhile.. or at night... hands no where near the sensor or anything, it could be laying straight up or down n itll still have that problem.. thanks for reading.
I normally just wipe the sensor area, n it magically starts working again.. n i don't touch it, n the problem comes back after awhile....
Also naked phone besides screen protector, but it's not covering up the sensor.
My phone does the same thing. It's so ****ing annoying.

Categories

Resources