[Q] i cant get root, stuck at step2 - Legend General

i followed the downgrade procedure and successfully downgraded to 1.31.405.5... but when i get to step2 on the root procedure, it just gets stuck at the exclamation point screen...
i have hboot 1.01... could this be the problem?? how can i solve this?
i need root access because i want to install the official CM mod... i hope someone can help me...
thanx for reading...

ok here's whats happening..
step 1 on rooting procedure seems to finish well..
step 2 it says error:device not found
anyone can tell me what im doing wrong?

Make sure you are in recovery mode aka the screen with a ! inside a triangle
Also make sure you are running HTC sync 2.0.33 or older otherwise it won't work

i did all that still my device isn't detected... seems like my legend isn't detected when on recovery mode... anyone knows how this can be done?
also my goldcard is at mmc0.. is that okay?

That should be no problem as long as it's been formated since the goldcard aka your SD card should be blank to do step 2.
also did you downgrade to 1.31 before starting?
what rooting guide are you useing?

First, it would be nice to know what kind of tutorial you're following.
Then, I had some similar issue when I wanted to root my Legend. My windows Seven won't recognize my phone in recovery mode. In order to make it to do so, I had to :
- uninstall HTC sync
- install ADB (and do the stuff in the PATH variable)
- then put my legend into recovery mode
- Plug my phone when in recovery mode
- Then re install HTC sync
Now my legend is recognized by my computer, even in recovery mode.
Have a try and tell us !

Hi! im follwing the Unlockr guide...
@50-3
yes i downgraded to 1.31.405.5
@Greedybro
i'll give it a try, THANX!

Is it 64 bits Windows?
Sent from my Legend using XDA App

another thing to try is removing the HTC drivers from device manager then install HTC Sync 20.0.33 then try
also usfull adb command is "adb devices" it will tell you if your device is seen a lot easyer then waiting for the step2 script to say no devices

@sckank - 32bit windows xp sp2
@50-3 - no device detected when i use adb devices on recovery

step 1 finished but i get 2 fail messages
writing 'zip' .. INFO adopting the signature contained in this image.... INFOsignature checking...
FAILED (remote; 12 signature veryfy fail)

i might not be actually stuck at step2... coz step1 is giveing me errors... i hope someone can help me...

There is an alternitive way to do this i have not tryed rooting use this method but possible work head over to http://forum.xda-developers.com/showthread.php?t=698404 grab the files follow the guide you should be able to do part 8 and 9 without doing part 7 (step bat file)

@50-3
isn't it only for rooted legend?

shara6 said:
@50-3
isn't it only for rooted legend?
Click to expand...
Click to collapse
Not sure possibly but if nothing is working i thought it might be worth a go at least
@shara6 BTW did you make sure that the first 2 numbers in the mmc was 00?

SOLVED! my gold card got corrupted i think so i had to redo the gold card procedure...
thanx a buch for all your comments!

Related

[SOLVED] Connection Error [262]. Stuck in bootloader (tri color) mode.

I'm new in these forums as well I'm new with flashing ROMs so obviously I messed up flash process and my device stuck in bootloader (tri-color) mode. This post I address to those unfortunate like me .
# Symptoms #
- ROM flash started and stopped at 17%. After recovery flash process stucks at 0% and pops Connection Error 262. Device is stuck in bootloader mode not possible to flash anything, hard reset does not help, flash from SD card does not help either.
# Possible cause for that #
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
2. Connection between ActiveSync and device was not established when flashing ROM file.
Before to go any further please take your time and read Polaris Wiki to get familiar with glossary and acronyms used here.
PROCEED ONLY if flashing original ROM does not help, hard reset does not help and flash from SD card does not work.
# Solution #
1. Download MTTY software.
2. Kill ActiveSync (Press Ctrl-Alt-Del and stop rapimgr.exe and wcescomm.exe processes).
3. Plug Polaris into usb port (Plug directly not through hubs).
4. Start MTTY after chose USB from PORT dropdown list (if it is not listed there then ActiveSync processes were not stopped).
5. in window type: set 16 0 (enter cmd mode)
6. after type: task 8 (this will format phone)
7. after type: task 0 (this will restart phone. Not always necessary)
8. soft reset
This procedure can damage your phone. Use it as last resort.
Official source in french here.
Now before flashing any ROMs read carefully how to flash (not install!) Hard SPL.
# P.S. about install and flash termins #
This error with flashing happened to my due misunderstanding between notions of installing something on your device and flashing. In my opinion those are completely two different things. As for first I understand of running some cab or exe directly on device. So problem comes when people sees install Hard SPL en device as they try to find some cabs or exes to install directly on device or they just copy all files to device. To make things clear Hard SPL "installation" actually is ROM flash process which must be done with maximum caution, but those who did not read Wiki won't understand it.
Cheers, whitealien
BiG THX @ Whitealien.
works to 100% on my Touch Cruise.
I flashed under Vista Ultimate...
# Solution # ... addition from me for Vista users!
....
2. Start Windows Mobile Device Center and Deaktivate USB Connection and then start Task manager end kill
Process wmdc.exe.
Rest of whitealien. and have fun!
Thank you!!!!
I had given up on this, and was sure my only option was a warranty repair :O
always welcome
Thanks, you've saved my Polaris.
Mine didn't want to react anymore to the soft reset, so I replaced your instruction 8 with:
Cmd>boot
and that did the trick.
whitealien said:
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
Cheers, whitealien
Click to expand...
Click to collapse
I had exactly the same problem, for whatever reason went back to original SPL before HARD SPL.
I solved my issue by using back the original original HTC RUU_signed.nbh and flash it using the CustomRUU.
Thereafter, repeat the entire HARD SPL and flash the home cooked ROM.
Cheers.
For unbricking your HTC Polaris, you can try also a hard-reset (if it is related to a software error):
http://www.hardreset.eu/htc_touch_cruise_polaris_hard_reset_soft_reset.html
Thank you very much
you really helped
thank you again
mrfone2003 said:
Thank you very much
you really helped
thank you again
Click to expand...
Click to collapse
you are welcome.
Seems people are still falling for this error.
I'm has this error.
Solution (with SPL-2.20):
- kill ActiveSync (process, not uninstall)
- cable to USB on motherboard
- hard reset on phone
- connect to cable
- flash OFFICIAL rom
Two time I revive my Polaris.
help me please
hi.I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help
thanks for the support
Thanks dudes for the great help you gave to recover my htc dual from bootloader screen. I am very happy to have my phone back. Thanks for everybody for the help they have provided generously. I appreciate alot. infact thousands times.
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
aaront1988 said:
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
Click to expand...
Click to collapse
Did you follow all steps from 1st post?
Did you kill all running ActiveSync processes?
I did indeed, i'm on vista so didnt have those particular processes going but followed the step from Aeroman and it still doesn't want to play. Any ideas?
managed to find a working XP machine and it worked a treat. Thank you so much.
thanks,this solved my pb
please help
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
wesram said:
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
Click to expand...
Click to collapse
What did you do to get there?
whitealien said:
What did you do to get there?
Click to expand...
Click to collapse
hey, im sorry for the late reply. it didnt notify me and now after posting several times asking for help in many threads by accident i bumped into this thread again to see that u answered and thank you so much.
now, what i did? this is the wierd thing, i didnt do anything, i went and back to see my phone stuck in bootload .... after this i tried almost everything i can find. from ur solution to flashing original rom to hrd spl to .........
now all gave an error except the original rom (polaris.1.28.415.2), it did went to 100% and device restarted to take me to my nightmare .... another bootloader screen am i suppose to search for polaris 1.28.0000?
i still have now the same writing shown.
please help me with this, its a nightmare .... is it totaly dead???
i managed to catch what it is saying b4 bootload screen (only when SD card is in place) it says no image file was found!!! in a very fast way and go to bootloader. in case the sd is not in place nothing happens and it goes straight to the bootloader

[170] USB Connection Error

I tried to root my Magic however it has perfected SPL 1.76.2008 so I tried the goldcard method but I only managed to change the firmware from 1.6 to 1.5. I cannot use fastboot so now I'm trying to install a new RUU so that I can follow the steps to install CM however I get the USB error (on windows 7).
I already tried reinstalling the latest HTC Sync and that seems to recognise my phone but when I open the Setup for RUU, Sync doesnt recognise it anymore until I close setup and replug USB. And yes, I inserted the goldcard already. Any help is appreciated.
I have pretty much the same problem here, but I do not have a goldcard (which I dont thing its necessary). When I try to transfer some file to my phone, it starts and after a couple of seconds, unplug from storage mode (Robot turns green again :[ ).
I have Cyanogenmod 6.1.0-DS and Windows 7 32bit.
Even over wifi, this happens. Seems to me thats some storage problem with the rom, but cyanogenmod is widely used and tested.
Can someone help us?
Debugging on?
Of course, I followed every single step correctly maybe theres a problem with windows 7.
BMN12 said:
Of course, I followed every single step correctly maybe theres a problem with windows 7.
Click to expand...
Click to collapse
On linux now and had forgotten this. Reread everything from the beginning and recalled that I've had issues with the drivers from HTC Sync driver not working when I had downgraded my G1.
The "official" google sdk driver covers all builds and modes (RUU uses adb mode.) Maybe try reinstalling with them instead?
Kind Regards,
Kevin
Sent from my T-Mobile myTouch 3G using XDA App

[Q] Flashing rom for htc touch HD

hey guys..hope to be in a good health
this is my first theard ever here.. and honstly i found xda more useful,more likly to me rather than any websits else..so i'd like to thank guys here "u rocks guys "
now i'd like to ask about flashing anew rom for my HTC touch HD t8282
running win-mo 6.1 with arabic supported language..touch flow 3d..etc
but now i'm bored with original rom and i was looking for some roms around here and i found what i excatly wanted
but..(i'm sorry for that question :$) i dun know how to flash a new rom to my blackstone..i used search fuction and dummies guide also but..rofl i didn't get what they were takin about
so i was asking if someone could provide me with smplified way to install a new rom using HSPL
Thanks in advance and sorry for z long topic ​
basically, flashing a winmo phone is an easy process:
1. bootloader mode (power on with VOL- button pressed)
2. flashing
3. hard reset
however, there are a few preparations if your device was never flashed before, you need to install hspl on your phone and make sure you have the correct driver installed on your pc. the driver for the device in bootloader mode might vary from the driver used to sync the device, when switched on.
1. the driver:
if you have windows xp, connect the phone in bootloader mode and look, whether it changes from serial to usb on the bootloader screen, you should be fine by then.
on windows vista/7 you connect the device in bootloader mode, and might actually take some time for it to download another driver from windows update. if it changes from serial to usb, first try to connect using mtty, before attempting to flash, because the connection might not yet be stable and you might want to have a look at the thread (ref updating the usb drivers).
2. hspl
to quote the dummies' guide thread:
(HSPL2a) Place your phone into its bootloader.
(HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
(HSPL2c) If successful, go to step HSPL3. If the flashing process sits at 0% and you get Error [260] connection after some time, go to step (Troubleshooting).
pretty easy, in other words, just connect the device in bootloader mode and run the package on the pc, it will unlock the spl and flash hspl.
if all went well, you are ready to flash, download any rom you like from the rom development section, and flash it using the .exe file that comes with them, might be updater.exe, blackstone RUU.exe or something else. if your rom download only consists of an .nbh file, like ruu_signed.nbh or BLACIMG.nbh, download advanced RUU and use it to flash.
alternatively, if this is to complicated for you as a beginner, you can rename the rom file to BLACIMG.nbh (if it is not already named like that) and put it in the root of the sd card, by then entering bootloader mode, it should find the rom and give you detailed instructions on how to install it.
last step, hard reset, as described in the original manual, switch on, while pressing VOL- and VOL+ and follow the instructions onscreen.
Chef_Tony said:
basically, flashing a winmo phone is an easy process:
1. bootloader mode (power on with VOL- button pressed)
2. flashing
3. hard reset
however, there are a few preparations if your device was never flashed before, you need to install hspl on your phone and make sure you have the correct driver installed on your pc. the driver for the device in bootloader mode might vary from the driver used to sync the device, when switched on.
1. the driver:
if you have windows xp, connect the phone in bootloader mode and look, whether it changes from serial to usb on the bootloader screen, you should be fine by then.
on windows vista/7 you connect the device in bootloader mode, and might actually take some time for it to download another driver from windows update. if it changes from serial to usb, first try to connect using mtty, before attempting to flash, because the connection might not yet be stable and you might want to have a look at the thread (ref updating the usb drivers).
2. hspl
to quote the dummies' guide thread:
(HSPL2a) Place your phone into its bootloader.
(HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
(HSPL2c) If successful, go to step HSPL3. If the flashing process sits at 0% and you get Error [260] connection after some time, go to step (Troubleshooting).
pretty easy, in other words, just connect the device in bootloader mode and run the package on the pc, it will unlock the spl and flash hspl.
if all went well, you are ready to flash, download any rom you like from the rom development section, and flash it using the .exe file that comes with them, might be updater.exe, blackstone RUU.exe or something else. if your rom download only consists of an .nbh file, like ruu_signed.nbh or BLACIMG.nbh, download advanced RUU and use it to flash.
alternatively, if this is to complicated for you as a beginner, you can rename the rom file to BLACIMG.nbh (if it is not already named like that) and put it in the root of the sd card, by then entering bootloader mode, it should find the rom and give you detailed instructions on how to install it.
last step, hard reset, as described in the original manual, switch on, while pressing VOL- and VOL+ and follow the instructions onscreen.
Click to expand...
Click to collapse
thnx 4 help really usefull and easy,i apperciate it
thnx again
@ blackspyker
did you successfully flash the hspl and a new rom?
(just seeing if this thread is solved or not)
Rn
just like me dear, please help us. but mine is English version
just like me dear, please help us. but mine is English version
blackspyker said:
hey guys..hope to be in a good health
this is my first theard ever here.. and honstly i found xda more useful,more likly to me rather than any websits else..so i'd like to thank guys here "u rocks guys "
now i'd like to ask about flashing anew rom for my HTC touch HD t8282
running win-mo 6.1 with arabic supported language..touch flow 3d..etc
but now i'm bored with original rom and i was looking for some roms around here and i found what i excatly wanted
but..(i'm sorry for that question :$) i dun know how to flash a new rom to my blackstone..i used search fuction and dummies guide also but..rofl i didn't get what they were takin about
so i was asking if someone could provide me with smplified way to install a new rom using HSPL
Thanks in advance and sorry for z long topic ​
Click to expand...
Click to collapse
download this, extract all the files, take micro SD out of device, connect device to active sync and then run HardSPLWrapper_Blackstone.exe on your pc, it will now start to flash a new SPL, when complete confirm you got it installed, go into bootloader mode (tricolour screen! {hold volume down and press the reset button under the back cover}) now verify the screen shows 1.56.OliNex, which is the new Hard-SPL version.
when complete you will be able to flash any rom to your touch hd/blackstone
note: if you do not flash a new rom you will have graphical issues with the current rom, however this gets fixed as soon as you flash a new rom
if you have any trouble, click me and go to the first post
good luck

[root]HTC Legend

Hello
Due to an issue of loss of storage on my HTC LEGEND, I decided to switch to root and supporting the solution DATA2EXT. That's how I followed this tutorial ( can't post the link, so it's the tutorial from FRAndroid, sticked on the HTC LEGEND part for root). I'm stuck at 2. ROOT, when I start the step1-windows.bat, my phone displays an HTC logo on black and ... nothing happens.
thank you in advance for your help
Meanwhile, my phone is in a very old version, which is not very pleasant to quotidient: /
thanks
what does it show on your pc... i mean the commands on terminal window...
what's your software version?
if it's 1.31 or lower it's ok... maybe u haven't made gold card properly
On my comp :
Legend Root Step 1
Erasing cache and rebooting in RUU mode...
erasing 'cache'... OKAY
... OKAY
About to start flash...
< waiting for device >
sending 'zip' (121756 KB)... OKAY
writing 'zip'...
on my phone :
a htc logo with a black background
i'm on a 1.31 & i check my gold card few mins ago
thanks for help me
Ok, so i pass the step1-windows.bat
now... another problem, when i go to recovery mode, adb didn't find my device ... : /
adb devices return nothing
when i kill & start adb, it's the same .
Make sure you have the right version of HTC sync installed.
http://forum.xda-developers.com/showthread.php?t=894465
Has a link to the corect version
I reply to french forum.
Good luck
Thanks all for your answer
yes i'm sure i got the good htc Sync.
When i'm in recovery mode, nothing is recognize as ADB or something like that. I think the problem is here ..
do you know how run it ?
thanks for all your answer
no idea ?
plz help me, this gonna take my head
Maybe this helps. Sounds like USB brick.
You must be rooted to try the following, it seems you can't write to mtd0 without root.
Click to expand...
Click to collapse
i'm not rooted : /
i'm still trying this. thanks for the info
[edit] i can follow this tutorial cause i haven't permission
I have the same problem.. No solution found yet...

Bootloader not detected at PC

Hello,
Today i have tryed to flash a new CWM on my HD2.
But i get always an error "USB init. Failed" so i've searched in google an in this forum for an solution but i haven't find any.
I've tryed to flash CWM in Bootloader mode but my pc's (2 XP ones and 1 Win7) don't detect my phone.
Please Help
install windows mobile device center to your pc.otherwise it doesn't recognize it.
I have installed WMDC. But it doesn't recognize it at all.
but cwm isnt flashed from bootloader? r u using magldr or clk?
MAGLDR but also in Flasher mode nothing happend. In WMDC i have already disabled USB Connections but also -.- nothing
try another pc. and last solution format pc(i did so a few weeks ago when i met the same problem)
after last time i formated my computer imy phone wasnt detected in computer ...in bootloader i couldnt see USB just serial ...i just installed activesync ...and right after phone was detected ...so try to install activesync and see
[q] htc hd2 flashing rom issue
Can anybody help me.I have MAGDLR and the Bootloader installed by a previous chap who owned the phone, all the correct versions. THe phone HD2 (T-Mobile), when I got it, had Gingerbread on,but the FM radio was not working,
so I thought an Upgrade was in order. I went to the MIUI website and downloaded the latest stable rom and followed the instructions as best as possible, but I had problems with the
Bootloader going from Serial to USB and being able to flash the rom like that. I then tried the loading the rom ZIP file to the SD card, and then using Clockwork orange recovery to
to install the ZIP file from SD card. That being said, I rebooted and the phone just stayed hung on the HTC logo screen. (And I didn't do a back up, before I started.)
I eventualy found a Jaws MIUI rom, that instaling via Clockwork Orange, worked, but it is Froyo and not a lot of stuff works very well. What is the correct procedure to install
from SD card, with Clockwork Mod Recovery? The Roms that I download, do I have to unpack the zip, do something on the files? I have read that depending on the rom that you have, when
doing a ClockWorkMod Recovery installation, that you need to have the right Size partition or image disk version of the Clockwork recovery MOD, But I can't swap and change this as my USB does not work between the phone and the PC.
I have installed active sysnc, does not work and I have tried this both on my Desktop and Laptop. As the one response suggests, Formatting your PC seems a bit extreme.
Help, Pleeeeeeeeez!
Thanks
Asdoos said:
Hello,
Today i have tryed to flash a new CWM on my HD2.
But i get always an error "USB init. Failed" so i've searched in google an in this forum for an solution but i haven't find any.
I've tryed to flash CWM in Bootloader mode but my pc's (2 XP ones and 1 Win7) don't detect my phone.
Please Help
Click to expand...
Click to collapse
try with another usb cable
After many tests with other PC´s and USB cables and different Windows / Linux installations I have noticed that my phone doesn't charge -.-
I think its an Hardware Porblem of my Phone. Does anyone know how to fix it?
Usb port is gone on your phone get it replaced.
Sent from my HTC HD2 using XDA App
Hello, I'd love to mention one thing bec I got the same problem like some fri. No need to worry fri.My problem troubleshooting is " Just install Windows Mobile Device Center". Thanks all and I love xda.

Categories

Resources