Database Users

Bricked my S200 after installing jasper AKU3.3 plz help!

hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!

did try upload another rom from bootloader ?

did try upload another rom from bootloader ?
but first try a hard-reset

i don't know how to load a rom from bootloader (i allready have made soft and hard reset

no one could help me ?

1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!

i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?

while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.

this rom don't work, it give me the message
error 294 invalid vendor id

it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much

pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right

Firmware 614c update failed !! HELP !?!

Hello Guys,
i am getting crazy witch my ipaq. I downloaded the newest firmware for my uk ipaq. I startet the HP RUU and everything was ok, till my notebook chrashed during the firwmware update....
So my ipaq only hangs on the start screen. What can i do ? I`ve read here in this forum that someone started the SDLoader and the RUU found the ipaq and startet an new update. But i dont get it work, i tried it several times, but my computer doesnt recognize the ipaq ?! (In the Device Manager there is no new usb device)
The Ipaq shows after the SDLoader started: Update Error! Pls Check!
What i doing wrong ? I am getting crazy with this thing !!! Please help, or please can someone give me a tutorial for a noob (i am not one, but now i think i am...) ?
Big THX
P.S.: Sorry for my bad english, i am a portuguese man...

You can check this:
- connect ipaq (running, no matter what error on the screen) to pc, run hp upd utility, try to update
- run SD loader, and the same way - connect to pc, run hp upd
- try hard reset (?)
I hope one of this helps. If no, I have on idea besides hp service.
Regards,
Darek

How i can run the bootloader mode ?
Is this the same as the SD Loader Mode ?
Big THX

I got my baby back, YEAH !
I only flashed the Windows from this Page
http://4pda.ru/forum/index.php?showtopic=79455&st=120
and then Windows-Screen showed up. So then i could install the new firmware again and now everything is ok.
So possible this can help anybody if he bricked his 614c !!
Bye

Anyone can help to publich a full guide to flash rom for B7610

Anyone can help to have a complete guide to flash rom to my b7610 ?
besides, any rom which really able to download? Many links are dead and unable to download.
thank a lot

1. Intall Samsung SDMA drivers.
2. Launch Flasher. Select files (only PDA Image for custom ROMs)
3. Push Detect yhan connect device.
4. When PDA1 becames green and apiers button Start Downloading - push it and wait about 10-15min.
Recomended to do hard reset before and after flashing.

[q] i cant entering into xrecovery after use 2.3.3 rom

PLEASE HELP
TWO DAYS AGO I RESTORE MY BACK UP ROM 2.3.3
CM7-J005 VIA XRECOVERY
BUT NOW I CANT ENTERING TO X-RECOVERY, EVEN I HAMMER BACK BUTTON AND TRY FOR SEVERAL TIMES
AS I REMEMBER I DONT UPDATE MY BUSYBOX
I NEED TO CHANGE MY ROM,... PLASE HELP
SORRY FOR MY BAD ENGLISH
THANKS

If you really need to change the ROM just run SEUS and root again.

SEUS? What for? If the ROM is booting and working then all that must be done is to reinstall xRecovery manually and try to get into it again

if you install b box installer and xrec you will get it back as i had the same problem hope that help

thanks for the advise, now i found how to go to x recovery by push power button twice when se logo came out .....
cause i usually use back button
thanks guys

[HELP] Brick after update TA.1021

hello guys
my nokia 6 ta 1021, after update remain in black screen
i read some guide to unbrick but ive a problem, the qualcomm flasher when click to browse emmcxxxx.mbn file in firmware, cant find it...i dont know why, then i try to use ost l flasher but not runnin nevertime
someone have a good advice to solve this problem?
thanks

any help guys, please?

First of all do ?% battery charging ur bricked mobile, connect to pc and install custom TWRP then install any nokia 6 rom.