Put transparent tape on the front speaker and put a snap on cover case which covers the small gaps aroud the screen no dust can come in then, speaker can be heard even with the tape. And for the bottom gap also put tape to seal it since the snap on case don't cover that area and that's it folks how can dust get under the screen now that all gaps are seal. I'm gonna try this when my replacement comes in and try it and let me know how it works for you
Eh... The screens are sealed unless something happens to them. So if you have lots of dust under your screen... just get it replace. HTC will be more than happy to do so if you've got tons of dust under there.
Related
i have been trying to figure out whether there is a screen protector attached to my xperia play which was bought form germany.
Can anyone infom me how to make certain that there is a screen protector attached. As I would iike to know if i see scratches on it that those scratches are only on the screen protector and not the screen itself.
From the other threads ive seen. The one that comes already on the phone when bought is some sort of shatter-proof layer. So in a way it is a screen protector (and a pain to get off apparently).
But i installed the spare from the box to prevent the one on the screen getting scratched. I havent noticed any difference in the screens responce so all is good. Better safe than sorry
The screen protector comes in the box, not attached to the phone
An easy way to test if it's on the phone is to take a piece of tape, put it on a corner of the device, and slowly peel it back. If there's a protector on your screen it will lift off with the tape. You don't need to pick at it or use a hair dryer. You can use more tape to 'dab' off bits of dust, hair, crap too before letting it settle back down. Just squeegee out the bubbles and you're in business.
I smashed the screen on my Tab a few weeks back. While I didn't take a video of the replacement, here are some notes and tips on my experience:
If the glass is cracked but you can still see the display fine (i.e. no rainbow or black ink spills) then it is just your digitizer that is broken. Your top priority at this point is to not break the LCD because the digitizer is relatively cheap (~$35 shipped from China, $60 from the US). This also goes for the picture being fine but the touch not working at all.
Buy a replacement digitizer. I got mine from ebay ( http://www.ebay.com/itm/270938561127 ).
Gather tools:
A clean towel to use for your work area to prevent scratches and scuffs
A little plastic prying tool (likely to come with your ebay order)
A thin and sharp utility knife/razor
A three prong screwdriver. The seller I used sent a few other screwdrivers but not the three prong one. I used one I got from a Nintendo DS repair a while back.
A heat gun will make this a lot easier. I guess a hair blow-dryer might work in a pinch.
I did not see any good videos for the disassembly. The one I watched ( http://www.youtube.com/watch?v=thTt6G27NV8 ) really screwed me over because it didn't show removing two screws first.
Here are my written steps for replacement:
Use a needle to pry out the two caps on either side of the USB charging port
Use the three prong screwdriver to remove those two screws
Insert the pry on the bottom middle between the plastic frame and the glass. Push down firmly so it wedges in up to the L shape.
Slide the pry along from the middle to either end and around the corner. You will feel the frame pop away from the innards.
Continue working the bottom half of the frame apart until you can insert tweezers or something else under the unit and lift it up and out of the frame.
Be careful to lift the bottom half then pull it out away from the top. Otherwise, you will crack the audio port which extends from the unit and fits into the hole in the top of the frame.
Set aside the frame and place the unit on a clean towel. If you have a broken screen, you are going to be dealing with lots of tiny slivers of broken glass.
On the circuitry side of the unit, you will see three big flat ribbon cables. The middle one is the digitizer. Use tweezers or the pry to *gently* lift up the tan colored plastic locking hinge on the far side (opposite the cable). It will pop up and the cable will easily slide out. Go very slow and carefully here. Don't mess with the black plastic because it will chip right off.
Now comes the painful part. Removing the old digitizer. Take a cigarette break if you need one. Maybe a Valium. Basically, almost all of the black trim part of the glass is thick strong glue binding it to the unit. You need to separate this glue to be able to peel the glass digitizer away.
Hold the unit upright with one hand and use the heat gun to loosen up the glue holding the digitizer to the unit. Run it along one edge for less than a minute until the glass is a little too hot to touch.
Quickly insert the razor as close to the glass as you can and about 6 centimeters in. Slide it along the side that you heated. Don't make any prying motions or you'll just crack the glass more.
Continue with the remaining three edges. Heat then separate. You may not make much progress the first time around, but by the second time, you should see the glass starting to peel away. It took me about 5 to 10 minutes per edge and it is grueling work.
Once you can safely peel the entire glass digitizer away from the unit, use the razor to lift up and peel off any of the flat black tape/glue that was left behind. Most of the unit where the glue goes is gray. On the sides there are two parts where you see black plastic. It is okay to leave glue residue as long as it isn't bunched up.
Vacuum up any stray glass slivers. Make sure you set aside tools screws and screw-hole-plugs before vacuuming.
Installing the new digitizer
Use an LCD spray and cleaning cloth to clean your LCD. Don't leave any dust or fingerprints as it will look bad once everything is put back together.
Remove the back covering of your replacement digitizer revealing the glue. Obviously, try not to touch the glue.
Align the digitizer above the unit, make sure the camera hole is on the correct side. Very slowly lower it down and try to have it perfectly in alignment when it touches. You will be able to nudge it a tiny bit, but the glue is strong and if you get it crooked, you are going to have to try to quickly lift it back up without cracking your new digitizer.
Once you have it in place, remove the front protective film and free the new cable. Wrap the cable around to the back and very gently insert it between the contacts then push the locking hinge down.
Testing and reassembly
Power it on and see if it works. Just push down the little metal bump closest to the edge where the power button would be on the frame.
When happy with the test, turn it off again and hold the unit above the frame.
Check the orientation then insert the top part first to fit the audio port into the hole. Line up the rest and then push down on all the edges to snap it into place.
Breathe a deep sigh of relief.
Appreciate the time you put into this, hopefully I never end up in a similar situation.
Could have used some more return key though lol
Sent from my Ceramic White LTE Galaxy Note using XDA Premium App
Wish I would have read this first. I broke the housing by the 2 bottom screws. Dayum! I haven't touched it since. Supposed to get the digitizer Friday. Wish me luck!
Its really easy to replace the digitiser on WiFi version. Use Stanley knife and hair dryer to loosen it off and remove middle flex cable. Videos on youtube
Sent from my GT-P7510 using xda app-developers app
Any picture of these 2 screws cause i do not see it on a p4 here.
I still have one here with a cracked glass but it all still works even the touch screen.
But i do not see the screw so a pic would be nice
Opuske said:
Any picture of these 2 screws cause i do not see it on a p4 here.
I still have one here with a cracked glass but it all still works even the touch screen.
But i do not see the screw so a pic would be nice
Click to expand...
Click to collapse
They are covered by plugs on either side of the charge port. Gotta pry the plugs out first.
Sent from my EVO using xda premium
Ok so i am on a mission this weekend then to try and do that then
Opuske said:
Ok so i am on a mission this weekend then to try and do that then
Click to expand...
Click to collapse
One tip: be really careful not to touch the inside surface of the glass. I ended up with a fingerprint on the inside that drives me nuts every time I clean the screen. Wear gloves if you've got them.
Otherwise it was no sweat. I used this as a guide but with a hair dryer instead of a heat gun.
https://www.youtube.com/watch?v=KUI2gDQbdDY&feature=youtube_gdata_player
Sent from my EVO using xda premium
Quick question
I really found this post very helpful, but I do have one question. What if when I was trying to pry the tab up to pull out the digitizer, I cracked the black plactic on the other side. Would this cause the new digitizer not to work when I finished replacing everything and put it back together?
Best tutorial on the web (much better than those godawful youtube videos).
Thank you!
Did u get an answer??? I need to
AylaAtreides said:
I really found this post very helpful, but I do have one question. What if when I was trying to pry the tab up to pull out the digitizer, I cracked the black plactic on the other side. Would this cause the new digitizer not to work when I finished replacing everything and put it back together?
Click to expand...
Click to collapse
Did you get an answer??? I did the same thing...
DEinspanjer said:
I smashed the screen on my Tab a few weeks back. While I didn't take a video of the replacement, here are some notes and tips on my experience:
[*]If the glass is cracked but you can still see the display fine (i.e. no rainbow or black ink spills) then it is just your digitizer that is broken. Your top priority at this point is to not break the LCD because the digitizer is relatively cheap (~$35 shipped from China, $60 from the US). This also goes for the picture being fine but the touch not working at all.
Click to expand...
Click to collapse
Just when I thought I knew the difference between the LCD and the digitizer I read your post. You said if the glass is cracked but you can see the display just fine the digitizer is broken. When you say "see the display fine" I presume when the device is on you can see whatever it should be showing? Correct me if I am wrong. Silly me I would have thought if the glass was cracked you need the LCD. Are the glass, LCD and digitizer 3 separate parts?
Anyway on my Note 10.1 2014 edition the display suddenly went black while I was using it. All indications are the device is working because I hear notifications if I sent email to one of the accounts registered on the device. Given this limited info which part(s) do I need. The glass is pristine in that there are no cracks or scratches. Do I need the digitizer, lcd or both? How can I determine what I need for sure?
Thanks in advance,
~metafizik
The digitizer is the touch sensitive glass, the LCD is under that and it makes the pictures.
If you crack or damage the LCD, you will frequently see something that looks like an ink spill or a rainbow pattern.
If you crack or damage the digitizer, you can still see pictures fine, but some or all of it might no longer respond to touch.
In your case, it sounds like your LCD is not working, but unfortunately it is hard to say whether that is the only part that stopped working since it wasn't due to damage to the screen.
DEinspanjer said:
The digitizer is the touch sensitive glass, the LCD is under that and it makes the pictures.
In your case, it sounds like your LCD is not working, but unfortunately it is hard to say whether that is the only part that stopped working since it wasn't due to damage to the screen.
Click to expand...
Click to collapse
Thank you for the information. I agree there is no telling what might have caused the problem especially given some other problems that proceeded this. I had recently replaced the battery and even with the new one it was draining way too quickly. I concluded it might be the ROM I was running had become corrupted because Google services was using the lions share of the battery instead of the screen. I downloaded and installed a factory Lolipop image and it was running fine for about half a day when the wife started playing around with live wallpapers we had never tried when it went black.
At this point I am reluctant to spend $ replacing the Lcd given it might be something else altogether.
Thanks again,
~metafizik
Accepting offers on my 32GB Note 10.1 2014 edition. As described above the display has gone dark but system is otherwise working fine. Includes very nice MoKo Wireless Bluetooth Keyboard Cover Case and the tablet's battery is new.
I seem to have small hairs under the screen protector, there's no bubble around it but it does go multicoloured , I also have small dots of dust too, any way to get rid of them, last screen protector , help!!!
Shower
TechMitchell said:
I seem to have small hairs under the screen protector, there's no bubble around it but it does go multicoloured , I also have small dots of dust too, any way to get rid of them, last screen protector , help!!!
Click to expand...
Click to collapse
Go into the bathroom,close the door and turn on a hot shower. once the room gets nice and steamy (give it some time) clean your screen with your micro fiber cloth. When you take the protective coating off of the back keep it as face down as possible so any remaining particles in the air do not stick to it ( the steam from the shower clears the dust from the air). Apply to your tab, work out the bubbles, ENJOY!
TechMitchell said:
I seem to have small hairs under the screen protector, there's no bubble around it but it does go multicoloured , I also have small dots of dust too, any way to get rid of them, last screen protector , help!!!
Click to expand...
Click to collapse
Put some tape around your finger (sticky side facing outwards). Lift up the screen protector carefully (perhaps in the washroom with hot water running, or another dustfree environment) and use your taped finger to tap the sticky side of the protector where the hairs/dust particles are (sort of like removing lint from clothing). I don't have long nor thin nails, so I used a razor blade to lift up my screen protector. Very carefully, though.
I would advise rolling up your sleeves, washing your hands, etc. so that the chance of dust re-entering the bottom side is minimized. I've done this many times and I just do it normally in my room without any special preparation, but it takes a very long time because every time I use the tape to remove a few dust particles, new ones get trapped under. Eventually, it's just a game of chance to see if I can remove all the dust particles without having any new ones >_>
Thanks
abmicyau said:
Put some tape around your finger (sticky side facing outwards). Lift up the screen protector carefully (perhaps in the washroom with hot water running, or another dustfree environment) and use your taped finger to tap the sticky side of the protector where the hairs/dust particles are (sort of like removing lint from clothing). I don't have long nor thin nails, so I used a razor blade to lift up my screen protector. Very carefully, though.
I would advise rolling up your sleeves, washing your hands, etc. so that the chance of dust re-entering the bottom side is minimized. I've done this many times and I just do it normally in my room without any special preparation, but it takes a very long time because every time I use the tape to remove a few dust particles, new ones get trapped under. Eventually, it's just a game of chance to see if I can remove all the dust particles without having any new ones >_>
Click to expand...
Click to collapse
Thanks, hope it works , tried the tape but there are some that just won't budge, oh well $20 down the drain. hope it works, it not , read above.
edit : removed the already applied protector with steamy shower running and used sticky tape to remove dust, went well, no dust particles under screen it now several areas sseem folded, as in that there's no way to use tape or pressure to get rid of it, too saccades to try to bend back, any ideas?
As a photographer, I especially apologize for the lack of photos of the process... this is a story of my S5 getting broken and repaired.
I left my S5 on the hood of my girlfriends Jeep while cleaning up the dog's feet and being distracted, I forgot to grab my phone. Driving down the canyon road 50mph back home, noticed something thunk off of the front of the car... yep it was my phone. It was in an Otterbox Defender series case.
Upon inspection, I was very impressed to find the phone in very good condition. The front glass totally unbroken with no scratches, the only visible damage was a scuff on the chrome of the top right corner and what looked like a tread mark from the tire. The otterbox case looked very good as well, it took some damage where the tire marks were on the upper right.
The phone's internal display took too much shock/flex and was shattered but still hard a partially visible image and the digitizer worked fine. I ordered a new display around $150, it came with a pre-installed homebutton/fingerprint scanner module. The display I ordered was pre-owned in a+ condition, so it had the old factory adhesives stuck to it.
I removed the small plastic cover on the rear to unplug the home-button cable, removed the old display using a heatgun to ease up the adhesive and it come off pretty smoothly (start at the top from the earpiece), you have plenty of room to get tools behind the screen to unplug the display's flex cable and pull the home-button's cable free.
I was impressed in how well adhered the glass is and how the home-button works, very waterproof design. The metal frame has a texture etched into it to promote even better adhesion.
-I carefully removed the old adhesive from the new display and from the frame. I used alcohol and microfiber rags and took my time, both parts come very clean with some fingernail force and patience. I applied the new adhesive, this part was very easy, the applicator-design the adhesive comes packaged in makes it a breeze to line up and entirely avoid wrinkles or mishaps. I'll link what adhesive I used, it seemed to be factory OEM and ridiculously sticky stuff, several times more powerful and pliable than the 3m strip-tape.
I made a double-check that the frame adhesion area was clean and began to hook the connectors back up, plugged the home button and LCD connector back in, I started applying the screen from the earpiece (earpiece metal fits through the hole in the glass to make lining up perfectly easy. and pressed the entire display into place. Bam, brand new. That adhesive WORKS perfectly. It grabs and holds, very tight. I feel very confident that the phone still carries its same waterproof spec.
I hope this helps any others with broken screens that want to bring their S5 back to life and to be unafraid to dig into this yourself.
Tips:
-You can likely use a hair dryer to heat up the old display when removing, feel it with your hands, don't get it so hot that you can't keep your fingers on it for a few seconds, you don't want to damage your earpiece, front sensors, camera, etc.
-When removing the old adhesive from a good-used display, use plastic to scrape at it, metal will remove the black dye and make scratched in the bezel around the screen.
-The capacitive sensors for Recents and Back have tabs that allow you to push them into the frame of the phone before applying the new screen, makes it much easier to align and worry-free.
The adhesive comes from Ebay seller diy_iparts "Pre-Cut Adhesive Tape for Samsung Galaxy S5"
(unsure if I'm allowed to post direct links to ebay) I am giving you this information because I read that a lot of pre-cut adhesives from other sources are bad quality and not up to OEM spec, made of totally different materials, etc. This won't matter too much if you aren't worried about the water resistance of your phone and the display sitting perfectly flush to the frame.
Hi.
I have cracked the rear battery glass cover again on my S8. Its the forth time it happens. And I don't know why.
I have bought genuine battery glass covers from ebay. But it doesn't hold long before the glass cracks again.
Does anyone know if there is an reinforced (maybe aluminium or carbon)?
(Sorry for my bad english)
try putting a skin on it. https://dbrand.com/shop/samsung-galaxy-s8-skins they look nice and should work like a screen protector on it.
Make sure you are taking off the foam part of the sticky part they put on it. The glass should fit flush against the back with the thin thin layer of adhesive they put. My mistake and I cracked the first one because it flexed.
@Class said:
Make sure you are taking off the foam part of the sticky part they put on it. The glass should fit flush against the back with the thin thin layer of adhesive they put. My mistake and I cracked the first one because it flexed.
Click to expand...
Click to collapse
What foam? I only took plastic of the adhesive tape that was already applied on the cover. Then placed the cover on the phone
This cover: https://www.ebay.com/itm/Genuine-Sa...271993&hash=item33d35abcf9:g:iZoAAOSwBEpZnZvO