I tried to root my phone with cf root, but then it turned off while flashing. Now i have my phone showing a small orange triangle in the middle and a phone on the left side and a computer on the right. I cant flash anything, it just gives me an error:
<ID:0/009> Added!!
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> Enter CS for MD5..
<ID:0/009> Check MD5.. Do not unplug the cable..
<ID:0/009> Please wait..
<ID:0/009> Checking MD5 finished Sucessfully..
<ID:0/009> Leave CS..
<ID:0/009> Enter CS for MD5..
<ID:0/009> Check MD5.. Do not unplug the cable..
<ID:0/009> Please wait..
<ID:0/009> Checking MD5 finished Sucessfully..
<ID:0/009> Leave CS..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> zImage
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Related
Hi there,
Please i need the help about the flashing with odin..
I have downloaded the firmware file but single and packed the is "S5360JPLA1_S5360OJPLA1_S5360XXLA2_HOME.tar.md5" and there is a SS_DL.dll aswell so when i put the file in to the pda button so there will be failed
Error:-
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5360JPLA1_S5360OJPLA1_S5360XXLA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sbl.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> BcmCP.img
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have problem about this please any one who know the answer please answer this...
Sorry for bad english
Thanks
zabeh said:
Hi there,
Please i need the help about the flashing with odin..
I have downloaded the firmware file but single and packed the is "S5360JPLA1_S5360OJPLA1_S5360XXLA2_HOME.tar.md5" and there is a SS_DL.dll aswell so when i put the file in to the pda button so there will be failed
Error:-
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5360JPLA1_S5360OJPLA1_S5360XXLA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sbl.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> BcmCP.img
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have problem about this please any one who know the answer please answer this...
Sorry for bad english
Thanks
Click to expand...
Click to collapse
Its bettr get d new firmwares having 3 files in it...... In android development section...
Go to android developments
Yea, you should just go to the Android developments and download the odin flashable firmwares by sir Doky.
Here's the link for it-http://forum.xda-developers.com/showthread.php?t=1465800
zabeh said:
Hi there,
Please i need the help about the flashing with odin..
I have downloaded the firmware file but single and packed the is "S5360JPLA1_S5360OJPLA1_S5360XXLA2_HOME.tar.md5" and there is a SS_DL.dll aswell so when i put the file in to the pda button so there will be failed
Error:-
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5360JPLA1_S5360OJPLA1_S5360XXLA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sbl.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> BcmCP.img
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have problem about this please any one who know the answer please answer this...
Sorry for bad english
Thanks
Click to expand...
Click to collapse
:what:Why you placed it in PDA? You should have placed it under One Package.:sly: So try again...:thumbup:
Sent Via XDA™ Premium
Hi, here is my problem..., for the last 4 weeks I have had no problems flashing ROMs but today all I'm getting is the following
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMG7_I9505EVRBMF5_I9505XXUBMG7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sbl2.mbn
<ID:0/009> NAND Write Start!!
<ID:0/009> sbl3.mbn
<ID:0/009> rpm.mbn
<ID:0/009> aboot.mbn
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is anyone able to help? :crying:
Seems to be okay but now stuck on SAMSUNG Logo
DHARQAXIAN said:
Hi, here is my problem..., for the last 4 weeks I have had no problems flashing ROMs but today all I'm getting is the following
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMG7_I9505EVRBMF5_I9505XXUBMG7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sbl2.mbn
<ID:0/009> NAND Write Start!!
<ID:0/009> sbl3.mbn
<ID:0/009> rpm.mbn
<ID:0/009> aboot.mbn
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Is anyone able to help? :crying:
Click to expand...
Click to collapse
Try flashing some latest version then the one u have let ut be any other region also
Also make sure no Kies programme is running in the background close tht or uninstall it Restart the pc ans dtry again
123hiten said:
Try flashing some latest version then the one u have let ut be any other region also
Also make sure no Kies programme is running in the background close tht or uninstall it Restart the pc ans dtry again
Click to expand...
Click to collapse
Thanks, I have removed Kies and flashed an old version of Philz and currently restoring a NAND :good:
35mins to restore my ROM DAYMMMNNN!!!!
i try to install custom rom on odin, and it failed, i dont know why, so i flash with G7102XXUANE2, and it stuck
here
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G7102XXUANE2_G7102OLBANE3_G7102DXUANC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl1.mbn
i wait for 1 hour
--------------------------------------------------------------------------------------
Fixed :3
hi guys i want to root my N900 with CF-Auto-Root-ha3g-ha3gxx-smn900 with Odin 3.07 but got error :
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-ha3g-ha3gxx-smn900.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> boot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cache.img
error was here
after this i restart my phone and get this error:
Firmware upgrade encountered
An issue.please select recovery mode in kies & try again
what should i do ?
I have a Galaxy Tab A 8" (SM-T380) which just received a security update (2019-11-30) and now it just constantly reboots -- gets to the logo screen and then just reboots again. Tried using the hardware reset (needle hole) and it didn't even recognize it. Tried holding the Power+VolUp button to get to the recovery screen and that initially displays the blue "Installing system update" screen for a split-second and then it shows a blue Error screen for a another split-second and then goes back to the reboot cycle again.
Looking for some recommendations. The balance of the post describes what I've tried but I found this page which describes applying a custom recovery. Is that my best next option?
I ran Odin3 and, while I couldn't get it into the recovery screen, I was successful getting it to the download screen. I downloaded the FW update (XAR-T380DXU3CSK1-20191125134039) from SamFRew. This page on using Odin said I only needed the AP file, so I selected the AP file and after the MD5 was confirmed clicked start but it failed (see below).
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img.lz4
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Further searching led to this page which says you always need to flash all four files. This FW download didn't include the CP (modem) file but I selected the BL, AP, and HOME_CSC and clicked Start again. It says it succeeded (see below) but it is still just back to the reboot cycle.
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> aboot.mbn.lz4
<ID:0/003> sbl1.mbn.lz4
<ID:0/003> rpm.mbn.lz4
<ID:0/003> tz.mbn.lz4
<ID:0/003> devcfg.mbn.lz4
<ID:0/003> cmnlib.mbn.lz4
<ID:0/003> keymaster.mbn.lz4
<ID:0/003> apdp.mbn.lz4
<ID:0/003> msadp.mbn.lz4
<ID:0/003> NON-HLOS.bin.lz4
<ID:0/003> lksecapp.mbn.lz4
<ID:0/003> sec.dat.lz4
<ID:0/003> boot.img.lz4
<ID:0/003> recovery.img.lz4
<ID:0/003> system.img.ext4.lz4
<ID:0/003> persist.img.ext4.lz4
<ID:0/003> userdata.img.ext4.lz4
<ID:0/003> modem.bin.lz4
<ID:0/003> adspso.bin.lz4
<ID:0/003> cache.img.ext4.lz4
<ID:0/003> Home Binary Download
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
AdvApp said:
I have a Galaxy Tab A 8" (SM-T380) which just received a security update (2019-11-30) and now it just constantly reboots -- gets to the logo screen and then just reboots again. Tried using the hardware reset (needle hole) and it didn't even recognize it. Tried holding the Power+VolUp button to get to the recovery screen and that initially displays the blue "Installing system update" screen for a split-second and then it shows a blue Error screen for a another split-second and then goes back to the reboot cycle again.
Looking for some recommendations. The balance of the post describes what I've tried but I found this page which describes applying a custom recovery. Is that my best next option?
I ran Odin3 and, while I couldn't get it into the recovery screen, I was successful getting it to the download screen. I downloaded the FW update (XAR-T380DXU3CSK1-20191125134039) from SamFRew. This page on using Odin said I only needed the AP file, so I selected the AP file and after the MD5 was confirmed clicked start but it failed (see below).
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img.lz4
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Further searching led to this page which says you always need to flash all four files. This FW download didn't include the CP (modem) file but I selected the BL, AP, and HOME_CSC and clicked Start again. It says it succeeded (see below) but it is still just back to the reboot cycle.
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> skip file list for home binary
<ID:0/003> aboot.mbn.lz4
<ID:0/003> sbl1.mbn.lz4
<ID:0/003> rpm.mbn.lz4
<ID:0/003> tz.mbn.lz4
<ID:0/003> devcfg.mbn.lz4
<ID:0/003> cmnlib.mbn.lz4
<ID:0/003> keymaster.mbn.lz4
<ID:0/003> apdp.mbn.lz4
<ID:0/003> msadp.mbn.lz4
<ID:0/003> NON-HLOS.bin.lz4
<ID:0/003> lksecapp.mbn.lz4
<ID:0/003> sec.dat.lz4
<ID:0/003> boot.img.lz4
<ID:0/003> recovery.img.lz4
<ID:0/003> system.img.ext4.lz4
<ID:0/003> persist.img.ext4.lz4
<ID:0/003> userdata.img.ext4.lz4
<ID:0/003> modem.bin.lz4
<ID:0/003> adspso.bin.lz4
<ID:0/003> cache.img.ext4.lz4
<ID:0/003> Home Binary Download
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Did you try flashing CSC not HOME_CSC? that will wipe your device which might bring you out of the bootloop.
I did not. I ended up sending it back to Samsung for repair.