Need Help ..Problem Solved.. - Legend General

When answering call and speaking phone screen goes black as it should..
Problem is that it don't come back when call is finished. Only thing to do is remove battery and restart.
Started doing this today
And now when ill start a call screen goes black and same thing nothing works only removing battery can reset phone : (
Can I remove that post.
Problem solved it started because i used protective sheet on screen and it got foggy when i cleaned it. From top right corner. And i think the sensor is there.
Anyway I removed the sheet and the problem solved
All the best
R

Related

Help! Stuck on Align Screen!

Guys, I hope you can help me!
I was using my Imate Jasjar when it was accidentally bumped by another person. the Jasjar fell but it wasn't that high and the floor was carpetted. However, I noticed that whenever i try to tap on the Start button on landscape mode, the calendar application opens up! And when I try to tap V-Bar on the other corner opposite the Start button, the Contacts application opens up. Basically, the soft keys on the bottom screen are the one opening up even if I'm tapping the ones on top! If I tap the bottom soft keys, I thought the Start button or my V-bar would come out but still the Calendar and Contacts applications were the ones that opened. Basically the everything on top cannot be tapped!
On Portrait mode, I can tap the start button but when the V-Bar was tapped it still opens the Contacts application.
I went to Settings then Screen to re-align the screen. I thought it would solve the problem but apparently it didn't! I was trapped in the Align Screen section giving me an endless loop to tap the 5 areas of the screen.
I now did a Hard Reset, and now I'm forever got stucked to the Align Screen part.
What am I supposed to do??? Please help!!!
Hi,
Seen the same problem... Try to guess the error margin of the alignment...
for example instead of tapping in the center of the cross try tapping on left or right... Since your screen isn't aligned you can't press on the center...
Now the problem is hardware, not the MB but the LCD...
After tou figure out the margin error, the Universal will resume and then you ca align the screen via Start->Settings->System, align screen
I'll try to know more about this problem asking my friend.
Best of luck
thanks for your reply!
i also believe that it has something to do with the LCD. there are no cracks whatsoever. problem with the aligning is i have to keep on guessing. and if ever i do align the screen successfully, i'm not sure if re-aligning the screen in Settings would solve the problem.
i would appreciate though if your friend or anybody else can shed light to a solution.
This is a simple problem to solve ;-)
When the allign screen is ON and you have to make the first tap on the crosshair (just before you start clicking away to allign your screen), twist your display from landscape to portrait mode...
Now continue to allign it as usual, and you should finish successfully!
Cheers,
San
unfortunately, after following your instructions, i still went on an endless loop on aligning the screen. i'll try to reflash the rom and see if it would work. i hope it does...
i updated my ROM. still stuck on the alignment screen!
any more ideas?
To be honest, sounds like your screen is broke. Even if you got it to align, I doubt it would be very usable. I think you are looking at repair - if there's no visible sign of damage, you might get away with a warranty repair.
Cheers,
Steve.
Hi
Few months back i've got exactly the same problems (odd LCD behavior, impossible alignment, etc...) with an HP4700. I went to the service center and they had to replace the LCD screen. They did not charge me and take it under warranty. In my case the unit did not drop and i made it clear to them. I would suggest you go back to the service center and forget about the drop in your problem description .
Cheers,
Bruno
I had the same thing happen on a HP 3700, I did not even drop it all i did was install the Quake game for it and after a few days the screen alignment went a bit out. It was usable but definately out by about 1 cm in each direction. The unit had not been dropped. I went into the allign screen utillity and ended up in the infinite loop. The only way to fix was a new screen. But unforunately it was no longer under warranty. The screen consists of 2 separate parts the lcd and the touch screen bit. In my case the lcd had no issues just the touch screen. Very annoying but there you go.
Search your soul and do what you feel comfortable with.
Good luck
Charlie
thanks for all your replies!
i've made several searches yesterday with similar problems (even if they're using different PPC models) and they all ended up sending back their units for repair. there's even one who posted in expansys with the same exact problem!
we'll be sending it back through expansys (we got the unit from them) and hopefully get it back before the end of the month. and yes, i won't tell them that it was dropped, he he :twisted: and they won't find evidence either on the outside because there are no physical damages. what a start of the new year for me <sigh>
right now i'm back using my XDA IIi.
thanks for all your support! this is my first thread/topic in this site and it's so unfortunate that it had to be sort of a negative one. looking forward to be active more here!
Hello there
This might help (I am currently wrking with 200 PDAs so have had this a few times)
THere may be a iece of dust/biscuit crumb etc, under the edge of the casing above the screen, try using a post it note or paper and go around the casing/edge of screen, this should clear the screen of anything that may be causing this problem.
THis worked for me on the majority of non-aligning screens
HTH
DB
My story was, one day when I needed to twist the screen, it was a bit stuck so I twisted a bit harder, yes it went back. Then few days later, the mis-alignment started and since then I have been keeping to do re-alignment my screen.
My screen is mis-aligned once every 2 or 3 days or even few minutes then I have to re-align by using WM5's alignment program. It sometimes takes me 2 or 3 times or even one time.
The most anoying thing is it keeps forget after aligned screen.
Now, certainty, I don't think it is a screen problem because after running alignment app, it correctly pointed into the right spot but then it forgot where the right position was.
I have done the upgraded ROM ( even tried Ivan AKU 3.2 ROM ) but problem still persisted.
I just tried clean up the edge of screen, finger cross, hope it fixes my problem.
Bad thing is, I bought my device from UK and I am living in Australia so therefore, my warranty is definately invalid. I don't want to spend 200 AUD for the new screen ( unless I am 100% sure that LCD is faulty ).
Anyone has any idea or even a better suggestion because I don't see many people having this problem.
I suspects that maybe the flex cable got ripped but not totally ripped. Don't know , please help me out on this one
Best regards
Anyone has any idea about my problem ??
One question :
I know that the flex cable has 2 connectors ( one is for LCD display and another is for LCD function ). Now does LCD function relate to the touch screen function ? and if one tiny wire of the function cable got cracked, but not totally cracked, will it affect the touch screen function ?
Other thing, does WM5 store any setting relating to screen alignment setting ? If yes, where is it ?
Thanks
Hi, from another forum, it only help to bypass the alignement loop:
"here you go theses are simple steps to bypass the touchscreen alignment.
Install you activesyn blah blah blah when it finds it go on my computer and go into your PDA device
go to windows startup and delete the Welcome file
after that give your PPC a soft reset and BAM u by passed the screen now get a free desktop program liek pocket controller from the internet it will automatically install on your pda and BAM you can control your pda add music and whatever
but now if you want to click stuff on the road get pen irazu just search on google and send it to your PDA then go to file explorer and double click it and you got a cute little mouse program that you can use like a stylus"
also try this little soft:
http://www.codefactory.es/downloads/mobile_speak_pocket/release/MSP_RemoteAlignment.zip
Hope it helps.
MaX
Hi godtakeit!
I've had the same problem a few weeks ago (and still having it from time to time) and for me a slight (very careful) bending of the screen makes it work again. It seems to me that there are connector behind or near the display which has some loose contacts.
Did you notice any other problems which came in conjuction with the alignment problem (e.g. speaker not working)?
.ox
Hi oxident
No, I don't have problem with speaker ( it was not working before but it is because of the jack plug problem - it solved ). Yeah, I did notice if I bend the screen carefully, the problem is gone. The funny thing is when I aligned the screen, it worked but if I closed it off and left it over night, it started again when I opened the lid.
You may right about the connector between LCD screen and mainboard. Well, I have no choice but openning the device and check it up.
Also, I read the thread somewhere in this forum and somebody advised this problem maybe relates to magnet around device. My brother aslo advised me that LCD charged and reserved negative electrons. Wierd but I am experiment it at the moment ( taking off battery and leave the device for a few days so that it can release the negative electrons ).
Hope it fixes
please help
i have an imate jas jam that i i got from my father he used it for like 3 years and it is pretty banged up so i cant use the warranty and repairs cost a lot, any who i got it yesterday and it was very slow so i reset the settings and now im stuck on the align screen it keeps going on for ever and ever if any one knows any thing plzzzz help
Welcome aboard
You have one of the best HTC devices ever made!
Have a look here to locate the solution to your prob:
http://forum.xda-developers.com/showthread.php?t=549207
Post number 2
Good luck,

S100 keeps hard reseting

Hi,
My S100 keeps hard reseting. It was working ok, until last week. Since then, it has hard reset 3 times now.
It happens randomly. I've formatted the SD card as well, in case the issue was card related. I don't know what to do...
R 1.12.00
G 1337.42
D 1.12.120 WWE
Could it have anything to do with my backup battery?
I've noticed that I have no issues if it's connected to the power, but if my battery gets to half capacity, it's when my problems begin...
ALL help is welcome....
Hi got same problem ...unfortunately while using tomtom so i lose myself somewhere in between Austria,Switzerland and Germany....
so it reset many times even while phisically resetted...it didn't start any more for 10 min and then it starts properly...and again and again.....
noticed low internal battery....will change it (if i found the user manual) and i'll let You know the progress...
....small reply...i check in the User Manual but no idea on how to change and which is the internal backup battery....any suggestion ? ? ?...pls ?
up.........thnks
uh...well i have the same problem and i know why it happens...
It's just that the back cover has a small plastic notch at the bottom right side which must touch and push a small switch located at the bottom right (the switch is located just above the red plastic thing).
Since my back cover has a side plastic notch that is broken, sometimes the back cover gets a little bit loose, forcing the bottom switch notch to release that switch which in turn forces the ppc to sometimes reboot/hard reset.
Check if your back cover is Okey.
Keeper
Keeper said:
uh...well i have the same problem and i know why it happens...
It's just that the back cover has a small plastic notch at the bottom right side which must touch and push a small switch located at the bottom right (the switch is located just above the red plastic thing).
Since my back cover has a side plastic notch that is broken, sometimes the back cover gets a little bit loose, forcing the bottom switch notch to release that switch which in turn forces the ppc to sometimes reboot/hard reset.
Check if your back cover is Okey.
Keeper
Click to expand...
Click to collapse
WOAH...got it....(i'll keep testing tomorrw while running somewhere in France....) is enough to force it with a ...."piece-of-something" placed there in case? or there are some other indications on "how to"??.....
say thanks anyway is always not enought......
yes...you can use whatever you like...(you can even glue it)
Honestely i don't know what was HTCs ideia of putting that dumb switch in there...
Regards,
Keeper
Yeah, that switch is pretty dumb and a waste of money. None of my newer HTC phones have that switch. I guess in more recent phones they realized it was a waste.
The switch was there for a good reason
Hi! The switch is there to turn off the phone when you open the battery cover. Remember, WM 2003 is based on volatile memory, so if the power goes out, all of your data gets deleted and the OS has to reload from flash rom. Anyway, to my understanding the switch has to do with not using the backup battery without the actual battery in there as the backup battery is strong enough to power the volatile memory but not the entire device. The solution I chose for my device is a piece of clear plastic tape running along the crack between the battery door and the camera housing. I attached the tape to the sides as well, and made sure to use the stylus to push the tape down between the grooves on the sides. Otherwise dust would get in right away and weaken the bond blah blah blah.
Summary: Tape on the battery cover, the switch was a good thing. All devices since MDA Compact run WM5, which is non-volatile memory based and is always stored no matter what.
Hi guys,
At first I decided to open up my Magician, to look for that "backup" battery.
Didn't find any.
Turns out, my hard reset problem is caused by my phone battery. The regular battery is wasted. So wasted that the phone cant hold the backup. I found it weird that the phone wouldn't hard reset if was kept on power. As soon as i unplugged it, it went bye bye.
I managed to test it with a battery from a friend, and as soon as he used my battery on his phone, the backup warning come up.
I don't wanna say that, in some cases, the back lid won't cause this problem.
In my case, thankfully I managed to sort out where the problem was.
Thanks!
It keeps hard resetting
Hi Guys,
i've tried all the above written tips and tricks; but, my magician still have the same problem, every time i removes my battery it goes hard reset and again i've to start from the scratch - align screen - then it installs the applications again and back to the square one.
previously it was ok and after a year and half of using it started going soft reset now and then itself - i gave it to a local services center, they said that it has a loose contact to the battery that's why it gets soft reset, so i got my battery connector replaced. it solved the soft reset problem, but now the bigger problem has come up - it goes hard reset every time i remove my battery.
one thing i've noticed - it never hard resets when i keep it connected with my charger or usb cable
any one has any idea why its happening...
well i would suggest that your backup battery is dead...
Keeper
that i've checked keeper it always shows 100%.
and all the time since i bought this i've never seen that thing moving from 100%,
ok just tell me is it possible to replace the backup battery?
Well, i doubt it...all this stuff is really small...honestely i don't even know where is the backup located at, in the pcb... (photo of the pcb is in here: http://forum.xda-developers.com/files/naked-magician-insane.jpg)
I would suggest that you should go to a repair center and ask them for a repair cost budget...that way you'll be informed what exactly is wrong with your pda...
Keeper
webshocker, if you want to try and replace your backup battery, check the photo in attachment that i've made...
It seems that it ain't that hard to replace it...
Regards,
Keeper

Black screen with date and time in GALAXY S4

Hello all
Today I started experiencing a problem with my SAMSUNG GALAXY S4 GT-I9505.
I must say first that I did not do anything to him today or any other day in the whole month I he is at my reach.
Today when I took the phone from my pocket to see something I saw there's a black screen with time and date and the signs of battery and reception with no availability to do anything with him.
I took off the battery and it came back to normal but then again turned to that screen. I made a factory reset through the settings and it seemed to help for a few hours but then it came back. Now I'm with that black screen and can't do anything.
I must say that sometimes the black screen goes off and my original screen comes back but it comes back.
I disabled all the sensors and the option in Settings which refers to S View Cover (I understood from googling it that this screen shows up when I have S View Cover - which I don't have! )
What should I do? This phone is a new phone - I had it only for a month (and a bit more)!!!
PLEASE HELP ME
I DIDN'T DO ANYTHING TO HIM
Edit: Here's a photo of the screen
http://www.siz.co.il/codes.php?i=nytta3wezhmz.png
Check any magnetic things near when this happened
niketkumar said:
Check any magnetic things near when this happened
Click to expand...
Click to collapse
Nothing magnetic. It happened when I took it from my pocket and in that pocket I had only my wallet made of leather closed (no coins or credit cards popping out).
Please help!

New Note 3 screeen showing unusual behaviour

7 days ago I have purchased this new note 3 N900 , the screen today is acting in a weird manner.
Here is what happened, I switched on the phone and then there was only the wallpaper and a dark triangle on the right side of the screen, I rotated screens but the thing remained the same, that is only the background with a dark triangle on the right side of the screen with a little flicker so I had to restart the phone.
Now it's working fine, please suggest should I get this phone replaced, is this some kind of hardware issue.
Also I had purchased a cover for the phone which was actually very hard to remove and I applied a lot of strength on the right side of the screen to get the cover removed, can that have caused the problem.
Also is there any app which I can use to check is there is a problem with the screen or not.
Thank you for your time, please give your valuable suggestion.
I'm running stock android 5.0 the same software that came out of the box.
The screen roughly looked like the image attached below -
Forgot to mention above that earlier I also had this issue where the all apps button on main screen turned to blue while everything was working fine and won't change to normal so I had to restart the phone again in that situation which did fixed that problem.
Would it be possible for someone to clarify that is this some kind of problem cause due to applying excess pressure as the Urban Armor Case I have purchases was really really hard to remove so I had to apply a lot of strength on the right side of the screen, it was so hard to remove that even the official back cover came off with it, can that have caused the issue or is it just a software problem.
Sent from my SM-N900 using Tapatalk

Half of the screen is black

Hello !
The bottom of my screen is completly black but the touchscreen is still working.
I went running with my phone in my hand and the weather was vert cold. At first the bottom half of my screen was flickering/grey and then it went completly black
What I already try to solve the issue :
- install TWRP and wipe everything
- disconnect the battery from the phone
Any thoughts ? How could I know if it comes from the motherboard or the screen?
Water droplets must of have got into the motherboard. Unfortunately you can't fix a hardware issue through twrp. I would recommend replacing the motherboard. Good luck

Categories

Resources