Related
Hi all.
Surely this isnt right. Had my Nexus-One 5/6 weeks i dont remember whenever they were released and shipped to the UK.
After 2 weeks i Rooted the phone, and installed the CyanogenMod.
Now i noticing today battery was stuck on 98% charging. Checked in Menu>Spare Parts>Battery Information.
Battery status: Full
Power plug: USB
Battery level: 98
Battery scale: 100
Battery health: Good
Battery voltage: 4045 mV
Battery temp: 29.5C
Battery technology: Li-Ion
Now since sending a few SMS, ans opening a Email, the level is now at 92%. Yet its still plugged in but the battery is draining! WTF is going on.
The phone has always and only been charged using USB!
I charge the phone once daily overnight while i sleep.
Surely something is wrong here?
nyzrox said:
Hi all.
Surely this isnt right. Had my Nexus-One 5/6 weeks i dont remember whenever they were released and shipped to the UK.
After 2 weeks i Rooted the phone, and installed the CyanogenMod.
Now i noticing today battery was stuck on 98% charging. Checked in Menu>Spare Parts>Battery Information.
Battery status: Full
Power plug: USB
Battery level: 98
Battery scale: 100
Battery health: Good
Battery voltage: 4045 mV
Battery temp: 29.5C
Battery technology: Li-Ion
Now since sending a few SMS, ans opening a Email, the level is now at 92%. Yet its still plugged in but the battery is draining! WTF is going on.
The phone has always and only been charged using USB!
I charge the phone once daily overnight while i sleep.
Surely something is wrong here?
Click to expand...
Click to collapse
cyan 5.0.3.1 drained the F outta my bat as well. I went back to 5.0.2 back to normal
nyzrox said:
Hi all.
After 2 weeks i Rooted the phone, and installed the CyanogenMod.
Now i noticing today battery was stuck on 98% charging.
[... deleted ...]
Surely something is wrong here?
Click to expand...
Click to collapse
Nope. Cyanogen 5.0.3+ uses a new kernel which implements different charging logic.
Basically it will charge to 100% but then stop charging until the battery drops to 90%. It supposedly improves battery life by avoiding overcharging.
FYI to the OP... charging exclusively from USB is not going to help your battery in any way, contrary to what a few people on this forum think. Use the stock charger and save yourself the time.
meric04 said:
Nope. Cyanogen 5.0.3+ uses a new kernel which implements different charging logic.
Basically it will charge to 100% but then stop charging until the battery drops to 90%. It supposedly improves battery life by avoiding overcharging.
Click to expand...
Click to collapse
This. Supposedly this will lead to longer battery life without a degradation in capacity due to excessive charging. This has been implemented with software logic for Li-Ion batteries in Laptops for a while now (although it doesn't appear to be default on most). You'll see it charge again once it hits 90%.
Is it just me or everyone else that is experiencing a super long time in charging their phone to full battery? I am running the froyostone latest build and I have already followed all the guides in this forum to save battery life. The issue I am having is that it takes many hours to recharge the battery to full when connected to a wall charger.
It took 5 hours to go from 30% battery to 90%.
*no i wasn't charging the phone with the phone turn off*
Zythyr said:
Is it just me or everyone else that is experiencing a super long time in charging their phone to full battery? I am running the froyostone latest build and I have already followed all the guides in this forum to save battery life. The issue I am having is that it takes many hours to recharge the battery to full when connected to a wall charger.
It took 5 hours to go from 30% battery to 90%.
*no i wasn't charging the phone with the phone turn off*
Click to expand...
Click to collapse
I have a stock battery, which I can charge from 25% or less to 100% in about 30 minutes to an hour. I think there is something wrong with your charger.
its actually not taking that long, it probably got to 90% VERY quickly, you just checked on it later... they're false numbers... what you need to do is this; run your battery all the way down.. then charge it for about 1-2hrs, until it gets somewhere in the 90's then, while plugged in, shut the phone down, remove the battery, put the battery back in, boot up the phone (the phone should remain plugged in) then load up WM, load up android with the hard buttons backlight on, then once it boots you should show higher than what you had before (if not 100%) from this point android will remember your charge and you will be able to go to 100% all the time now. (until you load a new rom)
10507 said:
I have a stock battery, which I can charge from 25% or less to 100% in about 30 minutes to an hour. I think there is something wrong with your charger.
Click to expand...
Click to collapse
I got stock battery also. No idea why it taking so long.
javolin13 said:
its actually not taking that long, it probably got to 90% VERY quickly, you just checked on it later... they're false numbers... what you need to do is this; run your battery all the way down.. then charge it for about 1-2hrs, until it gets somewhere in the 90's then, while plugged in, shut the phone down, remove the battery, put the battery back in, boot up the phone (the phone should remain plugged in) then load up WM, load up android with the hard buttons backlight on, then once it boots you should show higher than what you had before (if not 100%) from this point android will remember your charge and you will be able to go to 100% all the time now. (until you load a new rom)
Click to expand...
Click to collapse
I have already tried this but still no luck.
10507 said:
I have a stock battery, which I can charge from 25% or less to 100% in about 30 minutes to an hour. I think there is something wrong with your charger.
Click to expand...
Click to collapse
What kernel are you using?
Sichroteph said:
What kernel are you using?
Click to expand...
Click to collapse
I am using hastarin r8 kernel, but I was experiencing the same issue with previous versions and the default kernel.
I just tested the charging rate by connecting my HD2 to a stock charger from HTC which I borrowed from a friend. Charging was a lot faster.
Since I bought my HD2 used, the charger that came with it, is not the stock charger from HTC.
But I still don't understand what is causing the charging to be very slow.
How to calculate charging time
Charging time = capacity of battery x 1,4 / charging current
HD2 stock battery= 1230mAh x 1,4 / 1000mA = 1,7 hours
Best
leehobin
Two things on charging batteries:
1) First, make sure none of the pins in the battery compartment is bent. This dramatically slowed charging for me once.
2) Android keeps battery stats in a file that gets loaded with your build. THese stats are often wrong. Be sure to fully charge under WinMo, then with power still attached, boot into Android. This will adjust some of the stats and charging in Android should be fine then. There's a thread somewhere on more details here if you want to tweak your stats. The battery slows down its charging when it gets close to the full state. If for some reason your charger thinks the temperature is getting too high or the state is getting near full it dramatically slows the charging rate. Both of these could be erroneous interpretations of the battery data. Also, if you have an extended battery, make sure to use a Kernel that is compatible with extended batteries, like Hastarin 7.x.
Zythyr said:
I just tested the charging rate by connecting my HD2 to a stock charger from HTC which I borrowed from a friend. Charging was a lot faster.
Since I bought my HD2 used, the charger that came with it, is not the stock charger from HTC.
But I still don't understand what is causing the charging to be very slow.
Click to expand...
Click to collapse
Not all chargers are built the same. Some usb charger provide more juice while others provide less. Maybe your non stock charger came from a non smart phone...
Zythyr said:
Is it just me or everyone else that is experiencing a super long time in charging their phone to full battery? I am running the froyostone latest build and I have already followed all the guides in this forum to save battery life. The issue I am having is that it takes many hours to recharge the battery to full when connected to a wall charger.
It took 5 hours to go from 30% battery to 90%.
*no i wasn't charging the phone with the phone turn off*
Click to expand...
Click to collapse
Current Widget from the Market can tell you how many mA your phone is getting when it's charging.
this is just an approximation formula. a lithium ion battery charger is more sophisticated than this. it first brings battery voltage up to 20% safely (because any voltage below this is the harmful zone of operation), then it stuffs the battery at full capacity upto 80%. then in the 3rd stage, the current drops linearly with time.
over the past year, my stock battery gives me the following profile:
20-80% -> 1 hour (800-820ma constant, unless phone is awake)
80-100% -> 1 hour (800 -> 0ma)
by 100% i mean 0ma charge current. not 100% on the battery icon. you should be aware that the battery is still charging even after the indicator reaches 100%. but the current is insignificant (10-20ma)
even though the charger is rated at 5v 1A, it supplies only 820ma current at the maximum. this is normal. also for a lion battery the safe operating regions are around 20-90%. by safe i mean prolonging battery life. this roughly corresponds to 3.6v - 4.0v. avoid overcharging your battery frequently.
also someone mentioned current widget as a good approximate tool to study battery performance. you might also want to delete batterystats.bin and condition your battery once (i.e. fully discharge and fully recharge). this will force android to re-determine the new 0% and 100% levels. search the android forums for this.
hope this helps.
leehobin said:
Charging time = capacity of battery x 1,4 / charging current
HD2 stock battery= 1230mAh x 1,4 / 1000mA = 1,7 hours
Best
leehobin
Click to expand...
Click to collapse
silenced3 said:
this is just an approximation formula. a lithium ion battery charger is more sophisticated than this. it first brings battery voltage up to 20% safely (because any voltage below this is the harmful zone of operation), then it stuffs the battery at full capacity upto 80%. then in the 3rd stage, the current drops linearly with time.
over the past year, my stock battery gives me the following profile:
20-80% -> 1 hour (800-820ma constant, unless phone is awake)
80-100% -> 1 hour (800 -> 0ma)
by 100% i mean 0ma charge current. not 100% on the battery icon. you should be aware that the battery is still charging even after the indicator reaches 100%. but the current is insignificant (10-20ma)
even though the charger is rated at 5v 1A, it supplies only 820ma current at the maximum. this is normal. also for a lion battery the safe operating regions are around 20-90%. by safe i mean prolonging battery life. this roughly corresponds to 3.6v - 4.0v. avoid overcharging your battery frequently.
also someone mentioned current widget as a good approximate tool to study battery performance. you might also want to delete batterystats.bin and condition your battery once (i.e. fully discharge and fully recharge). this will force android to re-determine the new 0% and 100% levels. search the android forums for this.
hope this helps.
Click to expand...
Click to collapse
wow ! thanks alot !
Is it bad to let my charge over night overnight? I thought it would stop charging when it got full to avoid overhanging.
Sent from my HTC Inspire 4G
Since I have access to a a battery simulator and charger... the best way to recondition a battery is:
1. Create a low battery scenario by lowering the input voltage to just a hair above 2.7 volts (I had to create a shim to get to the battery receiver leads).
2. Boot with full 4.2 and in ClockWork remove battery stats
3. Drain and Charge battery to 4.2
I get enterprise email and I get a lot of mail daily that I have to read and respond to (150 or more -- no I don't respond to all of them), plus the phone calls, RSS reading and some texting plus a pic here and there and maybe a couple of you tube videos. I get more than 24 hours until the 15 % comes up. 50 hours would be nice but that did not even happen in my black berry with Edge only.
Mine improve 3 fold from sub 7 hours to 24 plus (yes I sleep late so probably the phone gets a 6 hour rest but the enterprise email and text is pushed down even then as I work with folks from Asia and Europe as well.
logdrum1 said:
Since I have access to a a battery simulator and charger... the best way to recondition a battery is:
1. Create a low battery scenario by lowering the input voltage to just a hair above 2.7 volts (I had to create a shim to get to the battery receiver leads).
2. Boot with full 4.2 and in ClockWork remove battery stats
3. Drain and Charge battery to 4.2
I get enterprise email and I get a lot of mail daily that I have to read and respond to (150 or more -- no I don't respond to all of them), plus the phone calls, RSS reading and some texting plus a pic here and there and maybe a couple of you tube videos. I get more than 24 hours until the 15 % comes up. 50 hours would be nice but that did not even happen in my black berry with Edge only.
Mine improve 3 fold from sub 7 hours to 24 plus (yes I sleep late so probably the phone gets a 6 hour rest but the enterprise email and text is pushed down even then as I work with folks from Asia and Europe as well.
Click to expand...
Click to collapse
How do I create a low battery scenario by lowering the input voltage to just a hair above 2.7 volts?
hiltun said:
Is it bad to let my charge over night overnight? I thought it would stop charging when it got full to avoid overhanging.
Sent from my HTC Inspire 4G
Click to expand...
Click to collapse
Yes, the "charger" that you plug into the wall is just a power supply, the actual "charger" is in the phone, and when it detects the battery is full it stops charging.
Hi all,
I bought a new battery for my HD2 which has 3.400 mAh. Unfortunately the HD2 does not seem to notice the higher capacity.
Battery.exe from htc testing tools shows "FULL (mAh): 12296". As all values are times 10 (like 786% battery right now) I read this as 1230 mAh battery capacity the device thinks to have.
How would I recalibrate the device so it recognizes the new battery capacity?
Thank you, Franky
P.S. I tried to search but found nothing I had'nt already tried. Most people suggest something like this:
1. discharge fully until the phone shuts down by itself
2. remove battery and wait ~1 minute
repeat 1) and 2) until the device shuts off within minutes after being switched on
3. charge completely with the phone OFF until the green light is lit
4. remove battery and wait ~2 minutes
which I tried at least 5 times. I even bought an external charger so the battery is 100% full when put into the device.
Is it a genuine battery, bought from a reputable dealer? I bought a ' genuine' battery from an Amazon seller which was a bad fake, got very hot and only have half the capacity it should have.
If you are using battery in WinMo then I thought there was little to do, in Android there are several tricks but essentially charging with the phone off should give you a full charge.
Have you tried using the phone until it switches off? It might be that you have the extra life but your software doesn't recognize it.
Thanks for your reply!
boomboomer said:
Is it a genuine battery, bought from a reputable dealer?
Click to expand...
Click to collapse
Dunno. All dealers pretend to be (the only) serios. But it's a German dealer /w good ebay ratings.
boomboomer said:
Have you tried using the phone until it switches off? It might be that you have the extra life but your software doesn't recognize it.
Click to expand...
Click to collapse
That's the issue. When the phone shuts down (unfortunately it does that silently, not like a Nokia) and I remove the battery (wait some time) and re-insert it it is at 50% and lasts a few hours more (BTW: doesn't work a 3rd time).
How to tell the software/phone it got a better battery?
BTW: It's WinMo 6.5.5
Thanks, Franky
The phone should only shut down when the battery reaches a certain voltage, or the battery shuts itself off to protect the cell. It sounds like your phone is working properly by turning off due to low voltage, but then when the voltage rises (when you rest it) restarting. The battery protector circuit would not allow it to start for a second time.
You can try using battclock to check your voltage, which should be 4.206 when fully charged and down to around 3.2 or 3.6 when empty. But I think you have a fake battery that simply will not contain that much power - it is a double thickness one, with a bulging battery cover required?
Hi boomboomer,
private talk, he?
Yeah, the battery is a double thick one with extra cover.
Battery.exe showed these values when I got 1% battery left:
MS percentage: 1%
PA percentage: 1%
ACR (mAh): 83 (i.e. 8 mAh)
1st dis_ percentage: 150%
V_MBAT (V): 3.742
after removing the battery and setting it in again after 5 minutes I got these values:
MS percentage: 47%
PA percentage: 47%
ACR (mAh): 5776 (i.e. 578 mAh)
1st dis_ percentage: 470%
V_MBAT (V): 3.747
Regards, Franky
If you notice the voltage reading stays the same for both instances, 3.742 V which isn't far off shut down value for the phone. What is changing is the current value, which if the voltage is constant means the battery resistance is dropping after you rest the battery for 5 mins, or letting the cell cool down and hence giving the impression that the cell still has 47% capacity - which it does not.
A high internal cell resistance means high temperatures and a very short life span, a genuine battery should have a fairly constant resistance and hence linear discharge.
Bottom line is your ebay seller did not send you a battery capable of providing 3400mAh, it may also not be safe to use in your phone in certain conditions e.g. a hot sunny day on your car dash may result in a breach of the cell membrane and even a lithium fire.
I would advise returning the battery for a refund and spend a little more for a genuine HTC extended battery from someone you trust.
Well, besides that I cannot send it back (it's dearer than to dump it) the battery shurely has more than 1230 mAh. From what I saw its somewhat about 1800 mAh (1230 + 50% battery left when re-inserting).
Only the HD2 does not recognize it.
Regards, Franky
Going to get my Arc on Monday, but I have some concerns about battery life
I see it uses LiPol battery - I searched through multiple formus, but I couldn't find proper advice :
- how to charge/format LiPol battery to get most out of it ?
Should I charge it for 8 hours first 4-5 cycles, or how to format LiPol ?
For Li-Polymor, just charge till full. But make sure to charge it before it falls below 10% - 20%. Charge it often (daily) for the first week. I find that doing so, improve the battery's hold on a charge.
Sony Ericsson's batteries are already charged and ready to be used.. so no need to do 8 hours first, but as darkmax1974 said, keep charging it regularly and don't let it go below 10%
amen. letting it die completely has a negative effect on the longevity
ok, I won't charge it for 12hrs for the first time, like I used to do with new phones
Is this the definitive way to do it?
http://hemorrdroids.net/battery-calibration/
Those steps came from here, xda devs.
1. Run the device down until it turns itself off.
2. Turn it back on and wait for it to turn itself off again.
3. Remove the battery for 10 seconds.
4. Replace the battery, but leave the device off.
5. Charge the device until full and then for another hour.
6 **Root users only** Using a Terminal Emulator, type “su” enter, followed by “rm /data/system/batterystats.bin”
7. Run the device’s battery down until it turns itself off.
8 .Turn the device on and charge for at least 8 hours.
9. Unplug the device, turn off, then charge for another hour.
10. Unplug the device, turn on, wait 2 minutes.
11.Turn off again and charge for another hour.
12. Restart and use as normal.
Quite a performance! Does it preserve battery lifespan, or is it more to do with slowing down battery drain and does it really work?
He mentions 2 interesting things:
"Generally charge them before they get lower than 50%". I didn't know that, so it's actually better to charge more often and not let it drain down?
"USB charging is actually better for the battery and you may get up to 1 hours more standby time." So you gain an hour standby but it takes twice as long to charge the phone.
Nice manual
Will try it
Sent from my GT-I9100 using Tapatalk
Some will say that its complete nonsense .
Overcharge for 8 hours ??? how does the battery not turn charging off at 100%
Recharge 50% the accepted figure is not to go below 20% to often .
They may be right or wrong their are so many contrasting views on battery charging .
jje
Discharging battery and then reloading it fully, it's the normal procedure for battery calibration for almost all the devices in the world (including computers, etc.).
Step 8 to 11 seems quite a bit strange however.
hm, just seen a different way to calibrate the battery. basically, you drain the battery, take it out for a couple of minutes, put back in, then try to turn it on to make sure it's completely flat.
then you charge it fully, then boot to recovery and wipe battery stats then drain and fully charge. so... which one is more likely to be the better?
that guy also advises to repeat that 12 step, 1-2 day long tedious procedure "every month or so".
it is lunacy honestly speaking
does it work? did he died ?
LOL I dont understand .... I just read in another day that NEVER LET BATTERY GO LOWER THAN 15% and know I read "drain drain drain" Oh welll ...
I also thought that at 100% the charging process stops.
Although this thread is about battery calibration, these questions about battery charging always pop up.
Battery calibration is the process by which you set your device with your battery data.
Every single battery is slightly different. Although there are minimum stantards to every spec of the battery, each battery is different.
Calibrating your battery is nothing more than setting your phone to the real specs of your own battery (since the phone comes configured with the battery factory standards). For example, your phone may be set to use a battery which maximum charge is 1650 mAh, but your battery has a maximum charge of 1625 mAh. That may be within the acceptable factory standard, meaning you have a normal battery, but that also means that your phone will never indicate a 100% charge after you unplug the charger.
If you calibrate that hypothetical battery, you will "tell" your phone that its maximum charge capacity is actually 1625 mAh, meaning from that on your phone's battery indicator will be more accurate.
For that reason, it is necessary to fully discharge and fully recharge your battery for the calibration process, since your device must read the actual specs (minimum charge, maximum charge, charging current, etc) of the installed battery.
I don't know about how many times this full cicle (discharging and recharging) must be performed, but that is the reason why it must be performed for the calibration to succed.
A DIFFERENT THING is the normal discharging and charging process during normal use of the phone.
In this case, you should NEVER let your battery go under 20% and, what few people know, it also should never go over 95%. This stresses the battery and diminish its life time.
Also, and there's a lot of doubts about this, the lower the charging voltage, the slower the charging process, but the longer the battery life.
High charging voltages (like the one used by the charger sold with the phone, which is around 5V) stress the battery, diminishing considerably its life time.
That is true for all lithium-ion batteries!
Therefore it is better to charge your phone through USB (which uses around 4,3V) than to do it using the charger provided with the phone.
You may be asking "If the charging voltage of the charger provided by the manufacturer stresses the battery, why does the manufacturer provide such charger?"
For purely commercial reasons! Higher voltages mean shorter charging cycles, which please the consummer. Moreover, the battery capacity loss with the factory provided charger is around 15-20% a year (considering "normal" to "heavy" use). That is to say that after a year your battery will only reach 80-85% of the maximum charge it used to reach when it was new. And by that time your manufacturer expects you to consider buying a new phone, with more features.
Summing it up:
- calibration is just the process by which you "tell" your phone what the real specs of your battery;
- in normal use, charging your phone through USB is better than doing it with the manufacturer provided charger;
- try not to let your battery charge go under 20% nor above 95%;
- if you're interested, read more about it at batteryuniversity.com
Spin three times in clockwise direction with left middle finger on your nose while blinking your eyes with the phone plugged in.
Jump in the air 3 times.
Unplug phone.
Thats some messed up instructions.
Do you have any idea what kind of strain you're putting on the battery while doing all that?
All you're gonna get is some extra minutes, maybe an hour but is it really worth it because you're just reducing overall battery lifespan by doing that procedure over and over.
Specially when you constantly keep the battery at 4200mV (full charge) for a long time. You're practically killing it by overcharging.
Transmitted from a Galaxy far far away via XDA telepathy.
m2smoe said:
Spin three times in clockwise direction with left middle finger on your nose while blinking your eyes with the phone plugged in.
Jump in the air 3 times.
Unplug phone.
Click to expand...
Click to collapse
that made me chuckle
Never done a calibration on a battery and most of the time i even didn't let battery to discarge very much and then load it again. Never had a problem with battery life it last how long it should last every time and i've used that battery for years. So the battery "calibration" are kinda useless.
Matriak31 said:
that made me chuckle
Click to expand...
Click to collapse
Well then, my job here is done
m2smoe said:
Well then, my job here is done
Click to expand...
Click to collapse
it is indeed...i should follow you just to have more laughs like that cheers
RenatoN said:
Although this thread is about battery calibration, these questions about battery charging always pop up.
Battery calibration is the process by which you set your device with your battery data.
Every single battery is slightly different. Although there are minimum stantards to every spec of the battery, each battery is different.
Calibrating your battery is nothing more than setting your phone to the real specs of your own battery (since the phone comes configured with the battery factory standards). For example, your phone may be set to use a battery which maximum charge is 1650 mAh, but your battery has a maximum charge of 1625 mAh. That may be within the acceptable factory standard, meaning you have a normal battery, but that also means that your phone will never indicate a 100% charge after you unplug the charger.
If you calibrate that hypothetical battery, you will "tell" your phone that its maximum charge capacity is actually 1625 mAh, meaning from that on your phone's battery indicator will be more accurate.
For that reason, it is necessary to fully discharge and fully recharge your battery for the calibration process, since your device must read the actual specs (minimum charge, maximum charge, charging current, etc) of the installed battery.
I don't know about how many times this full cicle (discharging and recharging) must be performed, but that is the reason why it must be performed for the calibration to succed.
A DIFFERENT THING is the normal discharging and charging process during normal use of the phone.
In this case, you should NEVER let your battery go under 20% and, what few people know, it also should never go over 95%. This stresses the battery and diminish its life time.
Also, and there's a lot of doubts about this, the lower the charging voltage, the slower the charging process, but the longer the battery life.
High charging voltages (like the one used by the charger sold with the phone, which is around 5V) stress the battery, diminishing considerably its life time.
That is true for all lithium-ion batteries!
Therefore it is better to charge your phone through USB (which uses around 4,3V) than to do it using the charger provided with the phone.
You may be asking "If the charging voltage of the charger provided by the manufacturer stresses the battery, why does the manufacturer provide such charger?"
For purely commercial reasons! Higher voltages mean shorter charging cycles, which please the consummer. Moreover, the battery capacity loss with the factory provided charger is around 15-20% a year (considering "normal" to "heavy" use). That is to say that after a year your battery will only reach 80-85% of the maximum charge it used to reach when it was new. And by that time your manufacturer expects you to consider buying a new phone, with more features.
Summing it up:
- calibration is just the process by which you "tell" your phone what the real specs of your battery;
- in normal use, charging your phone through USB is better than doing it with the manufacturer provided charger;
- try not to let your battery charge go under 20% nor above 95%;
- if you're interested, read more about it at batteryuniversity.com
Click to expand...
Click to collapse
You should post the source for your info, cause I am seeing a lot of incorrect information in here.
If you guys want to learn about your battery, visit the site Battery University
The OEM replacement battery is worth about $10.
Save yourself the stress....use it...charge it when you need to...if the battery ever fails cough up $10.
Sent from my GT-I9100 using XDA App
The way I would calibrate my batteries is a bit different. Lithium ion batteries don't need to be drained then charged to full AFAIK, and I even remember reading somewhere that draining it is actually only for NiCad batteries. It used to be relevant when phones were using NiCad but not anymore.
Read: http://batteryuniversity.com/learn/article/how_to_prolong_lithium_based_batteries
As such I have read that the universal way to 'calibrate' batteries is by charging to full, using for a couple of mins and charging again.
What I have been doing is:
1. Charge to full when phone is switched off (doesn't matter if it's from 0% or 99%).
2. Switch on the phone, use for 5 mins.
3. Switch off then charge until full.
4. Repeat step 2 once more
That's it! It seems pretty simple but it seems to have worked for me.
The way i do it is different. Firstly i have the battery calibration app from the market by Nema..then i fully charge my phone and when it says its fully charge i go into the app. There it gives me the instructions on how to calibrate...First i wait till i charge the phone without any interruptions. then click on the app and wait til the battery goes to 4200MV and then i press the calibrate button and then the app does it for me. Then i drain the battery again without any interuptions or breaks during that time and then charge it again once battery dies down and thats it.
there are so many ways being touted on the forums you really dont know which one to go for...but whatever works for each person then who are we to tell someone different just thought i share that
If my battery dies, or gets significally lower capacity after 1 or 2 years of usage, I'll just buy a new one if I plan to keep the phone longer.. Going through these rituals and painstakenly monitor my battery % so that it never goes below 20 % or above 95 % is just not worth it.. Doesn't increase the life THAT much anyway.. I use the phone until I hear the beep for low batt, and from there until I have a charger available.. Most of the time it's before it reaches 10 %, thats good enough for me.. Once in a while it might even go so far that it dies.. Then I charge it till it says 100 %.. Most of the times I plug it when going to bed, and let it charge over night.. This is normal usage and what the battery should be designed to handle, and so far it does..