today i put WM6.5 +QueROM Versions B1 on my herm 100. everything was fine till i instaled SPB Mobile shell. after install the phone freeze. i pull out battery and now won't bot. the scree freeze at that first windows splash screen. i think i broke my phone . any1 can help me to bring my phone back to life?
idk if this the right place for my problem, and sorry for my bad english
Just hard reset it and than it will works well again.
you press the two buttons above the send and end. (OK and WINDOWS BUTTONS) and keep them pressed, while they are pressed you press the reset buttonon the Device
Related
Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris
Hold down (and keep holding) the camera button while depressing the reset button. Hopefully it boots into a tri-color screen. If so, plug it into the USB port and, at the bottom of the screen, it should display "USB". If that happens, flash it with a *known good rom*, such as a stock T-Mobile rom. Don't try to be clever, the object is to get the phone working. Once the flash has started, *get up and walk away* for 15 or 20 minutes. Don't check in on it, leave it alone, It takes some time. When you hear it's little chime, it's done, rebooted and ready. If any of the above doesn't happen or the flash outright fails, then you may have trashed it permanently. It doesn't sound like it's beyond hope yet, however.
i have the wizard and im having the same problem after installing a ROM from this website...it just goes to the windows mobile screen with the numbers then shuts off...id really like to save my phone is there anything else i can try because that hard reset thing isnt working
axxeman001 said:
Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris
Click to expand...
Click to collapse
Well same thing happened to me a few days back.. I had to Cold Reset [which restored it to factory defaults], but hey I got it working again..
Press Communication Button [Top Left] and Record Button [Top Right] at the same time and use the stylus to soft reset..
You will get a black screen, asking you to press "Send" to reset to "Factory defaults"
Press "Send".
Hopefully you should get your MDA working again ...
I read the "Above" in the HTC Wizard Service Manual [PDF] on the *last page* under the "Cold-reset" Section..
Help me !!!
i can´t enter debug screen.
the upgrade was at 100 percent, i disconect my BA from usb, hardreset,
boot screen appears, i push record and media and nothing happend.
what can i do now ???
i´ve test it for 30 times and nothing change.
You need to hard reset and push the both BEFORE you see the divice info come up.
Takes a few goes.
Best is to hold a thumb on each button while holding the device.
Have the stylist up its bum and on your leg. the device on top of the stylist.
Now push the device down on the stylist (which is on your leg pointing up)
this will get you to boot, as soon as you see color push your thumbs.
thank you for your help but it hasnt work.
ive test it more than 40 times.it hasnt work.
now i ve downgrade my device back to 2003se
best wishes for the new year
i guess he hasnt pushed the "MAIL" Button to execute the commands... lotsa people do that and giveup.
i cannot enter debug screen.
when i see the 4 colored screen, i press record+media and nothing happend.
i think thear must pop up a menu, than i had to change the options and push the mail button.
but the menu doesnt pop up.
push Record+Media and hold on to it... now stick the SoftReset (still holding into Record+Media) then tell us what happens...
i have test it.
doesn´t work
Hello,
i've got the same problems.
Tried really everything.
Even mtty don't work.
Just the colored Screen and some seconds later the version number.
Any Ideas?
the only way i know to solve the problem
is to downgrade back to wm 2003se
Hi all,
since 2 days ago I have this problem. The screen switch off itsel,and sometimes the power buton just doesn't work.
Also, sometimes, pops up the window saying if I want to swich it off, like when we press the power buton for a few seconds...but without doing it!!
I really don't know what to do, is very anoying. I thought might be because the other day I went for a walk, and was raining, so could get wet(?) ..don't know if that could be the problem, but anyway, that was friday, and today Sunday still happen the same.
Any ideas? Might get the buton blocked? If so...how do I unblock it?
I check the screws, and don't know what tool would be good if i need.. might be an special one ?
Thanks in advance.
Carles
Screen switches off
I have a Tytn (Hermes) the phone comes on sometimes and works , then on occasions it would be on , but the screen is off . The backlight stays on but nothing on screen. Push the power button and sometimes it will come back on , other times i have to remove the batt and wait a couple of hours before the screen comes back on . When it is like this then even if you reboot , it goes past the htc logo and just before windows loads the screen goes off .I have re installed the shipped roms again as at first i thought it was a software problem . I can see my phone on active sync and i can also load software to and from the phone , even with the phone screen off . any suggestions would be appreciated . Thanks
Natty Fish
guys i've installed spb pocket plus and I didn's like it and removed it, after removal the device wanted soft reset. I restarted it but its stucked on the windoes mobile screen ... what to do ??
first take out battery for 30 mins then retry.
if that doesnt work and soft reset doesnt work, then im afraid its hard reset time and you will loose all your data on your device you know how to hard reset yes? press and hold camera & comm button and keep pressed, then soft reset keeping buttons pressed until warning screen comes up asking you to hit green button.........
thanks my friend the xda is now like brand new
no problems, congrats
Hi,
I have got my trinity phone one year ago and never had a problem since last week. When starting my phone, it stops on the first screen (with "orange" logo) and nothing more happens.
I tried to reset it without succeed. The phone is not detected by the "activeSync" to make it flushable.
Help please !
Yves Florent CK
my problem is mor or less the same... only that dont apears any image on screen and the green led is constantly on...
I have loaded a long time ago an old version of ROM Gelly.
This ROM worked perfectly to a friend who suggested to do the same with my trinity.
The PROBLEM is that when i try to open the pda it freezes to the first srceen showing the rom version and after....nothing!
I tried to load again Gelly from the bootloader, it begins to run, it runs about 1% then the trinity makes a flash (this means it loses the connection with the pc) and then shows me again the first screen....
Please i need help!
me to. i try install the rom original and my pda is living again.
try this to
hi,
2 things ...
have you tried a hard reset ? (hold both softkeys & hit reset button)
and when flashing:
when you first run the rom upgrade from PC with phone on Activesync, it is quite common for phone to hang at the bootloader screen ...
worry not -
just re-run the upgrade from PC again immediately, without disconnecting or attempting to switch phone off.
(the word USB should be visable on device under the coloured bars)
if you do get hung up at bootloader screen a hard reset should at least get you back to where you were, and you can try re-flash again.
hope this helps,
regards,
Kevin
My trinity won't work anymore...
Hi all!
My trinity wont't work anymore. When i press the ON/OFF-button, the display is lighten up a bit, then the buttons are lighten up. And nothing more.
When i will go to bootloader mode, it is the same.
And when i will to a hard reset, the trinity ask me to press SEND or END key for restore factory default or cancel. When i choose the SEND key, on my display some ridicoulous letters appear, but nothing more.
When i try KITL mode, everything is the same.
Can someone help please?
Because i can't do something on my trinity
EDIT (maybe this can help my helper ):
After some time, the display and the buttons are not lighten up anymore.
When i try to charging the battery, it only works, when the buttons are not lighten up (when i switch on, charging is ok; when the display is lighten up a bit, charging is ok; when the buttons are lighten up, charging won't work; when the display and the buttons are not lighten up anymore after a time, charging is ok)
hi... i have a similar problem.. i tried soft reset, hard reset, but my phone wont go past the boot screen.. previously i just updatet the windows mobile from 5 to 6 and the phone crashed half way throw.. can some one help me.. by the way the windows mobile was one update from the web...
never mind... problem solved... tks anyhow
weezer_88 said:
never mind... problem solved... tks anyhow
Click to expand...
Click to collapse
ok solved...
Can you tell how you did it?
Thanks
weezer_88 said:
hi... i have a similar problem.. i tried soft reset, hard reset, but my phone wont go past the boot screen.. previously i just updatet the windows mobile from 5 to 6 and the phone crashed half way throw.. can some one help me.. by the way the windows mobile was one update from the web...
Click to expand...
Click to collapse
But my trinity don't go to the boot screen, nothing on the display but lighten up slightly...
Nevertheless, can you please post, how you solved your problem?
THANK YOU in advance!
I downloaded the original Rom windows mobile 5 from http://www.htc.com/www/SupportDownload.aspx?p_id=3&cat=2&dl_id=111 then entered in KITL mode, connected the usb and reinstalled the original Rom, and all was fine...