Just installed the xda-developrs SE ROM
Seems to make the XDA run like a deamon, well impressed so far.
Just as everybody else though. The autoconfiguration doesn't work. So can't get the o2 wap settings up.
dns 193.113.200.200
and 193.113.200.201
np mobile.o2.co.uk
but something seems to be missing. Could somebody please supply the complete settings.
WAP...
Ehm, as far as WAP goes...
We did not include the EZWAP program in our install. So WAP is unlikely to work. WAP wasn't in Othman's Qtek ROM (it has no autoconfig settings and no WAP), and we didn't create mkrom to take input from multiple ROMs. We figured serious users would want to the new EZWAP which also does MMS (which isn't included by O2), and we never really used WAP or MMS ourselves. So I guess we never tested any WAP settings...
If you want you can have a look at the registry settings we insert for each provider in the 'provider' directory of the mkrom kit. If you think some settings are missing, you could do a registry dump (using the 'System Snapshot' we put in the ROM) before and after fixing the problem, and send us the differences. We can them insert them in next versions of the Special Edition ROM.
02 internet settings
Is this what you want?
Name: 02 Mobile Web
Select a Modem: Cellular Line (GPRS)
Baud rate: 19200
Advanced:
TCP/IP:
Use Server- Assinged IP Address
Name servers:
Use specific server address
DNS: 192.113.200.200
ALt. DNS: 192.113.200.201
WNS: 0.0.0.0
ALt. WNS: 0.0.0.0
Access point name:
MOBILE.02.CO.UK
Name 02 MOBILE WEB GSM
Select a modem: Cellular line
Baud rate: 19200
Advanced:
Connection perferences:
Port Settings:
Data bits: 8
Parity: NONE
Stop bits: 1
Flow Control: Hardware
TCP/IP:
Use server-assigned IP Address
X Use software compression
X Use IP header Compression
Name servers:
Use specific server address
DNS: 192.113.200.200
ALt. DNS: 192.113.200.201
WNS: 0.0.0.0
ALt. WNS: 0.0.0.0
Country code: 44
Area number: 771
Phone number: 2932932
Name : 02 WAP GPRS
Select a modem: Cellular Line (GPRS)
Baud rate: 19200
Advanced:
TCP/IP:
Use Server- Assinged IP Address
Name Servers:
Use server-assigned address
Access point: wap.02.co.uk
name: 02 WAP GSM (CSD)
Select a modem: Cellular Lime
Baud rate: 19200
Port Settings:
Data bits: 8
Parity: NONE
Stop bits: 1
Flow Control: Hardware
TCP/IP:
Use server-assigned IP Address
X Use software compression
X Use IP header Compression
Name servers:
Use server-assinged addresses
Country code: 44
Area number: 771
Phone number: 2927927
There ones I use my self
UK 02 XDA
Hi,
Thanks for the above info. It worked a treat. However I was asked for a Username, Password and Domain login when I connected to GPRS. So for those of you who do know it, here we go:
Username: web
Password: password
Domain: leave this blank.
Check the box to save the password.
Gil.
thanks, i will add it to my txt file
missed those
I am on O2 payg, using the xda, I have tried the gprs settings and it says the number isnt responding, when I use the gsm settings that are preset when doing auto config, I get charged even though I am on 300 free wap minutes, I dont think I am a stupid person but I have a feeling of having been here before when I previously had an O2 payg, any help would be appreciated. I am getting the free sms messages so I know the account is activated for the freebies. The "G" sysmbol comes on when i switch on the xda and stays there for about 10 seconds.
Hi. I'm new here so excuse me if I seem simple! I have unlocked my XDA using xdaunlock and now have same problem with GPRS dropping out after approx 10 seconds. It worked before, so has unlocking changed any settings? or has something else happened. The xda has the latest uk rom upgrade with 4.21 radio. Any help please as I dont know what to do! Thanks.
Please has anybody actually got a working setup for GPRS on O2 PAYG on the XDA, I have spent weeks on this and got nowhere. I have followed instructions to the letter from different websites and still no joy, I can connect to wap over gsm but gprs settings still elude me, anybody got a full description of settings please, and how to enter them. Thanks in advance.
Is there nobody on this forum using O2 PAYG sim and using wap over gprs? I cannot seem to find anybody with the settings, I wonder why, it seems like the holy grail just to get on line using the system that is available to me in theory? Help would be greatly appreciated.
Nobody in UK on O2 pay as you go :?: :?: :?:
Update on my problems with GPRS on O2 payg. I have tried every setting on this forum plus others, I always get error, not answering or some such, I have decided to stick to gsm connection using shortcode 951000 and exwap 2.5. if anybody can give me step by step, confirmed working settings, I would apprectiate it. This will be my last post on the subject, I am beginning to take up too much storage on the forum server with this. A resolution to the problem would be great as I can then save my connection settings to flash ram and not worry about it again.
cruisin-thru I am not on O2 so can offer limited help.
EzWAP2.5 could be yr problem.
I sometime find difficulty using WAP after a session mms'ing with EzWAP2.5 . A solf reset is then required before I can connect to WAP via gprs.
Here is my sugestion:
1.uninstall EzWAP2.5 completely
2.try to get connected to gprs or gsm WAP
3.try PIE, it works for WAP , but depending on yr
telco whether on gprs or gsm
4.if all the above is working then install EzWAP2.1
and see if it works
5.then EzWAP2.5 and see if it screw up everthing,
if not try mms.
Hope this helps, i am working blind here
OK, searched high and low and think this is the best thread to post this in.
Have just upgraded my XDA with the developers rom v1.2. Everything great for a while (3 days) Now it can not connect to gprs or gsm. I get the "There is no answer at the number dialed.
I am with O2 UK and have treble checked the settings and tried various alternatives however nothing works.
One thing I have noticed is that the autoconfig dropdown box says Austria One.....when I change that to O2 - UK and click OK to autoconfigure, it doesn't, it just comes back to Austria - One.
Phone works and SMS is fine, just GPRS/GSM
Do I need to re-flash or contact my provider....or please tell me there's a simple "fix" :lol:
Thanks
Ive got this reply through email from o2 im waiting now for password and username I will post soon as I get it
Go to Start > Settings > Connections > Connections, and then select the top modify option. Within this, there should be four connection types.... Select the GPRS WAP connection and modify the settings. You need to change anything that says o2wap to payandgo, and change the APN from WAP.o2.CO.UK to PAYANDGO.O2.CO.UK. Once you have amended these settings, tap and hold on this connection type and make it your default. You might want to rename this
Then, go into the EZwap application, and select tools and then options, and there should be a series of tabs. Select the general tab and make sure the connection in the drop down list, is the one you have just amended.
Click to expand...
Click to collapse
im on o2 online genie payg 300 free wap/txts per month.
i got my txts down to 200 and i get 25free mms per month instead
i got all wap/net working for free
just follow these bits of info it all works as i have it on my xda running wm2003 no need to config dsn and ip things in the advanced bit leave them how they are:
settings are:
MMS
Data bearer: GPRS
Access point name: wap.o2.co.uk
Username: o2wap
Password: password
Authentication: Normal Gateway IP address: 193.113.200.195
URL address: http://mmsc.mms.o2.co.uk:8002
Session mode: Permanent
GPRS
O2 Wap / Mobile Internet settings:
Homepage: http://wap.O2.co.uk/
Dialup access number: +44 771 2927927 (915000 dont work for xda)
APN (GPRS only): payandgo.o2.co.uk
Gateway (IP) address: 193.113.200.195
Username: O2wap
Password: password
Session type: Continuous / permanent
Port number: 9201
Note: Until May 2002, O2 Wap was known as Genie Wap (username 'geniewap').
The alternative dialup number of +44 7712 927 927 is also available,
although this number may not be free when used with O2 online
Hi, make sure first that it's your GPRS WAP connection that Ezwap is using, and set it to 'auto connect' in 'Options'
under the 'connection' tab set connection type to 'gateway' and put in your networks WAP IP address (o2 IRL's is 192.168.090.074). Click on 'connectionless gateway'
Untick 'wtls' secured connection.
Click on the 'MMS' settings tab next.
Put in your networks MMS 'Message Server' or MMS homepage. (O2 IRL's is http://mmsc.mms.o2.ie:8002)
All the other settings can be setup as you like.
1) Enable MMS on my account. Had to get 'pally' with a tech guy to do this as XDA is not supported; I suppose pretending I had a 7650 would have worked too.
2) Install EZWAP2.5
3) EZWAP Settings for O2UK:
General
"Connection"
- O2 WAP GPRS
- Connect automatically Y
- Rest on this tab default
Connection
"Connection Type"
- Gateway
- Address 193.113.200.195
- Port 9201
- Connectionless Gateway N
- WTLS secured connection N
- Rest on this tab default
Push
"Push"
- Enable push Y
- Connection type Address: blank
- Port 2901
- Connectionless Push gateway Y
- WTLS secured N
History/Cache & Identification - default
MMS
"MMS Settings"
-Message Server: http://mmsc.mms.o2.co.uk:8002
-Sender Address Type: Phone Number
-Sender Address: My phone number
MMS Options - delivery recepit and read receipt Y
It's not 100% reliable, which I knew would be the case, but it's not too bad. Get now when the message arrives doesn't work, but I just open the MMS inbox and click the message to get it.
ntl
username: Normal
incomming: pop.ntlworld.com
outgoing: smtp.o2.co.uk
02
username: [email protected]
incomming: mail.o2.co.uk
outgoing: smtp.o2.co.uk
Hotmail
username: [email protected]
incomming: http://services.msn.com/svcs/hotmail/httpmail.asp
outgoing: http://services.msn.com/svcs/hotmail/httpmail.asp
Can someone create a cabfile which creates the registry entries in WM2005 for the COM5 Bleutooth entries. In WM2003(SE) the COM5 was defined for outgoing BT connections. I used it for my BT GPS. Within my GPS Navigation software I only can choose one of the declared COM ports. When I pair my BT GPS I can specify with the COM Ports tab that my GPS can be found at COM5. But COM5 is not listed in WM2005 as an available COM port. Does anybody now how to create an registry entry for this?
After you Pair up the GPS:
Then Go COM Ports / then select Outgoing Port / then select Com5
That's it.. )
THANX Jose...
buzz
Hey,
Has anyone been able to get TomTom online with the t-mobile t-zones.
I use a Tomtom standalone navigation system that's connected to my phone via bluetooth.
I can get online with the proxy settings on my phone.
How do I set up TomTom?
Please let me know if some has done this before.
it cannot pass thought t-zone proxy, setting for proxy on TomTom
where do you set a proxy on tomtom? is that possible?
Can I just tell tomtom to go "through" my cell one, use that internet connection?
solution
Hey,
I found a solution on the tomtom forums:
After the auto-config fails I used these manual settings on my TomTom ONE:
APN: wap.voicestream.com
Username:
Password:
Dial: *99#
Connection string: AT+CGDCONT=1,"IP","wap.voicestream.com" (case and whitespace sensitive)
http://www.tomtomforums.com/showthread.php?t=1163
_______________________________________
Having Hard Reset my T-Mobile MDA Vario II and installed needed software applications I became challenged.
When Bluetooth pairing my Holux GPSlim236 GPS Receiver I was unable to select the needed communications port COM4
On my PDAs I have installed the Registry editor “PHM RegEdit”.
When I looked at my MDA Vario II Registry all GPS Settings was blank
Here I document and share the Registry and Device settings from scratch that resulted in my device pairing and Satellite Navigation working properly using TomTom Navigator v6.
1. Registry GPS Intermediate Settings
Select PHM RegEdit, or the editor that is your preference, and
Select HKEY_LOCAL MACHINE, select System,
Select CurrentControlSet, and Select GPS Intermediate Driver,
Saving repetition when prompted select OK
Select the Key name “Drivers” if it does not exists
Select “Edit”, New Key and type Drivers
Select Drivers and “Edit” and select New String Value
Value name: Currentdriver and
Value data: Control Panel Configured Device
Select Drivers and “Edit” and
Select New Key and type Control Panel Configured Device
Select Control Panel Configured Device
Select “Edit” and select New DWORD Value
Value name: Baud and Value data: 4800
Select Drivers and “Edit” and select New String Value
Value name: CommPort and Value data: COM4
Select Drivers and “Edit” and select New String Value
Value name: InterfaceType and Value data: COMM
Select Multiplexor and “Edit” and select New String Value
Value name: DriverInterface and Value data: COM5
2. Registry GPS Settings
Open HKEY_LOCAL MACHINE, select Control Panel
Select GPS Settings
Select “Edit” and select New DWORD Value
Value name: Group and Value data: 2
Select “Edit” and select New DWORD Value
Value name: Hide and Value data: 0 (that is value zero)
Exit Editor and Soft Reset Device
3. Device Connection Settings
Select Start, Settings, Connections and GPS Settings
Select GPS program port: COM5
Select GPS Hardware port: COM4 and select a Baud rate: 4800
Select Access and check box Manage GPS automatically (recommended)
4. Device Bluetooth and GPS Receiver Settings
Select Comm Manager and ensure Bluetooth is turned ON
Select Bluetooth Settings and COM Ports
Select and hold Holux GPSlim236, select “Edit”
Select Bluetooth Port: COM4 and select Finish and OK
5. TomTom Navigator software and GPS Receiver Settings
Start TomTom Navigator v6
Select Change preferences, Show GPS status, Configure
Select Other Bluetooth GPS receiver and select
Select GPS is connected to: COM4 and select done
Another intellectual challenge put to bed
PS I can confirm that settings documented here perform satisfactory on WM5 and WM6 device
watchdog2003 said:
_______________________________________
Another intellectual challenge put to bed
Click to expand...
Click to collapse
ummmm...here's the pat on your back you were looking for
*pat*
I'm sure someone may find this helpful though...and I'm sure that's why you posted this.
For sure.
This a Tutorial tested in Lebanon Because Lebanese 3G Connection is very expensive
ANDROID 2.2+ ONLY
PREREQUISITES:
- Rooted Android phone
- The WAP needs to be set up first, activated and working (web browsing).
Step One :
1 - Download ProxyDroid from the Market (free) via Wi-Fi
2 - Turn OFF Wi-Fi and make sure packet data is disabled.
3 - Configure ProxyDroid:
Host: 192.168.23.50
Port: 8080
Proxy type: HTTP
Tick Auto Connect
Binded Network: 2G/3G
Tick Enable Authentication
User: mic1
Password: mic1
4 - Enable packet data (WAP)
5 - In ProxyDroid, enable the proxy (tick Proxy Switch)
6 - Open For Example Whatsapp and wait up to 15 sec so that the configuration takes effect
Note : To block unwanted application from receiving internet, use DroidWall
ProxyDroid : https://play.google.com/store/apps/details?id=org.proxydroid&hl=en
DroidWall : https://play.google.com/store/apps/details?id=com.googlecode.droidwall.free&hl=en
Thank You For Your Support