i have been searching for 2 days for the original bell galaxy s jh2 firmware so i can flash my phone back to 100% stock and exchange it for a new one (mine wont boot into recovery with the 3 button combo).
i am looking for the bell version, including all of the pre-installed bell crapware, etc. can anyone provide a link to either an update.zip file or the files needed for odin? i was trying to un-root my jh2 software yesterday morning and couldnt do it, so after a bunch of flashing, and two near brickings i am now on jm6 firmware but now kies wont connect to my phone. all of the drivers are there, and i have uninstalled and reinstalled kies already but my phone will no longer connect.
i downloaded the jh2 files from http://www.samsungflash.com/wiki/I9000 and tried to flash with odin but it left my phone in a bricked state. the files provided were only the pit and pda file and the flash just wouldnt work. i have only been successful with odin when using separate pda, modem, and csc files. any help would be appreciated
When you turn on your phone what does it do exactly? Does it boot into the OS, or just stay on the Samsung screen?
Have you tried using the Bell firmware (JH2) found here. That is the provider file. So if you can find the PDA and PHONE file you like then that file should return it to stock.
Post back with results.
gold_sprinter said:
When you turn on your phone what does it do exactly? Does it boot into the OS, or just stay on the Samsung screen?
Have you tried using the Bell firmware (JH2) found here. That is the provider file. So if you can find the PDA and PHONE file you like then that file should return it to stock.
Post back with results.
Click to expand...
Click to collapse
my phone boots up fine, it was completely screwed up yesterday but i actually ended up flashing to the software you linked to. that software doesnt have any of the bell stuff in it.
thanks for trying, though
edit
i forgot to type in the code at the end of those instructions and it hard reset my phone but now the bell stuff shows up. thanks! the only problem is that the software doesnt show up as jh2, but the apps are there. one step closer
If you are to return it to bell in this state, would they really look to see what firmware was flashed to it. Especially if you are returning it because of the 3 button problem? As long as it boots up and they can see you have not broken it, this should be sufficient.
Correct me if I am wrong.
gold_sprinter said:
If you are to return it to bell in this state, would they really look to see what firmware was flashed to it. Especially if you are returning it because of the 3 button problem? As long as it boots up and they can see you have not broken it, this should be sufficient.
Correct me if I am wrong.
Click to expand...
Click to collapse
i just dont need the hassle if they notice it is rooted and dont want to take it back.
member Richthofen sent me a link to the files and i used odin to flash back. it is now 100% stock.
That is awesome, glad to see it worked for you. Would you mind linking to the files so others with the Bell brand can do the same?
http://www.multiupload.com/N62CDNXXXK
this is a link to the files needed to use odin to flash back to 100% stock bell firmware. thanks to richthofen for the file
Sorry to revive an old thread but I think this is the ideal spot to put this question. My SGS I9000M is stuck on the boot screen so this will be my first try with ODIN.
I have installed ODIN 4.03, and I have downloaded the above file and unzipped it with 7ZIP. It contained one .tar file. I put my I9000M into downloading mode, launched ODIN and plugged in the phone. It was detected and says com port mapping 1 (COM5) on ODIN. I ticked the One Package option box and selected the .tar in the One Package address box. Already selected were Reboot, Protect OPS and Reset Time (300 ms). I clicked start and a popup said "Check Image Files!!". I clicked okay. The log box to the left indicates "Download Start..." but nothing appears to be happening, and the start button is available to be pressed again.
Did I miss something?
Thanks!
_____________
UPDATE: Okay, Looks like you need ODIN 3, version 1.0, as far as I can tell, so I have installed that, put phone in download mode, plugged it in and ODIN detects is (0(COM5)) There is no One Package option so I went with PDA.
The following appears in the log window:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> dbdata.rfs
The phone screen went blank and is non responsive. There is no apparant change in ODIN. I'll let it sit for a while unless someone can redirect me on this?
Thanks.
Mad Medik said:
Sorry to revive an old thread but I think this is the ideal spot to put this question. My SGS I9000M is stuck on the boot screen so this will be my first try with ODIN.
I have installed ODIN 4.03, and I have downloaded the above file and unzipped it with 7ZIP. It contained one .tar file. I put my I9000M into downloading mode, launched ODIN and plugged in the phone. It was detected and says com port mapping 1 (COM5) on ODIN. I ticked the One Package option box and selected the .tar in the One Package address box. Already selected were Reboot, Protect OPS and Reset Time (300 ms). I clicked start and a popup said "Check Image Files!!". I clicked okay. The log box to the left indicates "Download Start..." but nothing appears to be happening, and the start button is available to be pressed again.
Did I miss something?
Thanks!
_____________
UPDATE: Okay, Looks like you need ODIN 3, version 1.0, as far as I can tell, so I have installed that, put phone in download mode, plugged it in and ODIN detects is (0(COM5)) There is no One Package option so I went with PDA.
The following appears in the log window:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> dbdata.rfs
The phone screen went blank and is non responsive. There is no apparant change in ODIN. I'll let it sit for a while unless someone can redirect me on this?
Thanks.
Click to expand...
Click to collapse
Disconnect phone from pc if not done already.
1) restart Odin
2) tick "repartition"
3) choose 512 pit file
4) put phone in download mode, connect phone to pc, click START in Odin
5) Once Odin says "PASS", disconnect phone
6) remove and replace battery
7) In Odin click "reset", untick "repartition", put tar file in "PDA"
8) put phone in download mode, connect phone to pc, click START in Odin
9) Once Odin says "PASS", disconnect phone and just let it reboot
10) Voila, you're back to 2.1 stock
Good luck!
donkeyhitman said:
Disconnect phone from pc if not done already.
1) restart Odin
2) tick "repartition"
3) choose 512 pit file
4) put phone in download mode, connect phone to pc, click START in Odin
5) Once Odin says "PASS", disconnect phone
6) remove and replace battery
7) In Odin click "reset", untick "repartition", put tar file in "PDA"
8) put phone in download mode, connect phone to pc, click START in Odin
9) Once Odin says "PASS", disconnect phone and just let it reboot
10) Voila, you're back to 2.1 stock
Good luck!
Click to expand...
Click to collapse
I had black screen after s logo boot.
So I used Odin 7 new to re-flash jk3 the bell version. And when it booted up first time I get mount error and vol + home and power does not work only download mode works. I flash like 15 times same ****. Even used different check marks repartition and boot loader all did not held any results.
Now that I sent it back to bell, I wonder if I had used Oden 1.3 instead of Oden 1.7 if that would have helped at all
I think it's the defective internal sd memory, as my phone is bell phone and I keep reading problems with the internal sd memory.
Do you think it could have been revived or am I right it is defective memory.
So I sent it back
Related
I recently bought my SGS International version and very pleased with it, in an attempt to improve its performance I tried to install a new ROM.
The process of hacking the root user I didn't encounter any issues, however, when I tried to flash using ODIN it didn't seem to work. I selected the files, connected SGS (debugging mode), the software recognized the phone (yellow bar with com port), but I click to start received the following:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
It seemed to be stuck on file analysis.
Perhaps the ODIN version I'm using isn't up to date? With that in mind can anyone give me a download link? (had trouble finding one).
Also, I'm not sure if it's related or not, but Kies refuses to recognize my device, it's getting stuck with the message connecting.
Any thoughts?
Thanks!
uncheck the debugging mode.
you must boot into a special mod named download mode.
to do this, you have to power down your phone, take the battery out for a few sec, remove sim and external sd card,then plug in the battery and press volume down button, keep it pressed, press home button, keep it pressed, then press power button until you see an android robot with a shovel. it will say:downloading... and below: do not turn off target!!! then you can open odin, select the files you want to download then connect the phone (important!) then you can start flashing.
hope this helps.
u dont need to take the battery out to get in to download mode!
you know just for dischargement and safety, this will be 100 percent safe if odin doesnt screw up.
Thank you all for your replies!
However. I run odin while the phone is download mode, I have the digging android while I do the above
Odin 1.7 is on the forum or google/search .
Your problem may be the rom rather than Odin ..
http://forum.xda-developers.com/showthread.php?t=846913
jje
Thanks for the link, the rom is darkys, which is well known. I'll try with a newer version of odin when I get home
the rom is darkys, which is well known
Known for what ???
jje
It failed with another rom I tried though
Eladku said:
It failed with another rom I tried though
Click to expand...
Click to collapse
No offence but I think you haven't got a clue what your doing. Best to research some more and actually understand what your trying to achieve.
Hello,
I recently flashed the Overcome ROM/Kernel (I'm still quite a noob though). After call volume issues I tried to flash the stock rom using the files from samfirmware.
I can flash the PIT successfully, it's when I try to flash the PDA file (either overcome kernel or stock firmware) I get this:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> zImage
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone help me or am I now the not so proud owner of a expensive and stylish paperweight?
Any help would be greatly appreciated.
First let me get this right. You would like to go back to sgt stock rom after flashing the overcome kernel?.
As long as you can boot into download mode. There is still hope. If odin is giving you problems try Heimdal to flash zimage modem and other files from the samfirmware archive. If you still want to use odin. Try doing a factory reset and a wipe from recovery (vol up and power).
Just a word of caution samfirmware roms might have signed bootloaders. Which can be a hinderance for flashing custom roms in the future.
Heimdal doesn't want me to click start (it's greyed out).
I've put the pit, pda, modem and CSC files in and it's still greyed. Am I doing something wrong? I installed the drivers as stated in the read me.
Edit: Got a bit of life out of it, when I uncheck everything but PDA it allows me to click start but throws: Failed to access device. Error: -12
Then Try a factory reset and a wipe from the Recovery mode. Wipe it clean and start fresh.
I couldn't get into recovery.
I've just changed the driver to the unsigned ones (not the originals as stated in readme) and it seems to be working at the moment....
fingers crossed
It wouldn't go past the galaxy tab screen so I tried again and the same I get an image of a phone, exclamation mark in a triangle and a pc. I think this is like download mode as I can still access via odin which allows me to flash the PIT and get download mode back.
It seems a problem with the zimage process, I've tried 3 different versions with no luck
Thing seems dead now. It made a loud beep when I plugged it in to the PC but that's it
Plug in your wall charger and see if Tab charges. If it charges fully charge the tab and try a RESET. You might want to try ROTO ROMs at development section first to get your tab started before going into any trials with stock ROMs.
Personally i use odin. Find it easier.
If you followed the instructions for overcome, clockworkmod recovery is installed by default
All you have to do is copy the Overcome rom zip file (200+meg) to your ext sd card.
Boot to clockworkmod recovery (power+up buttons)
Clear all caches
Select install rom from sd card
Choose overcome zip file
Install
Reboot kernel is installed with rom
______________________
Overcome 1.2.1 at 1.4GHz
Quadrant 2290
it doesn't want to charge, it seems it can't draw enough power from USB to even run off that.
When plugged into the wall I get the phone, triangle, computer screen and it constantly restarts after less than a second.
Think I'll just have to take it back to PC world and act dumb (like the staff)
Left plugged into the wall over night, the battery is still dead.
I'll faf around a bit more today and if no progress I'll just return it to the store.
Thanks for your help
Tired plugging into rear usb and after a while it turned on and went to the phone - triangle - computer screen (some sort of alternate download mode) flashed PIT with odin, this enabled me to actually get into download mode (or see the galaxy tab logo til the battery dies if I want to). Then flashed rest of the files with Heimdall, still the tab doesn't allow me to turn on. Thinking it might be due to low power I plugged into wall charger, usually when the tab is charging when turned off you see the battery image with the green level indicator, all I see is an empty battery with the sort of loading thing in the middle of it (though it isn't going round). Still doesn't seem to want to charge (or turn on) is the charging process governed by the kernel?
Just called PC World support, told them I turned it off last night to charge and when I turned it on it just showed the galaxy tab screen. They said just take it instore and they'd swap it
Hello everyone I'm a newbie in Android. A had a Nokia N97 mini and now i bought a Samsung Galaxy S 2. Beeing new to Android it was kinda hard the first days to adapt. But i did. And now to tell you about my problem.
Whenever i try to copy some movies/sounds/photos from pc to S2 it gives me this error "The path is too deep". So i tried to copy in a more direct path.. Still nothing... But the big problem is that i cannot update my phone through Odin. Wheter is Android 2.3.3 KE7 or 2.3.4 KG1 or a ROM I'm not able to do it. And I decided to update thru Kies. All good but the update failed... It said it need to enter Recovery Mode. I clicked ok and then my pc rebooted. Then i got this image on my phone with a pc and a phone, chained together by an exclamation mark inside an orange triangle... And now i cannot restart my phone, i can't do anything.
Is it bricked? Please help me...
TudorMondialul said:
Hello everyone I'm a newbie in Android. A had a Nokia N97 mini and now i bought a Samsung Galaxy S 2. Beeing new to Android it was kinda hard the first days to adapt. But i did. And now to tell you about my problem.
Whenever i try to copy some movies/sounds/photos from pc to S2 it gives me this error "The path is too deep". So i tried to copy in a more direct path.. Still nothing... But the big problem is that i cannot update my phone through Odin. Wheter is Android 2.3.3 KE7 or 2.3.4 KG1 or a ROM I'm not able to do it. And I decided to update thru Kies. All good but the update failed... It said it need to enter Recovery Mode. I clicked ok and then my pc rebooted. Then i got this image on my phone with a pc and a phone, chained together by an exclamation mark inside an orange triangle... And now i cannot restart my phone, i can't do anything.
Is it bricked? Please help me...
Click to expand...
Click to collapse
Ok. Stop. Breath. Your phone isnt bricked...yet.
Your phone is currently in 'download mode'.
Im not sure which directions you were following, did you download the software from intratechs thread in development? If so, he has step by step directions in the opening post.
You should be looking to install kf2.
http://forum.xda-developers.com/showthread.php?t=1075278
[ROM + Guide]Official i9100 KE7/KE8/KF1/KF3/KF4/KF2/KF3/KG2 download and Root Guide.
Remember, your phone is already in download mode. So just connect it to the pc, and then dont touch it .
Sent from my GT-P1000 using XDA Premium App
If your pc is rebooting when you try to perform an update then it's more than likely an issue with your pc.
I don't think your phone is bricked as stoney73 has stated as well it's in download mode
bricking a phone isn't that simple unless something abnormal happens (e.g. unplugging the cable while flashing a rom), I am sure your phone is fine. The feeling I have is the drivers in your PC are not installed/working properly, since I don't see the reason that flash via Odin will fail (Kies is another story...), try reinstall the driver and flash again
you may like to read this amazing thread to understand some fundamental terms (such as recovery and download mode)
http://forum.xda-developers.com/showthread.php?t=1134290
Also remember that Kies often gets in conflict with Odin, so open task manager in windows and kill all kies processes before using Odin.
Reply
Friends, i know what Download Mode is. And i tell you this is not the case. The phone was in recovery mode and then, all of a sudden an image appeared: and that image is not download mode. It's a little phone and a pc connected together by a small triangle orange with an "!" in it. I repeat, it's not in download mode.
If i pull out the battery the phone shuts down. Then i put the battery back in, start the phone in download mode :Vol down+Home+Lock and it sais :Vol Down-Restart the phone or Vol Up- Enter Down Mode. If i press vol down the phone shows that irritating image again(with the phone and the pc) and if i press vol up it enters download mode...
The firmware is official... Will i need a USB Jig to bring back my phone to life ?
PS: I have the latest drivers, Any Kies process has been stoped in Task Manager before the update and i followed step-by-step guides to update it. I tried 2.3.3 KE7, 2.3.4 KG1 and Lit'ning ROM. Neither would work for me, update failed at all was shown...
I'm really desperate...
Can you take a photo of what you are seeing?
this is it...
TudorMondialul said:
this is it...
Click to expand...
Click to collapse
That is also download mode. So your phone isnt bricked. If you connect your phone to the pc, stop kies from running, and then run odin, does the square under id:com turn yellow?
like this:
what should i do ? Should i try again with odin ?
In the PDA Section What should i put in ? WHat's the latest firmware...
LE: Yes that square turns yellow and it sais added but after a few seconds the whole thing freezes... No progress bar, nothing...
TudorMondialul said:
what should i do ? Should i try again with odin ?
In the PDA Section What should i put in ? WHat's the latest firmware...
Click to expand...
Click to collapse
The thing to do is to follow the directions in Intratechs thread: http://forum.xda-developers.com/showthread.php?t=1075278.
From Intratechs opening post:
"1. Just download the firmware version you want from above and extract the .tar file in the archive and save it somewhere
2. Reboot your phone to download mode.(Ignore, your phone is already in download mode, )
To get download mode shut down the device. After it shuts off completely simultaneously press the Down volume key+ Home button + press the power button .
You should see a warning asking you to press volume up if you want to continue or volume down to cancel, press volume up. You are now in download mode!(again ignore, you are already in download mode.)
3. Start Odin
4. Click on the PDA button and browse to the .tar file that you extracted in step 1
If the package has more than one .tar archive then they will be labelled with PDA, Phone/Modem and CSC. Just put them in the corresponding section of Odin
5. DO NOT PUT .PIT FILE AND DO NOT, I REPEAT, DO NOT TICK REPARTITION.
6. Connect the USB cable and wait for the ID:COM section to turn yellow
7. Click start to flash
8. Do not disconnect the cable or turn off the device, it will reboot when it finishes. "
TudorMondialul said:
what should i do ? Should i try again with odin ?
In the PDA Section What should i put in ? WHat's the latest firmware...
LE: Yes that square turns yellow and it sais added but after a few seconds the whole thing freezes... No progress bar, nothing...
Click to expand...
Click to collapse
So Odin freezes?
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Yes it freezes or it sais this(see above)
I maybe accidently have ticked repartition... is this a dead end ?
Try uninstalling kies AND the usb drivers then install them again and try once more.
Do you have access to another PC?
Are you using the official samsung usb cable?
So i should uninstall kies and then try again with odin? Yes i use the official Samsung USB Cable...
TudorMondialul said:
So i should uninstall kies and then try again with odin? Yes i use the official Samsung USB Cable...
Click to expand...
Click to collapse
Just saw your post about clicking repartition are you sure you done this?
If you have then you need a .pit file as per intratech's notes on the dev forum
.PIT refers to the partition information table you only need it if you screw up your partition table or if the firmware specifically requires it because of a change in the partition table layout. It's very likely you may never have to use this.
I think you might need to flash the csc, pda, pit and everything else separately.
Can some others confirm this?
I kinda trusted this site, this is where i got the instructions...
http://www.dkszone.net/install-android-2.3.4-xxkg1-samsung-galaxy-s-ii
TudorMondialul said:
I kinda trusted this site, this is where i got the instructions...
http://www.dkszone.net/install-android-2.3.4-xxkg1-samsung-galaxy-s-ii
Click to expand...
Click to collapse
Did you try to flash 2.3.4 with that guide or 2.3.3?
2.3.4 i tried...
Hello everyone. Was trying to update my S7 Edge to the latest firmware, India. However. the phone got stuck in recovery mode. Cant even switch off the phone. Tried to reinstall in recovery mode once but that too failed.
Also the screen is on and the phone is warm for mre than 5 hrs. I am afraid some internal hardware might get damages. Its stuck on the green screen which reads :An error has occurred whil;e updating the device software. Use the emergency recovery function in smartswitch PC software.
The service centre are closed for two days due to Ganpati festival here. Need your urgent help.
Is this "recovery screen" cyan/blue? If yes then it's a odin recovery mode.
Just hold volume down + home + power until Your phone force reboots to odin mode.
But. If that doesn't do anything or still shows You that recovery screen, then just open odin on Your PC and connect Your phone. It should find Your phone anyway. Now all You have to do is flash any kind of image if Your phone has working boot.img and system.img. If not then reflash whole firmware and You should be fine
ProtoDeVNan0 said:
Is this "recovery screen" cyan/blue? If yes then it's a odin recovery mode.
Just hold volume down + home + power until Your phone force reboots to odin mode.
But. If that doesn't do anything or still shows You that recovery screen, then just open odin on Your PC and connect Your phone. It should find Your phone anyway. Now all You have to do is flash any kind of image if Your phone has working boot.img and system.img. If not then reflash whole firmware and You should be fine
Click to expand...
Click to collapse
Thanks a lot. I have downloaded odin software. But dont know how to install it? Trying to download the firmware file from sammobile.
Any tutorial available?
Chirag22ster said:
Thanks a lot. I have downloaded odin software. But dont know how to install it? Trying to download the firmware file from sammobile.
Any tutorial available?
Click to expand...
Click to collapse
you might get more help if you thanked people by clicking on the thumbs up icon.
riz157 said:
you might get more help if you thanked people by clicking on the thumbs up icon.
Click to expand...
Click to collapse
OK. Never realized a thumbs up thanks works more than a written and acknowledged thanks. Have done it.
Have been going through some tutorials. Just have a query whether to add CSC file or Home CSC file to odin folder?
So finally tried installing through odin. But received a fail message. Any suggestions? Received the following msgs.
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Sorry. I was busy.
Okay!
Tap on AP in odin and add Home image and then tap on start. Home image should be around 3-4GB.
Edit: make sure that You have newest odin and proper firmware for Your phone.
ProtoDeVNan0 said:
Sorry. I was busy.
Okay!
Tap on AP in odin and add Home image and then tap on start. Home image should be around 3-4GB.
Edit: make sure that You have newest odin and proper firmware for Your phone.
Click to expand...
Click to collapse
Thanks again. I did try uploading all four files. AP, BL, CP and Home CSC.
So after tapping on AP i should add AP file right which is 4.2 GB? Didnt get any home image file.
Sorry for the silly questions. I am a complete noob in all this.
Update: Finally managed to restore via smartswitch. Thank you everyone
Chirag22ster said:
Thanks again. I did try uploading all four files. AP, BL, CP and Home CSC.
So after tapping on AP i should add AP file right which is 4.2 GB? Didnt get any home image file.
Sorry for the silly questions. I am a complete noob in all this.
Update: Finally managed to restore via smartswitch. Thank you everyone
Click to expand...
Click to collapse
I'm happy You fixed it .
Just in case if You'll need extra help later. (Or anyone else)
Inside the zip file that You download from sammobile should be couple of files. One of them should be named Home_something.tar.md5 - this one goes to AP.
Then You should press start and let it do its work. But if Smartswitch works for You then no need to worry.
Just to inform you if there is a next time, try another USB port and/or a different USB cable (ie. the original one)
same issue
i have pretty much the same issue but mine is stuck via a bad rom. the problem I have now is my computer will not recognize it when I plug into usb. any ideas?
Hi,
I just bought a tablet Samsung Galaxy A SM-T510 and when I run it, Android ask the last Google Account that was in it.
I searched a lot in this forum but I'm not sure to understand all the way to remove this verification.
I'm new here... Somebody could explain me the way to remove it ?
It's impossible to run Android without this email. I do not have access to the system configuration.
When I look for the Android Recovery, my version is T510XXU1ASEF XEF. I already tried to install a new firmware (I succeded and I was thinking it would be enough but it wasn't).
Big thank you for your help.
Search for SM-T510 FRP lock.
lewmur said:
Search for SM-T510 FRP lock.
Click to expand...
Click to collapse
Thank you for your answer.
Already look for this. I find no solution. Some method tell to install combination file to remove the Google Verification, but I've everytime a Fail in Odin.
Desktructor said:
Thank you for your answer.
Already look for this. I find no solution. Some method tell to install combination file to remove the Google Verification, but I've everytime a Fail in Odin.
Click to expand...
Click to collapse
You must be doing something wrong. That's is the solution that works and it is the ONLY solution. If you can't get it to work, you got a brick.
edit: Make sure you have the combo files for the T510 and not some other model.
lewmur said:
You must be doing something wrong. That's is the solution that works and it is the ONLY solution. If you can't get it to work, you got a brick.
Click to expand...
Click to collapse
Ok...
My way :
- Recovery mode
- Wipe data/factory reset. Same for cache
- Reboot to BootLoader
- Launch Odin V3.13.1 like administrator
- Connect the tablet to PC
- Put the combination file into AP... Look that "Auto Reboot" and "F Reset Time" is checked.
- "Start".
It's good until there ?
Ty for your answer.
Desktructor said:
Ok...
My way :
- Recovery mode
- Wipe data/factory reset. Same for cache
- Reboot to BootLoader
- Launch Odin V3.13.1 like administrator
- Connect the tablet to PC
- Put the combination file into AP... Look that "Auto Reboot" and "F Reset Time" is checked.
- "Start".
It's good until there ?
Ty for your answer.
Click to expand...
Click to collapse
You have to be in "Download" mode to use Odin. And there are two steps in using the two combo files. I don't you recall the exact steps but they are in the instructions.
lewmur said:
You have to be in "Download" mode to use Odin. And there are two steps in using the two combo files. I don't you recall the exact steps but they are in the instructions.
Click to expand...
Click to collapse
When I choose the option "Reboot to bootloader", I've a blue screen with "Downloading". This is not this way ?
When I connect the tablet to PC, Odin recognize it.
Desktructor said:
When I choose the option "Reboot to bootloader", I've a blue screen with "Downloading". This is not this way ?
When I connect the tablet to PC, Odin recognize it.
Click to expand...
Click to collapse
My tablet is a T580 and the download screen is green. But if Odin show "added" when you plug it into the PC, then it should work. You still have to proceed with the combo files as instructed.
lewmur said:
My tablet is a T580 and the download screen is green. But if Odin show "added" when you plug it into the PC, then it should work. You still have to proceed with the combo files as instructed.
Click to expand...
Click to collapse
Then ! I was not in download mode... For the download mode, you need to:
- Power off the tablet
- Press up and down
- Connect cable to Odin
- A blue screen appaers, press up to confirm
- You're in downloading mode.
Btw, I tried with the combination file that I downloaded yesterday, and I've one fail in Odin with this log:
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1492 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Can't open the specified file. (Line: 1892)
<OSM> All threads completed. (succeed 0 / failed 1)
I check "re-partition" and "F Reset Time".
I'm I in the good way ?
The combination File is good for my version od firmware ?
COMBINATION_FAC_FA90_T510XXU1ASC4_PakFirmware
Combinatio file : COMBINATION_FAC_FA90_T510XXU1ASC4_FACFA90_T510FAC1ASC4_CL15541918_QB22647847_REV02_user_mid_noship.tar.md5
Version tablet : T510XXU1ASEF
Ty so much for your help.
Desktructor said:
Then ! I was not in download mode... For the download mode, you need to:
- Power off the tablet
- Press up and down
- Connect cable to Odin
- A blue screen appaers, press up to confirm
- You're in downloading mode.
Btw, I tried with the combination file that I downloaded yesterday, and I've one fail in Odin with this log:
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1492 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Can't open the specified file. (Line: 1892)
<OSM> All threads completed. (succeed 0 / failed 1)
I check "re-partition" and "F Reset Time".
I'm I in the good way ?
The combination File is good for my version od firmware ?
COMBINATION_FAC_FA90_T510XXU1ASC4_PakFirmware
Combinatio file : COMBINATION_FAC_FA90_T510XXU1ASC4_FACFA90_T510FAC1ASC4_CL15541918_QB22647847_REV02_user_mid_noship.tar.md5
Version tablet : T510XXU1ASEF
Ty so much for your help.
Click to expand...
Click to collapse
You can't just use Odin on the combo file. That file must first be extracted to find the TWO files needed for Odin. Then you use Odin on one file first and then let the tablet reboot. Then go back into download and use Odin for the other file. I don't recall which file goes first but the instruction should be in the post where you found the file you downloaded.
lewmur said:
You can't just use Odin on the combo file. That file must first be extracted to find the TWO files needed for Odin. Then you use Odin on one file first and then let the tablet reboot. Then go back into download and use Odin for the other file. I don't recall which file goes first but the instruction should be in the post where you found the file you downloaded.
Click to expand...
Click to collapse
When I extract the .rar, I've only only file that end with ".tar.md5"... I've only one file in the archive. I need to extract this ".tar.md5"? How can I do that?
Desktructor said:
When I extract the .rar, I've only only file that end with ".tar.md5"... I've only one file in the archive. I need to extract this ".tar.md5"? How can I do that?
Click to expand...
Click to collapse
You don't. md5 files are what you use in Odin. Again, not owning a T510, I don't know the exact process for it. For the T580, it is a two stage process. Maybe for the T510, you just use Odin on the one md5 file you extracted. Any further assistance will have to come from someone who has done it on the T510.
edit: BTW, you probably shouldn't check "re-partition" unless you are flashing a PIT file.
lewmur said:
You don't. md5 files are what you use in Odin. Again, not owning a T510, I don't know the exact process for it. For the T580, it is a two stage process. Maybe for the T510, you just use Odin on the one md5 file you extracted. Any further assistance will have to come from someone who has done it on the T510.
edit: BTW, you probably shouldn't check "re-partition" unless you are flashing a PIT file.
Click to expand...
Click to collapse
Ty for you help.
It's probably different between those two model.
I tried all way to flash correctly, I tried to download again other version of "combination file" to turn fail in success, but nothing works.
I searched for hours how to FRP unlock... Nobody have idea about my problem ?
When I'm in Downloading mode, I can see in the top left :
ODIN MODE
DOWNLOAD SPEED : FAST
PRODUCT NAME : SM-T510
CURRENT BINARY : Samsung Official
KG STATE : Prenormal
FRP LOCK : ON
OEM LOCK : ON(L)
Secure Download : Enabled
CCIC = S2MM005 hw: 7 boot: 8 main4a
CARRIER_ID:
WARRANTY VOID: 0 (0x0000)
RP SWREV B: 1 K: 1 S: 1
DID = 44d7f75a222c
Do I have to change something there or this is correct ?
For information, I can't change OEM cuzz I don't have access to system.
Yes, do not check the re partition. You are not partitioning the device. Flashing a combination file is the same on both the T580 and the T510. However, you should have 4 files to flash not just one. You should have a BL, AP and the CSC with the HOME CSC files. Put each one in their respective places. All files being used by Odin3 must be in "tar.md5" form. You do not have to plug in the USB cord to get the device into Download mode but you have to plug it in to flash it. You will get a blue connected section when you do.
Then apparently you are trying to get past the FRP lock. There are a variety of methods to remove the Google Account FRP lock on You Tube but this is the one you probably are looking for.
https://www.youtube.com/watch?v=gW1IdBaG6MY
Desktructor said:
Then ! I was not in download mode... For the download mode, you need to:
- Power off the tablet
- Press up and down
- Connect cable to Odin
- A blue screen appaers, press up to confirm
- You're in downloading mode.
Btw, I tried with the combination file that I downloaded yesterday, and I've one fail in Odin with this log:
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1492 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Can't open the specified file. (Line: 1892)
<OSM> All threads completed. (succeed 0 / failed 1)
I check "re-partition" and "F Reset Time".
I'm I in the good way ?
The combination File is good for my version od firmware ?
COMBINATION_FAC_FA90_T510XXU1ASC4_PakFirmware
Combinatio file : COMBINATION_FAC_FA90_T510XXU1ASC4_FACFA90_T510FAC1ASC4_CL15541918_QB22647847_REV02_user_mid_noship.tar.md5
Version tablet : T510XXU1ASEF
Ty so much for your help.
Click to expand...
Click to collapse
Don't check re-partition. That will re-partition the whole device, and ruin it. Was this device brand new or used??
secretwolf98 said:
Don't check re-partition. That will re-partition the whole device, and ruin it. Was this device brand new or used??
Click to expand...
Click to collapse
He cant flash combo without a factory token as it needs approval now.. same as most all other new samsung devices are. The approval error displays on the phone itself once the flash fails in odin.
elliwigy said:
He cant flash combo without a factory token as it needs approval now.. same as most all other new samsung devices are. The approval error displays on the phone itself once the flash fails in odin.
Click to expand...
Click to collapse
How do you obtain a factory token? If your tablet was bought from a legit seller on eBay, can you get one from Samsung? How do you use it?
lewmur said:
How do you obtain a factory token? If your tablet was bought from a legit seller on eBay, can you get one from Samsung? How do you use it?
Click to expand...
Click to collapse
Try calling Samsung for support. Explain your issue. Their number is: (1-800-SAMSUNG)
secretwolf98 said:
Try calling Samsung for support. Explain your issue. Their number is: (1-800-SAMSUNG)
Click to expand...
Click to collapse
I contacted Samsung which wouldn't help because I bought mine from EBay. Unaurthorized reseller was what I was told and they couldn't help me. So I scoured through You Tube videos and found nothing that will help unless the device had a SIM card which it doesn't. Sooner or later someone will get past this FRP account lock and we can use our tablets. In the meantime I'll experiment with it.
Casper Young said:
I contacted Samsung which wouldn't help because I bought mine from EBay. Unaurthorized reseller was what I was told and they couldn't help me. So I scoured through You Tube videos and found nothing that will help unless the device had a SIM card which it doesn't. Sooner or later someone will get past this FRP account lock and we can use our tablets. In the meantime I'll experiment with it.
Click to expand...
Click to collapse
I just received my SM-T720 back from Samsung and I purchased on eBay. Had to have eBay (not the seller) send me a proof of purchase email to do it, but it was accepted. Probably depends on how helpful the person who handles your call wants to be. If I were you, I'd contact eBay and get a proof of purchase from them, and then try Samsung again.:fingers-crossed:
edit: As I recall, I did have to get fairly persistent before the rep agreed to help.:crying: