Related
I've tried the "brick fixes" on this forum, but without luck so far... I can get into download mode, and I've tried flashing with odin from this post which says "passed" to me. After this is reboots into a black screen after the "galaxy S" screen, and nothing can be done except making the capasitive buttons light up...
All help is appreciated!!
FYI I don't have a SD card installed during odin...
Solutions in #6 and #7...
Thanks a ton
Novek said:
I've tried the "brick fixes" on this forum, but without luck so far... I can get into download mode, and I've tried flashing with odin from this post which says "passed" to me. After this is reboots into a black screen after the "galaxy S" screen, and nothing can be done except making the capasitive buttons light up...
All help is appreciated!!
FYI I don't have a SD card installed during odin...
Click to expand...
Click to collapse
Sounds like a boot loop, but I can't figure out why you would get one with the stock odin flash. Try doing a factory reset? it shouldn't be needed, but who knows?
how? tried the "hard reset" whitout luck
Novek said:
how? tried the "hard reset" whitout luck
Click to expand...
Click to collapse
In recovery.. there should be a factory reset option. I thought odin did that though.
when it is resetting I can read "mbr checksum error" or similar in yellow text before it's wiping data etc...
Try this ...turn you phone off but keep it plugged into you cpu usb cord and open oidin, next put your phone in download mode and put the needed files in oden and click start I had a hard time getting odin to work right for some reason this may not help but it worked for me. Good luck I don't think you bricked I think you can come out of this.
I assume that you used the partition in ROM Manager? If so I had the same problem as you. The phone would boot up to a black screen with only the buttons working. What I did was flash Eugenes 2.2 Froyo Rom, I surprised that it booted up and worked. After that I flashed back to stock rom and it work as it did before!
AustinKnight45 said:
Try this ...turn you phone off but keep it plugged into you cpu usb cord and open oidin, next put your phone in download mode and put the needed files in oden and click start I had a hard time getting odin to work right for some reason this may not help but it worked for me. Good luck I don't think you bricked I think you can come out of this.
Click to expand...
Click to collapse
Thanks for the help, but my problem occurs after odin... when it's rebooting and it says "passed!" i just end up with a black screen with only the capasitive buttons lighting up when pressed...
ElahC said:
I assume that you used the partition in ROM Manager? If so I had the same problem as you. The phone would boot up to a black screen with only the buttons working. What I did was flash Eugenes 2.2 Froyo Rom, I surprised that it booted up and worked. After that I flashed back to stock rom and it work as it did before!
Click to expand...
Click to collapse
that's my problem!! found it, downloading now... will report back for future accidents...
Froyo worked!! Thanks a ton! Now I just have to downgrade
sry... dubbel
I HAVE THE SAME PROBLEM. How did you get odin to detect your phone? I put it into download mode but no detection plzzz help
farrisizdaman said:
I HAVE THE SAME PROBLEM. How did you get odin to detect your phone? I put it into download mode but no detection plzzz help
Click to expand...
Click to collapse
I turned the phone off while the usb was connected when the phone if off open odin ounce its open boot up the phone and boot it into download mode from there odin will connect and you can put the files you need into it and click start. This worked well for me when I needed to revert back to factory vibrant after flashing the "Real lag FIX" kernel that made my ear piece not work and some of my buttons not work but boy was my phone snappy and my benchmarks were awesome but what good does that do when your girl calls you and you cant hear her and all she can hear is you saying hellllllllooooooo .
I"ve been trying to flash with odin now for about 2 hours. It gets stuck on DO NOT DISCONNECT. And never finishes.
farrisizdaman said:
I"ve been trying to flash with odin now for about 2 hours. It gets stuck on DO NOT DISCONNECT. And never finishes.
Click to expand...
Click to collapse
Ya it was like that for me until I did what I said in my last post, you do have the samsung drivers installed ?
Edit: And you are using this method or this thread HERE
farrisizdaman said:
I"ve been trying to flash with odin now for about 2 hours. It gets stuck on DO NOT DISCONNECT. And never finishes.
Click to expand...
Click to collapse
You have managed to get into download mode right? My device is up and running stock now, but gonna try some other ROM now =)
Glad to hear your phone is back up and running .
i know this is an old thread, but i figure this can help someone later... brick is a common search term, and i figure this will come up in a search and this will save time for others...
here's what happened to me. i was flashing back to stock and was in download mode. the blue bar was moving etc and murphy and his dumb law decided to kill my my usb port... i thought the phone was DEAD! nothing i did woke the phone up. no battery indicator, buttons didn't do anything... it was all black. holding up/down and power didnt turn the phone on and into recovery or download mode... the phone was DEAD...
then after scouring the forum forever, i finally got the phone into download mode...
NOTE: i don't recall if the usb wire was plugged into the computer or not... i think it was though...
NOTE2: samsung drivers should have been installed already...
- remove the battery
- hold vol up and vol down buttons
- reinsert battery
i thought WOO HOO!! I GOT INTO DOWNLOAD MODE!!!
the next issue i had was getting odin to recognize the phone... it didn't detect what com port i had. but after a lot of reading, i finally got it to work...
- open odin first
- then get into download mode using the steps above...
after odin recognized the port the phone was plugged into, i flashed back to stock rom using the instructions given on this site... and my dead phone works again...
i was able to fix a dead phone!! this phone could be un-brickable!!
i hope this helps...
farrisizdaman said:
I HAVE THE SAME PROBLEM. How did you get odin to detect your phone? I put it into download mode but no detection plzzz help
Click to expand...
Click to collapse
Open odin first, then plug in your phone.
I somehow lost the backup of my premangostate after updating to mango. I'm having issues with my device overheating and I need to mail it in to AT&T. But doesn't the Mango beta technically void your warranty? If it does, I need to revert to premango in order to send it in... what should I do? I've tried everything. I downloaded a ROM but I don't know how to use it! HELP!!
eaglesfreak53 said:
I somehow lost the backup of my premangostate after updating to mango. I'm having issues with my device overheating and I need to mail it in to AT&T. But doesn't the Mango beta technically void your warranty? If it does, I need to revert to premango in order to send it in... what should I do? I've tried everything. I downloaded a ROM but I don't know how to use it! HELP!!
Click to expand...
Click to collapse
It does void it. Flash UCJK2 ROM from here. Just tell them you didn't update.
EnderPsp said:
It does void it. Flash UCJK2 ROM from here. Just tell them you didn't update.
Click to expand...
Click to collapse
Do you think you could post a step by step of what to do? I tried going through the forum you suggested but had no luck following the steps. I'm a US AT&T customer.
eaglesfreak53 said:
Do you think you could post a step by step of what to do? I tried going through the forum you suggested but had no luck following the steps. I'm a US AT&T customer.
Click to expand...
Click to collapse
There isn't one for Focus but if you follow the step by step guide for Omnia 7 with the Focus Rom, you should be okay as it's exactly the same. Just use the Focus UCJK2 Rom instead of the Omnia7 one.
Here's the short version:
You will not need the "Samsung WP7 Flash Program" as it is included in the ROM (Samsung-i917-Focus-firmware-UCJK2-ATT-USA.exe).
Install Samsung Mobile USB Drivers v5.2
Put the phone in download mode. Make sure battery is at least 80% when you do.
Turn off the phone
Turn on the phone, holding down the Power + Volume UP + Camera buttons simultaneously.
When the phone turns on, release the power button.
A yellow triangle with an exclamation mark and a "download mode” message should appear.
(there are 2 ways to get out of this mode: flash a rom or remove the battery).
1. Copy "Samsung-i917-Focus-firmware-UCJK2-ATT-USA.exe" in a new folder and run it (Install). After running you will see these files:
signed_CSC_Cetus_ATT_i917ATTJK2.csc
signed_eboot_Cetus_ATT.eb0
signed_pda_Cetus_ATT.nb0
signed_phone_Cetus_ATT.bin
WP7 Downloader Ver 7.21 for All Device (Publish version).exe
WP7_Downloader_Ver_7.05_for_Retail_Device_(Product_Force_Select_MD5_X).exe
The fhash program you need to run is
WP7_Downloader_Ver_7.05_for_Retail_Device_(Product_Force_Select_MD5_X).exe
2. Run it and load in it the files in this folder (click Phone, Eboot, PDA, CSC)
3. If the port isn't green, disconnect the phone from USB and reconnect.
You should be good to go with all this.
eaglesfreak53 said:
Do you think you could post a step by step of what to do? I tried going through the forum you suggested but had no luck following the steps. I'm a US AT&T customer.
Click to expand...
Click to collapse
I'll be reflashing my Rogers Samsung Focus yet again since I've been trying to change MMS settings so it will work with FIDO. Anyway, I'll be reflashing this weekend. PM me if you want some walk through steps.
[Q]Restoring backup after flashing rom
Hi,
I have a At&t samsung focus running 8107 and phone's power button started acting weird. If i press it nothing happen at first, then the slide down to power off appear. I would press back but it would shut off anyways. It wouldn't reboot right and usually took about 20 tries to boot it. I have two backups saved one mango beta and one for current version. The problem got worse (wouldn't boot at all unless on usb power) so i restored it to my current version backup. Everything worked but after a week the problem came back and the phone was dead. I decided to flash it to factory rom (had problems getting it to boot to rebuild) but I eventually got it to boot. The power button still did nothing. I updated it back to 8107 and tried to restore to my backup. I keep getting error code 801812E0. My question is do you have to use the same update path to restore a backup? I had the mango beta, refresh, then cleanup to get to 7720 Mango build. The second time around I used official update path. Do you think this is hardware related?
Thanks in advance
From your description, it sounds like your power button is getting stuck in the pressed position. "Always Pressed". Occasionally, when messing with it, it will release. Also, when plugged in, that forces it to start up.
Try cleaning around the button, or remove any cases/screen protectors that might be sticking it down. If that does not work, you might need to take apart to clean or replace the button. Only attempt if you are comfortable with that type of job, otherwise, send in for repair.
Thanks for the quick response. I will try that.
Also would the power button being stuck affect the hard reset menu and download mode? I can still access download mode but the hard reset menu disappears after about 10 seconds. The only way I can reboot the phone is to plug into USB power via computer and touch the metal springs where the battery connects with a tweezers.
xyzyzyxx99 said:
Also would the power button being stuck affect the hard reset menu and download mode? I can still access download mode but the hard reset menu disappears after about 10 seconds.
Click to expand...
Click to collapse
Yes. If you hold the power button in Any mode, it forces a shutdown after a few seconds.
Took the phone apart and cleaned around the button. Still won't boot, is it possible the phone's drivers to communicate with the power button are bad? And any idea why my backups failed to restore after flashing the rom?
xyzyzyxx99 said:
Took the phone apart and cleaned around the button. Still won't boot, is it possible the phone's drivers to communicate with the power button are bad? And any idea why my backups failed to restore after flashing the rom?
Click to expand...
Click to collapse
I think this has gotten off topic from the original thread. I'll send you a private message, and we can continue there. I've been around a while, so I might get into trouble keeping it going here, since I should know better.
Does anyone have a working link to download the Samsung Focus USB drivers?
All the multiupload links are down and i am stuck with a bricked phone.
Mirror or alternate link appreciated..
Thanks
NilayS said:
Does anyone have a working link to download the Samsung Focus USB drivers?
All the multiupload links are down and i am stuck with a bricked phone.
Mirror or alternate link appreciated..
Thanks
Click to expand...
Click to collapse
Download Samsung drivers from here.
Can I get the long version of flashing a Focus I917. Yes noob, if by chance there are some pics would be helpful also! Thanks in advance!
SteelLife said:
Can I get the long version of flashing a Focus I917. Yes noob, if by chance there are some pics would be helpful also! Thanks in advance!
Click to expand...
Click to collapse
Follow this post.
As i have too little posts, i cannot post to the appropriate thread. Hopefully someone who knows something of these devices sees this and can help...
Fiddled with my phone and tried to update to 7720 but updating failed and phone stuck totally in "LG" boot logo.
As a last resort, decided to upgrade the firmware to EUR Open. Everything goes quite smoothly until 100% when the app tries to reset and restart the phone. Phone gets stuck again in "LG" boot logo and after a while the upgrading app gives me a notice "errnum6 open port". Cannot avoid that no matter what i do.
Help, anyone?
First, make sure you're flashing to a compatible firmware (i.e., E900h firmware for an E900h device). If your EmergencyDownload mode is still functional, try flashing again, but from a different computer and using a different microUSB cable.
Thanks Arktronic. What should happen when the app resets the phone (in 100%)? Should the phone boot up normally or does it still need a lot of time to initialize?
tkay564 said:
Thanks Arktronic. What should happen when the app resets the phone (in 100%)? Should the phone boot up normally or does it still need a lot of time to initialize?
Click to expand...
Click to collapse
I don't know about your case but when I was upgrading from 7712 to 7720 the reboot stage took me over 10minutes to complete.
Yes, it might take up to 10 minutes to re-initialize. Much more than that probably means an actual brick.
Thanks for the tips. Nothing helped though and finally had to give up. Tried with two different firmwares (eur and german), computers and cables but phone could not boot up after reset. Well, you can't always win...
At least the phone starts in Emergency Download mode? (camera, volume down and then power)
My Telus Optimus 7 does this as well now. I had issues with it after restoring my NoDo backup from Mango RTM. It worked for a while, and started rebooting to a "storage card not working" error; I could usually reboot it and get it to work for a while, but at one point, no matter how many times I rebooted I could not get it to go past that message. Thought I'd flash the firmware using the instructions here, and I get exactly the same issues as tkay564. It seems like it flashes the Telus (Canada) ROM fine, until the reset phase, then it keeps rebooting the phone endlessly, never going past the LG logo. LGDP2 gives me the ErrNum6 error as well. I've tried with the Mexican ROM, did not work either.
The best I can do is reflash the phone as yes, the Emergency Download mode still works. Not that it's doing me much good.
Unfortunately, sending back the phone is going to be tricky, as I bought the phone second-hand...
---
*EDIT: I've also checked the logs for the LGDP2 tool after flashing; it also reports everything as normal until it tries restarting. I'm also pursuing RMA with LG, hopefully they'll take it.
the.rider1290 said:
At least the phone starts in Emergency Download mode? (camera, volume down and then power)
Click to expand...
Click to collapse
Yep it does (or did..) so pushing in a new firmware is not an issue. But getting it to boot up afterwards is..
it sounds like an hardware issue (me too I was able to flash fimrware but stuck on LG logo, they replaces the motherboard)
the.rider1290 said:
it sounds like an hardware issue (me too I was able to flash fimrware but stuck on LG logo, they replaces the motherboard)
Click to expand...
Click to collapse
Got it back today. Motherboard was replaced.
Hey Everyone, just got my G2 today and already have a problem. So naturally the first thing I did was root it, and after a few hours researching the nuances of doing that on a VZW model I got that to work. Next I went and downloaded Titanium and moved my backup files onto the phone, and restored my apps no problem. Then I went to restore my system info (just call logs, sms/mms, bluetooth pairings) and rebooted the phone only to get stuck in a bootloop (the VZW animation would just play over and over.) So I powered off the phone thinking something just went wrong with the reboot. When I went to turn it back on I started to get worried...
No matter what key combo I pressed I could not get the phone to power on. I decided to plug it in and thankfully it did come back on, but once again went into the bootloop. So I did some researching and tried every way to reflash the stock VZW firmware, but nothing has worked. I tried the KDZ method mentioned here, but I cannot get the B2CAppSetup.exe program to install (looks like LG has moved or revoked access to csmg.lgmobile.com:9002). So I moved to this post, but I cannot get the LG Flash Tool to start the flashing (when as instructed I unplug the phone and restart it in download mode again and plug it back in the Flash Tool just says "Waiting for Connection" and doesn't do anything.)
At this point I am out of ideas. I have a feeling that since I cannot even power the phone on unless its connected to USB/Power Adapter something is seriously wrong, but I have no idea what Titanium could have restored to cause this.
Any ideas or suggestions would be greatly appreciated.
Did the same thing myself and nearly crapped myself. Here's how I got out of it:
Power down the phone (hold down power button)
Turn on phone by holding power & volume down buttons
When the LG screen comes up, let go of the buttons and then hold them down again
You should then get options to factory reset.
I will say this, I was never able to restore SMS or call logs from Titanium. Doing a few factory resets just made me stop caring.
Thanks for the reply, however no matter what key combo I press I cannot get the phone to power on unless it is plugged into USB/Power Adapter so I cannot get into the stock recovery app.
Any other ideas guys?
TRDeal195 said:
Thanks for the reply, however no matter what key combo I press I cannot get the phone to power on unless it is plugged into USB/Power Adapter so I cannot get into the stock recovery app.
Any other ideas guys?
Click to expand...
Click to collapse
This happened to me while flashing as well.
You have to keep trying, the timing of exactly when to release the buttons and press them again is very precise, meaning you don't have much time at all.
It took me several tries to get it back to recovery.
I also only released just the power button, not both,
Good Luck!
drice72 said:
This happened to me while flashing as well.
You have to keep trying, the timing of exactly when to release the buttons and press them again is very precise, meaning you don't have much time at all.
It took me several tries to get it back to recovery.
I also only released just the power button, not both,
Good Luck!
Click to expand...
Click to collapse
Where you able to power your phone up by just pressing the power button (without it connected to anything)? That's what keeps throwing me off about this whole thing, without connecting it to something no matter what button(s) I press the phone simply will not do anything.
When you plug in the device via USB and hold the vol+key you should get the same prompt for a factory reset...
Cyko.Tech67 said:
When you plug in the device via USB and hold the vol+key you should get the same prompt for a factory reset...
Click to expand...
Click to collapse
When I do this the only thing that happens is a small message comes up saying "Download Mode" and then the phone immediately goes to the firmware update screen....
TRDeal195 said:
When I do this the only thing that happens is a small message comes up saying "Download Mode" and then the phone immediately goes to the firmware update screen....
Click to expand...
Click to collapse
were you running a custom rom?
or stock LG
Cyko.Tech67 said:
were you running a custom rom?
or stock LG
Click to expand...
Click to collapse
Stock VS98011A_01 rooted via IORoot.
TRDeal195 said:
Stock VS98011A_01 rooted via IORoot.
Click to expand...
Click to collapse
Here is my suggestion to you... try and push twrp recovery to your phone, theres a change you adb bridge might still be working, then id try flashing a rom once done with that... i can get you a link for the method on pushing twrp using the iOroot folder... will edit this in a min. once i find it
________________________________________________________________
Heres that link : http://forum.xda-developers.com/showthread.php?t=2449670
________________________________________________________________
if your having any troubles pushing twrp let me know
Cyko.Tech67 said:
Here is my suggestion to you... try and push twrp recovery to your phone, theres a change you adb bridge might still be working, then id try flashing a rom once done with that... i can get you a link for the method on pushing twrp using the iOroot folder... will edit this in a min. once i find it
________________________________________________________________
Heres that link : http://forum.xda-developers.com/showthread.php?t=2449670
________________________________________________________________
if your having any troubles pushing twrp let me know
Click to expand...
Click to collapse
Thanks for the suggestion! I'll give this a shot now and let you know how I make out.
TRDeal195 said:
Thanks for the suggestion! I'll give this a shot now and let you know how I make out.
Click to expand...
Click to collapse
please do!
So I tried TWRP but ADB could not see the phone. As a last resort I tried the TOT restore method on the computer that I used to root it initially and it actually went through. Once 10B was restored it finally booted back up and OTA'd 11A and I was able to re-root it after that.
Lesson learned, next time I will not try to recover the phone using a difference laptop then I rooted it on.
Thanks for the help and suggestions guys!
TRDeal195 said:
So I tried TWRP but ADB could not see the phone. As a last resort I tried the TOT restore method on the computer that I used to root it initially and it actually went through. Once 10B was restored it finally booted back up and OTA'd 11A and I was able to re-root it after that.
Lesson learned, next time I will not try to recover the phone using a difference laptop then I rooted it on.
Thanks for the help and suggestions guys!
Click to expand...
Click to collapse
Happy to hear you got it fixed! Now that you have got it working agian, your adb bridge should be working! so i would save that link in case of wanting to rom in the future! Hope i helped you!
Saturday evening I got a notification saying 5.0 lollipop was available for my s5 so I eagerly downloaded the update. During the update my phone froze and crashed (had this happen twice earlier in the day) and it rebooted to the update screen. Once the update finished installing the phone rebooted like normal and sat at the verizon screen for about 2 minutes before crashing again. This caused the phone to enter a boot loop that ended up making an open padlock symbol appear on the start screen. After this appeared it took me to a screen that said "System software not authorized by Verizon has been found on your phone". After getting this error I tried using Odin and Kies to reinstall 4.4 on my device. The install was successful but after the phone booted it was freeze and crash again leading to another boot loop and a "recovery booting" message in the top left screen. It now either boots back to the System software screen or loops until it hits the recovery menu. Is there any way to fix this or did Verizon brick my phone?
koerng said:
Saturday evening I got a notification saying 5.0 lollipop was available for my s5 so I eagerly downloaded the update. During the update my phone froze and crashed (had this happen twice earlier in the day) and it rebooted to the update screen. Once the update finished installing the phone rebooted like normal and sat at the verizon screen for about 2 minutes before crashing again. This caused the phone to enter a boot loop that ended up making an open padlock symbol appear on the start screen. After this appeared it took me to a screen that said "System software not authorized by Verizon has been found on your phone". After getting this error I tried using Odin and Kies to reinstall 4.4 on my device. The install was successful but after the phone booted it was freeze and crash again leading to another boot loop and a "recovery booting" message in the top left screen. It now either boots back to the System software screen or loops until it hits the recovery menu. Is there any way to fix this or did Verizon brick my phone?
Click to expand...
Click to collapse
Try doing a wipe and then factory reset from recovery mode.
Rapunzl said:
Try doing a wipe and then factory reset from recovery mode.
Click to expand...
Click to collapse
Still boots with the custom rom padlock and freezes on the verizon screen
Try pulling the battery. I've read where that's helped some people get it to boot.
newmanx4 said:
Try pulling the battery. I've read where that's helped some people get it to boot.
Click to expand...
Click to collapse
I've got to pull it when it freezes, I think the problem is that its reading it as a rooted rom even though its not
Same problem
koerng said:
Saturday evening I got a notification saying 5.0 lollipop was available for my s5 so I eagerly downloaded the update. During the update my phone froze and crashed (had this happen twice earlier in the day) and it rebooted to the update screen. Once the update finished installing the phone rebooted like normal and sat at the verizon screen for about 2 minutes before crashing again. This caused the phone to enter a boot loop that ended up making an open padlock symbol appear on the start screen. After this appeared it took me to a screen that said "System software not authorized by Verizon has been found on your phone". After getting this error I tried using Odin and Kies to reinstall 4.4 on my device. The install was successful but after the phone booted it was freeze and crash again leading to another boot loop and a "recovery booting" message in the top left screen. It now either boots back to the System software screen or loops until it hits the recovery menu. Is there any way to fix this or did Verizon brick my phone?
Click to expand...
Click to collapse
I am having the EXACT same issue. I need to something up and going. Any help here would be appreciated.
BryceRuss said:
I am having the EXACT same issue. I need to something up and going. Any help here would be appreciated.
Click to expand...
Click to collapse
Have you tried talking to verizon yet? I'm gonna take my phone down to the store tomorrow and see if theres anything they can do.
koerng said:
Have you tried talking to verizon yet? I'm gonna take my phone down to the store tomorrow and see if theres anything they can do.
Click to expand...
Click to collapse
Ok, so I am safe now. I was able to flash a stock NK2 Kernal.
Pull the battery on the phone. Hold down Vol. Down, Home, and Power and go to download mode. Plug in the phone, and open Odin. Flash the kernal.
Reboot and you should be ok. This just worked for me.
BryceRuss said:
Ok, so I am safe now. I was able to flash a stock NK2 Kernal.
Pull the battery on the phone. Hold down Vol. Down, Home, and Power and go to download mode. Plug in the phone, and open Odin. Flash the kernal.
Reboot and you should be ok. This just worked for me.
Click to expand...
Click to collapse
I tried flashing the kernel, it booted and I got an error that said "processing system isn't responding" and it crashed back to the verizozn software screen.
koerng said:
I tried flashing the kernel, it booted and I got an error that said "processing system isn't responding" and it crashed back to the verizozn software screen.
Click to expand...
Click to collapse
If Kies doesn't work, try Verizon Update Tool. It also has a repair tab and may help you get back to stock.
Rapunzl said:
If Kies doesn't work, try Verizon Update Tool. It also has a repair tab and may help you get back to stock.
Click to expand...
Click to collapse
The verizon tool won't even recognize my phone
koerng said:
The verizon tool won't even recognize my phone
Click to expand...
Click to collapse
Instead of flashing only the kernel, flash a stock, unrooted retail version of KK 4.4.4.
BryceRuss said:
Ok, so I am safe now. I was able to flash a stock NK2 Kernal.
Pull the battery on the phone. Hold down Vol. Down, Home, and Power and go to download mode. Plug in the phone, and open Odin. Flash the kernal.
Reboot and you should be ok. This just worked for me.
Click to expand...
Click to collapse
This worked for me as well, thanks! For anyone that wants to know, I used "NK2_Stock_Restore.tar.md5" specifically. You can get it from this thread labeled as "NK2 Stock Restore".