Database Users

I think I bricked my ppc 6700

I wuz flashing it went to 99% and gave me an error so I reset and it wuz still stuck so I took out the battery and now it won't do anything when I plug it into the pc it says unrecognized usb device is there anyway to get the pc to recognize it so I can fix it any help is appreciated

bootloader
Put it into the bootloader, the PC wont recognize the device until you flash it again, but you should be able to fix it. Get into the bootloader by pressing the power key and the voice commander button (looks like an old tape) at the same time and while holding, press the soft reset button on the bottom. This should put you into the bootloader mode, (the backlight does not light up, it just says bootloader and USB or SERIAL in faint writing depending if you have it attached to your PC)

invoking boot loader
Yes...I had a similar issue yesterday and thought to use the button sequence to force the bootloader. The other thing I had to do was get a flashlight and note the bootloader version of 2.05. I then ran the latest update tool from one of the kitchens and that allowed me to load the image of choice that I placed in the same folder.

how did you do it?

I used UNI_bootloader EXIT.exe to get mine back. same situation, v2.05 bootloader, unplugged at 99%. stuck at v2.05. run the exe, and its fine.

Sadly enough i need to post this.. i have both the 6800 and the 6700, i did the same thing twice ... starting with the 6800, had no problem fixing that one, but the 6700 for some reason after a stock rom flash that didnt take completely its stuck saying Serial (top), 1.00 (bottom) , tried uni_bootloader, tried reflashing, for some reason it cannot catch the device, however, the drivers are loaded just fine, that much i know it worked before. any ideas on how to kick start this thing ( i have no memory card at all in it , havent been able to find a miniSD around here anywhere ). Any ideas would greatly help. Thanks in advance.

[Q] Tattoo Bricked

Hello,
I tried to update the radio and the SPL version on my Tattoo. Everything went fine until I had to reboot my phone. It shut down alright, but it never powered on again.
These are the following problems I am having with my Tattoo at the moment:
Cannot power on phone.
Cannot boot into recovery mode.
Cannot boot into FastBoot.
When I connect it to my computer via USB, nothing happens.
The only thing that it's responding to is when I connect my it to my charger.
Does anyone have a solution or is my phone dead forever?
Thanks ahead!

bump? anyone?

Send it back to HTC. If anyone can do anything about it they can. There's nothing else you can do. Sorry

boo.. that sucks..
Well, thanks anyway

Ehm, I don't want to post a New Thread so I'm gonna ask here:
Does anyone have the pinout for the Tattoo?

Take a look at this. I guess they fix such things (but you never know if they just are after your money. http://www.ort-jtag.com/index.php

Yeah I saw that already. Also, there is a file name Tattoo Jtag on their website in the Support section. However, to access that section you have to enter your products serial number (which is I'm guessing the phone's serial number). I have tried several serial numbers (including mine) and all of them were 'invalid' so I never checked the files out.
Also, they only have one thing in the shop which is a kit and it costs $330 so no thanks

I have a similar problem, I would like to share my knowledge although I must be completely out of way.
My experience is based on the BeagleBoard and Angstrom so I really don't know the HTC HW and Android at all...
- The device boots from an xloader that instructs the device how to proceed with the boot
- the bootloader takes place (great u-boot in the beagleboard ?? in the HTC phone) the bootloader allows for ROM or kernel+rootfs flashing and much more
- now the kernel is loaded.....
User mode applications do not allow to have access to the memory area where xloader and u-boot lie so they should be safe all the time to allow for device reflashing.
So we should have access to the device via bootloader anytime if we knew how... maybe somebody can help us further.
Fabio

Same here...Exact same issue...No Recovery mode...No USB Connectivity, Screen turns on but is blank, alhough I did see Tattoo popping up initially but not any more...All I can see is the LCD back light turns on...Battery does charge...Also when I try to enter Recovery mode screen keeps blinking as if it is trying to restart again and again...Someone help

similar problem here, but i get absolutely no response from the phone, it doesn't even recognize the charger. do i just throw it away and buy a decent one or is there a solution?

Sparky the only way for now to fix that click is to bring it to some service point that have that ort jtag, because only way to fix that is to writte new boot sector on phone . Im sure that i know at least 2 services that have ort jtag in Novi Sad . Look for marvel *Miroslav in Ns, or send me private message

same thing happened to me
just this morning, and in desperation I tried hard to remove the batt cover (prob pressed some of buttons, I felt a jerk and ho it was back in amon ra`s recovery, nect time I just removed the battery waited for 30 secs, then press off&home and hold it till recovery came back) but for good half hour NO REACTIONS , ABSOLUTE BRICK, nothing when I put the usb in PC or in socket, dead screen, no sounds and no reaction to ANY combination of keypress. I guess you could call me lucky (in last few days I flashed at least 3 versions of froyo roms, this afternoon I bought =8GB class4 Kingston, formated it in PC FAT32 default size, copied EVE. from my 2gig rom then just turned it down (yes I am brave) and put the 8gig in tattoo, it works like a charm (finger crossed it will continue)

So is there an available Jtag for the Tattoo yet?

I'm in the same situation. No recovery no fast boot, Damm!
I`ve update psfreedom with psgroove_hermes_v4 zip file then my tattoo reboot and now I only get the Tatto title screen but nothing happends.
Somebody have clue to give back life my phone.
Thanks!

if you can get to the title screen, that means you can connect it to your pc via USB and recover from a backup (I hope you made one)

Hello, I connect my tattoo to my pc, but usb connection is not available yet.
Is There is a way to activate usb when my phone blocks in tattoo logo??
Thanks for reply.

payasi35 said:
Hello, I connect my tattoo to my pc, but usb connection is not available yet.
Is There is a way to activate usb when my phone blocks in tattoo logo??
Thanks for reply.
Click to expand...
Click to collapse
You have to enter in fastboot.
Hold volume down and turn on phone.
Cheers

Sorry but as i said before, I can't access to recovery menu neither fast boot menu.

[q] problems with lg gt540

hi guys.. could you help me with my problem.!
I have an LG GT540 android 1.6 firmware version(stock)
So here are my problems:
1. I tried to upgrade it from 1.6 to 2.1 using this tutorial http://forum.xda-developers.com/show...27&postcount=3 thanks to lavero.burgos for posting it, I was successful at first part, but I cant follow the next because my device wont go to fast boot,, I tried putting it off, then camera+poweron but it doesnt do anything. It doesn't light, no lg logo appears, just nothing although the computer can read the drive when I connect it through usb. So I cannot flash it to 2.3,2.3 because it just wont go to fastboot.
2. When I turn it on normally, It takes long before it response like after 30sec to light, but just light, no lg logo appears although it wasnt bricked because I can use it normally after just waiting to on.(annoying)
3. Since I upgraded it to 2.1, I lost all 3rd party application and the internal apps were the only left, so I copied all my saved apps (.apk) to my sd card but the problem is there is no saved app on my phone to read and install those apps from my sd card.(irritating)
4. My device wont read my sim card, when I start it it says "sim card unprovisioned" so basically I cant connect to mobile networks here in the philippines(im using globe telecom). I feel that Im stucked in the middle of nowhere since I cannot contact and txt all my family and friends.
5. I cant connect to wifi,, when my device detects wi-fi, I try to connect to it but from the log it only try to connect but doesn't obtain the ip address. Even when the wi-fi signal is strong, it does the same thing.
So please help me guys,,I want to hear from my fellow xda-developers badly,,,
PS. also those who have problems with their LG GT540 pls feel free to post and share it with us here... thank you all guys in advance....

hi so let me get it right the phone is working (can turn on and use but cant call) yes? hmmmmm..... try this
MUST DOWNLOAD THIS DRIVERS!!!!
http://dottech.org/android/26188/usb-adb-and-fastboot-drivers-for-windows-for-all-android-phones/
Step one!
1.turn off phone.
2.hold the POWER button till you feel the beep.
3.let go of the POWER button when you feel the beep and hold onto the CAMERA button only.
4.hopefully it turns on to a blackscreen and nothing else(fastboot)
5.unzip this CLICK ME!! to desktop and open the flash all no wipe file
or......
1.turn on your phone.
2.go to settings>applications>development>tick the usb debugging
3.connect phone to computer (make sure phone is on)
4.unzip this CLICK ME!! to desktop and open the flash all no wipe file
5. phone should boot into blackscreen like the one above......
Click to expand...
Click to collapse
Step 2!
both should flash a recovery image. Next
1.make sure the phone is off
2.press POWER button
3.when you feel the beep let go of POWER button and press the HOME button only.
4.phone should boot into recovery mode.
5.take out battery again
6. download a rom into the sdcard using computer
7.go to recovery again using the steps above (steps 1 to 4)
8.select wipe all data factory reset or something like that....
9.install zip from sdcard
10.select from sdcard
11.choose the file you downloaded
12.finish flash and reboot phone.
Click to expand...
Click to collapse

excellent guide! big thanx

bs828 said:
hi so let me get it right the phone is working (can turn on and use but cant call) yes? hmmmmm..... try this
MUST DOWNLOAD THIS DRIVERS!!!!
http://dottech.org/android/26188/usb-adb-and-fastboot-drivers-for-windows-for-all-android-phones/
Click to expand...
Click to collapse
Thanks,, Ive tried the 2nd option on step one and i think my phone successfully got to fastboot(just clean blank screen) so the cmd automatically run and states
C:\Desktop\adb rebootloader
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
error: protocol fault <no status>
C:\Desktop\fastboot flash recovery recovery.img
< waiting for device >
Did I miss something???

ok try again this time with the phone turned on. and then run the script and did you install the drivers?

bs828 said:
ok try again this time with the phone turned on. and then run the script and did you install the drivers?
Click to expand...
Click to collapse
yeah I installed the drivers...

hmmm maybe there are no fastboot drivers(main suspect....) there are a few ways to get it but for mine i just plug my phone in to my pc (windows 7 64bit) it just recognize it and tries to get the "google fastboot interface" drivers from windows update...

Try Volume Up+Search Key+Power to go into Fast boot Mode, There's different keys to activate Fastboot Mode (There is different versions of Fastboot)
Sent from my LG GT540 CM9 PreRC Polish Blood using xda premium

Your phone is/was bricked
Hey, I'm sorry to bing back such an old thread, but I just wanted to say this for posterity: your phone has/had a soft-brick. This means: you can't see Android nor LG boot logos, can't enter Recovery and (maybe) can't access Fastboot, but I'm not too sure on that last one. Besides that, the phone works "okay", but you should try to fix it.
Basically this soft-brick is almost always caught when upgrading from 1.6 to 2.1, so everyone should have it, including me. It took me a whole year to realize how to friggin' fix it lol, but here goes what I did:
Thanks for your help everyone, I came to a solution after a full year lol. Here's my enlightenment, from another Thread:
------------------------------------------------------------------------------------------
Just wanted to leave my 2 cents here, I've been trying to do my best since around august 2014, no success. 2 days ago I retried this, and I DID IT! I will tell everyone what I did very shortly:
My problem that I solved: I can boot, device works like a charm. But: no boot logos, no recovery.
My solution for TL;DR: UNINSTALL ALL DRIVERS FROM DEVICE MANAGER 1ST, then reinstall. After that, flash a fastboot ROM and use it to WIPE ALL THE DATA IN YOUR PHONE! THIS was what I needed and was never explained: you had to WIPE the old data in order to get the boot screens back.
IN THIS ORDER (THANK YOU to those people from previous replies, gathering all your info was of great value):
Uninstall all of your phone drivers from your PC!!! This is what made most of my headaches go away, just use Device Manager and uninstall anything from LGE. After that, plug in your device in your USB ports (always BACK ports, not front ports, important). It should detect all drivers and download them.
IF it fails (it generally does with LGE USB Modem), you can go to Device Manager > Unknown Device (the one that wasn't recognized) > Right Click and Update > Choose 2nd option, then choose "choose from a list of local controllers" (or whatever the button says). After that, scroll down to LG Electronics, Inc. and install what didn't install.
I also found these drivers, but I did not test them: http://www.mediafire.com/download/p693hcz6kkouh19/USB_Driver_LG_GT540.zip
Huzzah!
Now you're set to begin:
FIRST thing you wanna do is a factory reset, this is something I'd forgotten with time, don't make the same mistake as I did. You can do it by turning your phone on and pressing Volume +/- & Home & Quick Search buttons all together for 5 seconds (it works, be patient and wait for it, even if you open the camera or any other stuff).
Download this Google SDK Tools (unzip and put the folder in C:\ drive) and this Fastboot drivers for GT540 (unzip and put the files inside the folder in C:\android-sdk).
Skip this next line if you know your ROM has fastboot.
Now, if you don't have a ROM with fastboot, I recommend you use either European Open+Fastboot or V20C Orange France Fastboot ROM.
Click to expand...
Click to collapse
Since you have Fastboot enabled, now all you need to do is turn off your device (all this with its battery on it, no weird things) and hold the Camera button before turning it back on. This should take you either to a black screen, or simply to no display, like me. Either one will work anyways.
Now press the Windows key > Type cmd and open it with Right Click > Run as Administrator.
In it, type all this, command by command (you can paste by right clicking):
cd C:\android-sdk
fastboot -w
fastboot erase boot
fastboot erase system
fastboot -w
fastboot reboot
Click to expand...
Click to collapse
And now it's go time! Do what everyone else says in here: Take out your phone's battery, SD and SIM cards, fire KDZ Updater up as Administrator (If your KDZ freezes, then it's either faulty or you did not install msxml, look for a good KDZ that comes with that file and delete your current one), choose CS_Emergency PhoneMode and:
1-Plug your phone while holding the volume DOWN button (don't worry! My phone didn't show "Download Mode" either, if you hear the Windows "Somethingpluggedin" Bump noise, it's ok).
2-Flash French V20A
3-Unplug your phone once KDZ says "==FINISHED==".
4-Plug it once again, holding the volume DOWN button.
5-Flash out.kdz (remember! it's CS_Emergency).
Click to expand...
Click to collapse
THANK YOU XDA!
--------------------------------------------------------------------------------------
Also, if you look in here you'll find how to flash an awesome ROM, Cyanogen Mod 10 (should say "Final Version#2).

A501 Tablet Stuck At Boot Screen with "Reboot the device!"

I have an Acer A501 which had Android 3.2.1 on it and recently decided to provide to my parents as a tv guide device so they could sit and research on it. They didn't need the 3G component.
I performed a factory reset and we were unable to use the Market/Play Store to load any of my parents apps. I returned home with the device so decided to try and upgrade to 4.0+
Upon doing lots of reading I started loading an ICS bootloader (a500_a501_bootloaders_apx_ics_v9) with the A500APX Flash.exe I found.
Since doing this my device sits at "Reboot the device!" in big red letters and the Acer logo has turned yellow. When I try a Power+LeftVolume reset it tries to read from SD card but fails. My Micro-SD is 64GB, whats the max size and is there anything special I need to do to try and ressurrect the device?
Can anyone help me with my problem?

When I boot with Power + Volume Up I get shown the following:
Erasing Cache before SD update...
SD update cmd:recovery
--update_package=SDCARD:update.zip

Same issue
dkingsho said:
I have an Acer A501 which had Android 3.2.1 on it and recently decided to provide to my parents as a tv guide device so they could sit and research on it. They didn't need the 3G component.
I performed a factory reset and we were unable to use the Market/Play Store to load any of my parents apps. I returned home with the device so decided to try and upgrade to 4.0+
Upon doing lots of reading I started loading an ICS bootloader (a500_a501_bootloaders_apx_ics_v9) with the A500APX Flash.exe I found.
Since doing this my device sits at "Reboot the device!" in big red letters and the Acer logo has turned yellow. When I try a Power+LeftVolume reset it tries to read from SD card but fails. My Micro-SD is 64GB, whats the max size and is there anything special I need to do to try and ressurrect the device?
Can anyone help me with my problem?
Click to expand...
Click to collapse
Hi
I got a friends A501 tablet and he asked me to upgrade the os. so I flashed the bootloader with the same bootloader as you and got stuck with the same problem. Yellow Acer and reboot the tablet in red. Did you ever find a solution?

Hi! I have exactly the same issue! did any one knows what the steps to fixe it? I tried to follow the unbrick solutions and nothins because I don't even get connection to the computer. The only way to listen the USB connection is with a paper clip press reset and power for 3 seconds (or more) and I will ear the sound of a USB device being connected to the computer, but then I try to write adb usb or adb shell and nothing... and with AfterOTA tool appears in the USB section: ERROR - connect usb cable and enable usb debugging (in dhe Driver section is OK).

Deleted Os in TWRP

Im an Idiot. I went to twrp recovery and wiped everything, since I wanted to install a higher version of the Samsung tab e, and even when twrp told me that there was no OS installed, I rebooted anyways. I was new to this all thing, and had no idea what exactly that meant and thought, 'What could go wrong?' . . . I just wanted a higher device model, man.
Ugh. Now im stuck in the 'Powered by Android' logo screen, and cant boot into recovery or Download mode.
- What's even worse was that I didn't even enable USB Debugging so Adb is out.
- However, it is Rooted, if that even helps.
- Trying to use the Samsung 300k tool to force enter download mode ends up with 'Write file function failed (error 995)'
- My sibling has the same device model as me, but using T Flash via Odin and my 32GB micro SD card doesn't have a reaction to my device. (Or maybe im doing it wrong, since I don't see anything in the sd card when I plug it to the computer)
- Tablet gets recognized via Odin and Computer, but only as 'MTP USB Device', and in Devices, it is in Unspecified as 'Samsung Android'
- Only good thing that came out of this was the info that I had obtained over the past few days that has shocked my siblings as to why I have this much knowledge over Samsung devices and its functions (AKA I feel cool)
But honestly, at this point I am at a loss of what to do, and will not be surprised if I have to get a USB jig to force it to download mode (my only other option left), or take it to a service center to get it fixed. (the other option I have)
But if there is something you guys are aware of, that I had not tried yet, Please guide me.

Anybody?

norakana said:
Anybody?
Click to expand...
Click to collapse
The simplest way to get an operating system again is to put the ZIP file on a working MicroSD card and put it in your tablet, Then boot into the boot loader and choose to install the file by choosing the external micro sd card.
If you're stuck on a boot screen or download, get out of it by holding the power key + volume down, until the tablet resets.
Note for the future:
always backup your device to an external MicroSD card before deleting your existing operating system, or installing a new one.