Database Users

Stuck at limbo (radio update)

Hi all,
I am having a similar problem. I am using 32A Magic loaded with MyHero 2.0.5 and an engineering SPL 1.33.2010. I was trying to try out CursorSense 32A ROM when I hit a snag. The radio update failed. From my console:
sending 'radio' (21376 KB)... OKAY
writing 'radio'...
the screen blanks and the LED lights up in blue, and it stays like that for more than 15 minutes so I ended up having to remove the USB cable and battery.
After this I cannot boot the phone any more. However I am able to go to the HBOOT mode. Whenever I try to load a recovery image using fastboot (recovery-RA-magic-v1.3.2H.img), it will only appear for a for seconds before the phone get rebooted.
I tried using Amon Ra's guide to restore the radio but that does not work. I am able to flash the hboot.img but when I try to flash the radio it gets stuck in a similar situation. The radio update gets sent but does not complete.
Looking at the HBOOT mode I can I have got back my original HBOOT but my radio is still 6.35.07.29.
Any ideas how I can restore my old radio back or at least complete the installation of the CursorSense 32A ROM?
cheers,
Waerren

What about trying goldcard method???

Care to elaborate more? I have a goldcard that I previously used to fix the perfected SPL. I tried this earlier to update my phone. When it comes to the part where it needs to update the radio, the screen blanks and the LED turns blue, and this goes forever. I probably need a different sappimg.
cheers

I made the same mistake when going to CursorSense also. Your flashing the HBOOT before you are flashing the radio then recovery.
Follow these directions:
http://forum.xda-developers.com/showthread.php?t=544761
Once you do that make sure you then follow:
http://forum.xda-developers.com/showthread.php?t=589722
Dont worry it will work. I almost crapped my pants when it happened to me. Once you flash radio, then flash the recovery. When thats done hit "Menu" to power down and THEN boot into recovery mode while the phone is off. You can then apply the HBOOT update and finish the installation of CursorSense.

Hi again,
I have tried the instructions at http://forum.xda-developers.com/showthread.php?t=544761 earlier. I can flash the HBOOT, but when I tried the next step ie flashing the radio, it will give me the blank screen. Were you able to flash the radio using this guide?
cheers
spyz88 said:
I made the same mistake when going to CursorSense also. Your flashing the HBOOT before you are flashing the radio then recovery.
Follow these directions:
http://forum.xda-developers.com/showthread.php?t=544761
Once you do that make sure you then follow:
http://forum.xda-developers.com/showthread.php?t=589722
Dont worry it will work. I almost crapped my pants when it happened to me. Once you flash radio, then flash the recovery. When thats done hit "Menu" to power down and THEN boot into recovery mode while the phone is off. You can then apply the HBOOT update and finish the installation of CursorSense.
Click to expand...
Click to collapse

waerren said:
Hi again,
I have tried the instructions at http://forum.xda-developers.com/showthread.php?t=544761 earlier. I can flash the HBOOT, but when I tried the next step ie flashing the radio, it will give me the blank screen. Were you able to flash the radio using this guide?
cheers
Click to expand...
Click to collapse
When you get into fastboot, remember to use the Hero recovery image, not hte Magic 32A.
http://forum.xda-developers.com/showthread.php?t=561124
That will get you into recovery again. Remember that this recovery uses the Home key to select items.
When you enter fastboot, what information is displayed?
HBOOT, Radio?

Hboot-1.22.2010
radio-6.35.07.29
cursordroid said:
when you enter fastboot, what information is displayed?
Hboot, radio?
Click to expand...
Click to collapse

Sorry typo .. HBOOT-1.33.2010
waerren said:
Hboot-1.22.2010
radio-6.35.07.29
Click to expand...
Click to collapse

Try downloading Amon_Ra Hero recovery.
Code:
fastboot boot recovery.img

Thanks. That worked. I proceeded with the installation and now using the new radio, SPL and ROM.
Looking at the problems I had I am not sure if I could revert back to my old radio/SPL. But then CursorSense ROM is pretty much ok with me!
cheers
cursordroid said:
Try downloading Amon_Ra Hero recovery.
Code:
fastboot boot recovery.img
Click to expand...
Click to collapse

I'm having the same problem...
sending 'radio' (21376 KB)... OKAY
writing 'radio'...
the screen blanks and the LED lights up in blue, and it stays like that for more than 15 minutes so I ended up having to remove the USB cable and battery.
I can get to the recovery screen but I'm not sure where to go from there.
Help please...
HBOOT-1.33.2009
RADIO-6.35.07.29

wishbone416 said:
I'm having the same problem...
sending 'radio' (21376 KB)... OKAY
writing 'radio'...
the screen blanks and the LED lights up in blue, and it stays like that for more than 15 minutes so I ended up having to remove the USB cable and battery.
I can get to the recovery screen but I'm not sure where to go from there.
Help please...
HBOOT-1.33.2009
RADIO-6.35.07.29
Click to expand...
Click to collapse
Now flash the hero recovery through fastboot.
Turn on your phone by holding back and pressing power to get into fastboot.
Then through the hero recovery flash the new SPL.

Thanks that work!

Help needed!
Hi,
I have successfully rooted my HTC Magic to try and update to Cyanogenmod ver. 5.
I also flashed the Amon ra recovery - no issues there. I can boot into fastboot and recovery.
But then the problems started when trying to follow this guide:
(Can´t post link...)
As far as I could see the DangerSPL was needed to be able to run the ver 5. But I believe I accidently flashed the dangerspl before flashing the radio (to be honest - I am not quite sure).
The result is that every time I try to update the radio the flash is stuck during the write (just as OP).
Any hints???
HBOOT: 1.33.2009
RADIO: 6.35.08.29

Trouble Rooting Mytouch 1.2

Hello,
I'm not an expert at modding and hacking but I can definately follow directions. I used a G1 for about a year and flashed it plenty of times with different roms, radios, and spls. I ended up getting a MyTouch 1.2 and proceeded to try to root it so that I can enjoy CM's great roms.
Followed the directions on the unlockr
Made the gold card and went to flash the sappimg.img from the site. The flash went through fine but the phone just got stuck at the HTC Magic screen. Now I know what my mistake was there. I didn't think it was a big deal and continued with the steps. Mainly because I didn't see any infomation on what to do if it doesn't go through. Flashed the radio, then went to the hboot. Received image update failed error message. Long story short, I experienced what having a brick feels like.
The reason I am explaining all of this is for people to learn from my mistakes and to get some clarification on what I am writing next.
I got the phone exchanged (only had it for a day) and began researching more to find out what I did wrong. I found this crypysmoker's thread.
And then I found the message:
READ READ READ. DO NOT download the SAPPimg.zip file it says on that page.
Get the top fixed SPL file 2010 from here
Click to expand...
Click to collapse
In my research, I discovered that the mytouch 1.2 has several spl's that have been hacked and not. I figured out that the file on theunlockr wasn't the fixed spl and that is mainly the reason for my brick and the frozen HTC Magic screen.
I want to enjoy the gifts that CM has to offer. Being stuck on normal 1.6 is well saddening to say the least. But I am worried about flashing the wrong spl and have the situation repeat again as I would figure I would be screwed this time around and wouldn't be able to get it replaced.
Can anyone provide more information about this? Can I flash the Engineerings SPL v1.33.2010 and not run into the same problem? I understand that there isn't a 100% certainty of working. Most of my searches show that more people have bricked this phone than any other.
Thanks in advance and sorry for the length.
Phone Info:
SAPPHIRE PVT 32A SHIP S-ON G
HBOOT-1.33.0013 (SAPP31000)
CPLD-13
RADIO-2.22.23.02

Well, I did it all again. Redownloaded all the files. Setup a new goldcard. This time I let it sit for over 45 mins. Never got past the HTC Magic Screen. Adb doesn't see it nor does the light come on to say that it is charging. Which would show me that it has indeed locked up.
Anyways it shut off on its own since it wasn't getting usb power and I guess the battery died. I'm still able to reboot back to hboot. I attempted to reflash the sappimg.zip file. Right now its going on 10 mins sitting on the
[1] SYSTEM - Unzipping
What I will add tho is that my info changed.
SAPPHIRE UNKNOWN 32A ENG S-OFF H
HBOOT-1.33.2010 (SAPP31000)
CPLD-13
RADIO-3.22.20.17
I tried reformatting the SD and recreated the Gold Card as I noticed some of the Hex changed but still getting the same issue.

the phone won't run anything other than spl 1.33.0013 and radio 2.22.23....w/e x)
Get the sappimg you had before and flash it in hboot mode which should give you spl 1.33.0013. In fastboot mode, flash your spl to 1.33.2010again, then flash radio 2.22.23 or w/e, then flash amon ra recovery, then flash stock spl (1.33.0013).
All the files you need are here: http://theunlockr.com/2010/03/11/how-to-root-the-mytouch-1-2-and-fender-mytouch/
The reason it wont boot up is because you have engineering spl and the wrong radio on. Again, it will only boot up with the stock radio and spl~!!!

hacker01 said:
the phone won't run anything other than spl 1.33.0013 and radio 2.22.23....w/e x)
Get the sappimg you had before and flash it in hboot mode which should give you spl 1.33.0013. In fastboot mode, flash your spl to 1.33.2010again, then flash radio 2.22.23 or w/e, then flash amon ra recovery, then flash stock spl (1.33.0013).
All the files you need are here: http://theunlockr.com/2010/03/11/how-to-root-the-mytouch-1-2-and-fender-mytouch/
The reason it wont boot up is because you have engineering spl and the wrong radio on. Again, it will only boot up with the stock radio and spl~!!!
Click to expand...
Click to collapse
I don't know where I would find the original stock sappimg. The one that is on the website is the sappimg that needs to go on when you are stock at the beginning.
Also my HBoot doesn't seem to be unzipping cause that is where it gets stuck. Is there a way to do it all from fastboot? Since I am currently stuck in the 2010 spl, can I flash the stock spl through fastboot without the radio?
I just don't get why I am having this problem. I followed that website to the letter. And I know that at this point if I attempt to flash the radio back to stock, I will completely brick it.

Since you dont want to flash the radio, flash the amon ra recovery FIRST. Then flash the stock spl. If it doesn't boot up, then you'll need to get the engineering spl back on again and flash stock radio (the one in the link).

hacker01 said:
Since you dont want to flash the radio, flash the amon ra recovery FIRST. Then flash the stock spl. If it doesn't boot up, then you'll need to get the engineering spl back on again and flash stock radio (the one in the link).
Click to expand...
Click to collapse
I couldn't flash the recovery in fastboot.
Tried Fastboot boot recovery recovery.img
Got an error message Recovery not found.
Wasn't sure if I wanted to try flashing the recovery before finding out if it can brick it. Like the original post says, my first MT1.2 I flash the spl from unlockr screen locked up but could get into fastboot so flashed the radio and then tried the spl like the directions say and I completely bricked it.
I don't want to make the same mistake twice.

Unfortunately, there's a chance of bricking every time you flash anything.
Anyways, this might be redundant but is the recovery imaged named recovery.img? Like you actually renamed it? If not, you'll have to type out the exact name.

hacker01 said:
Unfortunately, there's a chance of bricking every time you flash anything.
Anyways, this might be redundant but is the recovery imaged named recovery.img? Like you actually renamed it? If not, you'll have to type out the exact name.
Click to expand...
Click to collapse
No it wasn't named recovery.img, was just using it to save time. I did spell out the recovery's full name.

When you enter the command "fastboot devices" it shows a serial number right? And the recovery image is in your tools folder of your androidsdk folder?
Sorry for the redundant questions, we're just going back to the basics really quick right now.

hacker01 said:
When you enter the command "fastboot devices" it shows a serial number right? And the recovery image is in your tools folder of your androidsdk folder?
Sorry for the redundant questions, we're just going back to the basics really quick right now.
Click to expand...
Click to collapse
yup and yup

I see the problem. Your mobo is recognized as 32a S off H. You're recovery image is probably the G version. What you could do is download the H version and flash it although i doubt your phone will still boot up at that point.
You could try flashing the H version of amon ra's recovery image and afterwards, see if it boots up. Then, if it doesnt boot up, flash stock spl (1.33.0013) and see if it boots up.
I'm pretty sure your phone will end up not booting up and you'll eventually have to flash stock radio as well and then flash the G version recovery back on.
The reason your mobo is recognized as the H version and not the G version is because of the radio.
EDIT: I just realized I made a mistake. I meant to say the mobo is recognized as the H version because of the SPL, not the radio.

EpikFail said:
I couldn't flash the recovery in fastboot.
Tried Fastboot boot recovery recovery.img
Got an error message Recovery not found.
Wasn't sure if I wanted to try flashing the recovery before finding out if it can brick it. Like the original post says, my first MT1.2 I flash the spl from unlockr screen locked up but could get into fastboot so flashed the radio and then tried the spl like the directions say and I completely bricked it.
I don't want to make the same mistake twice.
Click to expand...
Click to collapse
Heres your problem. If recovery is not found then you didnt put it in your Androidsdk\tools folder did you? or did you rename it? Oooorr, you put it in there while adb was running and didnt restart it to see the file itself

crypysmoker said:
Heres your problem. If recovery is not found then you didnt put it in your Androidsdk\tools folder did you? or did you rename it? Oooorr, you put it in there while adb was running and didnt restart it to see the file itself
Click to expand...
Click to collapse
He already said that its in the tools folder.

hacker01 said:
I see the problem. Your mobo is recognized as 32a S off H. You're recovery image is probably the G version. What you could do is download the H version and flash it although i doubt your phone will still boot up at that point.
You could try flashing the H version of amon ra's recovery image and afterwards, see if it boots up. Then, if it doesnt boot up, flash stock spl (1.33.0013) and see if it boots up.
I'm pretty sure your phone will end up not booting up and you'll eventually have to flash stock radio as well and then flash the G version recovery back on.
The reason your mobo is recognized as the H version and not the G version is because of the radio.
Click to expand...
Click to collapse
Sorry for the last reply, I do all my hacking at work so my adb setup is there. So I did this.
fastboot devices
XXXXXXXXX fastboot
fastboot boot recovery recovery-RA-sapphire-c1.6.2G.img
cannot load 'recovery'
fastboot flash recovery recovery-RA-sapphire-c1.6.2G.img
send OKAY
write OKAY
Click to expand...
Click to collapse
Holding home+power, wouldn't boot into recovery. Seems to still be stuck. Went back to fastboot
fastboot flash hboot hboot.nb0
send OKAY
write OKAY
Click to expand...
Click to collapse
Still same thing so back to fastboot I go
fastboot radio radio.img
sending 'radio' <21504 KB>... FAILED <remote: not allowed>
Click to expand...
Click to collapse
My phone now reads
SAPPHIRE PVT 32A SHIP S-ON G
HBOOT-1.33.0013 (SAPP31000)
CPLD-13
RADIO-3.22.20.17
I can tell that the radio is still the old one. It seems the spl worked and put it back to stock but still no recovery and I guess I can't fastboot anything either.
So I assume I need to flash back eng spl and see if it will boot, right?

Even as the recovery and spl are compatible, you see that it still won't boot up. What you gotta do now is flash the engineering spl and do the same as before except flash the radio as well.
In the end, your mytouch should read:
SAPPHIRE PVT 32A SHIP S-ON G
HBOOT-1.33.0013 (SAPP31000)
CPLD-13
RADIO-2.22.23.02
The same as stock before EXCEPT this time, you'll have amon ra's recovery. That's when you know you're done. Just follow the guide from before and you'll be fine.

hacker01 said:
Even as the recovery and spl are compatible, you see that it still won't boot up. What you gotta do now is flash the engineering spl and do the same as before except flash the radio as well.
In the end, your mytouch should read:
SAPPHIRE PVT 32A SHIP S-ON G
HBOOT-1.33.0013 (SAPP31000)
CPLD-13
RADIO-2.22.23.02
The same as stock before EXCEPT this time, you'll have amon ra's recovery. That's when you know you're done. Just follow the guide from before and you'll be fine.
Click to expand...
Click to collapse
So I flashed the eng spl again. Still wouldn't boot. Got the same SAPPHIRE UNKNOWN 32A ENG S-OFF H
did:
fastboot flash recovery recovery-RA-sapphire-v1.6.2G.img
send OKAY
write OKAY
fastboot boot recovery
cannot load 'recovery'
Click to expand...
Click to collapse
I'm still worried about flashing the radio....
but I should fastboot the radio and then the hboot.nb0, right?

Solved
I would like to start out by saying, Thank you so much hacker01 for your help! You don't know how much I appreciate everything.
I was able to get it back working and fully running CM5.0.7
After I reloaded the eng spl, like I said, I was running into the same problems. Wouldn't boot, goes into fastboot, etc.
I grabbed the stock radio and spl NOT from the unlockr page this time but from the link on crypysmoker's thread.
fastboot flash radio radio.img
fastboot flash hboot hboot_7201A_1.33.0013G_091021.nbo
fastboot flash recovery recovery-RA-sapphire-v1.5.2G.img
fastboot reboot-bootloader
Click to expand...
Click to collapse
Just like it said and sure enough got into recovery! Flashed a rom and it booted up.
I know this technically isn't solved cause I really don't know what went wrong in the first place. I can ensure you that I can follow directions and did. The only thing that makes any sense is the files on theunlockr's website is bad. Guess we can just chalk it up to bad luck.
But if anyone wants to root their mytouch 1.2, crypysmoker's thread is definitely the way to go.
Thank you again hacker01! I hope I can pay it forward.

You did it right, it's just that any radio that is not 2.22.23 won't work with the mt3g 1.2/Fender LE right now. And no problem! Glad you got it up and running. Enjoy your mytouch

Mod. edit: not dev related, moved to general

Please, help!
I have the exact same problem: I was following the Unlockr's instructions, made the goldcard, flashed the sappimg without getting any errors, and now the phone is stuck on the htc magic boot screen. I am not experienced and now I am scared sh**less, because the phone belongs to my girlfriend Please, give me step-by-step instructions how to fix it, because I really dont want to improvise. The phone is MyTouch 1.2...
Thank you in advance!!!
SAPPHIRE UNKNOWN 32A ENG S-OFF H
HBOOT-1.33.2010 (SAPP31000)
CPLD-13
RADIO-3.22.20.17

Myouch 3G 1.2 Cant flash anything

So i had to fix the SPL on the mytouch because i kept getting the Fastboot Remote Not allow, So i did the SPL Fix and rebooted and i had a black HTC Magic screen, Got some progress then it said to throw a rom on there but i couldnt get to recovery, i try to flash a recovery and i get remote signature verify fail. So i tried flashing the SAPPIMG again and it is stuck on unzipping, Rebooted again and tried to flashboot boot recovery.img it transfers the recovery and reboots and stuck ad the black htc magic screen again.
Well i made some progress i can flash recovery and stuff now but it wont boot to recovery, i got the recovery to flash successfull but for some reason when i hold home and power it sits at the magic screen
As of right now i have
SApphire PVT 32a eng s-off h
hboot-1.76.2007
cpld-13
radio-6.35.10.18
Well i think ive done everything to this phone............ would be nice to figure somthing out. Been working on it since about 10AM this morning and i got nothing, does anyone have a fix?!
Any help would be appreciated!! Thanks Guys!!

Its bricked. The mytouch 1.2 can only run 1.33.0013 spl and the 2..x radio. Its a hybrid hardware. 32a board with a 32b radio.

NetrixTardis said:
Its bricked. The mytouch 1.2 can only run 1.33.0013 spl and the 2..x radio. Its a hybrid hardware. 32a board with a 32b radio.
Click to expand...
Click to collapse
I can flash a new radio on it and a new SPL on it, it takes that when i flash it

To root the phone you need to use the ENG spl 2010 flash your custom recovery, then stock radio and spl. After that, flash ROMs thru recovery. You can not use any other radio/spl at this time.

NetrixTardis said:
To root the phone you need to use the ENG spl 2010 flash your custom recovery, then stock radio and spl. After that, flash ROMs thru recovery. You can not use any other radio/spl at this time.
Click to expand...
Click to collapse
I think i bricked it now..... it stuck on a 0009 SPL and i cannot do a sappimg it wont unzip and i cannot flash a different spl it does the signature verify fail

Does your phone have the 3.5mm jack? Are you sure you've got a 1.2?

Well, If your phone still turns on and your have a working goldcard, try the ENG 2010 SPL from the Magic SPL thread. once you are back down to 1.33.2010 SPL and 3.22.x radio, fastboot your custom recovery, flash stock mytouch 1.2 radio then spl.
At that point, you won't have any OS tho. so, go into recovery, wipe all (but NOT your SD goldcard). Then flash custom ROM+gapps (if needed)

What is your fastboot info RIGHT NOW....

Remember that if you have a MyTouch 1.2 (with 3.5mm headphone jack) you MUST have the following AFTER you flash your custom recovery.
Radio: 2.22.23.02
SPL: 1.33.0013
So use the engineering SPL (2010) and 'fastboot flash recovery recovery.img' with a Amon_Ra 1.7.0G or Clockwork Recovery for MyTouch devices (NOT MAGIC).
Afterwards reboot to your recovery by holding HOME while booting. If you can boot into recovery then flash your stock spl (1.33.0013) back. Then flash your rom.

supercobaltss said:
So i had to fix the SPL on the mytouch because i kept getting the Fastboot Remote Not allow, So i did the SPL Fix and rebooted and i had a black HTC Magic screen, Got some progress then it said to throw a rom on there but i couldnt get to recovery, i try to flash a recovery and i get remote signature verify fail. So i tried flashing the SAPPIMG again and it is stuck on unzipping, Rebooted again and tried to flashboot boot recovery.img it transfers the recovery and reboots and stuck ad the black htc magic screen again.
Well i made some progress i can flash recovery and stuff now but it wont boot to recovery, i got the recovery to flash successfull but for some reason when i hold home and power it sits at the magic screen
As of right now i have
SApphire PVT 32a eng s-off h
hboot-1.76.2007
cpld-13
radio-6.35.10.18
Well i think ive done everything to this phone............ would be nice to figure somthing out. Been working on it since about 10AM this morning and i got nothing, does anyone have a fix?!
Any help would be appreciated!! Thanks Guys!!
Click to expand...
Click to collapse
I had the same issue the other day while experimenting on my mt3g 1.2. What worked for me was using adb to push the stock mt3g hboot and radio and then rerooting my phone. You can download the files you need from the unlockr.com web page and skim his how-to for android in the unrooting section. Hope this helps.

does it still boot into fastboot, hboot, or recovery?
supercobaltss said:
I think i bricked it now..... it stuck on a 0009 SPL and i cannot do a sappimg it wont unzip and i cannot flash a different spl it does the signature verify fail
Click to expand...
Click to collapse
if it boots into fastboot, hboot, or recovery you are not sunk yet. you will need the "official" sappimg.zip or .nbh on your gold card, but it should go through the steps and re-image it.. this will get your phone back to stock.
are you using a Tmobile MyTouch 1.2? or are you using a Rogers Magic?
the files will be different as the hardware requires differnent drivers.
there are many links on this site, or theunlockr.com that will get you the correct files you will need. make sure you check the md5 sums on anything you download to make sure its not corrupted before trying to flash it.
hope this helps.

[help needed]HTC magic PVT 32A: wrong radio (3.22.XX) and SPL (1.76.0008)

The whole story is a little bit long.
I still can access to fastboot. On the RUU screen, I can read the following information:
SAPPHIRE PVT 32A SHIP S-ON H
HBOOT-1.76.0008(SAPP10000)
CPLD-12
RADIO-3.22.20.17
Nov 3 2009, 15:56:29
Here is how it happened. I flashed the radio to 3.22 and run a wrong RUU file (RUU_Sapphire_HTC_Europe_3.05.401.1_test_signed_NoDriver.exe). The problem comes: after unsuccessfully flash the RUU file (as the radio in the RUU is 6.35), the security is turned ON (S-ON). Those RUU files with radio 3.22.XX have different version of SPL from 1.76.XXX. I cannot find a RUU file with SPL 1.76.008 and radio 3.22.XX. Therefore, I cannot use any RUU file to change the situation (I got a goldcard).
The security is turned on and I cannot change the radio, SPL or recovery in fastboot (cannot pass the infoSignature checking).
Now I still can access to fastboot (such as fastboot devices).
I don't know why I cannot use fastboot to boot a recovery (fastboot boot recovery-RA-sapphire-v1.7.0H.img). I was able to send the recovery img to the device. But the booting of recovery takes for ever.
I can only enter fastboot mode now using any combination of buttons.
Please give your comment and help to solve this.
Thank you very much!

htchd2sg said:
The whole story is a little bit long.
I still can access to fastboot. On the RUU screen, I can read the following information:
SAPPHIRE PVT 32A SHIP S-ON H
HBOOT-1.76.0008(SAPP10000)
CPLD-12
RADIO-3.22.20.17
Nov 3 2009, 15:56:29
Here is how it happened. I flashed the radio to 3.22 and run a wrong RUU file (RUU_Sapphire_HTC_Europe_3.05.401.1_test_signed_NoDriver.exe). The problem comes: after unsuccessfully flash the RUU file (as the radio in the RUU is 6.35), the security is turned ON (S-ON). Those RUU files with radio 3.22.XX have different version of SPL from 1.76.XXX. I cannot find a RUU file with SPL 1.76.008 and radio 3.22.XX. Therefore, I cannot use any RUU file to change the situation (I got a goldcard).
The security is turned on and I cannot change the radio, SPL or recovery in fastboot (cannot pass the infoSignature checking).
Now I still can access to fastboot (such as fastboot devices).
I don't know why I cannot use fastboot to boot a recovery (fastboot boot recovery-RA-sapphire-v1.7.0H.img). I was able to send the recovery img to the device. But the booting of recovery takes for ever.
I can only enter fastboot mode now using any combination of buttons.
Please give your comment and help to solve this.
Thank you very much!
Click to expand...
Click to collapse
Many of this was answered, search the forum.
Here is the thing you have wrong spl radio combination,you have perfected spl. You can do a fastboot boot xxxxxx.img and enter recovery. Then you must flash eng spl 1.33.2010.And you will be unbricked

Thank you for the reply.
I tried fastboot recovery-RA-sapphire-v1.7.0H.img. But after the sending of the image is over, it will stay in booting for ever. I don't understand why I cannot boot the recovery.

htchd2sg said:
Thank you for the reply.
I tried fastboot recovery-RA-sapphire-v1.7.0H.img. But after the sending of the image is over, it will stay in booting for ever. I don't understand why I cannot boot the recovery.
Click to expand...
Click to collapse
You cant boot that recovery try the one hero recovery Ra-magic1.6.2H smthing recovery

I downloaded the 1.6.2 recovery from http://forum.xda-developers.com/showpost.php?p=4549551&postcount=1
But I still cannot boot the recovery(I can send the recovery)

htchd2sg said:
I downloaded the 1.6.2 recovery from http://forum.xda-developers.com/showpost.php?p=4549551&postcount=1
But I still cannot boot the recovery(I can send the recovery)
Click to expand...
Click to collapse
Hmm did you try the sappimg.nbh to restore your magic???

Updated: I tried to use sappimg.nbh in fastboot mode. However, it responses that the main version is older. This is because I have run the RUU (RUU_Sapphire_HTC_Europe_3.05.401.1_test_signed_No Driver.exe), whose main version is 3.05 while the sappimg.nbh is older than this number.
Now I can access fastboot and the hboot, but not the recovery. Of course, I cannot boot the android OS either. Is there a method to root just in the fastboot mode? I have the security turned on (S-ON)?
Anyone got suggestion? Thanks!

Can anyone help on this? really get frustrated

htchd2sg said:
Updated: I tried to use sappimg.nbh in fastboot mode. However, it responses that the main version is older. This is because I have run the RUU (RUU_Sapphire_HTC_Europe_3.05.401.1_test_signed_No Driver.exe), whose main version is 3.05 while the sappimg.nbh is older than this number.
Now I can access fastboot and the hboot, but not the recovery. Of course, I cannot boot the android OS either. Is there a method to root just in the fastboot mode? I have the security turned on (S-ON)?
Anyone got suggestion? Thanks!
Click to expand...
Click to collapse
You need to create a goldcard www.theunlockr.com at How to's and then use sappimg.nbh

I got gold card already. . Thank you!

Do you solve this? I got the exactly problem with you =(

I actually had this same issue months ago and nothing worked. Unfortunately I ended up getting another phone.
Sent from my SGH-T959 using XDA App

r3v4N said:
I actually had this same issue months ago and nothing worked. Unfortunately I ended up getting another phone.
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
What a bad news =( I had sent this phone to repair, but all of their experts cannot fix as well.

That's lame.... did you try the unroot process?
Sent from my SGH-T959 using XDA App

You could try unbricking by flashing the Rogers or Brazilian Android 2.1 RUU. The main version is newer and a goldcard should make it work.
Please make sure your battery is full and that you have a PROPER GOLDCARD!!! Otherwise this will most likely fail.
I've uploaded the sappimg to http://www.multiupload.com/WO0S35S53S
Rename it to sappimg.zip, copy it to the root of your SD card and boot into fastboot (vol-down and power). That SHOULD fix your phone. Then again, it could also brick it even worse, but what do you have left to lose?

After loaded sappimg, it checking sappimg, then went back to HBOOT. Nothing happened. I've tried to recreate my gold card, no luck with it =(

[Q] magic. only fastboot. boot recovery not working. sappimg not working

Hi.
i need some advice to see what can i do to get the phone working again.
case:
htc magic 32A.
ENG S-OFF H.
hboot-1.33.2005
radio.3.22.20.17.
i had cyangoenmod 6. working just fine! for several months. a couple a days ago (without installing anything new) it crashed, and now it gets stuck in the splash screen.
symptoms:
i can enter fastboot. fastboot devices lists the phone.
i can't enter recovery. fastboot boot recovery.img doesnt work, still stuck in splash screen. fastboot flash recovery.img doesnt work either.
i thought the next step would be a factory reset so i got a friend to copy the sappimg.zip on my sdcard and tried to run hboot mode, but it says NO IMAGE! when checking SAPPIMG.zip
should i use RUU? whats the procedure there?. from where i run it?. also i don't know whats the right one for my phone. i see this list: http://forum.xda-developers.com/showthread.php?t=659403.
and fastboot getvar version-main gives me: 3.05.529.9. while CID gives BSTAR301
i dont see that exact version in the list, and the only one with that cid is 2.20.515.5 HTC Chile BrightStar/Entel. im a little confused here...
thanks for any help!.

the problem seems to be bigger. I decided to go with the RUU directly from Htc site. For my device, i gave my serial no. and downloaded the .exe for magic_brightstar. It did successfully updated everything (?), radio, hboot, recovery, system, splash....
But i start the phone and it is still stuck in the freaking init screen.
I don't understand, what else can i do?.

Can you enter the recovery now?

No. the recovery doesn't enter. still frozen.
I'm trying to have a working goldcard, but it has been a little tricky without another phone to convert the sd. I'm following what amon_ra suggested here http://forum.xda-developers.com/showthread.php?t=548218. Because right now my hboot is locked (after running the factory RUU) and i can't run any of the flashing fastboot commands.
will post what happens...

ok the goldcard did its job, i have again eng spl with all fastboot flashing enabled. but i cant get into recovery yet, no matter what.
at this point i'm thinking on flashing the original hboot, radio and go claim the guaranty...
Any ideas before throwing the towel???

i was thinking that if it is a hardware/firmware problem, it should be possible to test via fastboot oem commands, isn't?

Download my fastboot commander from my signature (the magic version).
It has a special 32A tab.
Using the tool, flash the old combo and see if you can enter recovery afterwards.
You can also flash the new combo and give it try...