Hi to you all! Please provide me a schematic of this type of cable. I ordered one from a site and it won't work. I'd like to try to upgrade to WM6.1 and I don't have a working cable. Please give me at least a pinout for this PDA. The one that's on pinouts.ru - I don't think it's good for this model.
Thanks a lot!
No answer yet? I got another USB cable from provider, which is also not good, even though it has "usb detect" and USB data + and USB data - pins present.. It just says " unrecognized usb device" please! I want to upgrade to Windows mobile 6.1, that's all I wanna do. thanks a lot to anybody who will answer.
Why do you think that there is something wrong with the cable?
It's quite possible that connector on iPAQ is bad.
Spiaatie said:
Why do you think that there is something wrong with the cable?
It's quite possible that connector on iPAQ is bad.
Click to expand...
Click to collapse
Hi!
It turned out I was doing something wrong. The phone needed to be in bootloader mode so that the drivers provided into this forum to work properly. Thus, I can confirm that the schematics for IPAQ from pinouts.ru works just fine at least for the USB connection part. As for drivers, they are posted here in this forum.
I also attached an image with the response of that cmd command.
Thanx to You all!
Keyboard
Hi again! Anybody has a fix for keyboard issue? Key problem like: Delete function instead Enter and such... Please help!
Thanx!
Related
Hello everybody,
first of all, I want to apologize myself for my questions, because they are often discussed in several forums (USB-RS232).
BUT I did not find a solution. Sometimes I found "it works" and sometimes for the same problem "no chance". Enough ;-)
I'm writing a program in VB.net to log
1) all data from the GPS at COM4 and
2) all data from an acceleration sensor which might be connected via the USB-Port of my XDA Orbit (HTC Artemis).
Logging the GPS-data is no problem excepted the speed of the Sirf star III Chip. Can it update faster than 1sec?
My main problem is the connection to the sensor. I know that port of the XDA is an USB-Client. The data I receive from the development-board is sent via RS232-out.
My question:
Is it possible to get those data-strings into the xda to log them via the existing USB-port? How can I implement it?
Can I connect the USB-plug and the RS232 like I found several times in this forum? Does it work???
The solution of this project is very important for me.
For everybodys help, I am very grateful.
Thank you very much.
Greetings from Germany
Dee
If I understand you correctly, you wish to connect an RS232 output to the mini USB connector on your device and log the serial data coming into the USB port? Yes, this is possible, but not without a PIC microcontroller in between. RS232 runs on, IIRC, +9v/-9v, while USB runs on +5v. If you directly plug an RS232 output into your USB input without anything in between you very well might fry your phone. I don't recommend it.
Fortunately, RS232 to USB devices are easily found, both schematics and pre-made adapters.
A quick Google search found this schematic:
http://pinouts.ru/SerialPortsCables/usb_serial_adapter_pinout.shtml
fluxist
Hi fluxist,
thank you for your answer. It sounds very good to me. But does it work with an USB-Client-PDA?
Thanx a lot.
Greetings
Dee
USB Client to rs232
Hellow
If You want "USB Client to rs232" interface please contact me([email protected]). I can produce it for You. I Use this converter in many PDA projects.
Best regards
RBA
Hi guys, I really need your help, I have a QTEK 9100 and I cant use usb connections like sync etc so I use blueetooth to sync, but I dont know if its possible to flash it through bluetooth . Can anyone help ?
MY usb is not working on the QTEK it needs to be fixed on a store I guess.
When I power on with camer button I dont have the USB information on it.
Put simply, no, you cannot.
Read the linky in my siggy and it will explain all to you. It is a long and very detailed thread about the woes of a damaged usb port and what can and can't be done.
Hi , guys, now ,my X7500 can not link to My PC , the note is "unknow device, pls try again", i send the phone to the cellshop, the egngineer said ,the synchronization IC has been broken!
who can give a help ?
where are i can find some interanl pictures of X7500?
http://www.pdacenter.ru/razborka/razbor_htc_athena/
rorydaredkign said:
http://www.pdacenter.ru/razborka/razbor_htc_athena/
Click to expand...
Click to collapse
thanks, but i can not open the site, could you pls give me other adress?
dear, who can help me ?it is very urgent !!!!!
Who can help ?
My car's white - how fast does it go?
And now for some more detail:-
Is the error coming up from Windows, or ActiveSync?
What OS and ActiveSync version are you using?
Have you ever been able to sync?
What ROM is your device using?
Are you using USB or Bluetooth Sync?
If its ActiveSync, you could try deleting any existing profiles within the Application and trying again.
Have you tried both a soft and hard reset of the phone?
Have you tried uninstalling and reinstalling ActiveSync?
Have you got the latest version of ActiveSync?
Have you tried synchronising over bluetooth instead of USB (or vice-versa)?
Have you tried google to resolve your problem?
Digital.Diablo said:
My car's white - how fast does it go?
Click to expand...
Click to collapse
That made me laugh right out loud!
it is ok before 15th,Feb.the software and device is ok.
but some time ,the USB port is not stable , you need to put a book above the USB cable.
one day , the device can not link to PC whatever i shake the cable.i change
a new USB part of the device , but it can not working yet.
the repairer said, the control IC has broken , is it right ?
nmurphy said:
That made me laugh right out loud!
Click to expand...
Click to collapse
Tis an old quote passed down to me as a junior IT tech from the wizards of the mainframe, and illustrates the point perfectly I think.
Veron_fat - when you say you have "change a new USB part of the device", is that the USB cable, or the Mini-USB port on the device?? I had a fault with my first charger where the connection eventually went wrong within the connector on the cable - swapped it out with a new charger and all was well again. I have however also broken an Axim x50v sync port with too much flexing - the connector broke the solder ports on the mobo.
I'd be surprised if you'd broken the IC - can someone else advise if my memory is correct and the USB device controller is integrated into the main CPU. Is this also shared with the USB host controller? I'm thinking that if Veron_fat has the 4 in 1 USB cable, he can test that to see if it is the IC, or the port that is at fault.
I do think though Veron that you've buggered the port, and it will either be a resolder on the port by a skilled electronics engineer, or a new mobo.
Digital.Diablo said:
Tis an old quote passed down to me as a junior IT tech from the wizards of the mainframe, and illustrates the point perfectly I think.
Veron_fat - when you say you have "change a new USB part of the device", is that the USB cable, or the Mini-USB port on the device?? .........
Click to expand...
Click to collapse
1. it is the Mini usb port in device
2. i change more than 4 piece usb cable
3. you mean this divice have not the sperate IC for synchronization?
4. all information from the phone repairer ,i donot belive his voice , but i just want to get some picture of internal view of u1000 to check if there have some IC or something......
veron_fat said:
1. it is the Mini usb port in device
2. i change more than 4 piece usb cable
3. you mean this divice have not the sperate IC for synchronization?
4. all information from the phone repairer ,i donot belive his voice , but i just want to get some picture of internal view of u1000 to check if there have some IC or something......
Click to expand...
Click to collapse
Why not just send it back to HTC for repairs/diagnostics? It might only cost you shipping. Just my 2 cents.
tootallk2000 said:
Why not just send it back to HTC for repairs/diagnostics? It might only cost you shipping. Just my 2 cents.
Click to expand...
Click to collapse
yes, but i have not the guarantee, i am not sure if they can repair this device.
who can give me a adress for the X7500 internal picture!!!
i want to see the stomach!!
I have a PDF of a repair Manuel if you would like it. I uploaded to this link. I hope it helps...TJ
"http://www.mediafire.com/?baidzmnlgow"
TrekkerJmm said:
I have a PDF of a repair Manuel if you would like it. I uploaded to this link. I hope it helps...TJ
"http://www.mediafire.com/?baidzmnlgow"
Click to expand...
Click to collapse
thanks, try it!
Hey guys,
I want to know what is possible with our USB-Connector.
What does it support/not support? (Host-Controller, driver...)
How is it build up? (beside the specs in the Wiki)
I'm happy with all helpful answers!
greetz
playdo
usb
It's a mini ext USB and dispite the bumff from HTC will work with any ext mini USB device.
My friends got a USB charger for his car , this works fab in our phones.. have a look in teh interweb , as long as it's gto our connecter it will work .. ( however there are some issues with poliarity as some of the pins are set up diffrently ..
I searched the internet about this topic (because forum search seems to be a bit crappy )
So I found a thread about USB-Host in Touch HD.
Now my question:
Is there a possibility to use the Touch HD as USB-Host device or is our Touch HD just a pure Client?
I thought about a mouse or external Harddisk. But if there is no Host-Controller, it's impossible
PS: I just found some thread about this topic (search funtion is weird finds "usb host" but nothing with "usb")
So from what I see, there is no host capability with our Touch HD?
Nobody tried Zeno driver?
There is an old 3D about HD USBHost: you could search.
HD has Host capability by chip but extUSB lacks of output power: serch 3D to confirm that
D'rath
Many thanks D'rath, that mainly what i want to hear
I think it's possible to bypass the lack of power by an Y-Cable or something like that. If not, i'm going to solder it together
Lets hope it works
I tried it
But I got bad news so far
Just soldered a USB cable together, so power supply is provided and I installed Zeno USB Host Drivers to get mouse support.
But it didn't worked
Just got the popup with "New USB Mouse" but nothing more.
Maybe there is some hope, that it will work, but I didn't get it to work.
greetz
playdo
playdo said:
I tried it
But I got bad news so far
Just soldered a USB cable together, so power supply is provided and I installed Zeno USB Host Drivers to get mouse support.
But it didn't worked
Just got the popup with "New USB Mouse" but nothing more.
Maybe there is some hope, that it will work, but I didn't get it to work.
greetz
playdo
Click to expand...
Click to collapse
Did you try using a flashdrive and see if it gets recognized ? I'll be interested in that.
I have just flashed a new ROM and I'm experimenting a bit.
But i try to test it in the next days, if I find the time
By the way, my car is rusting and i got little time because I gotta repair all the **** >.<
It s a little strange but seems like no one in this forum tried to connect usb devices to our phone since zeno usb host driver has been released.I tried to search in google but no one tried in acer s200...Are there anyone that know if it work before i try it by myself?
I've tried it
HI, i have tried it with a 1gb, 2gb, 4gb, usb flash storage. But it seems not to work. It don't shows me another device in the explorer (win explorer or resco explorer)
Maybe someone have tried it succesfully?
external power is required, see usb-host scheme by dcordes... keep in mind, however, that hd2's got a micro-usb connector
tsamolotoff said:
external power is required, see usb-host scheme by dcordes... keep in mind, however, that hd2's got a micro-usb connector
Click to expand...
Click to collapse
Hi tsamolotoff,
the usb host work properly:
Yes i built a usb cable with external power supply.I ve made a cable that supply 5v to the device i want to attach to the s200,but only the two data lines go to the phone.But this afternoon i ve read a german forum and someone said that in some cases (nokia) the usb host cable must supply 5v even to the pocket pc,and i want to try by this way.Stefano wich cable have you made to get the s200 found the usb mouse and the pen drive in linux kernel?Do you think that with zeno drivers we can use the usb host even in windows?
Stefano_1986_
Interesting, however, it'd more exciting if it worked under wince (did you check?)
Axel85 said:
Stefano wich cable have you made to get the s200 found the usb mouse and the pen drive in linux kernel?
Click to expand...
Click to collapse
This is my cable:
Axel85 said:
Do you think that with zeno drivers we can use the usb host even in windows?
Click to expand...
Click to collapse
tsamolotoff said:
Stefano_1986_
Interesting, however, it'd more exciting if it worked under wince (did you check?)
Click to expand...
Click to collapse
I have checked but not working
ok almost like mine.This morning with this cable and zeno drivers i ve noticed that if you connect a device like a pen drive,the screen turn on backlight,and it s not for the fact that i attached the cable with 5v,the tension is always present in the usb cable.So maybe the hardware feel the new device but have not the correct drivers to control
What is the solution I have the same problem
so all, what's the solution then? if I want to conect my F1 to a CF card reader? how to use external power...
It doesn t work under windows mobile...This is the solution.
It only work via linux kernel (tested a mouse a keyboard and a usb drive),but since no android build is avaible for s200 you can t use it.
So usb host is supported by s200 hardware,but it s locked in windows mobile kernel and can t be changed.this is a really great stupid thing i know...but sadly it s the true
Guru correct me if i writed something wrong
maybe it can work now, coz Android can be loaded in S200...
I just think if my S200 can read the photos from CF card reader...
yes sure we can make it work under linud distros or android as proved by stefano some month ago