Hello,
I have been using the ChuckyROM for quite some time now, and I have been very pleased. Today, when I got the phone out of my pocket, I noticed that it was completely shut down (even if it had its battery somewhere around 98% last time I checked). I started it only to see a white screen, nothing at all happening. I removed the back cover, reset the phone via the red small button, but the result was the same white screen. I decided to remove the battery, the SIM card and the SD card and leave it to cool off for 10-15 minutes. 15 minutes later, I picked it up, put everything back together, started it, and only got that annoying white screen.
I left it charging for about 3 hrs (it usually charged up in about 2 hours, tops) and the LED kept staying red, as if it was not fully charged. I disconnected it, and the LED still wouldn't go off. I tried booting it, nothing happened, at all. Soft reset via red button, and the LED went off and the phone went back to that white screen again.
Right now it is connected to my laptop, apparently charging (red LED on), and I really don't know what to do.
My ROM was ChuckyROM with the GTX Sense theme.
I'm using HSPL 1.42.HSPL.
Radio version was 2.08.50.08_2.
I also have to mention that I can get the bootloader showing up, so I might try and revert to a stock ROM, but I preferred to post here first and get some suggestions.
What can I do? Please help me!
Thanks in advance!
If I were you, I might just take my chances and install a Stock ROM. See what happens after that...
Yeah, this was my intention to be honest. Do I need to change the HSPL before doing this? And if not, can I change it back to 1.48.0000 after reverting to a stock ROM?
You don't need to revert back to a stock ROM. Just flash another custom ROM!
From what I understand, if you flash a stock ROM via USB, you will still keep HSPL. If you flash a stock ROM via Storage Card, it will take away your HSPL, and you will need to redo HSPL.
If you do go back to a stock ROM, flash using USB so you don't have to redo HSPL.
sumflipnol said:
You don't need to revert back to a stock ROM. Just flash another custom ROM!
From what I understand, if you flash a stock ROM via USB, you will still keep HSPL. If you flash a stock ROM via Storage Card, it will take away your HSPL, and you will need to redo HSPL.
If you do go back to a stock ROM, flash using USB so you don't have to redo HSPL.
Click to expand...
Click to collapse
I see, but I want to revert to a original SPL, because I will most likely take it back to service for other faults as well.
If I download a stock ROM and upload it to the SD card, everything will become stock, right?
Sorry for double-posting, but I just tried installing _HTC HD2_RUU_Leo_HTC_WWE_EastEurope_1.48.479.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship, downloaded from HTC's site via USB connection while in bootloader, and it said that "the image is corrupt" and the process failed.
What now?
anrabi4 said:
I see, but I want to revert to a original SPL, because I will most likely take it back to service for other faults as well.
If I download a stock ROM and upload it to the SD card, everything will become stock, right?
Click to expand...
Click to collapse
Ah, I see what you're saying.
Yes, flashing a stock ROM from the SD-card will make it all stock.
anrabi4 said:
Sorry for double-posting, but I just tried installing _HTC HD2_RUU_Leo_HTC_WWE_EastEurope_1.48.479.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship, downloaded from HTC's site via USB connection while in bootloader, and it said that "the image is corrupt" and the process failed.
What now?
Click to expand...
Click to collapse
Try re-downloading the ROM. Or you can find another stock ROM from HTC or HTCPedia.
I`m trying to download RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship.exe.
I have formatted my SD card to FAT32, but what should I try first? Going to bootloader and try to install the ROM mentioned above?
anrabi4 said:
I`m trying to download RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship.exe.
I have formatted my SD card to FAT32, but what should I try first? Going to bootloader and try to install the ROM mentioned above?
Click to expand...
Click to collapse
I feel even worse now! I have tried both ways, first using the new ROM via USB in bootloader, it said the same thing, that the image is corrupt. I then extracted ruu_signed.nbh, renamed it to LEOIMG.nbh, copied it to my FAT32 freshly-formatted SD Card, put it in the phone, and it said "Update terminate UPDATE FAIL", sticking at Radio_V2...
What can I do now? Should I try and flash another radio, or...
if that wwepmr is not your phones original stock rom, then it will fail, because it will reset your spl and then try to flash the rom, but of course it will check the region and vendor id and get a missmatch.
i would do it like this.....(no need for sd card flashing at all, that's old news)
run hspl2, make sure you have hspl installed, run the wwe file in your last post over usb, when its flashed, rerun hspl2 and choose 1.42.0000 and you're ready to send it back.
thanks for your reply, samsamuel!
unfortunately, running hspl2 seems to do nothing. I have 1.42.HSPL already installed, and I tried choosing 1.42.0000, it says it's succesfull, but my bootloader still displays 1.42.HSPL.
When trying to run the WWE, it gets stuck at 0% for 10-15 minutes, then says that the connectivity is poor.
anrabi4 said:
When trying to run the WWE, it gets stuck at 0% for 10-15 minutes, then says that the connectivity is poor.
Click to expand...
Click to collapse
that sounds like a usb timeout problem.
Boot to bootloader manually, and when 'serial' turns to 'usb' on screen, then run hspl2. Keep trying this with all your different USB ports. (USB ports around back of the PC generally work better than ports in the front.)
Just tried both the WWE and task29 through all of my laptop's ports, and I get the same result: it won't go over 0% whatever I do.
I don't understand... each of the USB ports on my laptop recognized my HD2 and successfully installed the driver in less than 10 seconds after connecting it... What could be wrong?
Honestly, I was thinking of putting it in the microwave oven for 3 or 4 seconds, just enough so the CPU gets fried, then get it to a service center and complain about how it stopped working all of a sudden...
you did try simply removing the sim & sd card and battery, reinstalling the battery, holding both volume up & down simultaneously and depressing and holding the phone disconnect button to do a hard reset, right? I just didn't see that in previous posts and figured that should be near the beginning.
Related
Got my nephew's HD2, it's stuck at the stick together screen. I believe he had the second to last stock ROM, not the most recent. I can get into the boot loader and SPL is 2.10. I was able to flash the latest stock rom 3.14 from via usb but no luck. I get Update complete, Update success when I flash via sd card, but still no luck. When I attempt to Task it, it gets about 19% and says "image file is corrupted, Please check you update utility" and "Error [270] : update error" and the phone reboots. I'm gonna try to flash hspl3 and an energy rom and see if it'll come back..what else should I be doing? I heard I had to wait 10 min after I get success when I flash via sd before I manually reboot, is this true? thanks...
mr1ncred1ble said:
Got my nephew's HD2, it's stuck at the stick together screen. I believe he had the second to last stock ROM, not the most recent. I can get into the boot loader and SPL is 2.10. I was able to flash the latest stock rom 3.14 from via usb but no luck. I get Update complete, Update success when I flash via sd card, but still no luck. When I attempt to Task it, it gets about 19% and says "image file is corrupted, Please check you update utility" and "Error [270] : update error" and the phone reboots. I'm gonna try to flash hspl3 and an energy rom and see if it'll come back..what else should I be doing? I heard I had to wait 10 min after I get success when I flash via sd before I manually reboot, is this true? thanks...
Click to expand...
Click to collapse
In order to flash from SD you need HSPL, I would slap hspl3 on there and then flash the stock ROM of your choice.. and if you dont want HSPL to stay, you can flash the stock Rom from SD and it will overwrite HSPL with the SPL for that Rom.
Ok, so I flashed HSPL 3, then flashed the latest energy Rom but had no luck with that, just hung at the boot screen. So I then flashed the stock ROM again from the SD card and no luck again. I'm starting to think there is a hardware problem. He told me before the battery got "really hot" before it crashed. Also, with the original "dead" battery in, when i plug it in to a charger, I get no charge light, but the phone comes on immediately without me pressing anything and hangs at the stick together screen. Battery pins are ok, compared to mine, not interested in trying his battery in my phone.
im having the same issue, im beginning to think its an internal memory issue because it will inconsistently flash sometimes hanging on 74% or 12% error out, then with nothing changed it will take the entire flash and just not boot with an energy rom it will however vibrate 7 times when stuck on the flash screen of the energy rom
Ok guys try doin this real quick..
First post what your bootloader shows.
Then remove SD and Sim.
Then, enter bootloader again, sync to PC and perform task29 followed by a hard reset.
Now try flashing stock 2.13 ROM (from bootloader)
-If that doesn't work try removing hspl and then flash stock.
no dice flashing task29, i flashed then hard reset then tried to flash energy, it still hangs on random install %'s...redid the task29 and tried stock no dice, removed hspl and tried stock but wont even get past 0%
this phone was screwed from jump street though, stock original rom froze right out of the box...im thinking corrupt internal memory
well right now my bootloader says:
PB81120 MFG SS-B3
SPL-2.00.1000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
but that's because I just tried this:
http://forum.xda-developers.com/showthread.php?t=668347
so gonna bring it back to current factory ROM in just a min and then see. I can flash whatever ROM, SPL, or HSPL I want just wont get past boot screen regardless. I can even task 29 with HSPL3. Not sure what else? maybe the order of steps I'm taking.
Edit: well I could flash back and forth tried using HSPL3 with 2.00 support and get critical error so prolly dead for sure now...glad it aint mine RIP HD2, still happily take any suggestions on getting it running again tho...and thanks again for the help...maybe a goldcard? but i'm not quite sure how that works...
Okay, finally made it back to latest factory ROM 3.14 from SD card, so now I'm back to SPL-2.10.0000
but still no boot....not sure what to do...
im having similiar issues with it not booting, i think i have a hardware issue as well.. but this seems to do the trick for me when tryin to boot..
if flashing is successful but you are stuck at the "stick together" screen (with or without the 3 version numbers in the bottom left corner), do these steps:
1. take out the battery
2. wait AT LEAST 5 minutes before putting the battery back in (some have reported waiting 10 minutes minimum)
3. put the battery back in and turn the phone on
4. phone should boot up into windows within 2 minutes.
5. If it doesn't boot (within 5 minutes), repeat steps 1 through 4. (sometimes for me it takes 2 rounds of this for it to boot)
i'm not sure how the internal memory works, but I would sure like to know.
it seems the battery needs to be removed for a few minutes to "erase/empty" out the internal memory data (possibly corrupt data). It is possible my hardware causes some internal memory corruption, because when the phone boots, it works perfectly until some 'random' system crash occurs.
Oh, So I tried to load up a stock T-mobile ROM and it wouldnt load. I used VBNROM reloaded 2 (the ROM stripped down for Android use), loaded up first try.. which makes me wonder if its a particular sector on the internal flash memory that is corrupt?
The order I used entering into bootloader before each step (with phone off, hold down vol down button while plugging in USB cable thats connected to PC)
1. HSPL3
2. task29 (make sure microsd card and SIM card are NOT inserted)
phone is off. unplug sync cable.
3. insert microSD card that has the VBN rom correctly renamed leoimg.nbh for memory card flashing.
4. hold vol down button and power on. keep holding the vol down button until you pass the tri color screen into a gray color screen that says "loading..." then release the vol down button, follow the instructions to flash from memory card.
5. once successfully updated, take the battery out for 5 minutes, take out the SD card.
6. replace the battery, and turn the phone on.
7. phone should go to "stick together" screen, then show the red numbers in bottom left corner, then show a black screen with animation "clarity" text. Once you see that you know it will work
try that and tell me if that works for you to boot. if it does, then there must be a internal memory issue. (this rom is only 75 megs!)
EXTRA NOTES:
- it's possibly SIM card related too.. Phone had sim card and sd card with vbnrom successfully installed. i had loaded up android successfully, then shut down the phone. I tried to boot the phone again, but the phone went pass the 'stick together screen' then to a black screen and restart it self, then stayed at the stick together screen. This was remedied by taking the SIm card out, and trying again.
- with SIM card not inserted and phone successfully in windows mobile, put phone into flight mode, turn off phone, insert SIM, turn phone on. THis booted the phone for me.
mr1ncred1ble said:
Okay, finally made it back to latest factory ROM 3.14 from SD card, so now I'm back to SPL-2.10.0000
but still no boot....not sure what to do...
Click to expand...
Click to collapse
Just for kicks, try to remove the SIM and SD Cards to see if they change anything.
Also, if the above post works, you can install Android on your SD Card and you will still have a working phone? Better than a paper weight...
nothing regardless sim or sd is in or out just Stick Together and no red numbers...Gonna leave the battery out for a while and see but not holding out much hope..just don't get why i can get to the bootloader no prob and flash whatever, task it but the os won't boot...
Okay, with no sd or sim inside the phone, I flashed HSPL3, Task 29, then Radio 2.10.50.26 (same one that's on my hd2), then VBNROM, Hard reset and.. everything went surprisingly smooth but still not booting.. gonna leave the battery out for a while but it was dead when I got it sooo...we'll see..I did that all via USB, would it make a difference if I used SD card for each step? idk..
thanks again guys
mr1ncred1ble said:
Okay, with no sd or sim inside the phone, I flashed HSPL3, Task 29, then Radio 2.10.50.26 (same one that's on my hd2), then VBNROM, Hard reset and.. everything went surprisingly smooth but still not booting.. gonna leave the battery out for a while but it was dead when I got it sooo...we'll see..I did that all via USB, would it make a difference if I used SD card for each step? idk..
thanks again guys
Click to expand...
Click to collapse
when phone is off, can you charge the battery? (orange charging LED)
it's good idea to have full battery while flashing and all this booting nonsense
when it's stuck on Stick Together and i plug the charger in, i do not get the orange led but, i do believe the battery is charging. when i got it, it would not even come on with that battery. after leaving it pugged in like that for a while it came on reliably. could a low batt. cause this type of problem?when i started working with this phone i was using my fully charged batt. and having same results. been using his batt. since it charged. could his battery be good or bad? the only way to tell for sure is to put his batt. in my phone and see if its charging. should i be concerned about his batt. damaging my phone? the owner seems to think the battery caused his problems cause it got "very hot" before it stopped working.is no led a sign of a hardware problem?
mr1ncred1ble said:
when it's stuck on Stick Together and i plug the charger in, i do not get the orange led but, i do believe the battery is charging. when i got it, it would not even come on with that battery. after leaving it pugged in like that for a while it came on reliably. could a low batt. cause this type of problem?when i started working with this phone i was using my fully charged batt. and having same results. been using his batt. since it charged. could his battery be good or bad? the only way to tell for sure is to put his batt. in my phone and see if its charging. should i be concerned about his batt. damaging my phone? the owner seems to think the battery caused his problems cause it got "very hot" before it stopped working.is no led a sign of a hardware problem?
Click to expand...
Click to collapse
from my experiences, i know the phone is charging when: 1. phone is off with battery inserted, 2. plug in charger, 3. wait for orange charging LED light to come on.
when you plug in the charger while it's stuck on the "stick together" screen, no light will come on, and I don't think it's charging when this occurs.
It's charging alright. Took the battery out of the dead hd2 and put it in mine. It was pretty low 3% or something. Took it out put it back in the dead hd2, plugged it into wall charger. Phone came on by itself and froze at stick together screen and NO orange LED. I left it like that and watched a movie. Then took the battery out of the dead hd2 and put it back in mine. Now says 66%...gotta say it's charging.
mr1ncred1ble said:
It's charging alright. Took the battery out of the dead hd2 and put it in mine. It was pretty low 3% or something. Took it out put it back in the dead hd2, plugged it into wall charger. Phone came on by itself and froze at stick together screen and NO orange LED. I left it like that and watched a movie. Then took the battery out of the dead hd2 and put it back in mine. Now says 66%...gotta say it's charging.
Click to expand...
Click to collapse
oo nice, good confirmation for charing. i figure no orange LED its crashed
mr1ncred1ble said:
well right now my bootloader says:
PB81120 MFG SS-B3
SPL-2.00.1000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
but that's because I just tried this:
http://forum.xda-developers.com/showthread.php?t=668347
so gonna bring it back to current factory ROM in just a min and then see. I can flash whatever ROM, SPL, or HSPL I want just wont get past boot screen regardless. I can even task 29 with HSPL3. Not sure what else? maybe the order of steps I'm taking.
Edit: well I could flash back and forth tried using HSPL3 with 2.00 support and get critical error so prolly dead for sure now...glad it aint mine RIP HD2, still happily take any suggestions on getting it running again tho...and thanks again for the help...maybe a goldcard? but i'm not quite sure how that works...
Click to expand...
Click to collapse
I'm sorry bud, but you have yourself and MFG SPL. I started a thread a while ago HERE, and I believe they've found a solution (post 2)
candyman123 said:
oo nice, good confirmation for charing. i figure no orange LED its crashed
Click to expand...
Click to collapse
you may be right tho. Although it's charging, no LED may mean hardware failure of some sort.
Scabes24 said:
I'm sorry bud, but you have yourself and MFG SPL. I started a thread a while ago HERE, and I believe they've found a solution (post 2)
Click to expand...
Click to collapse
i was able to get my SPL back to 2.10 here's how i did it:
http://forum.xda-developers.com/showpost.php?p=9451339&postcount=157
but still stuck, won't boot
I wonder if a manual MTTY Task29 would be any different? Would it be more thorough?
Along the lines of a SMALL ROM maybe flashing due to higher memory space corrupted, you might try my SUPER Ultra Lite ROM and see if that boots. (45MB Small)
http://www.mediafire.com/?aebnj8erjj4wpva
Hey, so I have an HD2 that was flashed badly. No problem, enter bootloader, reflash, right?
Strangely enough, it was acting strangely, and would freeze while in bootloader mode (plug in, nothing would recognize it, plug out and USB is still on the screen).
I pull the battery, try again, and get to flashing the Radio, it stops at 96%, and then fails. Try to do the recovery, but when I restart it, I a triangle with an exlamation mark (!), and I can't enter bootloader.
So, is that it...?
Oook, so I got into bootloader, flashed the HardSPL ver to 2, trying to flash the radio again, and it's not moving at 0%...
I'm having a similar issue. I have cotulla's HSPL 2.08 and I cannot flash ANY rom, no stock t-mobile, no android, nothing! Someone please help us! I would hate to see our HD2's go in the drawer and be forgotten
T-MOUS
boymeetsfence said:
I'm having a similar issue. I have cotulla's HSPL 2.08 and I cannot flash ANY rom, no stock t-mobile, no android, nothing! Someone please help us! I would hate to see our HD2's go in the drawer and be forgotten
T-MOUS
Click to expand...
Click to collapse
By any chance was the existing ROM the 3.14 one?
CrowJA said:
Hey, so I have an HD2 that was flashed badly. No problem, enter bootloader, reflash, right?
Strangely enough, it was acting strangely, and would freeze while in bootloader mode (plug in, nothing would recognize it, plug out and USB is still on the screen).
I pull the battery, try again, and get to flashing the Radio, it stops at 96%, and then fails. Try to do the recovery, but when I restart it, I a triangle with an exlamation mark (!), and I can't enter bootloader.
So, is that it...?
Click to expand...
Click to collapse
Try and flash the stock (or branded) ROM, either by USB or SD method.
No, I installed that update when it came out, seemed to make the phone worse so I went back to 2.13
boymeetsfence said:
No, I installed that update when it came out, seemed to make the phone worse so I went back to 2.13
Click to expand...
Click to collapse
a friend was doing similar ...
he upgraded to cotulla's HSPL 2.08 no problem, but when updating to most recent radio to allow him to play with putty or energy it froze at 96% and now just boots to ! screen
will not acknowledge attempts to SDcard flash, and his attempt to flash with latest stock HTC rom fails at random spots between 1% and 45%
going to grab an old stock rom and try voldown/power into tricolor and downgrade I guess
may have had some success ... seems his sdcard was formatted as FAT not FAT32 (doh!)
put duttys latest on the card and sd flashed that no problems, then put latest radio on card and sd flashed that, made it to 100% but 10 mins later and radio flash attempt still sitting at 'update in progress' with bar at 100%
guess I'll try with HTC stock via sd now
no joy there either ... hangs after attempting to flash the first radio portion
RESULT! seems the root cause was cotulla's HSPL 2.08
Ran HSPL_2 went back to 1.66-HSPL
then installed stock 1.48.405.2 which flashed completely and cleanly
phew
hd2 died help!
i accidentaly flashed an incorrect radio rom and thats where my problem started. although it still vibrates continusly once i put the battery back but im not sure if i can revive this. please help me out.
I managed to flash the latest radio successfully with 1.66-HSPL in place.
I just bullheadedly continually kept reattempting to sdcard flash just the latest radio, maybe 15-20x it either locked or gave me RSA errors.
Just before I was about to fling it into the fireplace, it just *worked* for no apparent reason ...
Just whacked Dutty's latest on there, and now happily looking at the 'tap next to begin screen'
My phone has been running an Android NAND for a couple of months, and the other day it just froze and then on rebooting i get a plain white screen.
I can get to the bootloader and so far nothing flashes to it
HSPL - Critical Error
SD-CARD flash - red numbers or just continual loading
USB flash - sits at 0% then gets error
so what killed my phone?
and is there ANY way i can get it working again, if not...i will throw it in the bin or perhaps smash it up with a hammer and post a youtube video here...im that annoyed! I wouldnt mind if i continually flashed roms, but i didnt...flashed on Android NAND and now its dead.
Find yourself a standard Winmobile rom and radio for the HD2 (if yours is a TMOUS device make sure you choose the correct radio and rom type for this device) and flash them to your device. With a bit of luck your device should then boot up.
If you then wish to go down the Android route again then read and follow all the instructions on here to do so. Don't forget to make sure your battery is fully charged before you attempt the reflash.
Good luck, hope it goes well.
WB
hi,
the battery is fully charged, but this is the problem i have..i cannot flash anything to it via sdcard or usb both give errors.
htcjrs said:
hi,
the battery is fully charged, but this is the problem i have..i cannot flash anything to it via sdcard or usb both give errors.
Click to expand...
Click to collapse
Do you still have the Andriod ROM on your HD2? If so boot into MAGLDR by turning the HD2 off and then pressing andbolding down the power button. Then use the volume up and down keys to scoll through the menu and find recovery and press the send button to select.
If you nolonger have the Andriod ROM then I suggest running a Task 29 on your HD2 then try to flash the official ROM to your HD2. If you are still having trouble getting it to flash do not get discuraged just keep tring to get it to flash, heck trythe USB method for awhile then try the SD card method for awhile. For some unknown reason to me a lot of people here on XDA have been having trouble getting their HD2 to flash a ROM. But all of them just kept trying and eventually got it to flash a ROM. Best of luck.
tried and tried and tried again, anyone wants this brick for free, i will post.
htcjrs said:
tried and tried and tried again, anyone wants this brick for free, i will post.
Click to expand...
Click to collapse
Did you run a Task 29 on your HD2 as I mentioned in my previous post? I beleive this will help you out. Also if you still have MAGLDR on your HD2 you can try to reflash the Andriod ROM. If you no longer have MAGLDR on your HD2 then you can reflash HSPL 2.08 and reflash MAGLDR by usinig the bootloader and the try flashing the Adriod ROM. Just make sure the white bar of the bootloader screen says USB and not Serial before you try to flash anything.
T-Mac, I have this problem. It's not something as simple as with MAGLDR or CWM. You can't even get a bootscreen let alone flash anything from HSPL (everything sticks at %0) lol.
Dude, your best bet is to try go flash a custom WinMo ROM. I used one of Artemis' ROM's. It had a .nbh file so I renamed it to LEOIMG.nbh and put on my SD card (512-4GB max) and then boot to HSPL and it'll allow you to flash the ROM.
It'll flash correctly but once it reboots it'll go back to the white screen. After that, it'll be able to charge when off so let it charge overnight while off, then in the morning try unplug the USB from the phone then pull battery and put it back in then try boot. It worked like 3 times for me so you might aswell try it.
I personally think it's a problem with MAGLDR and maybe it becomes corrupt or something.
hi
im gonna try this now, but i have a small problem...it did flash HSPL and now it is on 2.08.000 and it wont flash back
its one nightmare after another.
made a little progress, when trying to flash stock rom from sd it just sits on loading.... no error but doesnt do anything else.
Try this turn your HD2 off and remove the battery for a couple of minutes and then put the battery back in. I do not know if the HD2 has a reset like this or not. But a lot of electronicsreset certain things when all power is disconnected. This may not help but what can it hurt. Best of luck.
htcjrs said:
tried and tried and tried again, anyone wants this brick for free, i will post.
Click to expand...
Click to collapse
I'll take it. In this day of T-Mo being sold off, I need a challenge to distract me and keep me happy
Hello, i have serious problem,
I was running Android GINGER... and after one restart i god 1234.... FAILED bla bla
After that i went to MAGLDR and tryed to reflash another rom but no succes
MAGLDR froze!!!!
I did TASK 29 on it and it removed everything, after this i am UNABLE to install MAGLDR 133 or any other on my HD2. its a 576MB from UK, using it in CROATIA.
HAD T-mob WIN 6.5, Android 2.1, and above mentioned 2.3.3 ver.
ANY IDEA HOW TO INSTALL MAGLDR AGAIN???
HSPL is COTULLA 2.08 HSPL
Did i bricked it? can i undo?
p.s. i did hardreset, didnt work.
CAN I TRY RETURN SPL and how to return to stock so i can try WMO6.5 again?
HELP i am desperate! help, payed alot for this phone, i am broke now without phone!
calm down man we've all been there at some point,
ok if you wanna go back to stock go to the htc site and download a official rom,
does your phone turn on?
can you get in bootloader?
if you can does it say spl or hspl ??
ops
i am sure you havent been there.
I GOT HSPL 2.08 by beppe and Cotula
I,ve tryed official rom, it starts counting, but at approx 10% it stops and bar goes red, and triangle with exclamation point appears next to it.
I OFF:... F**** it UP. i am so screwd!
-phone does turn on, and goes to white screen, saying htc and nothing
-i can go to 4colour bootscreen, sayes SERIAL and USB after i connect
ty for trying to help me
white screen hhmm Radio - do you happen to know what radio you have flashed, if not go here http://forum.xda-developers.com/showthread.php?t=611787 chose say 2.15.50.14 down load it, i dont have micro usb on my phone no more so you have to options put phone in bootloader wait for it to turn to usb and run the ruu for the radio, or extract it find the .nbh file and rename it to LEOIMG.nbh pop it in the phone keep holding volume down till u get a grey screen and follow the instructions to flash the radio, and then try again,
you said you had android before? did you use cwm or clk so you can recover??
oh and by the way i nearly bricked my hd2 on release day so i no how u feel lol
EDIT = you can try and flash the stock rom and start again, by using 7zip to extract the official rom, find the .nbh file, rename it to LEOIMG.nbh also pop it on a micro sd card smaller than 8gig (just to be safe) boot into bootloader and follow through that way.
Demon_man said:
white screen hhmm Radio - do you happen to know what radio you have flashed, if not go here http://forum.xda-developers.com/showthread.php?t=611787 chose say 2.15.50.14 down load it, i dont have micro usb on my phone no more so you have to options put phone in bootloader wait for it to turn to usb and run the ruu for the radio, or extract it find the .nbh file and rename it to LEOIMG.nbh pop it in the phone keep holding volume down till u get a grey screen and follow the instructions to flash the radio, and then try again,
you said you had android before? did you use cwm or clk so you can recover??
oh and by the way i nearly bricked my hd2 on release day so i no how u feel lol
EDIT = you can try and flash the stock rom and start again, by using 7zip to extract the official rom, find the .nbh file, rename it to LEOIMG.nbh also pop it on a micro sd card smaller than 8gig (just to be safe) boot into bootloader and follow through that way.
Click to expand...
Click to collapse
i sayed i had android on cwm, i tryed recover but magldr crashed, and since then i have problem loading MAGLDR.
RADIO FAILED TO UPDATE, i tryed that version that you sayed but it goes to 100% then shows again that triangle with !inside. F***** i am loseing my mind!
Your way of upgrading rom wont work, gray screen shows for a glich of a second and dissapears to 4colour bootscreen.
I wish i died! i ****ed all up.
BTW i bought a phone in uk and on the back of battery sayes only serial numbers in this order:
S/N99HJY005-2
35412003-754967-0
no imei, no nothing else if helps.
i am dead, payed 500$ for it last year for this amazeing phone and now i ruined everything.
ok im with you on what you have and havent done, to me it sounds like a hardware problem if it wont flash, do you have another micro sd car you could use to try and go back to stock??
did you format the sd card first ?
Demon_man said:
ok im with you on what you have and havent done, to me it sounds like a hardware problem if it wont flash, do you have another micro sd car you could use to try and go back to stock??
did you format the sd card first ?
Click to expand...
Click to collapse
I get it , how to do GRAY FLASHING THING, but i got RADIO EROOR
SAYES:
00018003
LEOIMG.nbh - FAIL
RADIO_V2 - RSA Fail
Update Terminate
UPDATE FAIL
this happends when the bar gets to the 100%
do you have access to another pc mate with a different operating system from yours??
are you connecting phone via usb to the front or back of the pc?
have a read through this thread im reading alos
http://forum.xda-developers.com/showthread.php?t=618084
Take out the battery and keep the phone off in a very cool air conditioned room for a couple hours (maybe even the refrigerator).
Put the battery back in and flash stock again.
edit: hmm. Just read that other thread, yeah you may need to jtag it...but I'd still try the fridge thing.
Edit2: worked for this guy:
nschoot said:
Sorry, for not replying before...
I put my phone in a ziplock plastic back and left it in the fridge for a few hours (I think about 8 hours or so). Then I booted it and tried to install the LEOIMG.nbh file from SD card... I kept it in the fridge while installing the image.
And somehow, it just worked first time!!
The image (from the first post of this thread) is a US demo version of Windows mobile, but I was able to install the regular ROM from the HTC site after this - without the need to keep it in the fridge.
Click to expand...
Click to collapse
demon_man said:
do you have access to another pc mate with a different operating system from yours??
Are you connecting phone via usb to the front or back of the pc?
Have a read through this thread im reading alos
http://forum.xda-developers.com/showthread.php?t=618084
Click to expand...
Click to collapse
ok what i did dunno, but this is whats happened
downgraded to spl 1.42 or something,
started official ruu winmo 6.5 got an error, cellphone shut down and now it wont even turn on.
Ty for all the help, realy realy realy thank you !!!!
I am off to bed, tomorow i will throw my hd2 to trash can!
davor.klobucaric said:
ok what i did dunno, but this is whats happened
downgraded to spl 1.42 or something,
started official ruu winmo 6.5 got an error, cellphone shut down and now it wont even turn on.
Ty for all the help, realy realy realy thank you !!!!
I am off to bed, tomorow i will throw my hd2 to trash can!
Click to expand...
Click to collapse
Which stock ROM did you flash?
either you have a bad flash and its gone tits up or its bricked, either way someone will be here tomorrow when u return
Demon_man said:
either you have a bad flash and its gone tits up or its bricked, either way someone will be here tomorrow when u return
Click to expand...
Click to collapse
STOCK ROM:
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
IT WAS WORKING BEFORE!!!
i left batery out for a couple of minutes,and now it goes to 4 colour bootscreen,
BUT! I have another problem, 1,42.0000 works, but its SPL, and if i try to go HSPL 2.08 PROGRAM CRASHES on my comp.
This is so fu**** up. I would rather send to someone who knows how to repair this. anyone interested?
Lost my will to live with this phone. i am suicidal! (joke, don't call social services)
davor.klobucaric said:
STOCK ROM:
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
IT WAS WORKING BEFORE!!!
i left batery out for a couple of minutes,and now it goes to 4 colour bootscreen,
BUT! I have another problem, 1,42.0000 works, but its SPL, and if i try to go HSPL 2.08 PROGRAM CRASHES on my comp.
This is so fu**** up. I would rather send to someone who knows how to repair this. anyone interested?
Lost my will to live with this phone. i am suicidal! (joke, don't call social services)
Click to expand...
Click to collapse
That is the correct ROM.
you need to flash it via SD instead of RUU, that way it will put the correct SPL on your phone without you having to do anything from you computer.
edit: to clarify, flashing via RUU it cannot replace your SPL version, but if you extract that file, then move the NBH to the root of your SD card, then rename it LEOIMG.NBH, then go into bootloader, it will recognize it and ask you to flash. hit power to flash and it will restore to stock SPL, Radio, ROM, Boot Logo, etc.. you're good to go.
your phone turned off??? is your battery dead??
orangekid said:
That is the correct ROM.
you need to flash it via SD instead of RUU, that way it will put the correct SPL on your phone without you having to do anything from you computer.
edit: to clarify, flashing via RUU it cannot replace your SPL version, but if you extract that file, then move the NBH to the root of your SD card, then rename it LEOIMG.NBH, then go into bootloader, it will recognize it and ask you to flash. hit power to flash and it will restore to stock SPL, Radio, ROM, Boot Logo, etc.. you're good to go.
Click to expand...
Click to collapse
I have tryed that, thank you for your response, it went well, spl went to rom fitting, BUT,
WHITE HTC sigh on turn on, 3 RED LINES ON THE BOTTOM showing radio, and other stuff, but it constantly restarts, it wont load win 6.5. anyonne know why?
Problem with clk/magldr
was trying to flash my htc hd2 EUROP with hd2 toolkit v 4.2.0.1 i follow this steps
1-i power off my phone
2-I press in vol down button and power button in same time phone now was in 3 color mode
3- i press in task 29 on hd2 toolkit this erase my phone completely
4-then i press vol down button and power button in same time again
5- i click in clk repartition and choose 200MB
6- what happen is after all this steps my phone start with htc image blocked in white and green and i cannot boot in fast speed mode like usually.
obs, im using spl-2.0.8 HSPL by cotulla.
does anyone knows how to enter in fast speed boot mode without clk or magldr cause ive tried with these they dont work,..i just only can run wm6.5 that is .....i need help please
You are sure, you have installed a recommended radio rom?
You should use the radio rom 2.15.50.14.
Send from my Leo using Tapatalk
A friend gave me his non-working HD2 to try fix. It would only boot to a white screen (no HTC logo). I was able to get to the multicoloured screen by pressing the vol down + power button. I tried flashing the latest RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship rom via USB but repeatedly it got as far as 1% then gave me an error 270 message. I then extracted the image, copied it an sd card and tried to install from the card. It seemed to go ok until it stopped at 4% then rebooted. I now get as far as a white screen plus HTC logo but no further. Any attempt to flash another rom from the sd card gives an error 00028002 'not allowed' then I get the multicoloured screen but the SPL has changed to 3.03.0000 from I think 2.08 but I can't be certain. Perhaps with hindsight I should have written down what the old screen said!
Any ideas to rescue the situation willingly accepted.
Thanks,
Geoff.
With SPL being stock, you don't have many options. You can try flashing HSPL and then stock winmo/other OS. Or you can try to flash original stock through SD.
By the way, if the device was originally broken because of an overheating issue, you might have to cool the device before attempting to flash anything.
Good luck.
rebgershon said:
A friend gave me his non-working HD2 to try fix. It would only boot to a white screen (no HTC logo). I was able to get to the multicoloured screen by pressing the vol down + power button. I tried flashing the latest RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship rom via USB but repeatedly it got as far as 1% then gave me an error 270 message. I then extracted the image, copied it an sd card and tried to install from the card. It seemed to go ok until it stopped at 4% then rebooted. I now get as far as a white screen plus HTC logo but no further. Any attempt to flash another rom from the sd card gives an error 00028002 'not allowed' then I get the multicoloured screen but the SPL has changed to 3.03.0000 from I think 2.08 but I can't be certain. Perhaps with hindsight I should have written down what the old screen said!
Any ideas to rescue the situation willingly accepted.
Thanks,
Geoff.
Click to expand...
Click to collapse
the first thing to happen when you sd card flash a stock rom, is that hspl gets removed, or if it isnt present, teh stock spl gets updated to teh one contained in teh new rom. Then the phone reboots into the new bootloader, and flashing starts.
What happened to you is it removed hspl, rebooted, and the fresh 3.03.0000 detected that the rom region/carrier doesnt match the phones region/carrier, and so failed.
That being said, teh fact that it wouldnt flash over usb is worrying, im leaning towards a faulty phone, but its early days yet.
Try setting hspl again, hspl4, set 3.03.hspl (not .0000) and try flash the rom you listed again, over usb, and report back.
samsamuel said:
the first thing to happen when you sd card flash a stock rom, is that hspl gets removed, or if it isnt present, teh stock spl gets updated to teh one contained in teh new rom. Then the phone reboots into the new bootloader, and flashing starts.
What happened to you is it removed hspl, rebooted, and the fresh 3.03.0000 detected that the rom region/carrier doesnt match the phones region/carrier, and so failed.
That being said, teh fact that it wouldnt flash over usb is worrying, im leaning towards a faulty phone, but its early days yet.
Try setting hspl again, hspl4, set 3.03.hspl (not .0000) and try flash the rom you listed again, over usb, and report back.
Click to expand...
Click to collapse
I've got a very similar problem to this. My phone only boots to a blank white screen. When I hold the volume down button when turning it on, I can get to the bootloader.
From there, sometimes I can set 3.03 hspl, but most of the time the phone freezes at 0%. If I try to flash a stock rom, it stays frozen at 0%. If any of these updates work, then it still only boots to the HTC logo on the white screen.
I'm trying to flash via USB, could this be a faulty phone? I wonder what could be faulty?
yeoldgreat1 said:
could this be a faulty phone? I wonder what could be faulty?
Click to expand...
Click to collapse
yea sounds like it, lots of reports of exactly this, some kind of hardware probably, though JTAG may help.