Related
Hi,
I've been using my xda for about a month now and have noticed it hard to keep the screen clean, it seems to be very greasy etc... Has anyone invested in a screen protector for this problem or is it not really worth it?
Also cause i have only had mine a month with limited use, has anyone who has owed this phone longer noticed it gets scratched from the pen etc after longer periods of time...?
I know not important questions but just something i've been wondering none the less. Thanks
Got a brando one
I wanted to ditch the case (as it's pants) so I got a brando screen protector. It was a real faff to fit and I still haven't got it a) square or b) without loads of [email protected] under it, but it does its job, it seems to be sensitive enough and I (probably) am too ham-fisted to judge how difficult it is to fit the thing.
Hope that helps.
I've been told the Martin Whatsisname Screen Protectors are really good.
I'm thinking about getting one of these.
Do they leave any marks when you peel them off afterwards? From the glue and stuff?
Hi Tom
They don't use any glue, so you can just peel them off with no problem.
They cling to the screen like clingfilm.
nothing else than brando! have used it on all of my previous devices .. just no comparison to the cheap ones on ebay ...
I would say screen protector is a must for me...I'm too lazy to pull out the stylus every time....a screen protector will allow me to tap with my fingers, nails.....or even a pen....in fact, I put a protector on almost every mobile phones, my previous PPC....
Fair enough, but at £8.50+ its a rip off!!! for a bit of plastic that cost 0.05p to make, they're laughing all the way to the bank....
Supply & Demand
Maybe. It's a quality product and it's still a lot cheaper than a new screen...
You pays yer money.
Maybe but im just not convinced, how can you decribe a bit of platic as a "quality product"? I have heard they are extreemly hard to fit properly without getting finger prints on them etc and you get air bubbles and it is really annoying if you even leave a few specs of dust underneath it...?
No one round the office here seems to bother with them. I dont expect with any device for the screen to remain untouched forever, i think it just comes down to normal wear and tear, as with everything. Just my views anyway, need to hear more about these things before i had over best part of £10.
I have seen a Martin Fields one and someone on here said they were good. Is it easy to notice its there if you have one installed?
I have bought some via ebay from screenprotector24 at £1.99 for 6 plus P&P. There was also a buy 2 get 1 free offer on too. I have never been a fan of screen protectors but I agree that with the Mini-S it is verging on essential.
I am more than happy with the quality of the ones I received.
Hope that helps someone.
Regards,
White.
I've been looking for some on ebay, what did you type in to search and find those? can you link me?
Hi,
Sorry, I'm at work and barred from ebay. www.screenprotector24.de may well work if I recall correctly.
Regards,
White
Brando screen protectors
Just because something's made of plastic doesn't mean it isn't quality. After all look at Pamela Anderson! (Sorry).
The Brando one I got is doing its job. Before I had the screen protector dirt would pile up and I'd be cleaning it 3 or 4 times a day. Now I don't have to. I was worried the screen would get damaged. I don't have to worry what I use on the screen or shoving it in my pocket.
Yes, you can tell it's on if you look. It looks like you've left the manufacturers sheet on but without a tab to remove it if it catches the light. Straight on, you'd be hard pressed to know it's there - honest.
I haven't seen the cheapo ones myself, I went on recomendations on forums from people who had more experience.
Also, Brando service is outstanding in my experience.
Right ok, i am thinking of getting one just for peace of mind. All i can find is Martin Philips ones on UK sites... Where can i find a decent priced Brando one on a UK site for a 02 xdx mini s? Can someone name a shop or link me etc?
Thanks
Go straight to the source!
I bought mine direct from the Brando site in Hong Kong... http://shop.brando.com.hk/screenprotector.php. It arrived within 6 days
I had the antireflective one on my old XDA2, but these ultra glossy ones are MUCH better. It was a fiddle to fit, but I honestly can't that it's there other than by looking for the edge. I've tried this a few times and I find the following procedure works well.
First off, you need to find as dust free an environment as possible. Choose a room that doesn't have any carpet, or fabric in it if you can(cushions curtains etc). Boil a kettle, and make the room a bit steamy. When the steam clears, it should take some of the dust with it.
The trick to avoiding dust is to be prepared. Get a good lint free cloth (lens microfibre cloth worked well for me) and a blower brush - small rubber bulb with a nozzle. Also keep some masking tape ready. Finally you will need a bright light - ideally a spot light, or if you've got low fluorescent lights under over your kitchen work tops, they are ideal. Wear latex gloves if you have any (you can usually get packs of 20 from poundland)
Stick some masking tape to the your worksurface, folding it back on itself, so that the sticky side is facing up. Use several strips so that you have an area two or three times the size of your screen.
Spend a few minutes polishing with the lint free cloth, and then set the phone down, face up, well illuminated (from above) and switched off!. Blow off all the remaining dust with the blower - make sure that no dust is stuck (might require more polishing) at this stage you have two hands free - in a minute you won't! Dont worry if some dust starts to settle back on the screen at this stage - it will be loose, and you can blow it off in a minute.
Next step - take the screen protector, and peel off the backing two thirds of the way. Keep the 'sticky' side face down so dust doesn't settle on it. It's helpful if you can crease the backing slightly as it's quite springy and tends to get in the way a bit. Be careful not to touch the exposed side though. If you're right handed you'll want the screen protector in your right hand at this moment.
The next bit, you might need to repeat a few times until you get it right...
Blow the last bits of dust off the screen (do NOT use your mouth - you will spit all over the screen). Line up the most exposed end of the protector - its a very precise fit, the edges will touch both sides, and the end should be lined up exactly with the end of the screen. If you push the protector under the plastic above the screen it will be short at the other end. You might need to lift and reposition a few times to get this right. Once you have placed the exposed end, put a finger on top and check the alignment. Now check for any dust. You might be able to blow one or two bits off, but if there is more than that, you need to lift off the protector, press it down onto the upturned tape to get rid of any dust, blow the dust of the screen and try again. The dust sticks to the tape MUCH better than the screen, and will not leave any residue on the Brando protector, so you can do this quite a few times if necessary.
The important thing here is not to panic. You will get dust, and will need to go round the loop a few times, but as you'll be prepared, there will be no problem. Once the protector is lined up, the screen is (temporarily) dust free and there are no bubbles (phew!) carefully remove the last of the backing film and holding the edges very lightly between your fingers (gloves help here) lay the last bit removing any bubbles. Once down, it is hard to get the protector off without damaging the edge so only do the last bit once you're sure there is no dust/bubbles.
Remove the front sheet and polish. With any luck, you should hardly be able to tell that the screen protector is there!
Thanks for those really comprehensive instructions! I'm going to order one from the Brando site today and will pick up the blower and lint-free cloth etc from Jessops (camera shop) this weekend.
Martin Fields overlay plus Question
Nice one on such detailed instructions!
I order a Martin Fields over lay plus today, they seem to have good reviews everywhere i have looked. They are slightly adhesive though, but as this is a "gentle silicon based glue" (so i hear) i think that means it will be fine on the screen.
Has anyone had experience on using these and what the screen is like after you remove them, any residue etc left afterwards? How long will it last roughly?
Thanks for any help guys!
I haven't tried this, but you could probably save yourself the cost of a blower brush by using a bike pump or better still an airbed footpump (you can use that one handed).
tom99, if you get a Martin Fields protector (or any other sort that uses adhesive) I'm not sure that its safe to use masking tape to clean it. The Brando ones stick to the screen electostatically, so its safe to clean them with tape (the instructions that come with it recommend scotch tape). If the instructions you get with your Martin Fields protector don't mention cleaning with tape, then I would miss out that step. Can you add a comment to this thread when you get it (or anyone else that has used a MF protector)? It might help others decide which protector to go for.
I posted a while ago about this with no response. I'd really appreciate some kind of input or advice or anything.
There are those of us who don't like screen protectors on our imates. Of course, after a year, this leads to those little, annoying scratches that seem to magically appear. There's stuff on the market to rub these out; one such product is Displex. I'd like to know if anyone has any experience with these products or any other methods of removing these tiny scratches.
If you haven't had a response in a year, I'd imagine that is because most people like the anti-glare and improved writing surface that a screen protector offers <shrug>
I know those scratches you're talking about but the first thing I do is to get a film for my new device to keep up the resale value.
I know this is a personal preference, but what do you have against films? I can't actually think of a downside to them apart from the first two attempts where you get dust under them and it annoys you for a week before you calm down enough to try it again =)
Maybe you could try one of these polishes and tell us how good they are, after all this information seems to be somewhat lacking ... ?
Amen to that. Actually the good brands (though a bit more expensive) of screen protectors are so easy to apply. I bought a couple of the ultra clear ones from Brando and i'm still on my first for close to a year now. Every now and then I clean the film with rubbing alcohol.
Since I own a few Swatch watches and most of them have already scratched plastic faces, I bought the little tube of scratch remover. It gets the job done but a lot of pressure is required especially if the scratch is very deep. Since my hands got very tired, I then used a Dremel. Word of advise, don't set the Dremel at a high speed because it will melt the plastic.
I don't know if the Magician's screen has some sort of anti-glare coating. When I tried to remove the scratches on my older pair of eye glasses, the anti-glare coating was taken off wether rubbing it manually or using the Dremel.
i've had only bad experiences with screen protectors. I guess that's what i get for being a cheap ass. Plus the jam is my first pda, so i never really realized how much of a problem those scratches really are.
I suppose the solution is to try the Displex screen scratch remover and then slap on a Writeshield AG. Thanks anyway.
I suggest you try first a very small area in a corner of the screen just in case the scratch remover will a a greater damage.
Good luck. Hope you do get your screen as good as new.
zerimar said:
I suggest you try first a very small area in a corner of the screen just in case the scratch remover will a a greater damage.
Good luck. Hope you do get your screen as good as new.
Click to expand...
Click to collapse
Absolutely. I once used scratch remover on my old XDA (Wallaby) and found it to be efective in removing the scratches. Problem - in the area where i removed the scratches the display was compromised - it looked like a prisma of kinds, kinda like when you little drops of liquid on an cathode ray tv - you could see little bits of red green and blue.
I think some kind of layer was removed causing this. So really try it on a corner before you go for the entire screen.
And another word, if you are not familiar with using a Dremel, NEVER use it for cleaning or polishing of plexiglass. I ruined a swatch with that. Used it even at a low speed, but the polishing wheel made the plexi so hot the watchglass actually looked like a bumpy road. Had it professionally repolished at a jewelers place, but by doing this the plexi had got so thin that i broke after a while...
Dremel and plexi - no good in my opinion.
i have a few scratches that came with my magician (i didnt pay a cent for the scratches ). let us know how you go.
BTW, has any one used car polisher for such a task? I heard (not sure how correct/accurate), that its possible to remove small scratchs from cds wih car polisher? I wonder if it works for lcds.
now how is man enough to try it out in there magicians hay :lol: :lol:
Can someone please tell me how to apply the screen protector that comes with the phone as it's just a large piece of clear plastic with no instructions how to physically attach it to the display!
It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.
It's a sticker that you stick on the screen. How hard is this?!
Just put it on. Work cleanly though, be prepared and do it right the first time.
Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out
I've now put on the screen protector that came with the phone, but it feels a little thin and flimsy.
I'd like to know people's opinion of other aftermarket brands of protector for this phone as I'd like to get something a bit better quality.
Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original
akash_84 said:
Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original
Click to expand...
Click to collapse
Did you try this new Brando screen protector, and if so, is it any good?
Also, has anyone else had any experience of after-market screen protectors for this phone?
OK I applied mine today - sorry for the delay but I was just waiting for a time I could be patient !
I ordered it from HTCDirect as they are the only ones that had in stock
Recieved it promptly the next day so Kudos to them on that...also the guy I kept in touch with over email (Carlos if I remember correctly) was great and prompt in my queries.
My main query was - does it have the SAME fitment as the original bundled one.
As you know, the bundled one covers the entire screen including the slider for zoom and camera
The answer was Yes, it was exactly the same fitment.
So when I opened the pack, I was a bit annoyed as it was clearly NOT the same fitment! It's close however, but the top of the camera where on the HTC is all the way round with a small hole for the camera, the Brando one is in a U shape leaving the top bit of the camera open.
OK onto application
Just like all Brando protectors, it is protected by two covers on either end with clear instructions - pull one side BEFORE application and the other AFTER application
Once the dust was off the screen and the original protector...
I did just this - and after several attempts of lining it up - and I note, it is very EXACT in lining up. Slightly out and you will have more black on one side from the screen than the other.
Peeled it off, applied it and smoothed it out - the latter bit was hardly needed as the bubbles just vanished which was great.
At this state, the protector looked smoked a little and not as clear as the original one.
Once I was happy, I peeled the top part - noticed one bubble near the end where the label to peel was, smoothed it out and the protector was as clear as the original one.
First impressions:
It does feel MUCH more durable
It has a very slight and I mean SLIGHT smoked affect in that it is not 100% transparent as the original one but this shows how good it is potentially in strength.
Usage is fine, I can glide over it with my finger and stylus without any issues. The original was a finger print magnet but this seems to not stain with it which is great.
Now the downside....
I think HTCDirect sent me a slightly duff one. It has clearly got markings on the top (once the top layer was off) which look like impact marks.
It is very tiny - almost like what happens to a screen without a protector after 12months
I'm not too fussed but feel a bit cheated. Its no use removing it now as I would have no protector on it during the replacement stages - not to metion I would have to pay to ship back etc.
For now, I am ok with it but if it bugs me, I will throw it away and put the original one on (I ordered 2 extras from Clove who as usual, got it to me instantly, good communications and speed in delivery).
The clove one has no marks at all so thats an option.
Hope this answers some of your questions but to summarise your question
Is it stronger?
Yes it is
Is it worth it?
If you can get one mark free - yes it is
Benefits?
It's re-usable, stronger, washable, and I notice it does not let as much light reflect of it - something I had huge problems with in the sunlight with the original one where I could not see the screen - I am not exaggerating!
Downsides?
Where I got mine from, it has marks on it - something that might just force me to remove it and go back to the original one
Also the camera does not go in a O shape but rather a U shape
OK during the submit button, I realsed the marks and the U shape was bugging me too much
I knew it was a matter of time that gap in the U would get clogged up with dust that would eventually get stuck around the U bit
Removed it and applied the original one I bought from Clove... I have two so if it does wear down, I can replace it
I know from experiance that the original one in the box that I applied lasted fine up till now (a month now since I've had my TD2) so I dont doubt that it will be worn out - May not last as long as Brando's guarantee of it outlasting te device but that's fine given the price of the HTC ones.
Applied it without any dust getting trapped (the main reason I had to buy these and the brando one)
I found those marks were actually dust that was already stuck under the protective layer - whether this is HTCDirects fault or Brando during factory release - who knows but I think as a lesson, I'm staying away from both and sticking to the original stuff.
Hope you make the right decision either way - for now, a brando goes into the bin
akash_84 said:
Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out
Click to expand...
Click to collapse
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually - big mistake.
so trashed the original one and waiting for the new brando to put it on. being a former iphone-user, i must admit that the diamond2 screen is pretty sensible to scratches. i thought that i won't be needing any protection, but i already have a few small ones...so a screen protection is a must-have now.
Should have read this first
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?
You'll be fine using it while its there - just be annoying to see the dust specs!
I ordered a pair of the original ones in the end as I was not happy at all with the premium Brando one - the look, feel and visibility was terrible
Reason I ordered 2 of the original ones is I was hearing rumours before the unit was even released that the original HTC one was not durable and would need to be replaced after x amount of months - having had mine for 4-5 months now and with heavy usage, I can report back to say the first protector of the two is still on there - still very clean with no stylus/finger/nail marks and still as durable as it was when I put it first on.
arsenal84 said:
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?
Click to expand...
Click to collapse
From what other threads are saying the screen should be treated with care. Don't push it hard and avoid impacts. Don't stick the phone in your back pocket! Some people have experienced damaged screens even after a short time.
Shouldnt put any phone in your back pocket!
The number of phones I have to fix or write off because they have had severe pressure on them - ie: sitting on them has increased 5 fold recently.
And lets face it...the countries population are not getting any thinner/smaller!
eXelero said:
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually
Click to expand...
Click to collapse
I know it is not recommended. but I use a small drop of water on the screen before applying the screen, wiping the water as it is squeeze out. The water takes the dust with it.
Hi
I've applied mine that came with the Diamond 2 and after a few attempts you can't see it is there. Ironically I fits so well I almost want to put another screen protector on top of it so it doesn't become damaged and need replacing.
Anyway a tip. Working in a dust free environment is the key. A bathroom is a good place. I have a hepa air filter (for hayfever) and this removes dust really well so run that for a bit which helps.
With all the care in the world dust can get underneath, I had a few specs, and they tend to cause a small bubble as the screen screen protector can't fit flush. I found it very easy to remove them. Have some sticky tape handy, this can be used to lift up the screen protector from the corner. Lift it back up enough to get to the spec of dust, and using another piece of sticky tape dab the spec of dust off the sticky side of the protector, then lay it back down.
Regards
Phil
Hairs
Fru T Bunn said:
It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.
Click to expand...
Click to collapse
I know what you mean I made an okay job of the one that came with it. The rubber case I bought of eBay came with one as well and made a right pigs ear of that. I think they need to be applied in a clean room
I've since bought some more off eBay so next time, I'm going to be a lot more careful!
Cheers, Rob.
I got 3 screen protectors with the original phone (2 of them as a gift). The first one was perfect except for a piece of fluff near the middle of the screen. I tried to remove it with a cloth(!!!) and ruined it. So I went for the second one, but at this stage the screen was not clean so I tried to use a microfibre cloth, which made it worse because it leaves even more fluff. I tried to fix it a few times and so now I have fluff inside, plus a bubble (the protector is a bit scratched) plus it doesn't stick properly on most of the sides and around the holes.
I am tempted to use the last one, but if I ruin it once more I am out of them. My biggest problem is how to clean the screen before sticking the protector. Will all the fluff come away when I remove the old protector? How can I clean the screen, knowing that the microfibre leaves fluff? Shall I blow with a can of compressed air?
I find magic tape is great for removing dust spots. Use the backing sheet to gently lift a corner then push the tape underneath to clean screen or protector as needed.
My favourite screen protectors are from Martin Fields. Really tough and easy to apply. Also, they are washable so if you do get a real dust problem you just take it off an run under the tap. Don't try that with the phone though...
I am currently not using a screen protector and I've noticed my screen is a dust magnet. I get an substantial amount of dust latching on to my screen (if it was just a bit I wouldn't bother). Is there any liquid solution I can use to make the screen more dust resistant? I am currently using lens cleaner and disposable microfiber cloths to clean my screen. Anybody else getting the same issue?
I just ordered a SGP crystal clear screen protector because I noticed how popular they were on the forums... but it won't arrive for another week.
maybe u should clean up in ur cave
If by cave you mean the city of Toronto (yes I collect dust while walking around the city), then yeah I'd like to. But all the mayoral candidates are crap and our politicians are corrupt as hell. Cleaning ain't gonna happen. Thanks for the suggestion though.
almaalma74 said:
maybe u should clean up in ur cave
Click to expand...
Click to collapse
Haha funny
But it's a real problem with a real solution (2.2-only)...
Go to settings
then click display
then scroll down
turn 'dust collector' off
that should do the trick!
This is my first time running into snarky people on xda, everybody else has been nothing short of helpful.
I'm noticing my phone screen is collecting more dust than all my other gadgets; I'm just wondering if anybody has had a similar issue.
There is no need to try to insult my intelligence. Thank you very much.
Turn your phone upside down when you place it on something, should do the trick lol
Sent from my GT-I9000 using XDA App
hahaha the replies made my day xD xD
Now that I think of it, I have never seen dust on the screen of my SGS, even though I live in a relatively polluted city. I guess it just gets wiped off by my fingers while, you know, I'm actually using the phone.
rasebo said:
Now that I think of it, I have never seen dust on the screen of my SGS, even though I live in a relatively polluted city. I guess it just gets wiped off by my fingers while, you know, I'm actually using the phone.
Click to expand...
Click to collapse
Thanks for letting me know.
Since I've got the phone I've been cleaning my screen with a camera lens cleaner solution. I'm just concerned I may have wiped off a coating off the glass, or the solution itself made the surface more adhesive. I'm sure it won't be a problem once the SGP protector arrives.
I know nothing about the hardware so please correct me... The screen is capacitive thus using electricity to detect touch. If for some reason the shielding is broken i can imagine it is a little bit static thus attracting dust. It could well be that my assessment is bs.
happens to my phone too.
My guess is that you have rubbed off our dissolved some sort of coating. I've had mine here in Vancouver (so the same Bell model, probably) for a couple of months and have never noticed anything I'd describe as dust, maybe some good old sweat and grease.
If you don't mind my asking, why were you cleaning the screen in the first place? Why use any sort of cleaning liquid if you're gonna clean it at all? Wouldn't the microfiber cloth, or kimtech wipes be enough? But again, why do it at all?
Sent from my GT-I9000M using XDA App
Recent study reveals germs and bacteria make your phone more dirty then a toilet seat.
I don't need a study to tell me that, the toilet seat is one of the cleanest parts of your house.
Still, you don't see people washing their money, their keyboard, or their dish sponge obsessively...
Sent from my GT-I9000M using XDA App
I guess you could try brasso gadget clean or something. I have never tried it but its meant to be anti static. Hope that helps.
Personaly i clean my phone weekly not for the germs but to remove crusts. I use lcd screen cleaner btw. But if you'll ever have to take care of a baby you will quickly get into the habit of cleaning everything.
this is now getting way off topic, as I'm sure the baby isn't playing with the i9000
but to keep that train of thought going, first time parents do tend to clean everything thoroughly (and hourly), but by the time you have your second or third you realize there's really no need to scrub everything with antibacterial sprays...
anyway, I'm curios whether someone knows if a capacitive touchscreen, gorilla skin, or the SGS's implementation of both has some kind of coating that's vulnerable to being taken off with lense cleaning fluids
http://www.engadget.com/2010/10/08/brasso-gadget-care-polish-review/ that's the brasso stuff. I have been using the sgp ultra clear. Its pretty decent thought nothing will beat the bare screen. And I have noticed it is slightly less responsive. Before with use the slightest touch it would register my finger. Now it seems like I need to apply abit more pressure.
Also when applying the screen protector be VERY careful. I wasted the first one because of dust getting underneath. very annoying so be careful and do it somewhere dust free and as quickly as possible.
Although I wash my face with biotherm homme exfoliating face wash twice a day, I don't have the best skin in the world. I tend to accumulate oils as the day progresses and my phone tends to share a bit of it. With that said, it was necessary for me to clean the phone every so often. The reason I used lens cleaner was because it was readily available and I figured if it was gentle enough for a camera lens, it should be more than apt for glass.
I'm just speculating there may be an anti static layer I've cleaned off. I wouldn't be surprised if there was (I mean they do sell anti static sprays). Atm, I'm just waiting for my SGP Ultra Crystal screen protector.
In the worst case I'll also try Brasso and/or an anti-static spray.
As for applying the protector, I think I'm going to use the steamy washroom method.
Btw, thanks to all who have added constructive suggestions and input, I really appreciate it.
I now have the same problem on my new Pixel 7 Pro I bought like a month ago. It's screen is dusty whenever I get it out of the pocket no matter what pants.
Searched everywhere and can't find anything useful. My first guess is some kind of static electricity. I've tried:
• other phones
• anti-static screen cleaner
• letting the battery die and keep it uncharged for like half a day.
• a bunch of different jeans/pants
• even tried vaccum cleaning my pockets and trying to pick up anything that's impossible to see with human eye by a lint roller and duct tape.
Putting on a screen protector film or tempered glass would be my last resort.
After 30 minutes in pocket it looks like this. It's really embarrassing when I have to get it out in front of other people. Also attaching a photo of my pocket so you don't think they are messy or something. Other phones do not have this problem in the same pocket
Hey was wondering how is the screen holding up. Do you guys having any scratches on them or anything? I'm debating on whether to take mine off
It's a very tough screen, mine is still in mint condition w/o a screen protector, but I never leave any sharp objects such as keys in the same pocket as my phone either.
No scratch at all, looks like new... (other than the rest of the device).
And I never used any "protective" thingies.
Cambxo said:
Hey was wondering how is the screen holding up. Do you guys having any scratches on them or anything? I'm debating on whether to take mine off
Click to expand...
Click to collapse
I've had my HD2 for 14 months and there are no scratches on it at all. When I first got it I saw the well known youtube vid of a guy trying to scratch his HD2 screen and failing. One night I was drunk and decided to show this to a mate, so I took a bottle cap and went to work with my screen, as hard as I could! We were both very impressed at the results (or lack of), but I noticed not long after that you could see where I had scratched it when I'd run my finger over it. If I wiped it clean then you couldn't see it at all. It was VERY feint, but it was there when smudged.
However, it's now 100% disappeared, even after major use.
I used to have a screen protector, but no longer bother. It's obviously always recommended not to put your phone in your pocket with keys & loose change etc., but this screen is THE BEST screen I've ever had on a phone.
I think it only needs a minimum of common sense and it will live for a looooooooooooong time!
Took mine off month ago, and very happy I did. It did nothing but lessen screen sensitivity and slightly dull viewing.
The glass on the screen can't withstand every stracth known to man, but it's pretty tough. Usually, the people with really messed up glass dropped theirs and the glass BROKE.
Here's the scratch test video and here's another thread about this where others share their thoughts and experiences.
I have just avoided putting in the same pocket as my keys, so far so good.
Wow that's pretty cool. I think I'm still going to keep one on though. To me its sort of like insurance. I may not need it often, but when I do, I sure will be glad I have it!
Sent from my HTC HD2 using XDA App
dung8604 said:
Wow that's pretty cool. I think I'm still going to keep one on though. To me its sort of like insurance. I may not need it often, but when I do, I sure will be glad I have it!
Click to expand...
Click to collapse
AHHH!!! They really need to move that damn thanks button, but thanks for that
To be honest, if it gives you peace of mind and doesn't have an adverse effect (sensitivity & brightness mainly) then yeah, keep it on.
I have my HD2 about 1,5 years now, and the screen didn't have a scratch at all. Unfortunately the back plate loses it clear finish, but that's acceptable.
Almost a year and no scratches whatsoever. I do keep it in a case whenever I am carrying it around, though. The only wear I can see at all are some indentations in the material on the top right corner of the handset.
Hi,
Got a cover, no scratch at all, like many people, i don't mix keys/smartphone screen, the best way to damage it !
almost a year and no scratch at all. I must say I guard it with my life.
it never leaves my sight and is always in it's original leather pocket.
I had a HTC Touch Cruise before and it was a plastic restitve touchscreen.
Even that thing was okay and usable after 3 years... It had many deep scratches but with backlight on you only saw them a bit and it wasnt a problem for the usability
The screen of the hd2 really needs some effort to get scratched. In my opinion a screen protector is useless, because the power that is needet to scratch this screen would easily cut the protector
But i also use the barely there case, to avoid scratches on the housing (put some tape on the corners to avoid damage from case on/off). The screen protector that was with this case gives me a better feeling on the touchscreen, its easier to glide ^^ and i dont have so many fingerprints
^^^
Fingerprints can be easily removed, you know
Mine is over 9 months old, still as good as new .
My secret is "The Magical Original Leather Pouch"
It never gets out of it, unless I want to use it
Is the camera lens cover made from the same material? Does it resist scratches as well as the screen?
I also don't use a screen protector. My phone is kept in a leather belt pouch, but is handled delicately (partially because it is expensive and partially because it is such a beautiful phone).
Got my TMOUS HD2 when they first came out, and screen is still perfect. I do keep it in a pocket by itself though, so no contact with keys or change.
Ive had mine around 14 months now, never used a protector and there's no problems at all with my screen. This is even after I stopped using the leather pouch a few months ago after getting an extended battery and even after dropping the phone a few times!
Almost one year without screen-protector and without case.
Not only one scratch on the screen.
I have two scratches on the screen, but you have to make effort to see them.
I took it to a sandy beach to read books every day all summer long, no protection whatsoever.
It's a great phone.