Related
Well, that's weird. My friends new XDA 2 is acting up. He lost his soubd trough speaker couple of days ago, and then it came back. Today it happened again. I have no clue what's going on, hard reset didn't help. Any suggestions?
TIA
Has he been using hands free headset? If its anything like the xda 1 the connecter is very problematic and prone to problems.
Yes, very frequently. Looks like that's it. He connected and disconnected couple of times again and now it works.
Hello everyone...
Well, I'm another victim but in this case my MDA2 is muted but not deaf...
I'll explain... Most people with this problem have said that they can't hear nor can be heard when they have this headphones plug problem (i.e. The plug when inserted got the contacts stuck so the system thinks the plug is still inserted).
But in my case the other party DO hear me (this is without using a headphones) but I can't hear them or the system sounds, music, etc. but when I plug my headphones I can hear all sounds with no problem.
The day it failed it was all of a sudden, no water, no bumps, no nothing... actually I was not even using my headphones, so the jack it's out of the equation...
Any ideas?
Well as a matter of fact, about three weeks ago I dropped my MDA2 to the pavement and it scratched the case a bit, but it was working fine for the last three weeks...
Do you think this may be a retarded symptom of the accident three weeks ago?
I'm starting to think the speaker failed or got unsoldered...
Any ideas?
Thanks!!!
Rayan
hi Rayan
i had the following problem: i couldn't TURN UP the volume.
i could move the volume slider, but when i took another look to see if the device did really set the slider to the volume i had set - nada - zero.
volume was down again.
if you encounter the same problems: make it short and give your device a COLD reboot. that was the only thing that did help and gave me back audio.
regards ize|man
Hi izeman,
Well, I even performed a hard reset to factory defaults and nothing!!!
And because of that I'm sure it's a hardware problem...
I just hope it's a simple fixable hardware problem... I'm just wating to get in touch with the guy's at gsmphonesource.com (I have sent SEVERAL emails and voicemails and no one has contacted me back!) :evil: (nice customer service huh? :? )
Well I'll let you know how this story ends... :roll:
Thanks,
Rayan
WHOOOHOOO!
I fixed the problem!!!
Since the guys where I purchased my MDA2 NEVER returned my calls and emails, I got desperate and fix it myself!!! (I know I void my warranty, but it was useless anyway since those *&^%$ guys refused to take my calls)... :evil:
Anyhow, I carefully opened my MDA2 and got all the way into the speaker (which is actually encased in a module with two small gold plated connectors on the top) and cleaned them both, on the speaker module and the motherboard where two matching springs are located. I even carefully pulled the springs to give them a little more "pressure" when assembled.
Well, what can I say... I'm very happy to have my sound back!!!
If someone want to go this route, please let me tell you that it was a pain in the buttocks just to pry open the casing, but now I know how to do it, so drop me a line if you need any assistance... Maybe I will document the procedure with pictures once I have some spare time!... :wink:
(Now I can get rid of my stupid wired headset... It's amazing how those damn wires get to tangle so much!)
Best regards!
Rayan
Sound problems
Hi Rayan,
Good to know you fixed it - I have exactly the same problem; speaker only works intermittently. :evil:
I'd like to take to up on your offer to provide further details; especially how your opened the case without damaging it. :?:
cheers,
Pete
XDA II, Scandisk 512Mb, Plantronics 3000[/quote]
Rayan's fix...
http://forum.xda-developers.com/viewtopic.php?t=8525&highlight=sound+problem
hi guys..
I was watching a video clip and suddenly I see I can't hear any audio from it. I was surprised.. I tried to soft reset it couple of times... but with no luck... I couldn't here any tap sound or even when the phone rings.. nothing sounds.. and finally I did hard reset... but in despair.. still the same problem. but when I try to shake my jam. I could feel something moving.. i don't know if any bit/piece is disconnected.. when i try to tap it hard at the speaker.. i could hear to the music and after few seconds.. its stops.. again..
Has anyone come across such a problem.. I think probably my speaker needs to replaced.. any suggestions or solutions to this..
I would await for ur replies.
kindly advise..
thanks
Iffu
i have the same problem to. Please Help!
This is a "common" problem with the Magician. Mine had it as well. I sent it for repair since it's still under warranty. Some ppl had the guts to open it and fix the loose contact themselves. So if you're not a techie just take it to your service centre for repair :-(
No sound?
Hi. i had a similar problem some days ago. no sound at all from my magician. i've discovered that the problem was that my magician thought i had headphones conected. a simple insert of a headphone jack and removal brought my sound back to live. No problems since than.
Just a gentle few bangs did the trick
After reading several suggestions and info about the speaker problem, I tested my 02 mini with a song. It played ok through the speaker. So the speaker works, but appears to not "Switch" on when being used as a phone. Anyway long story short - I hit the corner of it into the palm of my hand a few times and da da it works again. I also blew through the speaker hole. Someone mentioned that somewhere as well. Hitting into my hand seemed to provide enough impact without creating any damage.
Had same problem too, and sent it away for repair. Three weeks later and the repair company are sending me a replacement this week as apparently they were unable to fix it!
Fault appeared without any warning and I had been using the phone pretty heavily all day. All I hope is that the replacement will have a newer ROM installed to save my ineptness from screwing up an upgrade.
This Jam is a peice of shi#e. I bought one in February, had various problems with both speakers - regular earpiece was unclear and speaker phone was just too damn low in volume.
Some people claimed this was an exception, or that it was the ROM or whatever. Right......
Finally sent the Jam back for warranty repair in May- there were many other defects with the phone that accumulated. I had bought insurance as well so I told them to just replace it. The seller admitted that this (audio/speaker is a common problem in this phone)
I just got the insurance replacement today - yep ages later. This one has firmware 1.11 WWE.
Guess what: the speakerphone on this one (brand new replacement) doesn't work - at all. Not at all. This is brand new, out of thebox. Incredible....
What is worse is that I am going on a month-long trip in a couple of days, so there is no way I can get another one - and by the looks of it, even if I got a replacement, the chances are that it too is a piece of ****#e without a functional speakerphone. This I-mate Jam (or whatever the 50 name sit goes by) is just a low quality piece of garbage.
HTC/I-Mate is garbage company. There is no chance in hell I will be buying any future Jam or I-mate phone.
Hi all... This is my first post and and just want to say what a great community... Thanks...
Now for my problem. I have spent a lot of time reading posts and trying to solve my problems and haven't found anything that relates to what I am experiencing so hopefully someone might be able to help me out. It's a fairly long story but I'll try to give you the quick version.
I bought a new Softbank X01HT from an ebay seller. The phone arrived and when I tried use it all I would get was a bright white screen. I tried emailing the seller and got no response. (They sell several phones every day so I don't think he deliberately ripped me off, I just got a dud and the seller is too lazy to reply to emails).
I opened up the phone and investigated, my brother has an I-Mate branded version of the hermes so we swapped parts around and decided that the LCD/front ribbon cable was causing my problem. I ordered a new cable from cnn.cn. When it arrived I fitted it and thankfully the phone came to life. I did all the usual mods then, updated the ROM etc etc.
When I got it all back together the front earpiece was working but only very very quietly, I could hardly hear the person on the other end. The speakerphone works fine though. I tried hard reseting and even flashing a different ROM but this didn't help. So I opened the phone up again, thinking that I hadn't seated the earpiece properly. This time when I started it up again I got absolutely nothing from the earpiece. I also found that the front camera just doesn't work. I tried my swapping back the original ribbon cable, although I couldn't see what was going on I was still able to get someone to video call me, answer the call and still found the camera wasn't working, doing this I couldn't test the earpiece though.
I put the camera in my brothers hermes and it works just fine. We have swapped all parts around including main boards and they all interchange fine. I only strike a problem when I am using my camera with my main board. As for the earpiece we couldn't succesfully make it work in my brothers phone, but also couldn't make his earpiece work in my phone.
I have read the posts about the contacts on the earpiece, but trying this hasn't solved my problem. I guess there is a chance that the new ribbon cable I got is also faulty, but to have the same problem from two ribbon cables seems fairly unlikely. The speakerphone works fine and so does my bluetooth headset so I am fairly confident that it is not a software issue. I have used Black Satin ROM and now I have installed Schaps 3.6 (both nice ROMs btw)
Thanks to anyone who has spent the time to read this post, hopefully someone may be able to shed some light on it for me. I got the phone a fortnight ago and still haven't been able to use it properly and it's starting to drive me nuts.....
Thanks
Craig
Hello all!
First, thanks for an awesome forum! It has both helped me tweak my Wizard, and also get help when I have needed it.
Well, I have no choice now but to ask here. Last autumn, my warranty was almost up, and a wierd problem presented itself. The mic and speaker suddenly just stopped working! The sidespeakers still work, I think, because the phone rings when someone calls me. But the caller can't hear me, and I can't hear the caller. And there isn't a hint of sound in it, no static or noise, there simply is nothing.
As there were only a few days before the 2 year warranty was up, I ran to my dealer and turned it in. A few weeks later, the phone returned, working again. But now that I come to think about it, I don't remember if I got a replacement or if they actually repaired it... It looked a little like they handled it rough though, maybe it was another phone... Well, that's not important right now.
The same thing has happened again! Summary:
1. Mic & phonespeaker dead
2. Stereo speakers work under certain conditions
3. Wired headset that came with the phone works, both for calling and media
So it seems like a hardware problem. Please note, although I downgraded the phone to original, official Swedish Qtek 9100 ROM, it has been thoroughly tweaked and upgraded to a number of different WM6 ROMs - but all that has been working beatifully!
Still, what are the odds for the mic&speaker dying twice in a row, on different phones (i think the present one is a replacement)?!?
Question: Does anyone recognize this? Is there a possibility that it is software related, and maybe fixable? I have searched both the web and these forums but haven't really found any information on it.
ANY input would be greatly appreciated!
Additional information:
Qtek 9100 (Swedish), G3 model, WM6 upgrade successful (unlocked)
EDIT: There are no system sounds, which is wierd, because the phone can still ring. I thought the system sounds came from the stereo speakers on the sides of the device?
Hello all!
It is a glorious day to be alive!!! Or to have a fully functional Wizard, at least!
Lol - my topic isn't very old, and i reply to it myself with a solution (?). I Googled after the Wizard service manual, and found it right here on Xda .
In all honesty, i didn't do all that much. I just followed the disassembly instructions of the wizard about half-way through, to the point where you get down to the back of the motherboard. I poked and fiddled enough to locate the mic assembly, only to discover that the mic is soldered to the mainboard of the phone. So, i figured i'd just leave it be, because if the mic is really broken the motherboard needs to be repleaced, or a replacement mic needs to be soldered on there.
After removing A LOT of dust in there (honestly, i think the service center that had my device last time wasn't very careful with anything, even a screw was missing! ), i reassembled it. The flat cable running to the keyboard was also a little skewed, but that may have been me, anyway i corrected it too. Same with the speakers.
Long story short, after successfully reassmbling the phone, i fired it up, called my home phone and voila! I works!
Not much of a fix, as i don't really know what i did exactly, but dust, dirt and some bad connections/soldering may have benn the culprit.
All in all, i'm very pleased with my afternoon here. Thanks for stopping by .
epatnor said:
Hello all!
It is a glorious day to be alive!!! Or to have a fully functional Wizard, at least!
Lol - my topic isn't very old, and i reply to it myself with a solution (?). I Googled after the Wizard service manual, and found it right here on Xda .
In all honesty, i didn't do all that much. I just followed the disassembly instructions of the wizard about half-way through, to the point where you get down to the back of the motherboard. I poked and fiddled enough to locate the mic assembly, only to discover that the mic is soldered to the mainboard of the phone. So, i figured i'd just leave it be, because if the mic is really broken the motherboard needs to be repleaced, or a replacement mic needs to be soldered on there.
After removing A LOT of dust in there (honestly, i think the service center that had my device last time wasn't very careful with anything, even a screw was missing! ), i reassembled it. The flat cable running to the keyboard was also a little skewed, but that may have been me, anyway i corrected it too. Same with the speakers.
Long story short, after successfully reassmbling the phone, i fired it up, called my home phone and voila! I works!
Not much of a fix, as i don't really know what i did exactly, but dust, dirt and some bad connections/soldering may have benn the culprit.
All in all, i'm very pleased with my afternoon here. Thanks for stopping by .
Click to expand...
Click to collapse
hi epatnor,
I think the problem with your phone was a stucked microswitch in the 2,5 mm connector for the headset. I read about it here in the forum. Sometimes the switch stays in the closed position and the phone still thinks the headset is connected. Thats why all the sound is sent to the not connected headset and therefor your phone seems to be not working (unless you connect the headset)...
But removing the dust is for sure not a bad thing...
For the next time: I think there was an easier solution for this problem than disassembling your phone...
regards
huibuh_1
Thanks huibuh_1,
Yes this was probably not the smoothest way of "fixing" it. That said, the stucked microswitch theory would actually fit my problem well - I can see now that the exact problem I was having would arise if such a switch was indeed stuck.
However, I think that the problem would be more intermittent since I actually use that port now and then - especially since it's the only way to talk (besides using a bluetooth headset that is). And since I connect the wired headset now and again the switch is used and moved, I suspect that this would result in the speaker/mic coming online again maybe..? Temporarily at least?
All the same, thanks for replying - this might happen again and with your information I'm better prepared for it!
Today I noticed that my HD2 vibrates strangely, it sounds like a shaving machine when vibrating
I performed many soft resets, hard reset, then I flashed an offcial ROM, SPL, etc. but nothing works. I guess the problem is related with the vibration hardware.
I will be sending my phone to HTC service tomorrow, and let you know about the results.
Anybody faced the problem? Or any suggestion before sending the device to service?
Thanks...
vizier said:
Today I noticed that my HD2 vibrates strangely, it sounds like a shaving machine when vibrating
I performed many soft resets, hard reset, then I flashed an offcial ROM, SPL, etc. but nothing works. I guess the problem is related with the vibration hardware.
I will be sending my phone to HTC service tomorrow, and let you know about the results.
Anybody faced the problem? Or any suggestion before sending the device to service?
Thanks...
Click to expand...
Click to collapse
I remember (2months ago) that my vibrate works strangely, i hard reset and it works again perfectly!
There was some issue posted a few times where the camera flash was pressed in, and was interfering with the vibration somehow.
avivsworld said:
There was some issue posted a few times where the camera flash was pressed in, and was interfering with the vibration somehow.
Click to expand...
Click to collapse
I think I have the same problem, my camera flash seems to be pressed in (one side of it).
Is there an easy solution or should I hand it to the service?
Thanks...
avivsworld said:
There was some issue posted a few times where the camera flash was pressed in, and was interfering with the vibration somehow.
Click to expand...
Click to collapse
I am trying to find the older posts you mention, but no luck so far. Can you post the links to those post, I might be searching with the wrong keywords or something like that...
Thanks...
Vibration seems to be a big problem. I had the same issue. only solution: warranty repair. my phone was replaced by 02.
vizier said:
I am trying to find the older posts you mention, but no luck so far. Can you post the links to those post, I might be searching with the wrong keywords or something like that...
Thanks...
Click to expand...
Click to collapse
Can't seem to find them... anyway, the flash housing is nearly directly over the vibration motor thing, and if the plastic flash cover gets loose it could very well push the flash housing down (it's not very secure, pretty soft metal actually) and block the motor.
Just check if the plastic flash cover is pushed in from the rest of the body.
E: If it is, then get it repaired by warranty, as it's not worth opening it up to fix yourself and voiding your warranty.
avivsworld said:
Can't seem to find them... anyway, the flash housing is nearly directly over the vibration motor thing, and if the plastic flash cover gets loose it could very well push the flash housing down (it's not very secure, pretty soft metal actually) and block the motor.
Just check if the plastic flash cover is pushed in from the rest of the body.
E: If it is, then get it repaired by warranty, as it's not worth opening it up to fix yourself and voiding your warranty.
Click to expand...
Click to collapse
This is exactly what happened to my phone. The lower part of the plastic flash cover looks pushed in (I checked with another working HD2).
And yes, I handed the phone to the service today. I hope they do not break other things when trying to fix this issue
Thanks...
Vibration lost
avivsworld said:
Can't seem to find them... anyway, the flash housing is nearly directly over the vibration motor thing, and if the plastic flash cover gets loose it could very well push the flash housing down (it's not very secure, pretty soft metal actually) and block the motor.
Just check if the plastic flash cover is pushed in from the rest of the body.
E: If it is, then get it repaired by warranty, as it's not worth opening it up to fix yourself and voiding your warranty.
Click to expand...
Click to collapse
Hi,
My Leo stopped vibrating. I saw your posts and checked the camera flash. It was indeed pushed in. My warranty was not valid, so I tried to fix it myself. It was actually very easy. I followed a video showing how to disassemble the Leo . As soon as the housing is removed, we have access to the flash plastic cover. I've just snapped it in very carefully et voilá: the phone is back to its own self!
Many thanks for the tip. I would never have guessed it was related to the flash cover!!
Maria
doloresbf said:
Hi,
My Leo stopped vibrating. I saw your posts and checked the camera flash. It was indeed pushed in. My warranty was not valid, so I tried to fix it myself. It was actually very easy. I followed a video showing how to disassemble the Leo . As soon as the housing is removed, we have access to the flash plastic cover. I've just snapped it in very carefully et voilá: the phone is back to its own self!
Many thanks for the tip. I would never have guessed it was related to the flash cover!!
Maria
Click to expand...
Click to collapse
I am glad you fixed your problem easily.
My phone is still not back from the service
I have my phone back...
Finally, I have my phone back. The service report tells me that they have changed a part responsible for vibration. I checked the vibration functionality and actually it is working fine now. One surprise however is that the flash cover still appears to be pushed in.
Same problem
My TMobileUS HD2 is having the exact same problem - no vibration at all, even after hard reset. I also see the camera light's assembly is no longer correctly positioned in the body as it should be. It seems that the lower end is pulling into the body of the phone.
I treat my phone very gently, so I'm sure this didn't happen from rough treatment. Given that it's happening on a number of contiinents, this looks like a design defect.
TMobile demanded that I send it in for warranty service.
No Vibration Either
I have a TMOUS HD2, and I may have been the cause of this happening after reading this. I have no clue what you're talking about, but I have dropped the phone a few times and though the problem didn't happen right after a drop, it was just odd how it started. I had it set to vibrate when I pressed any keys, and then I was texting and it stopped. So... the only thing that I've seen that is a case that I only seem to have, my phone vibrates AT WILL, but when it does, it's very raspy and sounds very 'sick' and loud. So, I am not about to open my phone. I'm tech savvy enough, but in no way have I ever tinkered with hardware. I got my HD2 back in May, so I'm hoping that I have a warenty through HTC at least. I haven't contacted anyone about this, so is it my best bet to just send it to HTC or contact T-Mobile? And I have insurance, but I purchased my phone from Walmart. lol. Help?
I just came across this thread....
my vibrate function has been broken for several months and I've been delaying sending in for repair because I'm afraid of how long it will take (plus, it is the Australian version so I dont know if HTC North American will actually repair it under the current warranty)
I noticed that the bottom part of my flash does in fact seem to be pushed in. I'm considering doing what Maria did (opening it herself and popping the flash back into place). Does anyone have a sense of how long the repair takes from HTC?
Thanks
VIBRATION and FLASH PROBLEM
i'm having the same problem... lower part of the flash is pushed in. and vibration sometimes functioning sometimes not... but worst my FLASH NOT WORKING AT ALL...
Now having the same problem. This is a design flaw if I've ever seen one.
Same problem here, vibration was not working, but I just fix it!
I bought this T-Mobile HTC HD2 off eBay, and turns out that the vibration was not working!!
Once I found out this thread and the information about how the flash cover was blocking the vibration motor from functioning, I was able to confirm this was exactly what was happening!
So, I decided to open up the phone. I did not had to extract the entire screen piece out, I just had to unscrew the four screws and use a "shower suction thingy" on the screen to help pull it out but just the top part (in other words, half way out), because I only needed access to where the flash cover was, and then I was able to use a thin screw driver to PUSH back the flash cover to it right position. Then, after putting everything back to its place, the vibrator motor started to work!!!
Maybe I will put some "super glue" on the flash plastic cover to secure from being accidentally being push in in the future. Anyways, thank you everyone here on the forum for sharing your ideas!
As a late follow-up to mine... I called HTC and got an RMA number. Put off mailing it in for 3 weeks while I backed it up and arranged a temporary phone.
Mailed it on a Friday. Had it back with a replaced back on Monday.
I was EXTREMELY happy with the customer service on this one!
Missed 3 calls today... realize phone is not vibrating. Check different things that should make phone vibrate... nothing...
Flash lens is not pushed in this time... I'm about a month out of warranty now. Wonder how this is going to go over
I had this exact problem occur a few days ago, and I opened it up and simply snapped the light cover back into place carefully. But my phone still wasn't vibrating, so I opened it up again and I saw that the black rubber around the vibrate motor was causing the part that creates the vibration to get stuck. I simply just snipped a bit away so that the it was free and ta da! However the vibration is still weak compared to before so I don't know how to fix that? hope this helps you, and if someone knows why the vibration might be weaker than before the problem started any help would be great. thanks