Database Users

Bricked my S200 after installing jasper AKU3.3 plz help!

hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!

did try upload another rom from bootloader ?

did try upload another rom from bootloader ?
but first try a hard-reset

i don't know how to load a rom from bootloader (i allready have made soft and hard reset

no one could help me ?

1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!

i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?

while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.

this rom don't work, it give me the message
error 294 invalid vendor id

it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much

pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right

Artemis USPL v.01 upgrade error with 270 code, Please HEPL

Hi Profs,
there are some problems with a Artemis Update SPL (USPL) v.01. I've found this problem is several topic but there was no solution for it.
#1:
http://forum.xda-developers.com/showpost.php?p=1739577&postcount=413
#2:
http://forum.xda-developers.com/show...44#post1745844
#3
http://forum.xda-developers.com/showpost.php?p=1713596&postcount=1
The problem:
use USPL to get rid of the CID....count goes up to 100% screen shows black with green text, then pops to white. I need to do a soft reset to get it running again.
Then i use ROM Update Utility to update my p3300....and it still keeps hanging on 3%....damn. i get mad...!! Have read almost all here online...no virusscanner, no firewall....I use win XP.
i even tried without memory card and phone card....and nothing seems to work.......
ipl 1.14.0001
spl 1.14.0000
gsm 02.07.90
os 1.14.0.0
Who has any clue...?
With other words:
I've just got back my P3300 from repair, they changed the main board. With the previous main board I was able to upgrade the device and I was using the B&B versions.
But with this new board I'm not able to upgade the SPL. When I try to upgade the device after and start the start_uspl .exe the 10...20... ....100 my device become an interresting "blue screen" status and only the reset help to get out from this status. If I start the RomUpdateUtility.exe after the upgrade I got the error message #270
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
ExtROM version: 3.12.405.102
This is not the solution for the problem. I've tried it:
Plug in USB cable. Hold voice recorder button and press reset button. Bootloader will appear (Three color stripes). Then you may flash up ROM. (This works only for RUU installation types, not for PDAmobiz modified installator) Original english HTC P3300 ROM you may download form here: http://wiki.xda-developers.com/index...temis_Upgrades ....
Please help us to solve this problem....

Probably the same problem
This should be the same:
Hello POF,
I was directed to this link by Rudegar because I want to change the french ROM to English ROM.
The relevant data of my PDA is:
The version of the ROM: 1.14.406.1 FRE
Date of ROM: 9/27/06
Radio version: 02.67.90
Protocol version: 4.1.13.28
ROM extension version: 1.14.406.101
I tried exactly the way you described in the USPL_manual and everything went well till I got to a stage where I was asked to click the update button which I did. After then there was a window which showed "updating from current version to version 9.99". I was confused at this point but clicked "continue" and after this stage I got an error message and there was no longer a connection bw my PDA and my computer.
Thanks,
Jonat
Reply With Quote
http://forum.xda-developers.com/showpost.php?p=1784337&postcount=430

Also the same
Problem "lost connection PDA-PC"
Hi,
first I would like to thank you for goooood job to many people here !
Back to my problem. I have HTC Artemis (T-Mobile MDA Compact III), OS WM6 T-Mobile Czech version.
I ran start_uspl.exe on my computer. The part in DOS based screen seems to finish everytime OK, but finally the connection with PC is lost. Therefore when the PDA Phone ROM Update Utility starts cheking version the error "lost connection with PC" appears . PDA stay in "black screen" mode and only hard reset start it again as usual.
Does anybody have the same problem? Any idea, how to solve it ?
Thanks
http://forum.xda-developers.com/showpost.php?p=1773030&postcount=426

When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me

Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....

lenocs said:
then pops to white. I need to do a soft reset to get it running again.
Click to expand...
Click to collapse
What im saying is when it pops to white, dont soft reset it, just start the upgrade.

Anthony2oo5 said:
When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me
Click to expand...
Click to collapse
that what i also do When the screen goes white, don't restart. Just start your RUU

lenocs said:
Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....
Click to expand...
Click to collapse
Same situation as above. Depending on the Artemis, the screen might go white or black. Just don't freak out and keep on flashing the USPL. It WILL work and then reboot. Then you can flash the actual ROM you want.

Hello from an absolut newbie trying his first upgrade,
And I have just experienced the same problem than lenocs.
I have run start_uspl.exe, but when the screen is suposed to become white or dark, it becomes dark and the artemis is in fact totally off and connection is lost.
Anyway I supossed that it was because the scrren got black and I tried to run the update utility, but I´ve got an error (the terminal is disconnected or similar) and nothing happens.
I have had to soft reset the terminal and fortunatelly it seems that I still have my previous ROM and it seems that it works. But, do you know if there could be some "side effect" because the first step of start_uspl script?
Anyway I would like to move to WM6, so, any suggestion would be really appreciated.
Thank's a lot

When you restart, what is the USPL number?

Ooopppssss!
I didn't pay attention.
As I've said, I'm a newbie, so I was just woried because I thought I had "bricked" my new atemis.
How can I know now the USPL number?
Anyway I tried the star_uspl again (I'm a crazy newbie) and it failed. The artemis went off almost inmediately.
Thank you very much for your help
SpiggyTopes said:
When you restart, what is the USPL number?
Click to expand...
Click to collapse

solved ... at least for me
I think the problem is in SPL version 3.13 (or maybe anyone newer than 1.11).
Try different Artemis USPL - for me worked version from this page:
http://wiki.xda-developers.com/index.php?pagename=Artemis_DumpedRoms
It's very confusional, because file sizes and also dates are the same as in unfunctional version, but this one worked.
Hope it'll help you as it helped to me.

Maybe this can help you
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.

Rocheau said:
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.
Click to expand...
Click to collapse
do u have ur card in the phone while updating
you are suppose to remove the card

Problem solved (for me)
Hi,
i had the same problem error 270, 3% and lost connection with Activesync.
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
any way to upgrade was wrong ->> error 270
My good way was:
1. Downgrade to WM5 - original shipped ROM 1.12.405.1(link found on Wiki pages)
2. Under WM5 run USPL to unlock CID (now without any errors)
3. Final STEP - Upgrade to new ROM Artemis Touch 3.01 (without any errors by upgrade)
))
Now my Artemis seems to be OK.

I ran USPL with storage card inside the device...
no problem

switch SD card back to 2GB or smaller before USPL
Hi,
for me USPL did not work with my SDHC 8GB card but then I switched back to my previous 2GB SD card and then it works.
Perhaps the SDHC driver blocks USPL in some way.
Cheers,
Markus

i have been trying for 3 months
once i have upgraded my artemis to wm 6.0 everything seemed to be OK for two days... then the screen started to go black when i restart... şi downgraded to 5.0 but nothing changed... when i remove battery for a while, my arte works... when i try to do anything with it, the screen slowly goes black as if it is broken... please DO HELP ME! i am going to go mad... i have a new iphone, ihave i kaiser as well... but i miss my artemis very much...

Hello:
I have the same problem and realized hundereds have too. I have been checking in all forums and no asolution to it
The issue that happens to me is that I used USPL for upgrading to WM6 and worked, but now for the Touchflo it does not. Tried with all USB ports, tried with different computers and no good news.
The USPL msdos screen indicates that there is no connection at all in all percentage levels, then it bocomes dark and the 260 error whne installing the rom.
please help us soon !!!
we are in trouble!!

Same Problem : Screen shut down
Anybody can help us on this point ?
The only way to solve it is to remove the batterie during 30 min., then put it back and pray...
Then, for no reason, the screen shut down, a few minutes or days after
I've upgrade from WM5 to WM6 with the original Rom of HTC, it seems a little more stable but it shut down every 2 days when i'm lucky

trouble with hard spl

Im unable to upgrade the rom on my stock htc polaris.
im using vista with the 4.0 driver installed (dl'd from this forum).
I've turned off usb connection in win device center however when i try and install hard spl2 the progress screen sits at 0% and then times out with a 262 error.
does anyone have any ideas that can help me?

Use XP. I bet it works OK then...

4.0 Driver installed?
I have a stock Vista Ultimate, stock Device Center 6.1 and a German Orbit 2. It took me a while, but I finally managed it.
I didnt turn anything off, nothing. The only thing I had to change since the O2 ROM doesnt run unsigned stuff: the reg-entry to allow unsigned apps. Thats all.
Remove SD-Card
Connect to Device Center, wait till connection is fully established
Start the supplied RUU from HardSPL package
Follow instructions/click next/next/next...
Check your device, you have to confirm the execution of the loader
When the tri-color screen appears, unplug and replug, it'll upgrade the SPL and takes approx. 2 seconds
If you have no success at all: try to leave the device at the tri-color screen, quit the RUU and run it again, just leaving the device at the tri-color screen.
After a couple tries, I managed it and I'm happily running a stock HTC ROM instead of the O2 one.
Good luck, report back if it worked.

bencassie said:
Im unable to upgrade the rom on my stock htc polaris.
im using vista with the 4.0 driver installed (dl'd from this forum).
I've turned off usb connection in win device center however when i try and install hard spl2 the progress screen sits at 0% and then times out with a 262 error.
does anyone have any ideas that can help me?
Click to expand...
Click to collapse
u must be in normal status i mean just whe u r synching with vista and the ppc should be on and then start the hard spl (u don't need to go in bootloader by yourself) it will go to bootloader automatically and then upgrade will be successfull.
so
connect ppc with wmdc vista and then when connected and start hardspl

tried all of this but still no joy.
i think running it on xp would be fine but i dont have an xp box

bencassie said:
tried all of this but still no joy.
i think running it on xp would be fine but i dont have an xp box
Click to expand...
Click to collapse
failing that, go get an (micro)SD card and format it as FAT32
bung the RUU_Signed.nbh inside the rom update onto the SD card and name it POLAIMG.nbh (or to make it flash with no user confirmation, POLADIAG.nbh) slap the SD into your device and reset into SPL

Thanks A Million!!!!
Olipro said:
failing that, go get an (micro)SD card and format it as FAT32
bung the RUU_Signed.nbh inside the rom update onto the SD card and name it POLAIMG.nbh (or to make it flash with no user confirmation, POLADIAG.nbh) slap the SD into your device and reset into SPL
Click to expand...
Click to collapse
Olipro, You saved my life. After trying to flash my own cooked rom, my cruise wouldn't go beyond the splash screen. I used your tip and it worked!!!
THHHHAAAAAANKK YOUU!!!
Carlos

asking about,use the power from the USB port to charge the XDA

help me to break & solve this problem, maybe can also help the other members..
I tried to upgrade my XDA to WM2003SE everything goes right,
bootloader first time i still use v5.22
but when I soft reboot it freezes on the OZUP screen and
message ONLY FOR MICROSOFT bla bla bla....
i get this ROM from http://www.romkitchen.de/ ==> WM2003SE
then downgrade bootloader from v5.22 to v5.15,
using MMC (flash SD) continue to special rom 1.2,
and then cooked again using PC2002 by my own creation based from
romkitchen, what i want to ask is :
i cannot connect again via dekstop activesyn if i want to change
my ROM because my cradle cannot detect my charger?? but if i charge
directly, its work. What is the problem?
is my cradle/dekstop broken at the charger socket?
so what i need to do? just change the wire or socket or
i use the step like at http://wiki.xda-developers.com/index.php?pagename=WallabyCradleMod
if i prefer use the 2nd method, is that really OK? so just used cradle/deskstop, no need
power charger again if i want to change ROM to WM2003SE, because only can use via activesync?
after i change bootloader to v5.15, keep trying to change but only can via Flash SD Card,
i change to WM 2003 final, still same problem....after finish, only screen cannot enter the
menu or else, only boot screen until i am waiting for 15 minutes??? then change again to
WM2003 but using from http://www.romkitchen.de/tools, still same again....boot screen again...
haiyaaaa.....what happen?? i dont know, tired, always overtime to do this,hehehhee...
all my friends, help me...need your advice ^_^V
*now, i still used ROM from PC 2002,cooked again using PC2002 by my own creation based from romkitchen.
bootloader v5.15
Microsoft Pocket PC --> PC2002
Version 3.0.12039 (Build 11178)
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.24.00
Protocol version : 324e4
Model No.: PW10A1

I can not really help you, but i was also in the same situation, that i have had a device, that doesn´t work with any other ROM than PPC2002
Flashed several WM2003 ans the WM2003SE but non of them worked.
So i rest at PPC2002
Stefan

ow ow...
auch.. ok, thanks for the comment, i give-up,hehehe..but only for now,
take a rest first but i dont know for t'mrow, actually from 10 flashed,
i got 1 success, can got WM2003SE but with almost empty battery,
i know the inside and already set all, including i notice bluetooth icon,hehehe..
but how? i wonder that my sx56 with fake bluetooth, only icon
but after i charge my sx56 then i soft reset, its gone, back again with only boot-screen, after that, i can't find again WM2003SE ROM only lock with boot-screen, and ONLY FOR MICROSOFT..blablabla...
and about for my cradle/dekstop? how is it? can u give me solution to fixed it??
btw,thanks for helping, tips & trick hehehe...
i will keep trying to find/solved this problem by my own way ^_^V

modify my cradle/dekstop success
its working, i try to modify my cradle/dekstop with that steps (look at the top this thread), and it's work...actually not me who did it, but my friend,hehehehe....i ask his help and he agrre to doit, but all the risk is still at me, now i can charge and also syncronized to my notebook

no service... R:none G:none

OK heres my situation:
i upgraded from the stock o2 wm2003 to wm6 using the wiki ROM:
Helmi Windows Mobile 6 Profesional R0
CE OS 5.2.1620 (Build 18125.0.4.2)
now on bootup it says
R:none
G:none
D:5.60.00 WE
It boots up fine but....
i cant get any reception.- just says "no service"
i have also tried disabling and re-enabling "Phone" in com manager
Yes, i have done a soft reset, hard reset and ive tried XPLODE wm6.5 and my current wm6 ROM.
XDA unlock all reported a successful unlock.
HELP!!!
OK, i did the thing in the ROM post said:
"R None if you take out battery and turn it on without push the reset button twice.
SDK?"
and it works now but when i turn it on i have to press the reset button twice every time
can someone help?

first of all you must unlock sim under WM 2003, then remove the extrom of 2003 to gain adidional 16 mb of storage (resize DOC), then you must upgrade to radio version 1.15 and then you must try any WM5, 6, 6.1, 6.5 rom
so now flash your shipped rom, you may find preferred rom for your operator in my signature, then start everything from the beginning

ok, it has kinda settled down now, working as normal.
I have "unlock sim under WM 2003, then remove the extrom of 2003 to gain adidional 16 mb of storage (resize DOC)"
If i wanted to upgrade my radio version would i have to flash the ROM again?

no you can flash radio rom only without the OS

Jejeje
Hey Xplode i never was able to see that tools like unlock extrom and repart DOC works on my BA... it always shows an error! when i execute the unhide hide repart etc etc.. so I upgrade even tought jajaja.

they only work on WM 2003

xplode said:
they only work on WM 2003
Click to expand...
Click to collapse
are you sure xplode, cause i unlock my phone using the tools from the BA wiki and im using wm6.5.

ok,
i upgraded my radio to 1.15.....
but i still got the problem

none
I get this on my wm6.1 but normally gets sorted after a soft reset
HMM!!!!

Same problem, after updating from stock WM2003 to WM6.1PRO all steps done like the wiki steps except the ExtRom step, couldnt get the unhide, unlock program to run (missing file or libraries error), so i flashed sun's WM6.1PRO without the extra storage, now when i change the battery i get the NO radio bootloader, still im able to fix it by doing a soft reset, but the strangest thing is that im not able to use the wifi :/. So the thing is, when i turn on without the radio i can use the wifi, but no the phone(airplane mode), and when i do a soft reset, the radio shows and i can use the phone but the wifi doesnt turn on at all!. Any help please, dont make me choose betwen my phone and my wifi
PD: is not only the radio missing the i change the battery, also R:none G:none
I have a Qtek9090

very odd ,i can use my wifi when the phone is on.
But i went from wm2003 to wm6.5 to wm6
wierd....

so, is there a solution? I've got the same problem

Ops! Solved. Do a soft reset via the button.
(I always do a softreset via unlocking the battery and locking it again)

Every one here should know that there is no WM 6 for BlueAngel by microsoft. it is ported on BA by helmi_c and that >> R none and G none << Bug is in WM 6 from very first day. SO Whenever u pull the battery out u need to SOFT Reset the device after putting the battery on phone.(u need to wait to start the phone to reset, just put the battery and insert the stylus at reset point.)

there is no point discussing about this anymore. thread should be closed.

i have the solution about this problem, im recovery from it.
first of all, downgrade ur ba tu ship rom, and go back to upgrade 6,5 rom, after finis doit "WM5" hardreset.... search the way in wiki.
wala........its done and run normal r;none g;none not see again. have try it

This is an old problem... Rnone Gnone
solved by sticking your soft reset button after changing battery or a hard reset.
The Wifi-Phone problem is solved by buying a new battery. The Wifi module wont fireup because of the lack in power draw since the phone is using much of it.
Buying a new battery solves plenty of problem. even OS speedup because it solves the lag the "modules" (e.g camera/lan/phone/mmc) detection gives while in bootup or execution.
If you still have problems. We can always point to the wiki.
Have a nice day!
-SS-