Hi Folks,
Flashed me Wizard using the WST last August - forever afterwards stuck on bootup screens tho the bootloader and resetter could be invoked.. It sat there for months cos I've had a busy life...
Recently tried SD card read and flash, which it did with apparent success, but now the Wizard gives only bootloader screen, no bootup screens.
Looking to use SDwrite and other tools in ROMtools to write my original WST backups onto an SD card, and then reflash into the Wizard. (Can make RAW flash cards on the Wizard using ROMupdate_115)
Got the ROMtools software suite, but in Win XP I see a brief DOS screen - shows faster than I can blink, then returns to Windows. (Hum!)
Now wouldn't it be nice if the WST could prepare for possible trouble by adding a facility to write the Wizard's original software into a nice backup SD card in case Active Sync cannot work...
Ideas, anyone, or is this device fated to gather dust in my attic?
Peter
QTEK 9100 (Wizard 200 G4)
T-Mobile MDA Vario II (Hermes 300) with Dark Visions WM 6.5 ROM
Orange SPV M3100 (Hermes 100) with Dark Visions WM6.5 ROM
Related
hi folks, thanks in advance ,
i bought a mda compact , an sucessfully unlocked it with software from your ftp...ty.... So i upgraded this morning to a MDA Compact II, model no. pm200 and tried to unlock with the same tool , and it says device not recognised pm200.
i know its running windows mobile 5, any help to free the simlock would be greatfully recieved , all the best , oblivious. :lol: :twisted:
UNLOCK MDA COMPACT II / HTC CHARMER / PM200
Hello,
go to http://forum.xda-developers.com/viewtopic.php?t=33796&highlight=lokiwiz
Download lokiwiz.zip - HTC Wizard Unlocker v0.1
VERSION 0.1 !!!!!
follow these instructions:
1 - Unzip lokiwiz.zip to somewhere in your computer
2 - Copy EnableRapi.cab to your Charmer / PM200
3 - Execute the EnableRapi.cab in your phone. Wait for it to finish
4 - Guarantee that your phone is connected via ActiveSync with the computer
5 - Execute lokiwiz.bat and follow the instructions on your screen...
I've just unlocked my MDA Compact II with it, and it works.
Regards.
UNLOCK MDA COMPACT II / HTC CHARMER / PM200
Just wanted to confirm that i've had sucess unlocking my mda compact II (htc charmer). Followed shoptillyadrop instuctions and they worked a treat. Thanks for help.
Only, one comment to your instuctions - line 2 you wrote wizard rather than charmer.
Thanks again.
Will the SIM Lock be restored after I have performed a hard reset?
Thanks
Nase
No,
the Phone will remain unlocked. If you want to re-lock your phone, the same tool will do the job.
Regards.
Thanks for your quick reply.
The procedure sounds very easy so I will give it a try this evening.
Thanks
Nase
You are talking about NETlock, not SIMlock for a specific number (Prepaid), right?
I want to buy a MDAc2 from T-Mobile but have to use it with o2.
melino said:
You are talking about NETlock, not SIMlock for a specific number (Prepaid), right?
I want to buy a MDAc2 from T-Mobile but have to use it with o2.
Click to expand...
Click to collapse
Yes that is what I would like to do.
I guess that the Unlocker will remove any lock. Am I right?
Thanks
Nase
unlock mda2
work fine for me thank you :lol: :lol: :lol: :lol: :lol:
Has someone successfully unlocked (sim & Net) the t-Mobile German Compact 2 with a Tool?
PM200 UNLOCK PROBLEMS
HAVE USED LOKIWIZ VERSION 1 ,WELL HAVE USED THEM ALL WITHOUT SUCCESS ITS DRIVING ME MAD PLEASE SOMEONE HELP
GET''AN ERROR OCCURRED MESSAGE
THANKS
I've done it without problem. You list out your procedure done to see if we can help.
Hello. I had problem with my Mda Compact II T-Mobile UK. After I input Pin ti told that: Data Crashed conntact Your Service. I went to imei-check.co.uk and payed 20 GBP and in 5 minutes my Mda Works as a new one. Its the best way to solve this problem and problem with simlock too. Best regards !!!
A lot of people have unlocked their Charmer with out any problem. And there are at least two (including myself) who has flashed the Charmer ROM as well. Good if you can list out your specification and procedure that you have used that messed up your Charmer.
Usually, when you have the error message "Data Crashed conntact Your Service Provider", it means that the IMEI area has been messed up. And, the only solution to this problem seem to be to go to the imei-check.co.uk
Hey guys.
I have just got a Tmobile MDA Compact 2.
I cannot unlock it though.
I have tried V0.1 and V0.2b.
When my simcard (O2) is in the phone, it just asks you to enter the unlock code, and won't let you access any menus.
So I remove the SIM, install the EnableRapi.cab and then insert the Sim card. And click lokiwiz.bat on the PC whilst Activesync is running, I select U (have tried C aswell on V0.2b) and it doesn't show any errors, the phone resets, but the lock is still present.
Does anyone have any ideas ???
Unlock not working on my Charmer
Hi Guys!
I have followed the instructions carefully und copied the file EnableRapi.cab to my charmer, executed it there, made sure that Charmer is connected via ActiveSync, opened the file lokiwiz.bat on my PC, and waited until Charmer rebooted!
After reboot I inserted my SIM Card and the Result was a window that asked me after typing in my PIN for a Network Code!
I have tried all the Versions on the Unlock page, none worked! I have deactivated my AntiVirus Programms and Firewalls!
My Charmer is (still) locked from T-Mobile Austria! All I receive on my PC in the same Folder is an Output File called "Unlocked" which I cannot open with a program on my PC!
Thank you very much in advance for your help as otherwise I have to unlock it via Internet and this would cost me 30 BP!
;-)
Vibe
lokiwiz probably wont work on AKU2 roms because the OS is more protected. check your versions, Windows Build 14847.2.0.0 is AKU2.
dave106 said:
lokiwiz probably wont work on AKU2 roms because the OS is more protected. check your versions, Windows Build 14847.2.0.0 is AKU2.
Click to expand...
Click to collapse
that's exactly my version too...
can you keep me updated if there is a version that can unlock this type ?
thx !
Look what abzee wrote on: http://forum.xda-developers.com/sho...ght=could+not+update+itsutils.dll#post1039958
it took me 5 minutes to remove the lock using his instructions.
Thanks to abzee and of course to machinagod.
I used Lokiwiz03 yesterday with my Charmer. The Charmer is the german MDA Compact II with T-Mobile Netlock. It takes only some minutes. It was very easy to use-no problems.
Great Work and a very great thank you!
Hi there
I am new to this forum, I have purchased an SPV m600 on Orange from ebay, and I was woundering if I can upgrade the rom to T-mobile Vario. Has this been done before and will it work. If not please can soemone let me know where I can get other roms for this device. I am a t-mobile users, and the phone keeps on freezing when I enable push mail.
Cheers
The vario is the wizard while your device as you know is a prophet. Attempts to put wizard ROM on prophet "as is" were made with WM 6 but the results were unusable.
Chances are you will brick your device completely.
But note this: you push-mail problem shouldn't require a ROM change. All orange customization is in the ext ROM so try hard resetting your device, the soft resetting just after you finish all the calibration and stuff so the ext ROM wouldn't install. Then get the proper connection setting for T-mobile and see if it works.
Thanks for your help, are there any other Rom's I can install on that device ie, Imate or XDA. This way I will remove all the Orange setting of the device.
I have entered all the t-mobile gprs settings on the device, but it still frezzes every so often, but everything works still the web and email. I am not happy with the device fall asleep for 30 sec or so.
Cheers
Try the forum search for the Qtek 2.20 WWE ROM! This ROM is in english and have no Ext ROM from a provider such as T-Mobile or Orange! I think this would help you!
You must setup the connection data after finish installing manually but this isn't a big problem!
spv m600
Thanks for you help, if you come accross the link then let me know. I will do some searching over the weekend.
Cheers
hi
i have a QTEK S200. Today i tried to update my ppc with a WM6 version, but after 40min. the upgrade program crashed down.
After this it was impossible to enter in the main menu of the ppc. the ppc remains hanging on the QTEK screen. I've tried to enter in the bootloader with the color screen, to connect the ppc with my usb cable an the notebook, but my notebook does'nt find my ppc. And now the battery is empty (even connected with the usb cable on a working pc) and i can't switch on my ppc.
Any solutions?
Charge your Batterie and make Hard Reset. Charge VIA Caddy.
done. but the screen remains on the QTEK start page. Bootloader is possible and i get the 3-color screen but my notebook does'nt find my ppc... It's strange because yesterday everything was fine and the connection to my notebook was ok but in the 3-color screen i can't build a usb connection.
ok, problem solved. i've puted a new core on the ppc and now appears the old wm5.
how did you manage to get back to the old rom ? i am stuck on the qtek screnn and the only thing i can access is the USB flash 3 colors screen but my pc doesn't seem to the device...
any help greatly appreciate )
thx in advance
ben
do you have the problem with the SPL 3.08?
no I am in SPL 2.20... and IPL 2.09...
thanks for your help
please write the full ipl/spl number!
here it is :
IPL : 2.09
SPL : 2.20.0000
thx
finaly I manage to dowgrade it by changing my driver - the problem was coming from vista
important is to know, that the 3-color screen give the possibility to communicate with your computer (connected with usb).
so, you have the possibility to copy a new core on it. after that you put a new wm or you take the old one. in my case, the old wm5 was still on the ppc.
yesterday i was testing the wm6 in german but it was not really nice... so i work again with wm5 and wait till a complete wm6 solution is available.
Hi @ all
I need help!!! I have a Vario II and wanted to unlock it to use another sim, i downloaded a package called HTC_Hermes_SIM_CID_Unlock_v3a and started it. Ok now i have the big problem that when i start the MDA, only the Tri color screen appears. What can i do, do make it work again??? Maybe an upgrade, i have no idea.. Please help me, i wanna use my Vario II again, now it seems, that i can throw it in the rubbish bin. I'm absolutely hopelessly....
Ps. I also tried to update it to WM6 with the t-mobile software and with a normal one, downloaded from a link in this forum but after 1 % there is a update error 286 : The ROM Update Utility has encountered communication errors during the update process... This programm will guide you.. and so on ..
On the screen are the 3 colors and white and the Information: HERM 300 IPL-1.01 and HERM 300 SPL-1.40.0ipro
Ok thats all i know ^^
Firstly, have you tried the unbricking wiki page and followed the instructions. Be patient, read, reread and understand.
Secondly, what OS are you using (Vista, XP, W2K etc?) do you have the .net framework installed on that PC?
You (fortunately) appear to have HardSPL on the device by the sound of it so should be able to unbrick it if you follow the instructions on the wiki page.
Make sure you're using a non-vista PC with the .net framework installed and then try flashing ANY OS ONLY Rom in NBH format using the custom RUU wrapper. This should restore your device to some form of order.
Hello there,
i have a big Problem with my Vario II (Hermes) . My hermes starts not the Windows, but i can start the boot Screen with USB Connect.
I read many Wikis , but i don' t can update a new Rom.
My questions :
- in which order i must which programm start to update the ROM without ActiveSync
Herm300 IPL-1.01
Herm300 SPL-1.04
I hope you understand my english
Thanks
SpeedyGGG
Hello there,
i have a big Problem with my Vario II (Hermes) . My hermes starts not the Windows, but i can start the boot Screen with USB Connect.
I read many Wikis , but i don' t can update a new Rom.
My questions :
- in which order i must which programm start to update the ROM without ActiveSync.......................................
Click to expand...
Click to collapse
The easy way if you can get the bootscreen is to flash using a memory card,
there's plenty of guides.
copy hermimg.nbh into SD card max 1 GB and press Power+OK and rest with your pen in rest hole