Hello Everyone,
I have Tmobile HD2.I'd tried many times to install HSPL on my phone but everytime I get the same Error message.
Critical Error
Flow: 00000001
Error Code : 00000002
Description : USB connect failed.
My antivirous is disabled.
Can anyone advise what should I do ?? or Why is that message is coming up ??
Many thanks in advance.
samueladibusa said:
Hello Everyone,
I have Tmobile HD2.I'd tried many times to install HSPL on my phone but everytime I get the same Error message.
Critical Error
Flow: 00000001
Error Code : 00000002
Description : USB connect failed.
My antivirous is disabled.
Can anyone advise what should I do ?? or Why is that message is coming up ??
Many thanks in advance.
Click to expand...
Click to collapse
acitivesync runs ok?
YES, activesync is connected but I will try to reinstall it just in case if its the problem.
When your phone is in bootloader what SPL is listed, 2.10 or 2.08?
If 2.08 is listed, then HSPL should work and install just fine.
If 2.10 is listed, then HSPL will NOT work, and you will have to downgrade your version of SPL to 2.08, following this guide: http://forum.xda-developers.com/showthread.php?t=691779
Let me know either way.
~Jasecloud4
jasecloud4 said:
When your phone is in bootloader what SPL is listed, 2.10 or 2.08?
If 2.08 is listed, then HSPL should work and install just fine.
If 2.10 is listed, then HSPL will NOT work, and you will have to downgrade your version of SPL to 2.08, following this guide: http://forum.xda-developers.com/showthread.php?t=691779
Let me know either way.
~Jasecloud4
Click to expand...
Click to collapse
that would give a different error.
usb connect failed is usually down to trying to use a usb port that isn't directly mounted to the motherboard. confusion arises because flashing and active sync work perfectly fine from these ports, but hspl doesn't.
try to use a port around back off the pc, not in the case or a hub
im having the same problem as above, im running the HSPL from a laptop.... so im assuming the USB ports are not directly attached to the motherboard.... but i want to know what other option is there?? ive tried all three ports from the laptop, with no avail...
When you run the .exe right-click on it and run as administrator
im having the same problem, but i already installed 2.08 spl and installed energy rom CHT. im trying to change the radio and rom now but i keep getting that error message.
Critical Error USB connection failed
I was doing some reading here while troubleshooting the same error while trying to load hspl2 1024 via USB. I'm far from an expert, but the experience I just had may be of some use. For starters, I'm running Windows Vista 64 and the required Windows Mobile Device Center 6.1. After downgrading to 2.08, which worked fine, I setup active sync and ran hspl2 1024 as admin. After waiting about 30 seconds, Windows comes back with this critical error message. It seems that when the device sent to boot loader (tri colored screen), the USB connection is interrupted with windows and hspl2 1024 doesn't automatically try to reestablish connection, hence the error message. Anyways, I left the device at boot loader after error message popped up, closed hspl2 1024 and reopened it. This time it immediately recognized the connection with my device and installed. 30 seconds and done!! I hope this helps!!!!
griffinj01 said:
i was doing some reading here while troubleshooting the same error while trying to load hspl2 1024 via usb. I'm far from an expert, but the experience i just had may be of some use. For starters, i'm running windows vista 64 and the required windows mobile device center 6.1. After downgrading to 2.08, which worked fine, i setup active sync and ran hspl2 1024 as admin. After waiting about 30 seconds, windows comes back with this critical error message. It seems that when the device sent to boot loader (tri colored screen), the usb connection is interrupted with windows and hspl2 1024 doesn't automatically try to reestablish connection, hence the error message. Anyways, i left the device at boot loader after error message popped up, closed hspl2 1024 and reopened it. This time it immediately recognized the connection with my device and installed. 30 seconds and done!! I hope this helps!!!!
Click to expand...
Click to collapse
wow im gonna try but its giving me the same error and it suck im running window 7 and it reconize and then it gives me ther error an it stay plug in usb but doesnt recognize it
IT WORKED
hey all, i posted above, and for the life of me i couldnt get it to work. i know someone above posted to run it from a desktop, and from a port behond the CPU tower. for me, i only have a laptop and i couldnt get it to work. however, i used a different laptop and it work just fine!
i havent tried the "run as admin" option, but if you can, try a different laptop or a desktop...
THANKS FOR ALL THE HELP GUYS!
thebeach562 said:
hey all, i posted above, and for the life of me i couldnt get it to work. I know someone above posted to run it from a desktop, and from a port behond the cpu tower. For me, i only have a laptop and i couldnt get it to work. However, i used a different laptop and it work just fine!
I havent tried the "run as admin" option, but if you can, try a different laptop or a desktop...
Thanks for all the help guys!
i use hspl2 1024 it work
Click to expand...
Click to collapse
griffinj01 said:
I was doing some reading here while troubleshooting the same error while trying to load hspl2 1024 via USB. I'm far from an expert, but the experience I just had may be of some use. For starters, I'm running Windows Vista 64 and the required Windows Mobile Device Center 6.1. After downgrading to 2.08, which worked fine, I setup active sync and ran hspl2 1024 as admin. After waiting about 30 seconds, Windows comes back with this critical error message. It seems that when the device sent to boot loader (tri colored screen), the USB connection is interrupted with windows and hspl2 1024 doesn't automatically try to reestablish connection, hence the error message. Anyways, I left the device at boot loader after error message popped up, closed hspl2 1024 and reopened it. This time it immediately recognized the connection with my device and installed. 30 seconds and done!! I hope this helps!!!!
Click to expand...
Click to collapse
ok so im getting this same error message but when i try to install a rom not the hspl 1024. Lets see if this helps.Thanks!
hey guys,
i had the same problem before. for me it was because my sdcard. make sure you either remove it when flashing the hspl, because when you downgrade to 2.08 you have a LEOIMG.nbh file in your card, and it will interfere with the usb trying to flash. probably the same thing is happening with the problem with flashing the rom too. so remove the sdcard when flashing the hspl, but if you have a autoinstall file when installing a ROM, then either rename or remove the LEOIMG..bh on the sdcard before flashing rom or radio after.
critical error, same as everyone else
im on a 64-bit version of win7. i was having the same problem. i ran the hspl exe as admin and it worked. just wanted to confirm solution.
griffinj01 said:
I was doing some reading here while troubleshooting the same error while trying to load hspl2 1024 via USB. I'm far from an expert, but the experience I just had may be of some use. For starters, I'm running Windows Vista 64 and the required Windows Mobile Device Center 6.1. After downgrading to 2.08, which worked fine, I setup active sync and ran hspl2 1024 as admin. After waiting about 30 seconds, Windows comes back with this critical error message. It seems that when the device sent to boot loader (tri colored screen), the USB connection is interrupted with windows and hspl2 1024 doesn't automatically try to reestablish connection, hence the error message. Anyways, I left the device at boot loader after error message popped up, closed hspl2 1024 and reopened it. This time it immediately recognized the connection with my device and installed. 30 seconds and done!! I hope this helps!!!!
Click to expand...
Click to collapse
Thank you very much for that! I am now HSPL'd! Now on to custom roms...
Naveen
Related
hello i have an hd2 tmobile branded i cannot seem to hspl it because on 1024 i get usb conectiong failed but it does go on tri color screen and in hspl2 i get bad model id.
this is what i have on my tricolor:
PB81120 SS-B3
SPL-20.8.0000 8G XE
MICROP LED 0X05
MICROP TOUCH 0X40
PLEASE HELP =/
THANKS IN ADVANCE.
this is what you need my friend..
then you will be able to download the tmobile energy rom
http://rapidshare.com/files/368532303/HSPL2_1024_RUN.zip
HI,
I used the HSPL2_1024, selected the 2.0.0.8
After 10 min, of using Energy.Leo.23549.Sense2.5_TMobile_USA.Mar.26
I got an error, I recovered, but wondering what happened??
Just try it again. Make sure your drivers are all complete from Windows Vista or 7. Make sure you are running 6.1 Windows Mobile Device Center.
I am sure you have done this but make sure:
Plug in your phone make sure the drivers are good with Active Sync on.
When you get into HSPL2_1024 and let it run your device will be found again in USB mode. Just to make sure the drivers are loaded correctly.
Flash - reboot and then flash the Energy or whatever USTMO compatible cooked ROM you like. I think there are only 2/3 that work with the ROM 2.08
Sometimes it just takes retracing your steps to get it to work right.
good luck.
I didn't want to make a new thread for this and clutter up the board, I'm kind of a noob to XDA you see. I just bought a Tmobile HD2 and downloaded and applied the HSPL linked in this thread, it all worked fine. My problem is: Will installing the 2.09.51.03 radio on my tmous HD2 hurt it? Was the 2.09 radio meant for the htc hd2 which has a different radio?
My main goal is to get Artemis rom on it.
Thanks for your time.
Lazarpandar said:
I didn't want to make a new thread for this and clutter up the board, I'm kind of a noob to XDA you see. I just bought a Tmobile HD2 and downloaded and applied the HSPL linked in this thread, it all worked fine. My problem is: Will installing the 2.09.51.03 radio on my tmous HD2 hurt it? Was the 2.09 radio meant for the htc hd2 which has a different radio?
My main goal is to get Artemis rom on it.
Thanks for your time.
Click to expand...
Click to collapse
The .51 radios are meant for the European spec and will not work on a TMOUS based rom AFAIK.
yeah i have installed mobile center twice straight from microsoft, my phone is synced with it, i run the 1024 it says connecting 5 min later says usb connection failed my phone does go into the tri color screen with the USB at the bottom =/ please really help
S3BAZ10 said:
yeah i have installed mobile center twice straight from microsoft, my phone is synced with it, i run the 1024 it says connecting 5 min later says usb connection failed my phone does go into the tri color screen with the USB at the bottom =/ please really help
Click to expand...
Click to collapse
try different usb ports and remember to right click 1024 and 'run as administrator'
After using the HardSPL I could not get my phone to sync either... So Just put your phone into bootloader mode. Turn off phone, power button, volume down hold till tri color screen comes up. Then just run the RUU an it will flash your phone. Only NRGZ rom works.
richsark said:
HI,
I used the HSPL2_1024, selected the 2.0.0.8
After 10 min, of using Energy.Leo.23549.Sense2.5_TMobile_USA.Mar.26
I got an error, I recovered, but wondering what happened??
Click to expand...
Click to collapse
You have to choose. 2.0.0.8 HSPL
msmith1991 said:
this is what you need my friend..
then you will be able to download the tmobile energy rom
http://rapidshare.com/files/368532303/HSPL2_1024_RUN.zip
Click to expand...
Click to collapse
Would anyone happen to have a mirror to this link, or could some kind soul possibly upload it? This one seems to be broken. It would be greatly appreciated.
Update...I found it.
yeah notinh still not working ive tryed all ports, im running windows 7 64bit.
I'm recieving the same error. Windows 7 x64, MDC is latest 6.1. Tried from both laptop (Win7 x64) and desktop (Win7 x64). Phone goes into Tri color screen, says "USB" at the bottom. Windows notes new driver, updates, then HSPL2 for 1024 Leo gives "Critical Error" and bombs out. Bummer
UPDATE: Fixed it. Did a hard reset on the phone, tried again, and now HSPL flashed successfully. Now, on to the cooked ROMs
Worked for me on win 7 x64... No issue with HSPL2_1024_RUN file I got by browsing this site... It did freeze on me during RUU, but I just rebooted and ran it as admin whilst not touching any other program in windows until it was done and it worked.
zoth said:
You have to choose. 2.0.0.8 HSPL
Click to expand...
Click to collapse
I believe you are to choose 2.08 to install HSPL
And you choose 2.08.0000 when you want to uninstall HSPL, for warranty and such.
well i had done a hardreset before but nothing, i tryed it on my laptop and it worked fine, guess it was my PC =/, thanks anyways to all you who tryed to help.
S3BAZ10 said:
well i had done a hardreset before but nothing, i tryed it on my laptop and it worked fine, guess it was my PC =/, thanks anyways to all you who tryed to help.
Click to expand...
Click to collapse
Please change the Thread title by adding {Solved} or something like that to note that your issue has been resolved.
hi guys, I tried all of hspl2 (1024) version for TMO US htc HD2 but it does not work at all. Pls help me.
Critical error is showed up by hspl2
My Phone softare information;
OS 5.2.xxxx
Manila 2.5.xxxxx
Rom v 2.10.xxxx(82076) WWE
Radio 2.08.xxxxx
I still use stock rom which is TMO US's shipping rom
I checked whole Hspl2 (1024) but doent work, Pls help me,
Moved you over to General. HSPL questions should have been posted in the hspl thread already open buddy.
Peace,
Josh
ok. I'll do it. thank you
When i try to install hspl3 an error message comes up saying "This application has failed to start because RAPI.dll was not found. Re-installing the application may fix this problem.
I tried switching usb ports, sitll don't work
I booted into bootloader, and tried connecting with disk drive, still same error message
Sometimes my computer wouldn't let me install the drivers, but i tried a laptop at my friends house, it's saying the same thing on mine, with the drivers installed
Please help, im trying to install android nand
My SPl is 2.10.0000 and i know hspl3 supports that
Try this one, Extract the zip and run as administrator.
Do as the post above tells you too. Right click on the DFT utility and run it as administrator this is a must or you will get a error message everytime when trying to flash HSPL.
Rapi.DLL error is usually associated to activesync /wmdc not being up to date. Go download and install activesync for XP or wmdc for vista or 7. Yes. It's probably already installed, install it again.
Thankyou very much guys, it worked!
Hi
I have hd2 and display white
When I try (vol- + pwr) I see "spl-3.03.0000 XE" I try change spl but I can't
When created goldcard and write this card leoimg.nbh I see white screen and "Loading..." and nothing to do ...
Any idea ??
sorry my bad english
You need HSPL4 to downgrade your spl.
Yes, but I don't know how ?
When I try write hspl I see this error
"critical error
Flow: 00000005
Error code: 00000005
Description: Bad SPL version"
Where I found correct spl version ???
Of course it will say Bad SPL version.
You need HSPL4 .. This one : http://forum.xda-developers.com/showpost.php?p=5279236&postcount=4
Also, run as administrator, always do so.
When I connect hd2 I see "usb" and I choose hspl but then nothing to do
"please wait while installing HSPL..."
Leo stay 3 color "usb" but not writting to him
If you're still on Bootloader (tri-colour) screen then the installation is not happening.
Try clicking on cancel, rebooting your device and trying again. If the problem presist, tell me what Operating System you have.
This same problem, I have Windows xp 32 bit
I tried on 3 computers this same system (xp) and still hspl not writing...
Maybe you don't have the required drivers?
reinstall ActiveSync, the drivers sould be automatically installed with the package.
But if you were on Windows 7, the process would've been much simpler.
I was reinstall ActiveSync and not result, problem still this same
Maybe try it on a Windows 7 ?
I've looked for similar problems, but all were reporting that it worked after another try.
try it on Windows 7
this same on WP7 and error
"critical error
Flow:00000006
Error code:00000014
Description: Unknown"
Is your phone a t-mobile or european.
Based on what your device, download the corresponding original Winmo ROM and flash normally through usb ..
The phone is european
Winmo Rom, you mean Windows Mobile ??
I tried write original Windows Mobile 6.5 with this page http://firma.sunnysoft.cz/htc/ or www.htc.com
and "1%" then error 270 update error...
I have a question, what was the last thing you did .. before your device started doing this?
Precisely because I do not know this phone and I do not have client contact with him
well, I have told you what should have fixed it .. but since it hasn't been fixed, it seems that the client has done some real "sh&%" to that phone .
I'm at the end of my knowledge, maybe other members can help you?
Furthermore, you are on the Original SPL which means you can get HTC's warranty (if it is still under it)
There is no guarantee in any case, thank you for your time
My english Not good you must orginal Rom Flash in usb Mode go to htc com and Download withe your imai your specifik Stork Rom and flash over usb Mode -down key on your smardfone on start(usb Mode)and Flash storkrom.
Sent from my HD2 using XDA Windows Phone 7 App
None of this, I tried
Hey there Community,
I really don't know much about mobiles, especially the HTC HD2 and flashing ROMs,
but somehow I got Android to work on my HTC HD2 1 year back and now wanted to sell my phone because I got a new one.
Therefore I needed to set up the factory settings and get Windows Mobile 6.5 back on my phone..
Unfortunately I failed hard while following the instructions of a tutorial that said I only needed to rename ruunbh to leoimg and put it on my SD-card and so on.
Halfway the update was interrupted and since then Iam getting "00028002 Not allow" error and can only boot to the bootloader saying "Upgrade ROM code error Please try again" And the usual things in the red disctrict and at the bottom it says that I got an USB-connection which seems to be wrong, because I can't see the device and so on.
I tried to install HSPL4 but it failed due to no USB-connection.
So what can I now do to make it work again? Iam really frustrated
Flashing image from sd is all good if it original correct country/vendor rom, if not you get your problem & things can be tricky as HSPL was replaced with standard SPL so care must be taken.
Either find a correct Vendor/country (CID) ROM for your HD2 or get it in bootloader & able to flash HSPL.
Would of thought for resale a good Android build would be more desirable.
I know what you mean, but the problem is that I just don't know what to do..
My phone is not branded or anything, so I couldn just go to htc.com and get me the newest winmo Rom?
The Problem is, what to do then, exactly?
It seems that I can't flash anything because I dont got usbconnection..
So no idea to original ROM country vendor !
usb connection may be due to driver issue on PC, install Activesync if on XP or WMDC 6.1 for Vista & Windows 7 then retry connecting hd2 via usb .
*Also make sure you know your version of HD2 & be aware of .51 radios killing US T-Mobile HD2s.
Try to flash 2.08.HSPL only (also in HSPL4). It is enough. You can also try these drivers to fix your USB connection.
And here you can find offical ROMs.
Drivers linked above are not suitable, install activesync or WMDC is best option.
Finding original ROM is not going to be easy if you have no clues to origin of handset ...
Also, just cost you don't "see" the phone from the p c doesn't mean you don't have a USB connection.... it will never show up in your drives list like it does when an os is running, and activesync (or wmdc) will also not see the phone when it's in bootloader.
If the phone shows "USB" (and your PC may even "ding" when its plugged in, that's all you can expect unless you look deeper,, into the hardware list, for example.
What does hspl line say?
I'd do....
Hspl4, choose 3.03.hspl (NOT 3.03.0000)
Flash unbranded 3.14 rom from USB
Report back.
I have same story - 00028002 not allow+no usb.
no one stock rom can be flashed.
completely lost and no idea what to do.
Hi!
I've been using an Andriod NAND for like 2 years now and decided to upgrade to IcecreamSandwich. I installed HSPL 2.08 which I believe I had before anyway. Then I tried updating my radio but I get connection error 262. Apparently my phone wouldn't synch with WinMobileDeviceCenter. When I bootload I get serial and when I plugin it changes USB. But device doesn't get recognized. after rebooting I can start my Android no longer - MAGLDR 1.11 says ...boot mount failed. So I'm stuck in MAGLDR 1.11 and I can't ever restore to WinMobile original ROM. Any ideas?
slickie said:
Hi!
I've been using an Andriod NAND for like 2 years now and decided to upgrade to IcecreamSandwich. I installed HSPL 2.08 which I believe I had before anyway. Then I tried updating my radio but I get connection error 262. Apparently my phone wouldn't synch with WinMobileDeviceCenter. When I bootload I get serial and when I plugin it changes USB. But device doesn't get recognized. after rebooting I can start my Android no longer - MAGLDR 1.11 says ...boot mount failed. So I'm stuck in MAGLDR 1.11 and I can't ever restore to WinMobile original ROM. Any ideas?
Click to expand...
Click to collapse
if you put the phone in bootloader (4 colors Screen - HSPL 2.08 exc..) and show up USB when you connect it to the PC, it should be recognized from the application flasher, no PC.
Try to go in bootloader and when you connect the phone to your pc and when show up USB try to upgade and flash MAGLDR 1.13, (no MAGLDR 1.11 the old one) the last one.
Are you sure you used the right Radio for Leo?
thanks
eclyptos said:
if you put the phone in bootloader (4 colors Screen - HSPL 2.08 exc..) and show up USB when you connect it to the PC, it should be recognized from the application flasher, no PC.
Try to go in bootloader and when you connect the phone to your pc and when show up USB try to upgade and flash MAGLDR 1.13, (no MAGLDR 1.11 the old one) the last one.
Are you sure you used the right Radio for Leo?
Click to expand...
Click to collapse
When I try updating either the radio or MAGLDR in the install instructions there is this step2 where I have to establish an activesynch with my phone. I can't. So when I run the update it starts but progress stays at 0% both on PC and phone screen. After a few minutes I get error 262.
I'm trying to install radio 2.15 from Jayce Ooi's Paradise
Forget about active sync, you will never get an active sync connection unless win mo is running,, ,that'snot what the instruction to "get an active sync connection" means. It means get a USB connection, which uses the active sync drivers.
Try different usb ports,,do not use a front mounted usb port,only theones inthe back of the machine.
samsamuel said:
Forget about active sync, you will never get an active sync connection unless win mo is running,, ,that'snot what the instruction to "get an active sync connection" means. It means get a USB connection, which uses the active sync drivers.
Try different usb ports,,do not use a front mounted usb port,only theones inthe back of the machine.
Click to expand...
Click to collapse
Why do I get this connection error then?
I did try different USB ports. Even tried different PCs. Same thing.
slickie said:
When I try updating either the radio or MAGLDR in the install instructions there is this step2 where I have to establish an activesynch with my phone. I can't. So when I run the update it starts but progress stays at 0% both on PC and phone screen. After a few minutes I get error 262.
I'm trying to install radio 2.15 from Jayce Ooi's Paradise
Click to expand...
Click to collapse
find another radio from XDA for HTC HD2, "radio 2.15? What this mean? from Jyce Ooi's Paradise" do not mean anything, I know Jayce and he is an amateur, not master.
You don't answer on questions given to you, if you want help, do you flash from bootloader? turn-off phone, keep pressing volume-down, press button on?
In bootloader, when you connect to pc, show up USB on the bottom of the screen?
eclyptos said:
find another radio from XDA for HTC HD2, "radio 2.15? What this mean? from Jyce Ooi's Paradise" do not mean anything, I know Jayce and he is an amateur, not master.
You don't answer on questions given to you, if you want help, do you flash from bootloader? turn-off phone, keep pressing volume-down, press button on?
In bootloader, when you connect to pc, show up USB on the bottom of the screen?
Click to expand...
Click to collapse
The same thing happens even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship). What question haven't I answered? Yes, I flash from bootloader and yes USB shows up on the bottom when I connect it to the PC. When the updating of the ROM image starts there is no progress - neither on the instalator, nor on my phone (it shows HTC and a progress bar with 0%). After a couple of minutes I get Error 262 and "The ROM update utility has encountered a communication errors during update process."
Is my phone bricked?
slickie said:
The same thing happens even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship). What question haven't I answered? Yes, I flash from bootloader and yes USB shows up on the bottom when I connect it to the PC. When the updating of the ROM image starts there is no progress - neither on the instalator, nor on my phone (it shows HTC and a progress bar with 0%). After a couple of minutes I get Error 262 and "The ROM update utility has encountered a communication errors during update process."
Is my phone bricked?
Click to expand...
Click to collapse
Bricked mean dead, no life at all, your still alive but there is some errors, you should be happy to turn-on the phone in bootloader and usb be recognized. You have to try flash ONLY Radio 2.15.50.14.
If you can't flash the radio which I told you try to erase your rom with this tool.
you can update you magldr 1.11 to 1.13
you can update you magldr 1.11 to 1.13:highfive:
even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_S igned_15.32.50.07U_2.07.51.22_2_Ship
Click to expand...
Click to collapse
thats not a radio, thats a rom that includes a radio, but also includes an spl, , 1.66.0000
Are you SURE it still says x.xx.HSPL in bootloader? because hanging at 0% is very often associated with not having hspl installed.
samsamuel said:
thats not a radio, thats a rom that includes a radio, but also includes an spl, , 1.66.0000
Are you SURE it still says x.xx.HSPL in bootloader? because hanging at 0% is very often associated with not having hspl installed.
Click to expand...
Click to collapse
exactly, I forgot about that!
Also if you really have x.xx HSPL is no more a problem of you Phone but of you PC, so try different OS, even XP, and still trying. IS NOT THE PHONE.