Database Users

[Solved] Task 29 bricked my phone! Help!

Hey guys,
Well i had 2.08hspl on my phone with a 2.10._50 radio (something like that) and i ran task 29 to clean up my phone for a chunky rom.
After i ran the task29 utility, everything went to 100%, but i missed hittin the volume key in time. So i took out my battery and put it back in. Now i cant get the device to power up whatsoever.
Am i screwed?

Hi Jhonka
Can you get into bootloader mode? I have doen Task29 many times, and no issues, even if i miss the volume key. Try pressing the volume key down and hitting the power button for a moment before letting it go. Should get you into bootloader, and usb mode once you connect to the PC thru USB.

no i can't even get into the bootloader

may be not enough battery power
JhonKa said:
no i can't even get into the bootloader
Click to expand...
Click to collapse
your problem might be "not enough battery power"
charge your phone for a while and press power button by while pressing volume down.
hope it works.
good luck!

JhonKa said:
no i can't even get into the bootloader
Click to expand...
Click to collapse
what is the specific type/model of your phone?
battery might be low as mentioned by another user above.

take out the battery and press volume down and power-on to get into bootloader. connect yr device via usb and flash the ROM.
are u sure yr battery is not empty?

on the second thought, maybe the task29 was run without radio ROM?

sounds like it was run using a ..51.. radio on a tmous.

samsamuel said:
sounds like it was run using a ..51.. radio on a tmous.
Click to expand...
Click to collapse
so is it beyond help? wow, bummer
about naming convention, does TMOUS-compatible, TMOUS-support ROMs mean it's a TMOUS ROM?

BumAround said:
so is it beyond help? wow, bummer
about naming convention, does TMOUS-compatible, TMOUS-support ROMs mean it's a TMOUS ROM?
Click to expand...
Click to collapse
yes if it says tmous ok or tmous compatible or whatever then it means that that rom is based on version 2.x official tmous rom so it will work on tmous.
as for the op, if he did use a ..51.. radio then yes its unrecoverable.
but there are one or two posts with black screen, phone not booting, that aren't caused by this, but not many.
@op try the battery out for an hour and then try again.

thanks for all the responses guys.
I finally got it to work, i took the battery out for 30 minutes and held down the power button. (which i hear drains the rest of the charge in the phone)
turned it on, freaked out with joy then installed my new rom.

JhonKa said:
thanks for all the responses guys.
I finally got it to work, i took the battery out for 30 minutes and held down the power button. (which i hear drains the rest of the charge in the phone)
turned it on, freaked out with joy then installed my new rom.
Click to expand...
Click to collapse
dude I feel happy for you

JhonKa said:
thanks for all the responses guys.
I finally got it to work, i took the battery out for 30 minutes and held down the power button. (which i hear drains the rest of the charge in the phone)
turned it on, freaked out with joy then installed my new rom.
Click to expand...
Click to collapse
wow, good thing it worked.
btw you never told us which version of the phone that you're having? (US/non-US/unlocked/etc)

HD2 not booting
I have the same problem but I can get back to bootloader mode.. Problem is at the beginning when I ran task29, I don't think I flashed with the radio so now my phone is not booting. How am I going to put back the radio. Please help!!!

can you go to the bootloader/
dau888 said:
I have the same problem but I can get back to bootloader mode.. Problem is at the beginning when I ran task29, I don't think I flashed with the radio so now my phone is not booting. How am I going to put back the radio. Please help!!!
Click to expand...
Click to collapse
if you can go to the bootloader,then put the radio into your sd card and change the name accordingly.
then flash from boot loader.
am i right?

thihaz said:
if you can go to the bootloader,then put the radio into your sd card and change the name accordingly.
then flash from boot loader.
am i right?
Click to expand...
Click to collapse
Hi
Recommmended way of flashing is for the HD2 is from your pc not from microsd. Put the device in the bootloader and connect the usb and flash the radio or rom from the pc. This is the way is more safe.
Good luck

[Q] Bricked phone after task29 and rom flashing

Hello. First I want to thank all of you who develop roms and the like. I have had such a blast over the past month and a half customizing my phone in ways I never thought possible. Last night I ran flashaholicruu.exe on my HTC HD2 Leo. The task29 seemed to work properly, however when I attempted to flash the rom I received errors. I tried Leo_Radio_2.11.50.26.sfx, which had previously worked on my phone. It stopped at 96%. I did the recovery, however the phone now will not even boot the splash screen. It simply vibrates non-stop when I turn it on until I remove the battery. Does anyone have ANY advice at all? Am I able to load a ROM onto the SD card and directly boot from it while my phone is in this state?
I have removed the battery and reinserted it. Did not work.
I have also tried pressing the volume buttons and the power on button to get the bootloader, but just vibrates in the same manner as when I press on button.
Please help!
Thank you

happend to me with a friends phone...i jus replaced it under insurance

Nismo300zx said:
happend to me with a friends phone...i jus replaced it under insurance
Click to expand...
Click to collapse
Ahh. I wish. T-Mobile is giving me a hard time about replacing it because I was not the original owner of the phone. The phone is only about 3-4 months old though.

I had this happen to me.
Try to load it directly into bootloader by holding vol-down when you press power button, then flash another radio (i recommend 2.12.5) then try another ROM thru RUU.
Also, make sure your battery is place in there securely and that all 3 pins from the phone are sticking out.
I had a situation where one of the pins was sticking vertically and the battery was only hitting 2 (from doing too many battery pulls) and it did this weird vibrate splash screen boot sequence.

electrokitten said:
Ahh. I wish. T-Mobile is giving me a hard time about replacing it because I was not the original owner of the phone. The phone is only about 3-4 months old though.
Click to expand...
Click to collapse
You'll need contact details for the original owner, but by law they have to honor the agreement they put in place with them, regardless of whether you are that person or not.
Just get back onto T-Mobile and if they say no then speak to someone higher up. I know this to be the case after selling a palm pre to someone at the beginning of the year and it died on him shortly after.

johncmolyneux said:
You'll need contact details for the original owner, but by law they have to honor the agreement they put in place with them, regardless of whether you are that person or not.
Just get back onto T-Mobile and if they say no then speak to someone higher up. I know this to be the case after selling a palm pre to someone at the beginning of the year and it died on him shortly after.
Click to expand...
Click to collapse
Really? This is good to know. I contacted the original owner. I feel so bad and I hope he doesn't think I am trying to scam him. I just want a working phone and I think that T-Mobile should honor that.

orangekid said:
I had this happen to me.
Try to load it directly into bootloader by holding vol-down when you press power button, then flash another radio (i recommend 2.12.5) then try another ROM thru RUU.
Click to expand...
Click to collapse
I think the bootloader may be gone. Does the task29 remove this? I can't get even to the bootloader using the method above (I have tried many times).
orangekid said:
Also, make sure your battery is place in there securely and that all 3 pins from the phone are sticking out.
I had a situation where one of the pins was sticking vertically and the battery was only hitting 2 (from doing too many battery pulls) and it did this weird vibrate splash screen boot sequence.
Click to expand...
Click to collapse
Good to know, I will try this. I do have some bent pins.

No task 29 doesn't remove the bootloader, I always use it before flashing a new ROM...
Sent from my HTC HD2 using XDA App

copy the nbh file from the stock rom to the sd card..that usually fix it..

gabbs said:
copy the nbh file from the stock rom to the sd card..that usually fix it..
Click to expand...
Click to collapse
Good advice... Now if only he could access the bootloader he'd be sorted

gabbs said:
copy the nbh file from the stock rom to the sd card..that usually fix it..
Click to expand...
Click to collapse
Major_Sarcasm said:
Good advice... Now if only he could access the bootloader he'd be sorted
Click to expand...
Click to collapse
he needs to rename the .nbh file to LEOIMG.nbh and pair it with the RUU that came
with that same stock ROM
but then again, if he cant get into bootloader, the phone is definitely bricked

electrokitten said:
Hello. First I want to thank all of you who develop roms and the like. I have had such a blast over the past month and a half customizing my phone in ways I never thought possible. Last night I ran flashaholicruu.exe on my HTC HD2 Leo. The task29 seemed to work properly, however when I attempted to flash the rom I received errors. I tried Leo_Radio_2.11.50.26.sfx, which had previously worked on my phone. It stopped at 96%. I did the recovery, however the phone now will not even boot the splash screen. It simply vibrates non-stop when I turn it on until I remove the battery. Does anyone have ANY advice at all? Am I able to load a ROM onto the SD card and directly boot from it while my phone is in this state?
I have removed the battery and reinserted it. Did not work.
I have also tried pressing the volume buttons and the power on button to get the bootloader, but just vibrates in the same manner as when I press on button.
Please help!
Thank you
Click to expand...
Click to collapse
What exactly did you do to try and enter bootloader mode? You said you pressed the volume 'buttons' and the power button but that combination would initiate a Hard Reset and not bootloader mode..
How to get into your Bootloader
1. Turn your phone off
2. Press and hold the VOLUME DOWN then Press and hold the POWER button. After about 3 seconds the tri-coloured screen should appear.
3. To exit Bootloader you need to remove your back cover and pull the battery out for a few seconds, then replace it and press the power button to reboot your phone.
If you cannot get into the bootloader with the above instructions then it looks like you have bricked your device somehow but im not sure exactly how you could do it as task29 doesnt touch HardSPL.
If you can get into bootloader then you can flash a rom back to your device using the sd card method in my guide *HERE*.
Mark.

[Q] Crashed HD2, destroyed?

after flashing to 14 jan mdj. my hd2 crashed after 1 day of use. After that I can't boot into android or use USB. I think I even can't charge the phone. I don't see the red led. Andy ideas for fixing it? Try a new battery? It doesn't start up anymore, but it did a few times and said 12.fatal hit when booting android. I haven't tried Tricolour because I can't start it up anymore
Thanks,

When you turn on your phone what happens? What screen dow it take you to? What does it say when trying to run android? .......and for future notice this is the comnplete wrong section for this....and some more info regarding device, hspl, radio would be helpful too.

oh word? ... try this
1..first download the official wm 6.5 rom from tmobile or http://www.htchd2forum.com/general-...SID=799c9ce6abe4e3ddc05368f8432db509#msg22469
2...second remove the SD card and connect the phone to ur computer
3...hold the down volume + power buttom till u see 4 colurs and them run the tmobile official rom... let me know what happens

it doesn't boot up anymore, I will post again when I have it booting again.

All have to do is to download an htc official rom and connect ur Htc hd2 to
computer and flash it
Good luck
Sent from my HTC HD2 using XDA App

phaverkamp said:
it doesn't boot up anymore, I will post again when I have it booting again.
Click to expand...
Click to collapse
connect the phone to ur computer
hold the down volume + power button till u see 4 colors and them run the tmobile official rom... let me know what happens

In the name of the wee man.
Post this in the right bloomin' topic.
The Mods have just spent an age reorganising this whole corner of XDA and what do you do?
Bugger it all up.
Well done.
At least you are consistent, you buggered your phone and the forum. Bravo.

phaverkamp said:
it doesn't boot up anymore, I will post again when I have it booting again.
Click to expand...
Click to collapse
Can you seriously follow anyone's instructions given man? Quit trying to boot the phone. Connect the phone with your PC via the USB cable. Hold down the "volume down" key and the "power" key at the same time. Tell us if you see the tri colored screen.

phaverkamp said:
after flashing to 14 jan mdj. my hd2 crashed after 1 day of use. After that I can't boot into android or use USB. I think I even can't charge the phone. I don't see the red led. Andy ideas for fixing it? Try a new battery? It doesn't start up anymore, but it did a few times and said 12.fatal hit when booting android. I haven't tried Tricolour because I can't start it up anymore
Thanks,
Click to expand...
Click to collapse
Have you checked the battery contacts? They bend very easy, and the symptoms you describe are exactly those of that. If they are bent, VERY, OH SO VERY CAREFULLY straighten them up. If one or more are broken, I hate to tell you this, but you need to buy a new phone.

phaverkamp said:
after flashing to 14 jan mdj. my hd2 crashed after 1 day of use. After that I can't boot into android or use USB. I think I even can't charge the phone. I don't see the red led. Andy ideas for fixing it? Try a new battery? It doesn't start up anymore, but it did a few times and said 12.fatal hit when booting android. I haven't tried Tricolour because I can't start it up anymore
Thanks,
Click to expand...
Click to collapse
I think you have wrongly done the Clock Work Mod which shows the 123Fatal Hit error and ur hd2 remains stuck there. Your HD2 is not crashed at all just charge it with an external charger then go to bootloader by pressing n holding Volume Down key and Power button until you the triple coloured screen, then connect your data cable to HD2 and flash it with a stock windows mobile rom so it will restore ur hd2 and after that u can install nand rom on it by following each and every step mentioned in tutorials here. Whenever I select boot AD SD after flashing partition layout I always get 123Fatal error now I don't understand what the problem is....If someone has a solution for this problem please reply in this thread as I don't want flashing through DFT method.

[Q] Hellllllllllllllllllllllllllllllllllllllllllllllll lllp

I was trying to install blackSTONEhengeHyPerSlim_4_1 on my blackstone. I installed olinex and after that stored the nbh and exe file on the sd card and then through task 29 flashed it. The rom got successfully installed but now the phone is stuck at the bootup. It says
Checking Radio...
Checking protocol..
Checking Rom..
But now won't get to the next screen.Because of this i can't get to active sync. Please help..Pleaaaasseee

Did u follow the instructions completely, cause it worked fine for me and others... Do you have radio 1.14 or above installed? Did u try to reflash?

ok, no need to worry. Boot into bootloader. What is your SPL?

Yes i did follow the instructions. Now the phone won't bootup. I tried it with the volume down and power up method. Rom does get installed but then again it won't bootup..

Did you try Vol UP + Vol Down + Power ?

Yes i did try that after my phone got screwed up with test29 method but it shows nothing at all after successfully installing rom..:-s

no need to worry
always read read read and must read before flashing. I think your phone is quite ok. You does task29 to it. what is task 29 means. it means task29 will clean our device completely only splash screen displyaed, phone always stucked on this screen. it is very normal, it means you completyely cleaned your device. now you are ready to flash your device. do the following procedure--
1. remove the battery and reinsert it.
2. now turn on the phone while pushing volume down key.
then bootloader (tricolor screen) mode will be displayed. many times it will not come into bootloader and device normally starts and stuck on splash screen. the reason is simple, you didnt press volume down key properly, it happend many times to me also.
Now remove battery cover, remove battery and reinsert it, dont cover the battery, now take slylus & press volume down strip with the stylus. ( volume up & down keys are installed in battery cover, so when you push volume down key in flap open condition, it should be done by stylus.)
ok
push volume down by stylus & hold it and start the device, it will come in tricolor screen means bootloader mode, on the bottom screen it will show serial.
Now conect the device to the pc & bottom line on the screen will become serial to USB.
Now perform task28= means flash normal rom, do not perform task 29 again.
task29 will take 1 minute to flash while normal RUU will take about 7-8 minute.
try it and give feedback/

kulwant said:
Yes i did follow the instructions. Now the phone won't bootup. I tried it with the volume down and power up method. Rom does get installed but then again it won't bootup..
Click to expand...
Click to collapse
Have you flashsed a differnet radio ?

What you did is just Task29 your phone. Task29 needs something to flash in order to do its thing. Usually we flash radios (good ones obviously) because they are smaller than full roms. If you flash a full rom with Flash29, it will get erased after completion.
What you need to do now (since your phone now has no ROM installed) is boot it while pressing volume down to get to the bootloader, plug via USB and flash a rom using a "non-task29" flasher, like the standard BlackStoneCustomRUU.exe file that comes with basically every rom.

Hello thanks for replying my internet wasn't working but i did manage to boot my phone but now the touch stops working after. I know this as i press the volume button and the phone responds to that hence telling me it's not really freezed up. This is all what i did.
Stored .nbh file in the task 29 folder this is the rom version whose nbh file is used (RUU_Duttys_HD_V3.9__XT_Turbo_5.2.21051.1.6.4_1.59.709.0_Radio_52.62.25.34_1.14.25.24_)
After the flashing is done i reset the phone by taking out battery and starting it again in bootloader.
Now i flashed again with (blackSTONEhengeHyPerSlim_4_1)
After installing it completely the touch stops responding.
Kindly help me with what seems to be the problem. Thanks

kulwant said:
Hello thanks for replying my internet wasn't working but i did manage to boot my phone but now the touch stops working after. I know this as i press the volume button and the phone responds to that hence telling me it's not really freezed up. This is all what i did.
Stored .nbh file in the task 29 folder this is the rom version whose nbh file is used (RUU_Duttys_HD_V3.9__XT_Turbo_5.2.21051.1.6.4_1.59.709.0_Radio_52.62.25.34_1.14.25.24_)
After the flashing is done i reset the phone by taking out battery and starting it again in bootloader.
Now i flashed again with (blackSTONEhengeHyPerSlim_4_1)
After installing it completely the touch stops responding.
Kindly help me with what seems to be the problem. Thanks
Click to expand...
Click to collapse
Hi mate.
I did somthing for you....so i hope it will helps you.
1. download file from this link. http://hotfile.com/dl/115059516/5623431/Radio_1.13.xx(original_hd_nbh)__task29.rar.html and after unrar.
2. Make task 29 with this one. (Nothing change in that unrar folder)
3. After finished T29, take uot battery, put it back, put device to BootLoad. screen.
4. Connect with PC again and flash your desided ROM. (it means if you choice your rom, after unrar or unzip, Rom has own folder with that all files ...BLACIMG.nbh, BS_CustomRUU.exe, etc......

thanks i'll just download and do it..Will definitely post in what happened...Thanks a tonne for the quick response..

kulwant said:
thanks i'll just download and do it..Will definitely post in what happened...Thanks a tonne for the quick response..
Click to expand...
Click to collapse
...It's ok mate, like i wrote, i hohe, it 'll helps you.
let me know after....

Any new good looking rom you would suggest for me to try that would be bugfree ???

kulwant said:
Any new good looking rom you would suggest for me to try that would be bugfree ???
Click to expand...
Click to collapse
.... for beginning: T29 finished ok?
for your guestion: Hmmmm, for me...really good ROM is from Cloudyfa, but objectively, it's up to you, which one from this site you choice.

The link you gave me says
This file is either removed due to copyright claim or is deleted by the uploader.
:-s

kulwant said:
The link you gave me says
This file is either removed due to copyright claim or is deleted by the uploader.
:-s
Click to expand...
Click to collapse
Yeas mate, i deleted it. I was thinking, that you download this file already and saved it to your PC.

LoL it's all cool it takes a while i got 512kbps..I got the stock rom from xda page
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
This one's fine right

kulwant said:
LoL it's all cool it takes a while i got 512kbps..I got the stock rom from xda page
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
This one's fine right
Click to expand...
Click to collapse
Yes that one is fine. Once T29 is complete take out battery and then re-insert it. Now put phone into bootloader (hold vol down and press power on while still holding vol down. BOOTLOADER IS A TRI-COLOUR SCREEN).
Now flash your rom

i also flashed blackstonhenge hyperslim 4.6 and now touchscreen stopped working....any solution...

[Q] Can't get to Bootloader

Hey Guys. I was hoping someone could help me with my problem.
Currently my HTC HD2 is running cyanogenmod7 using MAGLDR 1.13.
I want to switch back to winmo 6.5 to start fresh and have read tutorials that i need to enter bootloader ( the red, white, green screen thingy) to establish a connection with activesync. But the problem is that i can't actually get into bootloader and i have tried volume down button with the power button combo and it doesn't seem to work.
If someone knows how to get to bootloader then please help.

While the phone is off... do what you did... hold power and volume down buttons...

Yes, i tried that 20 times and it doesn't work

Roger9546 said:
Yes, i tried that 20 times and it doesn't work
Click to expand...
Click to collapse
Does the volume down button work on your HD2? Sounds like it does not.

That's the strange part. My volume buttons work perfectly in Android and Magldr. I don't know what's happening

switch off the phone and open it again while you are holding the end call button
you will go the magladr menu , i thik you can find something there to take to the bootloader

the_entity said:
switch off the phone and open it again while you are holding the end call button
you will go the magladr menu , i thik you can find something there to take to the bootloader
Click to expand...
Click to collapse
No no no no no and NO!!!!!!!!!!!!
There is nothing in MAGLDR that can make your HD2 go into bootloader. The only this.g that can get you into the bootloader besides the external hardware buttons is the bootloader.exe that can be run from inside Windows Mobile. It can only be run from inside Windows Mobile. MAGLDR is a custom bootloader that runs after the HSPL bootloader and has no way of communicating with the HSPL bootloader.
At the OP, you may have a faulty volume button ribbon that is causing you not to be able to boot into the bootloader. Check out this thread you will see what I mean. Read post #10

Boot loader mode
Bootloader mode is handy for checking the HD2's version of Hard SPL as well as the installed ROM and Radio versions,and also for ROM or Radio flashing to the HD2. I sometimes use the Bootloader method to flash ROMs as it saves connecting to Activesync/WMDC because the PC recognises the HD2 as connected via USB. It is also useful for flashing a ROM or Radio version if the battery charge is less than 50%, as it ignores the 50% charge warning that is normally displayed when flashing if the HD2 is low on charge. Never use this method if you have less than a 30% charge as you will be in deep trouble if the HD2 runs out of power while flashing a ROM or Radio version!
To place the HD2 into Bootloader mode, remove the HD2's back cover hold down the volume down key, now press in the red reset button under the back cover to the bottom left of the SIM, release the soft reset button but continue to hold the volume down key in until you are presented with the tri colour bootloader screen. To exit Soft Reset the device.

AlexALP said:
Bootloader mode is handy for checking the HD2's version of Hard SPL as well as the installed ROM and Radio versions,and also for ROM or Radio flashing to the HD2. I sometimes use the Bootloader method to flash ROMs as it saves connecting to Activesync/WMDC because the PC recognises the HD2 as connected via USB. It is also useful for flashing a ROM or Radio version if the battery charge is less than 50%, as it ignores the 50% charge warning that is normally displayed when flashing if the HD2 is low on charge. Never use this method if you have less than a 30% charge as you will be in deep trouble if the HD2 runs out of power while flashing a ROM or Radio version!
To place the HD2 into Bootloader mode, remove the HD2's back cover hold down the volume down key, now press in the red reset button under the back cover to the bottom left of the SIM, release the soft reset button but continue to hold the volume down key in until you are presented with the tri colour bootloader screen. To exit Soft Reset the device.
Click to expand...
Click to collapse
Hi!
I try this so many time, but my hd2 does not step in bootloader. Have you got some other idea??

I have exactly the same problem, help!

Roger9546 said:
That's the strange part. My volume buttons work perfectly in Android and Magldr. I don't know what's happening
Click to expand...
Click to collapse
Can you get into the windows start- settings - system? If yes, there is an app that says "clear storage memory", which brings you back to the factory settings when you bought it. It's worth a try.
Entering bootloader screen is sometimes difficult: press and hold the volume down button and then press shortly
the power button, this should bring you to this screen. If it does not, remove your battery for at least 10 minutes and try again.
Good luck and regards, Kuzibri

I had the same problem ...
I could not enter the bootmanager in android brief button press to end a call, we moved the menu to shut down, reset, etc, the same menu that appears when you hold down the button longer to stop calling ...
This defect appeared to me after I lay HD2 due to large changes in ambient temperature ...
After a few days of research, opening, drying I removed the defect, so I pulled out and cleaned the keys below the screen (Home, Menu, Back, red and green) and wipe the foil that these pressures are the same buttons ...
My HD2 has been working for 2 weeks with no errors

same here but ...
to get in to bootloader i just discovered a different (strange)way ... from winmo , with back cover off press red reset button and imediately while reseting press volume down ... this is my only way to get in to ... otherwise , all the keys are fully working when in windows mobile .

very strange
all the keys includind the volume down key, works well inside windows, but I just cant go to bootloader.
I will dismante the phone, wash it and dry it, to see if something changes,

I have problem getting into 3 color bootloader also, but its because my voulme down is broken/ doesn't work anymore. Any other ways besides the volume down button?

Jcamacho228 said:
I have problem getting into 3 color bootloader also, but its because my voulme down is broken/ doesn't work anymore. Any other ways besides the volume down button?
Click to expand...
Click to collapse
only if you are currently running winmo 6.5, , theres a winmo app to restart into bootloader.
alternatively, dismantle the phone and short the voldown connections.

bootloader&spl
How to enter bootloader(tricolor scren) on hd2 t-mobile-usa, i tried wth vol down key but no respns. I thk may be another key for hd2 t-mobile-usa. Does any one know? Or thr is no Spl with ths stock rom...if so, how to instal Spl on hd2 t-mobile(1024) or stock rom wth Spl so that i can instal Hspl... Thanx

foysyl said:
How to enter bootloader(tricolor scren) on hd2 t-mobile-usa, i tried wth vol down key but no respns. I thk may be another key for hd2 t-mobile-usa. Does any one know? Or thr is no Spl with ths stock rom...if so,
Click to expand...
Click to collapse
phone off
press and hold voldown
tap and release power
keep holding voldown.
No, the tmous doesn't use a different method than the regular hd2.
how to instal Spl on hd2 t-mobile(1024) or stock rom wth Spl so that i can instal Hspl... Thanx
Click to expand...
Click to collapse
all stock roms include an spl, i think YOU mean ''or stock rom with hspl.''', , no, there are no stock roms that include hspl.
there is only one way to apply HSPL, , and that's through bootloader.

bootloader prob. on hd2 usa
How to enter bootloader(tricolor scren) on hd2 t-mobile-usa, i tried wth vol down key but no respns. I thk may be another key for hd2 t-mobile-usa. Does any one know? Or thr is no Spl with ths stock rom¡*if so, how to instal Spl on hd2 t-mobile(1024) or stock rom wth Spl so that i can instal Hspl¡* & whr i can get bootloader.exe for hd2 - wp6.5
Thanx
---------- Post added at 05:54 PM ---------- Previous post was at 05:30 PM ----------
But cant get its bootloader by holding vol down key wth power key at a time thn pres reset butn.
Is thr any soft/bootloader.exe for entering hd2's bootloader through pc or frm phn(hd2-usa)? If so thn pls giv the link. Or is needed to re-instll stock rom over prsnt stock rom
Thnx([email protected])
---------- Post added at 06:12 PM ---------- Previous post was at 05:54 PM ----------
samsamuel said:
only if you are currently running winmo 6.5, , theres a winmo app to restart into bootloader.
alternatively, dismantle the phone and short the voldown connections.
Click to expand...
Click to collapse
Need ths App...pls giv me the download link

Try this!
Hi, I had a similar problem where I could not enter the boot loader. The solution I found that worked for me was provided by: broncogr on another thread discussing a similar issue with the DHD ( http://forum.xda-developers.com/showthread.php?t=889567 )
"restart the phone
when the capacitive buttons light is off immediately press and hold volume - button and keep holding until device is in bootloader
cheers " - broncogr
Hope this helps someone.
Ez