Related
Hi there
I tried a lot of stuff from different topics,but still after selecting the voice in the wizard,Tomtom simply exits ??
Thanks
Fefe
Try this... extract to 'My Documents' so that the entire TomTom folder with the currentmap.dat in it is in My Documents on the exec and that's pretty much it...
Good Luck!
is this a legitimate copy of TomTom Navigator 5.? Is yes, then I don't know, but I have seen the symptoms you describe occur on a cracked version of TomTom.
Create directory 'My documents\Tomtom'
i had a scout around about this, and found a nfo that said for that "special" version you need to run through the wizard before swapping the exe for the "special" exe, then when you get to the regging, do manual then cancel,
then swap to the "special" exe and all will work fine,
i take it you know what "special" is!!!! and im not sure if this actually works, i dont really need gps on my phone with a carputer in the car.
I have tried both on my Sprint Mogul with dcd 3.26 and neither are working right. Both freeze up at the menu screen, whether simple or advanced, the next screen it locks.
I have 23.7M (or so) of free RAM after a soft reset. I've let it sit on that menu for 5 minutes straight, wondering if it were catching up. No good.
I have TomTom7, but I want something with text to speech support.
The first time you run Igo or Oncourse it goes thru your contact list and checks the address on all of them. If you have a very large contact list it could be causing it to act very slow. It only does this once, so after it finishes it won't do it again in the future.
You might also check your config file, I think it's called sys.txt, would have to search to verify, but it lists your com ports. If you have an invalid com port for your GPS it can lock up entirely. Find this file and change it to com 4 baud 4800 and then restart it, should work fine then.
Let me know if that doesn't work. I've started Igo with as little as 8mb free, it ran, tho not very well and crashed shortly afterwards, but with 23mb it should run very well. So I don't think it's a memory issue in your case.
BTC
groovy. I'll sys.txt it up and report back.
getting there.... trying different combinations of ... packages ... see what works and what doesnt.
Can you mix OnCourse with iGo?
As far as I know, OnCourse is just a licensed OEM of of Igo, I've heard that the maps, skins, themes, etc all work fine with both.
I personally haven't tried OnCourse because the word I heard was that it's a compressed .exe file which in turns requires more ram to uncompress and then run. There were several looking into uncompressing the exe file and running directly, but have not seen any confirmed threads that someone has it resolved.
BTC
yeah, im avoiding an actual install of oncourse... however, what I have, has some things in it that my igo doesnt have, as well as US poi's which my igo doesnt have. More experimenting tonight.
I too was having an issue with IGO8 not starting properly, I could enter the program but none of the icons would function.....well not really.....I would click settings and about 30 seconds later I would hear the click sound but IGO would stay at that screen and then about 1 minute later it would goto the settings screen.
After doing some research I did find that it was an issue that IGO had with
adding my contacts addresses(I'm guessing that this is a ram issue). Here is what I added to the sys.txt file to stop IGO from trying to add my contacts to its POI DB, disable_outlookpoi=1 needs to be added under [debug]. I'm pretty sure I found a sys.txt config on ppcgeeks in the vouge section.
I cannot get the TTS to work as it appears that our Titans don't have enough ram to allow all of the features of IGO to work.
I have installed DCD latest with a couple of programs installed i.e. MSVC, Oxios, DCD carrier cab(great work DCD, every rom he makes just keeps getting faster and allowing more ram to be utilized) at boot I have about 23-24mb available, when starting IGO and then minimizing IGO I have 1.3-1.4MB free ram. When trying to select the Susan TTS voice it immediately crashes with an out of memory error. I'm also using the full maps of North America, all the building files and the terrain file for USA as well. When I get a chance I'm going to try only my state and my states buildings and see if that frees up any additional ram for TTS.
Good luck
i have noticed that it wont run unless I prime the GPS, even with the [gps] code in the sys.txt
Scrufdog said:
i have noticed that it wont run unless I prime the GPS, even with the [gps] code in the sys.txt
Click to expand...
Click to collapse
I have found the same thing, I've attached a .zip file that someone created that will give you a shortcut for astroGPS to prime the GPS and also start IGO8. You must have astroGPS installed but it works like a treat.
anyone figure out how to setup tts with any tweaks or removing some default programs for more ram? I installed dcd latest rom with nothing else but igo8 and still get that out of memory :/ Also i have igo running with no terrain and in 2d mode with no luck
So is anyone able to get Text to Speech (TTS) works on Titan?
Hi all,
For everyone with the problem with TomTom Navigator whereby it only announces part of the directions, attached is a small application which provides a workaround.
It works by playing a short silent WAV file in a loop in the background, starting TomTom then shutting itself down automatically once TomTom is closed. This is basically the same mechanism as mentioned on another thread whereby a silent MP3 is played through a script in an external MP3 player but written as a self-contained program.
To run TomTom with the fix:
If you don't already have it, first install the Microsoft .NET 3.5 Compact Framework. Available as a cab here: http://www.megaupload.com/?d=2ZGV1DNJ.
Unzip the attached TomTom Audio Fix.zip and copy TomTom Audio Fix.exe into your TomTom Navigator directory e.g. "\Program Files\Navigator". You can then just run TomTom Audio Fix.exe which will automatically start TomTom.
This has been tested on TT 7.910 (9185) and 7.915 (9196), please post here if you try it out with whether it's working ok or you run into any problems!
Updates
v1.10:
- Icon refreshed, now displaying correctly.
- When run, TomTom Audio Fix.exe will now automatically generate a "TomTom Navigator.lnk" shortcut in the current directory. This can be copied directly over the installed TomTom shortcut in the start menu; saving the need to manually create a shortcut to the fix.
v1.11:
- Thanks to Mr_Q, this is now provided as a .cab file:
º Automatically copies file to TomTom Navigator directory and overwrites the shortcut in the start menu.
º Install the cab in the same location as you installed TomTom (eg. Storage Card), else it won't work.- Removed redundant change from 1.10 which created the TomTom Navigator shortcut.
Regards,
JDH
Brilliant. Thanks very much to you and those who figured out what the workaround was. Just goes to show what a marvellous place this Internet can be!
Filbert
Good work! Thanx a lot! I'll try it immediately.
Works really good on TT 7.915.9196
Thanx again.
What´s .NET 3.5 Compact Framework?
@JohnnyDH
Do I understand it right, after installing the fix I have to start the fix from explorer and TT will start automatically??
In that case is there a chance for a shortcut in programm directory? That would make it more easy than starting the programm everytime from explorer.
Thanks for the answer.
Rodgauman
Beside my question one post before, the fix worked fine. Only a shortcut would be fine.
I tried to copied the fix into windows\startmenue folder, but then the correct path will not be found.
I have navigator on my storage card installed. Path is in german:
Mein Gerät\Speicherkarte\Programme\Navigator
When I start the fix from there it works fine.
Thanks a lot JohnnyDH! This really does work great. Can I make a request? Would it be possible to change the icon of the file as it is of pretty bad quality now. I'd appreciate it very much.
@rodgauman
You will need to manually edit the TomTom shortcut in your windows\startmenue folder. Copy the TomTom Navigator.lnk file from the start menu to your PC, open it with a text editor, and change where it says "TomTom Navigator.exe" to "TomTom Audio Fix.exe" e.g. I changed mine from:
47#"\Program Files\Navigator\TomTom Navigator.exe"
to:
47#"\Program Files\Navigator\TomTom Audio Fix.exe"
Save the changes and copy it back replacing the original file. Unfortunately there are too many installation locations / languages etc for me to automate this!
@daffie
Not a problem, glad it is working for you! Good spot on the icon, it was extracted directly from TomTom Navigator.exe and I hadn't noticed. I will upload an updated version at some point in the next couple of days to give a few more people a chance to test it in case any fixes are required.
thank you man.
it worked for me too...tomtom 7.915.9196
@JohnnyDH
Thanks again, editing of shortcut worked fine!
Beside that I learned how to create a shortcut for other programms.
Great Job!
Thanks JohnnyDH
Work fine version 7.915.
JohnnyDH said:
@rodgauman
@daffie
Not a problem, glad it is working for you! Good spot on the icon, it was extracted directly from TomTom Navigator.exe and I hadn't noticed. I will upload an updated version at some point in the next couple of days to give a few more people a chance to test it in case any fixes are required.
Click to expand...
Click to collapse
Thanks a lot, I really appreciate it! Today I did a testrun using TT7 and the voice now works like a charm...very happy about this fix!
Its working like a charm. Theres only one thing I noticed. When TomTom is started, it starts muted. Is this how its supposed to be?
have been waiting so anxiously for a TT voice patch! Many many thanks!!!
ps creating a high resolution icon would be nice, since it looks so ugly on new HTC program menu
Thanks a lot....this bug has been driving me crazy...works on TomTom7.450
Thank you JohnnyDH,
i use it with TTN7.915.9196 vga black. You save my Life
Awesome.
Thanks a lot man !
@ Johnny DH
thanke u very much ... i already fix it... Finayly...i really appreciated..
TomTom Audio Fix v1.10 works like a charm!
Kudoos to you
Thankyou! this worked perfectly
In order to have both TTS and Contact POI's working in iGO8 you're going to need two different versions of iGO8.
FIRST VERSION NEEDED: iGO8 v8.32.64029 (Nov 7 2008)
This version is designed for the PDA, and as such is able to geocode contact information. Install this version with the attached 64029sys.txt
At this point if everything is done correctly, iGO8 should boot normally BUT be VERY slow and unresponsive. This is GOOD! This is iGO8 Geocoding your contacts. Depending on the quantity of contacts with addresses you have, this could take a VERY long time. When it is done you will get a message similar to the following:
Geocoding finished with errors. 38 of 110 addresses found, 72 failed. Do you want to see the details?
At this point you could see the details of the errors, which will show you all of the addresses that are not entered into Outlook in a iGO8 palatable way. You could just ignore them and be happy with what you have (unlikely), or go back into Outlook, correct the formatting errors, and try again (and continue your suffering).
This can be VERY tedious... iGO is one picky bastard. You might even have to input the addresses into iGO as destinations, see how iGO formats the addresses, and then change the Outlook contacts to match the format iGO uses for a particular address.
I have even heard that contact need to be deleted and reentered into Outlook in the proper iGO8 fashion or you will continue to get errors for particular contacts.
SYNTAX ADVICE:
not Blvd. --> Blvd (The little "." will throw an error every time)
not Blvd --> Boulevard ("Usually" iGO dislikes abbreviations)
not N. --> N --> North (This is hit or miss)
NEVER use apt# (just give up and don't try)
NO Suite # (same as above)
If you have to have apt or suite #'s AND you want iGO to geocode, then the only way to get it both ways is to use the "OTHER" address in Outlook to place the iGO friendly address and the correct address in the "Business" or "Home" Outlook address. The ones with apt or suite # will error, but the second addresses in the "Other" address without the apt or suite # will geocode as POI's fine.
When you are done, you will be left with this little piece of GOLD... YOUR CONTACT POI's FILE ! ! !
\iGO8\save\gccache.dat
You'll want to back this file up somewhere else for safe keeping. We don't want all this hard work to go to waste.
SECOND VERSION NEEDED: iGO8_v8.3.4.102680 (Aug 13 2009)
This is the newest PNA version that does not have the ability to geopcode contact POI's, but it is able to read the gccache.dat file created by the PDA version above AND it is capable of TTS. Install this version with the attached 102680sys.txt
You will need to install this version and simply place the gccache.dat into the iGO/save folder and iGO will do the rest for you.
Now getting iGO8 to reliably run TTS is a different story. TTS requires ALOT of RAM to run. If there is not enough RAM available (~115-120mb), then it will simply refuse to play TTS voice prompts and you will be stuck with standard voice prompts. To free up a good chunk of the necessary RAM install both NOPushInternet_v2.cab and SSK TP2 Dynamic Resource Proxy.cab. To get the rest your available RAM to acceptable levels you will need to disable TF3D, run CleanRAM, and then start iGO.
Sounds complicated? Well, fortunately itsachirpthing over at PPCGeeks has created a nice little script that does just this. The original post can be found HERE. And the original thread can be found HERE. I recommend reading both these original threads. They have additional information to get iGO8 working properly on TP2.
itsachirpthing @ PPCGeeks said:
I have a custom mort script that will turn off TF3D, run CleanRam (I have custom process enabled to exit Opera and Tmail within CleanRam), then run Igo8. Once you are finished with Igo and you exit, TF3D will restart. This took some testing, but this works everytime with the high quality TTS voices. I have had no issues. I have posted the code below, this will work on your device providing that you install CleanRam to your "device" and your IGo program is listed as "\storage card\iGO8\igo8.exe". These HQ TTS voice issues baffled me for months, but now they work consistently without a soft reset.
Again this code will stop TF3D, Run CleanRam, Start Igo... then when you exit iGo it will restart TF3D.
manilastate=ProcExists("manila.exe")
If (manilastate)
Kill("biotouch.exe")
RegWriteDword ("HKLM","Software\Microsoft\Today\Items\TouchFLO 3D","Enabled",0)
RedrawToday
endif
RunWait("\program files\htcaddicts cleanram\htcaddicts_cleanram.exe")
RunWait("\storage card\iGO8\igo8.exe")
Sleep(5000)
Kill("Repllog.exe")
While ( ProcExists("igo8.exe") )
IdleTimerReset
Sleep(500)
EndWhile
If (manilastate)
RegWriteDword ("HKLM","Software\Microsoft\Today\Items\TouchFLO 3D","Enabled",1)
RedrawToday
Run("\windows\biotouch.exe")
endif
I have attached the script to run with mort script. I hope others can benfit as well. Good luck and enjoy!
Click to expand...
Click to collapse
I have added this iGO script to the MortScript.cab posted here. You need it and CleanRAM.cab. Install both to the device, not the SD Card. Then just click on the Plain iGO Scipt icon in the Start Menu. The script will close TF3D, run CleanRAm, start iGO8, and when iGO8 is exited, it will start TF3D again
Inaddition to the above Script, you will need to install both NOPushInternet_v2.cab AND SSK TP2 Dynamic Resource Proxy.cab
in order to free up enough RAM. But with the above script, CleanRAM, and these two cabs, you should have enough RAM to run TTS of TP2. These CAB's are attached.
The sys.txt files attached are what works for my ATT TP2. It took many hours to find the correct setting for each iGO8 version and I am providing them to make your process easier. If they don't work or you get some other error for what ever reason... I AM PROVIDING NO TECH SUPPORT. This is simply information for your use.
Good Luck!
PS. This works best if you have two micro SD cards. One for each version of iGO. That way if you add new contact address, you can simply pop out one card, geocode the data, and transfer the new gccache.dat file to the other card.
PPS. Once you do get everything working in iGO 8 properly.... DO NOT MESS WITH ANYTHING ANYMORE!!! iGO8 is one finicky bastard and will throw a TTS temper tantrum (refuse to load TTS) if you do... I know ALL TOO WELL!
DONT ASK ME FOR COPIES OR WHERE TO GET THE ABOVE PROGRAMS....
BUY THEM or USE SOME CREATIVITY.... like GOOGLE!
Hi:
Thanks for the great info. I have a few questions. The Mortscript seems to run clean RAM, and disable TF3D, but then TF3D starts back up on its own. Is this normal?
Also, is the script supposed to also start iGo, or must this be done manually; script did not start iGo for me.
Thanks again!!
The script is as written above. If the location of iGO8.exe is not where the script is pointed you 'll have issues.
RunWait("\storage card\iGO8\igo8.exe")
If you do not have a iGO8.exe in the above folder, you'll need to just make a second copy of application.dat in the same folder and rename it iGO8.exe. They are the same file, just different names.
Hi:
Thanks so much for your help. You were absolutely right, my .exe was in Storage Card/Program Files.
It is working well now.
Unfortunately it didn't make TTS work for me, but I have had problems with it for a LONG time, and never been able to find a fix.
Thanks anyway for everything
cincy1020 said:
Hi:
Thanks so much for your help. You were absolutely right, my .exe was in Storage Card/Program Files.
It is working well now.
Unfortunately it didn't make TTS work for me, but I have had problems with it for a LONG time, and never been able to find a fix.
Thanks anyway for everything
Click to expand...
Click to collapse
Were you using the above mentioned iGO versions? If not... I wouldn't know.
lokmeup said:
In order to have both TTS and Contact POI's working in iGO8 you're going to need two different versions of iGO8.
FIRST VERSION NEEDED: iGO8 v8.32.64029 (Nov 7 2008)
This version is designed for the PDA, and as such is able to geocode contact information. Install this version with the attached 64029sys.txt
At this point if everything is done correctly, iGO8 should boot normally BUT be VERY slow and unresponsive. This is GOOD! This is iGO8 Geocoding your contacts. Depending on the quantity of contacts with addresses you have, this could take a VERY long time. When it is done you will get a message similar to the following:
Geocoding finished with errors. 38 of 110 addresses found, 72 failed. Do you want to see the details?
At this point you could see the details of the errors, which will show you all of the addresses that are not entered into Outlook in a iGO8 palatable way. You could just ignore them and be happy with what you have (unlikely), or go back into Outlook, correct the formatting errors, and try again (and continue your suffering).
This can be VERY tedious... iGO is one picky bastard. You might even have to input the addresses into iGO as destinations, see how iGO formats the addresses, and then change the Outlook contacts to match the format iGO uses for a particular address.
I have even heard that contact need to be deleted and reentered into Outlook in the proper iGO8 fashion or you will continue to get errors for particular contacts.
SYNTAX ADVICE:
not Blvd. --> Blvd (The little "." will throw an error every time)
not Blvd --> Boulevard ("Usually" iGO dislikes abbreviations)
not N. --> N --> North (This is hit or miss)
NEVER use apt# (just give up and don't try)
NO Suite # (same as above)
If you have to have apt or suite #'s AND you want iGO to geocode, then the only way to get it both ways is to use the "OTHER" address in Outlook to place the iGO friendly address and the correct address in the "Business" or "Home" Outlook address. The ones with apt or suite # will error, but the second addresses in the "Other" address without the apt or suite # will geocode as POI's fine.
When you are done, you will be left with this little piece of GOLD... YOUR CONTACT POI's FILE ! ! !
\iGO8\save\gccache.dat
You'll want to back this file up somewhere else for safe keeping. We don't want all this hard work to go to waste.
SECOND VERSION NEEDED: iGO8_v8.3.4.102680 (Aug 13 2009)
This is the newest PNA version that does not have the ability to geopcode contact POI's, but it is able to read the gccache.dat file created by the PDA version above AND it is capable of TTS. Install this version with the attached 102680sys.txt
You will need to install this version and simply place the gccache.dat into the iGO/save folder and iGO will do the rest for you.
Now getting iGO8 to reliably run TTS is a different story. TTS requires ALOT of RAM to run. If there is not enough RAM available (~115-120mb), then it will simply refuse to play TTS voice prompts and you will be stuck with standard voice prompts. To get your available RAM to acceptable levels you will need to disable TF3D, run CleanRAM, and then start iGO.
Sounds complicated? Well, fortunately itsachirpthing over at PPCGeeks has created a nice little script that does just this. The original post can be found HERE. And the original thread can be found HERE. I recommend reading both these original threads. They have additional information to get iGO8 working properly on TP2.
I have added this iGO script to the MortScript.cab posted here. You need it and CleanRAM.cab. Install both to the device, not the SD Card. Then just click on the Plain iGO Scipt icon in the Start Menu. The script will close TF3D, run CleanRAm, start iGO8, and when iGO8 is exited, it will start TF3D again
The sys.txt files attached are what works for my ATT TP2. It took many hours to find the correct setting for each iGO8 version and I am providing them to make your process easier. If they don't work or you get some other error for what ever reason... I AM PROVIDING NO TECH SUPPORT. This is simply information for your use.
Good Luck!
PS. This works best if you have two micro SD cards. One for each version of iGO. That way if you add new contact address, you can simply pop out one card, geocode the data, and transfer the new gccache.dat file to the other card.
Click to expand...
Click to collapse
i tried this and all i have to say is ............THANKS!!!! this is the missing piece to my tilt2...i have asked around and no one seemed competent enough to know what i was talking about until now...the 64029 sys text fixed my intial boot up problem and now IGO is good to go...thanks again. God Bless
thesilentnight said:
i tried this and all i have to say is ............THANKS!!!! this is the missing piece to my tilt2...i have asked around and no one seemed competent enough to know what i was talking about until now...the 64029 sys text fixed my intial boot up problem and now IGO is good to go...thanks again. God Bless
Click to expand...
Click to collapse
Your welcome. I am glad my searching, suffering, trial and error have been helpful to others. I felt it would have been a waste of effort, if only my phone was to benefit from the knowledge.
Added both NOPushInternet_v2 and SSK TP2 Dynamic Resource Proxy CAB's...
Need for maximum available free RAM.
lokmeup said:
Were you using the above mentioned iGO versions? If not... I wouldn't know.
Click to expand...
Click to collapse
Hi:
Yes I am using the above mentioned Aug 13th version, but to be honest I have had this same problem since I switches to the R3 versions. Oddly enough, I only get TTS from "Amy", which isn't even a TTS voice, but her voice is limited, and doesn't include things like street names etc... When I try to use "Susan" or "Dave" which are TTS voices, they do not work at all. I have tried a million different TTS packages, as well as sys.txt edits, and still no luck.
I have searched and searched and never been able to fix it.
But anyway, thanks so much for posting your info, I am sure it will help others.
cincy1020 said:
Hi:
Yes I am using the above mentioned Aug 13th version, but to be honest I have had this same problem since I switches to the R3 versions. Oddly enough, I only get TTS from "Amy", which isn't even a TTS voice, but her voice is limited, and doesn't include things like street names etc... When I try to use "Susan" or "Dave" which are TTS voices, they do not work at all. I have tried a million different TTS packages, as well as sys.txt edits, and still no luck.
I have searched and searched and never been able to fix it.
But anyway, thanks so much for posting your info, I am sure it will help others.
Click to expand...
Click to collapse
I recommend reading the threads on PPCGeeks. You might need their recommended BRANDING.ZIP and DATA.ZIP files.
I know it is a pain in the ass... but it can work
but then again it can also stop working right after
Good Luck!
Lokmeup, thanks for the post. I found this by googling Igo8 and contacts... I'm running iGo8 (the most recent pna version) on my Imagio and of course it won't input the contacts.
I plan on following your directions but was wondering if I'll need to keep both versions available and run the PDA version every time I enter a new contact as the PNA version won't import contacts?
I miss the 'navigate to contact' from Tomtom but Tomtom doesn't seem to like the Imagio as it lags out while iGo8 runs fine.
Thanks in advance!
lokmeup said:
PS. This works best if you have two micro SD cards. One for each version of iGO. That way if you add new contact address, you can simply pop out one card, geocode the data, and transfer the new gccache.dat file to the other card.
Click to expand...
Click to collapse
Yes, It is best to keep both versions.
lokmeup said:
Yes, It is best to keep both versions.
Click to expand...
Click to collapse
Thanks and DOH! Didn't see that part about the other card. The damn SD card on the Imagio is behind the back cover and the cover is a beast to remove. I'll try to keep one internal and one external and see if that works. Thanks again!
Update: iGO 8 v8.3.2.97313 (Jul 3 2009) also works for geocoding. You can have one in main memory and one on your SD card and the one in main memory will geocode for the one on the card.
Thanks again Lokmeup, you gave me back the one function iGO was missing over TT!
Not to be a nay sayer, but why in the world do you need to jump through all these hoops to get TTS to work? My TTS works fine on 102680 with Igo as installed, I'm using the Energy 6.5.1 ROM but it's worked with every ROM I've tried it on?
For all of us obsessed with flashing, a lot of chefs are adding Sense instead of just TF3D. Sense will also cause TTS not to work. I have edited the mscr to disable HTC Sense before launching igo8 (and of course renenabling it upon exiting the program)
Two versions:
One that closes Sense then launches igo
The second closes sense, runs clean ram then launces igo
Personally i hate havng to confirm the cleanup, but your choice. Either one works out for me
IMPORTANT: RENAME file extention .txt -> .mscr (xda does not permit me to upoad mscr files)
marscandybars said:
For all of us obsessed with flashing, a lot of chefs are adding Sense instead of just TF3D. Sense will also cause TTS not to work.
Click to expand...
Click to collapse
Unless I'm really confused Energy ROM Phoenix has Sense in it, and it works fine with TTS on my phone without any scripts.
marscandybars said:
For all of us obsessed with flashing, a lot of chefs are adding Sense instead of just TF3D. Sense will also cause TTS not to work. I have edited the mscr to disable HTC Sense before launching igo8 (and of course renenabling it upon exiting the program)
Two versions:
One that closes Sense then launches igo
The second closes sense, runs clean ram then launces igo
Personally i hate havng to confirm the cleanup, but your choice. Either one works out for me
IMPORTANT: RENAME file extention .txt -> .mscr (xda does not permit me to upoad mscr files)
Click to expand...
Click to collapse
rename this file and just run it like the cab file I presume ??
Its working with the Sense file. I just went out and try it out. Would you be able to create a Sense file you created for igo mortcript and the htc addicts clean ram v1.8. ? I can see the other file as a shortcut in the start menu? Would you be able to create the same one for the sense version ?
Thanks.
I have a HD2, that came with a 15 day trial of CoPilot.
I want to use footprints but I don't want to pruchase CoPilot, when I click on the co-ordinates or address in Footprints it tries to open CoPilot, is there a way to get it to search the co-ordinates in google maps or orange maps?
Warning: if you try the following solution, you'll have disfunctions on your navipanel
for google maps the solution is very simple: just rename or cancel the folder CoPilot on internal memory of your HD2, or cancel the .exe of copilot inside this folder (splashscreen.exe too)
Or you can achieve the same results with a registry mod in HKLM\Software\Htc\Navisw
there's a key named SDKModule...just cancel or rename the entry (the default is \Windows\alksdk.dll)
choose the way you prefer
can u explain this detailed pls. is there a way to auto transfer coordinates from footprints to igo or other gps software.
any ideas how to transform the coordinates???
I managed to launch iGO8 with footprints, but that's all..It's just launching the igo application, but is not making a route to my footprint coordinates.I don't think this is possible.Igo must have a script to know that it has some coordinates to load. Hopefully HTC will release a .dll or something for other gps software then CoPilot or GoogleMaps.
All the best
traianboala said:
I managed to launch iGO8 with footprints, but that's all..It's just launching the igo application, but is not making a route to my footprint coordinates.I don't think this is possible.Igo must have a script to know that it has some coordinates to load. Hopefully HTC will release a .dll or something for other gps software then CoPilot or GoogleMaps.
All the best
Click to expand...
Click to collapse
hope to be fastly done, actually footprint is so nice application but without coordinate transfer it becomes almost totally useless.
i hope that problem to be solved.
meanwhile copilot looks like a kid toy in respect to igo, so its nonsense to use footprint only with copilot ...
qllkevuoi said:
Warning: if you try the following solution, you'll have disfunctions on your navipanel
for google maps the solution is very simple: just rename or cancel the folder CoPilot on internal memory of your HD2, or cancel the .exe of copilot inside this folder (splashscreen.exe too)
Or you can achieve the same results with a registry mod in HKLM\Software\Htc\Navisw
there's a key named SDKModule...just cancel or rename the entry (the default is \Windows\alksdk.dll)
choose the way you prefer
Click to expand...
Click to collapse
i tried exactly this, but when i click on the co-ordinate in footprints, it says "copilot.exe is not found"