Related
hi,
i can't seem to get it working. people can hear me, but i can't hear them
Anyone got this working?
Thx
it should work, i have not tested it but it should work, the files and registry entryes are taken from a hermes rom for which i am sure that it work and it is the same core and build as ours
i was able to launch the setup earlier... and decided to do it later on..
but when i tried after 2 days ... it just crashed...
did uninstall... softrest... install.. routine few times... and gave up.
I successfully connected to my Hungarian Voip provider (megafone) but no sound at all. Dialing is okay, but I cannot hear it ringing out, cannot hear the other party, they can't hear me. However the connection is there and the connected seconds are charged.
GSM phone, Skype and Fring are working well, only the Ms Voip has problems.
My settings look like this. The 'Dial plan' tab is empty. Is this normal?
Also noted that it didn't terminate the call normally as I pressed the red button, it kept charging on for 15 minutes of talk...
well now i think that something is missing, maybe audio encoders and decoders on which VoIP is dependant, i will look into this and will keep you posted
My tip is also codec-related.
Is it normal that via ActiveSync the voip says No Service? With WiFi it says Available, I think it should also with ActiveSync.
are there any news?
I don't have an issue with VOIP working on my SX66. In fact, I was surprised by how easy it was to get going.
-Chris
You were lucky that your provider uses the same codec as this WM6 build does.
Since I don't use something like Vonage, or Comcast VOIP, I just went out and found a VOIP provider online. VOIPCheap.com works great with this build.
-Chris
Many of us prefer a local VoIP provider though.
VoIP Incoming RTP
Some additional info on the problem with receiving audio. (same is on my phone). I checked which codec this SIP stack negotiates.
Apparently, out of all available, MS VoIP settles either on PCMA or PCMU depending on the other end availability, and refuses other most common ones.
Well, it encodes and sends RTP which I receive on other non wm6 phones and I am sure it receives RTP, and may even decode it, but by the look of it, not a squick is sent to the hardware/speaker.
Cheers
===
Sorted by installing Voip support from (ftp://xda:[email protected]/WM6VoIP.CAB)
and installing on top of the existing (from voip.cab - can't remember the source).
Although the dialplan tab is still blank (requires ipdialplan.xml, I guess) but the SIP settings are remain intact after this 'patch'.
====
I've just tested the MS voip with 3 different VOIP providers, and I also have the "sound" problem with it.
When I use an other VOIP application (like SJphone) all is working fine, so it must be a codec problem that is missing.
I just looked at VOIPCheap.com website. It's sounds interesting. Never tried VOIP from BA. Can someone tell me what i need to do to use VOIPCheap.com on BA to make VOID calls apart from creating an account with VOIPCheap.com? Thanks guys.
Never Mind. Please ignore my last msg. I think i got the answer on there website in FAqs. I'll create the account and see how good it is.
Anyone have any good/bad feedback for VOIPCheap.com service?
Thanks.
There are a lot of threads for VoIP problems in the forums many issues are solved there, i suggest al of the VoIP users to search and read there. Also i understood that difrend providers use difrend encoding-decoding so thats why it works for some and not for everybody
did someone find a fix for the muted audio issue?
i've read many threads about many voip issues on the other forums available here, but it seems like the small amount of ppl who had this problem was left quite alone..
I'm trying to place calls via my asterisk 1.4 box.
thanks
Hi,
I have a t-mob wing (after I drove over my magician and I have the following problem: When I am having an active data connection I cannot receive any voice calls. The calls are going directly to voice mail, without notifying me. Once I stop the data connection I can receive calls again and than I will see that I missed a call.
I talked to t-mob support, and after doing a hard-reset (of course) they told me that this is a known problem with the wing, that they are trying to fix it and that there is nothing they can do right now.
1. do other wing users in the US experience the same, so is it the default behavior, or am I just unlucky? (it worked great without a problem with my magician btw)
2. as sometimes during the day the internet connection automatically gets connected (activesync I guess) I never really now if I am able to receive calls right now. Is there a workaround to manually start up and stop the internet connection without the device automatically connecting whenever it feels like it?
thanks in advance
wolferl
interesting ...
I have had a lot of complaints from people telling me that when they call me, it goes straight to voicemail.
I'm also a US Wing user, and I can confirm that is happening to me as well. Was checking sports scores on my break at work earlier, and my girlfriend called me, and I got a voice message from her...but it never showed that she called.
I also have the issue with people in my fave 5 not showing in the call history anyway, so I guess I lose both ways.
hm,
ok, seems to be a generic problem. Is here anyone who successfully gets voice calls while on a data connection with a wing/herald/p4350?
would be interesting to see if it is a t-mobile or device problem.
thanks
I got a HTC wing and i still get incoming call while browsing the internet. No problem here. i've tested a couple times and they all went through. I have T mobile
hondaman82 said:
I got a HTC wing and i still get incoming call while browsing the internet. No problem here. i've tested a couple times and they all went through.
Click to expand...
Click to collapse
hi hondaman,
thanks for the info. whats your provider?
thanks wolferl
"active" data connection is the key
I have the same problem, no voice calls with an active data connection. For me, it seems to be only when the data is actively transferring, like streaming audio or a largish download. Straightforward web surfing doesn't seem to cause the problem, I've received multiple calls while surfing. But during streaming audio, calls go to voice mail every time.
I swear to you, I get calls when I am using data all the time on my Wing. I have the stock T-Mo rom and everything. No CID unlocking, no SIM unlocking.
It happens to me alot that people complain they have called me and it goes straight to voicemail... and its been in cases where im not even using my phone, and as far as I know, I have good signal.
I was running this GB soft program that kept my data connections always on... so I stopped using that to see if I notice a difference.
On the T-Mobile MDA it worked just fine, but on my Wing I can't receive calls while online either.
I just did some testing and I need to correct my original statement. Looks like kerrkj and the others were right. Just being online does not stop you from receiving calls. Just when you are transferring data, the line being actively used, you are not reachable. So, when you are web browsing, it depends whether the moment the call comes in, data is transmitted or not. I was testing accessing different web pages and a couple of times it worked and a couple of times it did not. When streaming audio the calls went to VM 100% of the time.
So, when I am using tomtom and having the traffic check activated, it will be pure coincidence whether you receive a call or not. When streaming audio it will be guaranteed that you are not receiving calls.
I am pretty sure that it was not like that with my magician. Hopefully t-mobile sorts it out sooner than later.
thanks for all your feedback
wolferl
it happens to me too, i know on sprint with the treo's you can run internet or phone, all calls will go to voicemail if you are on the internet. i just assumed it was that way with all of them.
I was able to get Internet Calling (integrated VoIP) on the mogul working with the Gizmo VoIP service. The big problem is that the volume is so low it is pretty much unusable. I followed all of the guides here on xda and came up with the same issue as everyone else; i could not get internet calling to show up on the today screen and i did not have any of the internet options under the phone settings. What solved it for me was Schap's Setup VoIP tool version .3. This tools gives us the ability to now set the items that us Mogul users do not have available under the phone settings.
In a nut shell:
1) install WM6VoIP.CAB then reboot
2) install SetupVoIP_v0.3.cab (Schap's VoIP tool)
3) open Schap's config tool and set:
a) all of your SIP settings.b) Set outgoing calls using VoIP to Whenever available.c) enable VoIP over 3G.
Now when you go to your phone dialer it should now show the name of your VoIP service at the top rather than your carrier (Sprint PCS in my case). You will have to force your internet to connect first (i use PIE to start my internet connections up, not sure of a better way to do this.) Now you will be able to make and receive VoIP calls. I have verified this by calling another phone and seeing that the caller ID is from my VoIP. I have also been able to stay on a call and browse the web at the same time (not normally possible on sprint). The 1X icon never appears over my Evo icon while on the phone now. Interestingly enough i could not get this to work over WiFi, it would only work on Evdo.
This integrated VoIP is so seamless that it pains me to use another app just because of this volume issue. I have tried:
Skype. Works great, but not with Gizmo.
SJPhone. Works with Gizmo, but is VERY choppy.
GoSip. Works great with Gizmo, but is very big and slows the phone down.
Fring. Works great with Gizmo and the mem usage is great, but has no dial pad and that pretty much makes the app useless.
Wengo. Works great with Gizmo. Mem usage is on the big side, but is manageable. Seems to be the best for me so far.
I have tried many others that either work as dial out only or only work with their makers SIP service.
Any other ideas or thoughts?
Thanks,
JD
You got the mic working using Fring ? I always got one way audio
What version of WM6VoIP.CAB did you use ?
The mic did work for me on fring. However, the instant that i realized that i didn't have a dialpad i removed it. I use VoIP mostly for conference calls and i need to be able to enter in conference room passwords.
How would i be able to tell what version of WM6VoIP.CAB i am using? I cannot find version information anywhere.
JD
You are lucky with the Fring since there is many complaints from Mogul owners that Mic doesn't work
What version did you use ?
When I was searching for the WM6VoIP.CAB there was indication that there is some new version but the link was dead when I tried to download
Can you please post it here?
When i tried Fring it was a few months ago and i don't remember the version number. I do remember using my bluetooth headset for SIP rather than the internal mic and speaker. I just tried the newest version of fring (downloaded last night) and my internal mic and bluetooth headset now do not work for SIP. Interesting.
For WM6VoIP.cab I searched here on XDA and downloaded the first link i found. Here is the one that i used, not sure if there is a newer version? http://218.93.115.138/d900/patch/WM6VoIP.CAB
JD
That's the same I'm using ... I did read some article about this couple weeks ago ( can't find it) where there was reference and non working link to new version of this file.
Did you read this post ? :
http://www.eten-users.eu/lofiversion/index.php/t8854.html
There is reference to switch.cab ( can't find link to download it )
switch.cab
Try this:
http://www.etenblog.com/downloads/Software/switch.cab
I did, it did install ok but it doesn't work
Thanks
well i tried the configuration and everything, but the thing is that when i try to call out it says dialing then it says call ended, like it doesn't even ring. I entered the correct settings and everything.
I did everything and it DOES NOT show on my Today screen, I see the item "Internet Calling" checked in the today screen options. Any ideas?
Telus phone right ?
I if so that's normal with the Telus ROM
lifeisfun said:
Telus phone right ?
I if so that's normal with the Telus ROM
Click to expand...
Click to collapse
No, I have a Sprint Mogul with the "unofficial" leaked GPS rom. Anyone else know how to fix this? I really need this to work, thanks a lot.
It will not show on your today screen. When you go to your dialpad, the name of your VOIP provider should be listed at the top rather than sprint. If it shows that then you should be good to go.
JD
When you make a call, does the sound come through the earpiece or the speakerphone?
How can I have the sound coming from the speaker on the screen side instead of the back speaker?
Thanks!
I'm afraid you can't
I have been trying to find an answer to this all over the forums. Has any of the cooked roms enabled the VOIP capabilities back into the phone?
I am using the VZW 6800 and would love to be able to dial over wifi with my asterisk server. I know VZW removes this feature, but I have not found out whether any of the cooked roms, including DCD's roms have added this back in.
If anyone knows, or has used this feature, please let me know your experience.
Thank you!
Check the last pages of this thread and you should be good to go. Over wifi things are good but over 3g it's not.
http://forum.xda-developers.com/showthread.php?t=299950&highlight=voip
I have gotten the voip stuff working on my sprint mogul w/ the sero plan (connected to gizmo), but there are a few things that keep me from using it:
a. even though it *does* work over the EVDO connection, with both evdo and wifi the outgoing audio is really clippy (both bluetooth and wired headsets tested)
b. for some reason, when I have voip enabled I can't get phone service half the time... it's like I put a 6db attenuator on the receiver and it only gets service if I have really good signal to the tower
c. the audio is so quiet that it's virtually unusable that way
follow the above linked thread, I think that's where I got my info as well.
Also, keep in mind that the 'net connection you use has to be initialized when you try to make/receive a call (use PIE if need be, particularly when using the phone's internet connection rather than wifi), and in order to make outgoing calls, you'll have to make your own dialplan. (edit ipdialplan.xml)
I can post mine, if you want, I just don't have it with me. if you would like me to, PM me ('cause I might forget to check this thread again) and I'll post it here.
I was wondering if you clever devs could look into adding phone functionality to the adam 3g model ?
it should be capable and would be handy for the odd occasions with a bluetooth headset.
The early tablets and recently at ces the tablet had phone icons on the desktop so im sure its at least a possibility !!
many thanks in advance
On the Battery Use, I have seen a "Phone" process.
Maybe it is already activated, but not used
You can get to the phone section via "contacts" but when you try to make a call it says "call ended" after you hit the call button. From the FCC docs, it says that the Ericcson F3307 3G card is "voice" capable so in theory it is possible! The only thing even close to phone functionality that does work is the sending/receiving SMS messages atm.
Just a shot in the dark, but does google voice's data calling use the same process?
yes and it sucks. it only stinks that the google voice works over data and not wifi. so i cant make a call over wifi if i dont have a valid sim card in.