Hi everyone
I have searched through numerous forum post and development websites to find these answers (has taken a couple of weeks, with no help from $&% Telstra), so I thought I would put them all in one post. I don't take credit for any of the work arounds, I just figure there is a lot of individual posts without the answers in one spot.
Tip 1:
Don't use the default GMAIL settings as this doesn't allow you to actually specify to connect to 'The Internet' and is default set to Telstra Internet (was for me anyway). There is a good step by step guide on the GMAIL website - create a new acounnt but the key is to not enter gmail.com as your email address as it automatically detects the settings and masks/blocks the advanced screen. By following this, I could then have GMAIL on my WiFi with no data plan enabled (long story)
Tip 2:
Do this to configure a new Telstra Data connection as the default one can't be modified:
(link to be approved so msg me and I will send in mean time)
However make sure the 'This network uses a proxy...' part isn't checked, opposite to the guide on the above link.
Doing this actually meant my GMAIL could now connect using the DATA plan but by default used the WiFi when it was connected.
Tip 3
The ActiveSync and Exchange part is by default configured to Telstra's dedicated email plan. On my phone there was actually a PDF on the storage card about this and also a step by step guide on how to configure your ActiveSync/Exchange to connect through the normal internet, not through Telstra's plan. However, as I have seen many similar examples on the internet, following this procedure was great except the settings would not save. Changing from 'Dedicated' to 'Internet' never actually accepted.
I was determined to figure this out, so installed a registry editor. With some snooping I found enough information to be dangerous and did some searching, and found this link:
(link to be approved so msg me and I will send in mean time)
If you go to the bottom about Network Registry Settings, the key one is:
HKLM\System\ActiveSync\SyncAPN
By changing this to 0, my 'Internet' setting would save for the ActiveSync/Exchange and sure enough, connection to my exchange server was succesful.
CeRegEditor is the program I found really simple to use.
Tip 4
Install these two free applications for Data Connection management
Good for Enabling/Disabling Data Connections - DataController.CAB
I don't fully understand the full power of this one, but it is good to see what is happening and has an auto disconnect: BandSwitch.V2.8.CAB that is mentioned in the registry tips/tweaks section, tip 50 or somewhere there abouts.
Tip 5
Cookies Home Tab - sensational!!
Tip 6
Unlock the quicklinks (plenty of posts on how to do this) and also remove the non-used Telstra Home-Tabs (well I don't use them as they always have a wap redirect to m.bigpond.com)
Tip 7
If you are facebook user, check out the 'touch' version. Go to m.facebook.com and down the bottom there is a link to facebook touch
So that is about it for now, following all the above, after a hard reset worked a treat without having to install a non-telstra ROM.
Hope this helps, like I said, I don't really know all the details of the work arounds, more just posting them all in one spot for future frustrated people with the Telstra version. I am loving the phone now (also have followed other registry tips from this site).
Happy using and massive thanks to all of you who actually did figure out the solutions!
Jason
Thanks for this.
The Dedicated/Internet drop down box does work without the reg hack but it resets itself back to dedicated.
I found also that I had to make a new connection to telstra.iph for activesync to stay connected when the screen was off.
Woudl greatly appreciate if you could send me the missing details above. I have not managed to get WMDC to recognise the phone yet so can't, and not keen to yet anyway, replace the Telstra ROM.
i get "Access Denied" when i try the registry hack, anyone else come across this?
I did get that, within the Registry Editing software there is an option to unlock the registry, once you do that you can then change the settings!
Thread Links
Have put the thread links in the txt file
Problem with Telstra Connection
saxjase said:
Have put the thread links in the txt file
Click to expand...
Click to collapse
Hello, I have the Telstra T9193 here in Argentina and I want to use with other internet carrier, I configured the connection and Internet is working fine but I can't check the emails....
So I think that the problem is the default Telstra connection, maybe only the ROM permit use this connection to check emails.
Could you know something about it?
Thanks
Hi Diegogleo
Which email are you trying to check? Webmail like GMAIL or Hotmail or a separate pop3 account?
If it is hotmail, the default windows live setup seems to work fine.
You have to change the settings of your email account to use 'Internet' not 'Telstra Internet' (or whatever pre-programmed data connection might exist). That way, when you are in WiFi or using your Mobile Providers Data, you can pick email up.
If it is exchange mail, you will have to do the registry edit above.
saxjase said:
Hi everyone
I have searched through numerous forum post and development websites to find these answers (has taken a couple of weeks, with no help from $&% Telstra), so I thought I would put them all in one post. I don't take credit for any of the work arounds, I just figure there is a lot of individual posts without the answers in one spot.
Tip 1:
Don't use the default GMAIL settings as this doesn't allow you to actually specify to connect to 'The Internet' and is default set to Telstra Internet (was for me anyway). There is a good step by step guide on the GMAIL website - create a new acounnt but the key is to not enter gmail.com as your email address as it automatically detects the settings and masks/blocks the advanced screen. By following this, I could then have GMAIL on my WiFi with no data plan enabled (long story)
Tip 2:
Do this to configure a new Telstra Data connection as the default one can't be modified:
(link to be approved so msg me and I will send in mean time)
However make sure the 'This network uses a proxy...' part isn't checked, opposite to the guide on the above link.
Doing this actually meant my GMAIL could now connect using the DATA plan but by default used the WiFi when it was connected.
Tip 3
The ActiveSync and Exchange part is by default configured to Telstra's dedicated email plan. On my phone there was actually a PDF on the storage card about this and also a step by step guide on how to configure your ActiveSync/Exchange to connect through the normal internet, not through Telstra's plan. However, as I have seen many similar examples on the internet, following this procedure was great except the settings would not save. Changing from 'Dedicated' to 'Internet' never actually accepted.
I was determined to figure this out, so installed a registry editor. With some snooping I found enough information to be dangerous and did some searching, and found this link:
(link to be approved so msg me and I will send in mean time)
If you go to the bottom about Network Registry Settings, the key one is:
HKLM\System\ActiveSync\SyncAPN
By changing this to 0, my 'Internet' setting would save for the ActiveSync/Exchange and sure enough, connection to my exchange server was succesful.
CeRegEditor is the program I found really simple to use.
Tip 4
Install these two free applications for Data Connection management
Good for Enabling/Disabling Data Connections - DataController.CAB
I don't fully understand the full power of this one, but it is good to see what is happening and has an auto disconnect: BandSwitch.V2.8.CAB that is mentioned in the registry tips/tweaks section, tip 50 or somewhere there abouts.
Tip 5
Cookies Home Tab - sensational!!
Tip 6
Unlock the quicklinks (plenty of posts on how to do this) and also remove the non-used Telstra Home-Tabs (well I don't use them as they always have a wap redirect to m.bigpond.com)
Tip 7
If you are facebook user, check out the 'touch' version. Go to m.facebook.com and down the bottom there is a link to facebook touch
So that is about it for now, following all the above, after a hard reset worked a treat without having to install a non-telstra ROM.
Hope this helps, like I said, I don't really know all the details of the work arounds, more just posting them all in one spot for future frustrated people with the Telstra version. I am loving the phone now (also have followed other registry tips from this site).
Happy using and massive thanks to all of you who actually did figure out the solutions!
Jason
Click to expand...
Click to collapse
Hi Jason...thx for the GMail solution. Still haven't gotten it to work and it is most frustrating. I have another question...what is the correct procedure for installing these .cab files? Again...something else i've tried and doesn't work. Any help would be appreciated!
Cheers
George
Related
Assistants required!!
I have attempted to set up GPRS on my M600 (Unlocked for Vodafone sim)
GPRS has been enabled as I have the G icon up!
I have been on the vodafone website and tried there settings with no luck!
I have been on the Filesaveas website and plugged in all of those settings with NO luck, Have also installed the I-mate .cab again with no luck!!!
I am starting to go insane spent three days trying all different settings and No luck at all!!!!
You name the website and I think Ihave probably tried it.
Does anyone have any useful advise for me, provide me with some form of sanity check!!!!
Ideally I wold love a .cab file to install!
But would like feedback from anyone else in a similar position, on how they resolved this some what annoying issue!!!!
regards
Wilko_007
I set up my Vario II for Vodafone with no problem. These settings (*.pdf file) seem to be the same as the ones I used, see how they compare with the settings you are using.
Many thanks I will give it a go!
Ok have now got connection but I can't surf?
I have seen comments about GPRS beening fully enabled?
Are there 2 forms of GPRS that can be enabled? WAP & WEB???
Do I need to worry about the Dialing Rules???
Thanks in advance for your assistance!!
[/img]
Could you be a little more specific i.e. does it come up with a pop-up box stating that it is connecting to GPRS? If yes, which connection does it say it is connecting to, is it the correct one (i.e. the new GPRS settings that you have just keyed in)? When you say it won't surf, what do you mean exactly ... are you using Pocket IE and does it come up with any error messages etc...
Connection via GPRS No probs I then get the Small G and the two arrows fixed on the bar.
Enter IE and type google for example.
get the status bar flash up breifly and then disapear, with no change to the original Orange World Home page!!!
No errors what so ever????
okay ... the next thing I would probably do then is download an alternative browser to see if it still happens in a different browser. Netfront is pretty good. At least that way you should be able to establish if it is a GPRS problem or a browser problem.
Ok I now have installed Netfront and connected to the GPRS!
typed in www.google.com
I have a warning screen:
Browser Warning
Cannot load Page
Type: DNS no server is specified
?????
Okay .. I am running out of ideas now, it does sound like your GPRS Settings are still wrong.
Click 'start menu', 'settings' and go to the 'Connections' tab. Now click 'Connections', then the 'Advanced' tab then 'Select Networks'. The first box (ie. Programs that connect to the Internet automatically) should say 'My Isp' and if you click 'Edit', it should show you 'Vodafone Internet' is selected.
If you then select to edit that, you should see in this order 'Vodafone Internet' and then it should show modem type as GPRS, next page should show Access Point Name of 'Internet', next page should show User name 'Web' ... password is the same, domain field should be blank ... nothing needs to be done in the advanced tab because the default of 'Use-server-assigned IP address' should automatically be selected, same for the server tab too, default should be server-assigned.
These are the settings that work fine on both my XDA Mini S and my MDA Vario II.
Right I have checked both ISP and MyWork Network, all correct!
The only thing I can see is that the password box has loads of characters (*'s) instead of just 3 *'s for WEB (***)
But every thing else is as the PDF??
Stumped!!!!
you can try messing with the newly released ms network tools there is a link in development forum
or you can try manualy typing in a know dns server in the settings
unless the gprs dont route the request
any dsn server ip will do
same as pc's really
I am afraid I don't know then ... we have reached the level of my knowledge (which isn't high )
Perhaps somebody with a little more technical knowhow on GPRS issues may be able to help you.
Sorry I couldn't get it sorted for you.
Thanks for your help a least I can connect now!!
Thank you again!!
anyone heard of the connection No. being *99#?
Vodafone instructed me to put that in the setup?
I guess that goes in under the " My Work Network" Vodafone Wap - Number?
This is now becoming a huge headache anyone got any ideas?
not sure how vodaphone handle it but i never heard about
ppl having to add numbers when they picked gprs as connection
belived that was only if you connected around grps
Wilko_007 said:
Right I have checked both ISP and MyWork Network, all correct!
The only thing I can see is that the password box has loads of characters (*'s) instead of just 3 *'s for WEB (***).
Click to expand...
Click to collapse
I'm expericening a similar problem.
My phone was sold as an O2 XDA Mini S. My O2 contract/account doesn't allow GPRS (they want me to upgrade) so I tried my Vodafone PAYG SIM and it works without having to have the phone unlocked in any way. By that I mean I can use voice calls and using the settings I've found through this site I can send MMS messages via GPRS but I cannot connect to the internet. I've checked with Vodafone and the account will allow internet and GPRS etc.
The only thing that I can see that is wrong is the password. Whenever I type "web" then finish, it always defaults back to a string of 16 ***'s when I re-check the settings.
I've even done a hard reset and used the corporate install to no avail. I don't want to run any sort of unlocking software if I don't need to as I don't want to create a very expensive door stop.
Any ideas?
The string of asterisks is normal, I think it is just a method used by Windows to make the password more difficult for someone to guess i.e. by disguising not only the characters but also the number of characters.
I just double checked and my fully working settings also show a row of asterisks despite it being a 3 character password.
Thanks Nicky
I'll keep plodding away with this but hopefully someone might steer me in the right direction soon.
;0)
Hello guys
I am suffering for a few days on this issue in HK..
I just sim-unlocked my x01ht by M3100v4Unlock from Imei-check(OS is still Japanese), and try to setup my environment one by one.
However one of simple setting to connect by Gprs still has problem..
Please help me if you guys have any idea.
Summary of my situation:
1. GPRS (by Peoples SIM) : can connect but cannot see web site by IE
2. 3G (by CSL SIM) : can connect but cannot see web site by IE
3. Wifi : can connect and no problem to see web site by IE
for case 1&2, IE error message says "Cannot show page, please check the address and try again".
It seems address is not solved into IP address(Like cannot find DNS server)..
howver i still don't have any solution..
Would you please give me some advise for this problem?
Thank you !
go to start>settings>connections>connections>connections>advanced>select networks> and in the drop down list select the connection you are using to access the net.
fone_fanatic
Thank you so much for your quick reply.
I just checked the setting you taught me,
However I found out I already selected the appropriate setting you mentioned.
Normally for WiFi connection I select "My Work Network" &
for 3G/EDGE I select "My ISP Connection".
Also make sure all the APN, username & password correctly enter.
ghz
Thank you for your suggestion.
I checked APN, Username & Password is correctly inputted.
Today I also brought my x01ht to support centre,
let the enginner set up, but still have problem.
when I use this sim on my HP rw6828,actually no problem.
(That mean sim has no problem.)
Thank you
I have a similar problem, see this thread
http://forum.xda-developers.com/showthread.php?t=293494
are you using a cingular ROM?
Hi,
I installed Opera for wm5, then can go to any website now!!
That means IE caused this problem, but don't know exactly what the problem is..also can't find how to update IE..
Anyway, I use opera at this moment.
Thank you so much!
cpz21,
Thank you for your information,
I just deleted the registory you mentioned
then I can connect to any website now.
So everything is clear!!!
Thank you
glad that helped.
I still have the problem...
cpz21,
Sorry, I was so happy by myself.
I'm using genuine softbank japanese version bought in end of Dec.
As I am new in this toy, can't give you good advise at this moment..
Thanks akind. I'm mostly using opera 8.6 right now, or I can restore registry, or just not to sync with home PC (sync at work seems ok)
Sooner or later I will find the reg key
Hi cpz21
Last night I hardreset my device and setup from the beginning.
Of course I deleted the reg key and test IE then no problem.
However, this morning i went to web by IE in subway through gprs, it can't show web page.
Then I arrived office and checked the reg key again, found it still there...
Don't know why it come to be like this..
Just for your information.
Help...
I have a HTC 3600 (handy as I'm posting in this forum ) and I have been trying to connect it to my work wireless setup. This is fairly locked down and has a hidden SSID and requires me to enter credentials (user name, password) to access the web. I can successfully connect to the Wi-Fi, I am issued with IP address etc but can't then take the next step to connect it to the web.
I have found an area to add a proxy with username and password - I do this but still nothing. One odd thing is that when I then go back to try editing the proxy settings 9 times out of 10 it has vanished and I have to create it again!!
This is causing much hair pulling!
Any direction/help in this would be great as I am now a little stuck.
I am on AX3L v3.0.9 build.
Cheers
Update
I have found out that if there are two settings in the connections summary - such as 'My Work Network' and in my case 'etisalat UAE' the proxy setting never gets lost. Is this a quirk, is there something that I am not understanding (I know the obv. answer to the last question is yes!)
This now brings me to my nest challenge which is how do you arrange these connections? What I mean is that if I am at work/home and have a wi-fi link active how do I get the device to pick this in preference to a GPRS connection which it should use at all other times? I have tried looking for some kind of guide so I can work through this my self but no luck so far..... if anyone knows of such a thing or can point me in the right direction then please reply to this.
Cheers
Hi everybody!
I have a little issue using my work's exchanger server connectivity on HTC Touch Pro.
Issue: To access internet, my provider uses their "walled garden" APN, which allows me to access their services & general web.
This APN, however fails to work with Exchange.
To overcome this, they have given me another APN, which allows me to access Exchange/Push & Internet but not their services.
Now, it is really, REALLY annoying have to change APNs every time I need to access different info (web vs. provider's page) and I have not been able to find anywhere to specifically point Active Sync to use the required APN as it only has option for "Internet", which I assume is the generic active access point
Dialling rules also are useless as I'm using HSDPA with no proxy to access web.
Apologies if this is all too confusing and thank you in advance for your assistance
http://forum.xda-developers.com/showthread.php?p=2382465
http://forum.xda-developers.com/showthread.php?t=440593
Thank you!!!
So I have done that and can have 2 multiple APNs running at the same time!
It seems, however, that both connections have to be "ON" at the same time as when all APN are disconnected, it doesn't chose the correct data account but always the one that is higher on the list.
Is there a way to overcome this - is there a way to prioritise which data account I want to be used first?
Thank you again
LHD said:
Thank you!!!
So I have done that and can have 2 multiple APNs running at the same time!
It seems, however, that both connections have to be "ON" at the same time as when all APN are disconnected, it doesn't chose the correct data account but always the one that is higher on the list.
Is there a way to overcome this - is there a way to prioritise which data account I want to be used first?
Thank you again
Click to expand...
Click to collapse
Hi, I have a HTC Kaiser with BlackBerry Connect and I don't have the issues you describe. BBC creates it's own APN which is not used for anything else. In 'Connections' I have 'My ISP' set to use the Vodafone APN I manually defined. Under normal circumstances BBC keeps its own APN connection active, if I open IE or another app that uses the Internet then the Vodafone APN activates and the apps send their traffic over this connection.
One issue I have is that there is no way to disconnect only one APN connection, when you click 'disconnect' both APN connections are closed, however a few seconds later the BBC one reactivates.
EDIT: Sorry, scratch that... For some reason I though you were using BBC - don't ask me why, obviously my brain was wandering elsewhere. But back to your original problem. I don't use Exchange ActiveSync and I don't know if you can configure ActiveSync to use a specific APN like BBC? You might be able to configure the Exchange Servers URL to be in your Exceptions list so it uses your 'My Work Connection' instead of the 'My ISP' and therefore uses a different APN? I am not sure if it would work, but worth trying?
Andy
HTH
Andy
Hi guys, I been browsing the forum for a while - decided to sign up now due to getting hold of my first smart phone.
I've set up my email account (pop3) it worked the first time yesterday, received and sent emails.
Now today, when I receive I get nothing, no messages, and when I send one i get this message:
"cannot connect with current connection settings. the change your connection setting, tap settings."
clicking on settings brings up the t-mobile settings tab etc, but I'm not sure what to change here as I'm pretty new to all this!
and I'm just wondering if I need to change anything - as it worked yesterday but not now even though i haven't changed anything.
Any ideas?
Thanks in advance.
I used to get all kinds of hassle like this with my HTC Advantage. It would work perfectly for a while, then it would not allow access, so I'd have to re-input the SAME settings all over and it would seem to work again (fortunately, it seems to be pretty well behaved nowadays!)
So long as your pop3/send/recieve/SMTP settings are all good [make sure that login names etc are all as your email provider states, usually full email address and password and smtp/outgoing *DOES* require authentication]- sounds like you might want to check on your connection settings (I assume that the internet is not working either? Or MSN messenger?) B4 going into settings you will need to find out EXACTLY what your APN (access point name) address is for your specific carrier (there are typically several ones per carrier - usually one for contract and one for PAYG) and the user name and password.
Then check/update your connection settings. You can go and edit the existing setting - you will need to choose a name for it (there should be a default) and then you may have to 'select a modem' - typically I select 'Cellular Line (GPRS, 3G)', as it works best for me [on another device however, I select GPRS only, as there is poor 3G reception here in the office and it causes the connection to find a 3G signal and try to connect to it, to no avail though and thus it drops the connection - but hopefully you wont experience this!]
Next update your: 'APN' and the 'User Name' and 'password' (those 3 things will be supplied by your carrier) and save it. And HOPEFULLY that should do it - it can get a little more complicated than that, but I'm hoping that you dont have to get into setting up work networks/proxy servers etc - I can do that and have some data for it, but I'm not very good at exaplaining it I'm afraid it's something I've learnt on a trial and error basis, as I'm not a techy/network specialist AT ALL
HTH
double post*
thanks for your reply!
as far i know all my email info is fine, but I shall try again after work. only details I might have to get is t mobiles. might have to look on the net. but i'll try what you've suggested.
but the net is working fine! I'm using it now...will give it some trail and error.
thanks, and till later!
In which network are you? And which country?
Hello - I'm on t-mobile in the UK
I'm thinking of doing a total hard reset - now my googlemail isn't working ! and that was yesterday.
Just for good orders sake:
T-Mobile APN Configuration
For both contract and pay-as-you-go T-Mobile customers in UK the following APN settings are used:
Name: TMobile GPRS
GPRS APN address: general.t-mobile.uk
Username : user
Password: wap
- other settings can be left blank.
Apologies if you already know how to do this, but I just checked on the HD2 and you do the following;
GOTO the Settings tab (last one).
Hit MENU (bottom right)
Hit CONNECTIONS icon
Hit CONNECTIONS
Select (if you're accurate enough.... ) 'Manage Existing Connections' and follow the path - you may want to just re-input the above to make sure you know all is well then save it (finish)
Just a thought.
Thanks alot for that blackblade, i can use that as reference, will try again in abit - I've done a phone reset for now.
cheers fella. very helpful.
well guys, I've tried checking and changing those details - still no joy. Not sure what to do with this now to be honest!
Not sure if you've resolved this, but I had the same problem with t-mobile.
You need to deselect "use proxy server to connect to the internet" in the t-mobile internet settings, for some reason this gets selected on set up. Once you've done this you should be away!