I'm lookin for long time a solution to route the S200 sounds to earpiece from external speaker during voip calls.
No success.
I have tried 4-5 programs (audioroute, speaker switch etc.).
Anybody have solution?
Related
I have a couple questions about my KJam
1) Does anyone know where (even in the registry) to adjust the mic sensativity? I am not talking about AGC. I use a voip program and the mic is too sensative and cause echos for the other party.
2) Anyone know how to use a bluetooth headset to work independant of teh phone and voice dialing? I would like to use it with my voip software but when it connects it only activates the voice command program then disconnectes if not used for that. I would like a way to just transfer the ear speaker and mic to the headset until switched off. My heaset is paired with the KJam in handsfree mode.
3) Anyone know where I can get the part to replace my keypad? I have the arabic/english keys and would like only the english version. I already changed the software and not just want the keypad membrane itself that I could change.
4) Anyone know where to find a disasembly guide/manual for the KJam?
Thanks, John
PS: the voip program works great!
www.skynetworks.gotdns.com
What VOIP are you using?
I am using the SJLabs softphone with Vonage. Bye the way, it works great if I use an external earpiece headset like the one that came with the KJam. The built in mic is just too sensative and picks up the sounds from the built in earpiece. Although it doesnt do this when using the phone in normal calls.
The fact that the mic isn't too sensitive when using the normal phone indicates that it's more of a problem with the softfone sotware. Perhaps it's setting the mic gain too high.
Have you tried another softfone? Other than that, if you try a different headset and mic but then you may find the mic not sensitive enough for normal phone use.
I would try another softfone first.
Yep, I have tried different softphones. Still the same. It seems that the mic volume is different when using the normal phone function than it is when using programs. The softphone doesn't have a mic sensativity adjustment and states to adjust the mic in the control panel of windows ce. But 2005 doesnt have an adjustment. It just has the auto gain control on and off mode.
Well I went ahead and purchased the softphone from www.xten.com and it works great. I also have ineen installed and working.
Anyone have any suggestions on my other questions?
Hi there,
I have not read the complete forum so I don't know if this has been discussed already, but I am stuck with this wierd problem.
I used to run 2.0.64.wwe on my T-Mobile MDA and this worked fine in combination with my carkit.
Because of some GPS bluetooth problems I upgraded to 2.01a.64.wwe.
When the phone is in the carkit, I can hear incoming sounds, I can recorde voicenotes (so the mic connection works), but when answering a phone call, the mic is muted.
I have tried with Mic ACG on and off, but there is no noticable difference in these situations.
Anyone got a clue?
Thanx,
Patrick.
Hi! Something happened with my O2 Atom and nobody can hear me when I making a call while I can hear them perfectly. Can make audio notes - microphone is in working state. Have tried different providers as well as ROM-update. Still not working. Any ideas? Thanks!
Atom has 2 mic. One for recording located in front of the phone, next to the signal led. The other one uses for phone call only. Sure that your mic for phone call is bad, it is located at the bottom of the phone, you can see there is a small hole near the headphone jack.
I have the same problem
Yeah, I have the same problem with some calls
I have same problem too, i cant heard out/in-ing call. Anyone can help me to solve it??
I found my Atom Xda having the following condition:
When blue tooth off, no problem for voice incoming and outgoing.
When blue tooth on and connected with my wireless blue tooth ear piece, the hand set's mic become useless during outgoing call and must use the ear piece to communicate; but this is not affect receive the incoming calls, both incoming and outgoing voice working ok for incoming call.
Hi to everybody,
I'm using skype 2.2 beta on my p3600, everything is working fine but I have a question for you...
The incoming call voice come from the rear speaker instead of the front speaker like a normal phone call.
So I need to increase the volume to ear properly or use a headset.
It is possible to redirect the sound (incoming voice) from the rear speaker to the front speaker?
Thanks in advance
Gianni
Thats the same with mine, and as far as I know there isn't a work-around for this yet.
Hi,
I have the same "problem". I tried also the following VOIP programs: Fring, SJPhone, Expresstalk and Wengo. All of them use the rear speaker for the incoming call.
For this reason I used headset.
I hope someone is able to find a solution for the front speaker.
Thansks
hi, and thank you for viewing,
when i connect my bluetooth headset my x1 wont ring anymore. it vibrates and rings through the earpiece but not outloud.
i dont wear the earpiece until i get a call as i find it uncomfortable so i get a lot of missed calls.
i have looked through the settings but must be missing somthing can anyone help me?
thank you for your time
never heard about any bluetooth able phone being to direct audio to a headset while still playing it out it's speaker
people seem to use the headset to save other people from ringning apart from the handsfree thing
thanks,
what i mean is i want the X1 TO ring as normal so i know someone is ringing,
at the mo i have a bluetooth earpiece and when someone calls, my X1 is silent and the ringtone is played through the earpiece.
as i dont wear the earpiece until i recieve a call due to comfort i miss many calls when im in the car.
im sure it never done this in R1A but not certain
It should normally ring...my phone and bluetooth both rings at the same time....may be goto bluetooth select the device and only keep a check on handsfree option....
well after updating to R3A the problem is now resolved.
Another one of those "dunno what it was but its working now" things
thank you for your help