Database Users

Attempt to fix my phone

First, my problem started with either updating to the new JFv1.43 recovery, or flashing the new SPL from Haykuro.
Symptoms:
1. Everytime I flash a new ROM, wipe or no wipe, I come back stuck at the T-Mobile G1 boot screen. The only way I've found to get through is to take out battery and boot into ADB (the Camera + Power screen) and "fastboot flash boot boot.img". This almost always work.
2. Nandroid stopped working. Nandroid always errors during the process of backing up, and I'd only have splash1.img and splash2.img in the nandroid folder of my SD card. Kind of want to try reflashing the JFv1.43, or even go back to 1.42 (can't find) for troubleshooting. Also not sure if this would affect the new SPL and cause a brick.
3. "Insufficient storage available" with Dude's and Cyanogen's builds. I'm not sure if this one is related to recovery or SPL. This might be caused by past attempts at doing apps2sd (I've done both symlink and unionfs).
Anyways, losing Nandroid has lost me a lot of time with trying out new ROM's, I'd really like to get it fixed. The boot stuck is a nuisance, but much less troublesome than losing Nandroid.

Its the SPL.

lbcoder said:
Its the SPL.
Click to expand...
Click to collapse
So then I'm stuck in this situation? Since the SPL can't be downgraded.

cigar3tte said:
So then I'm stuck in this situation? Since the SPL can't be downgraded.
Click to expand...
Click to collapse
I'm not positive (***so dont do this without researching***) but i think it would be possible to flash to a different one ( i mean, you flashed another SPL over the original one, right? ).
There is a "mega-thread" that has information on all the SPL's and their features/updates. If the info is anywhere, it's prob in there. Search in the Dev forum.

tr.slate said:
I'm not positive (***so dont do this without researching***) but i think it would be possible to flash to a different one ( i mean, you flashed another SPL over the original one, right? ).
There is a "mega-thread" that has information on all the SPL's and their features/updates. If the info is anywhere, it's prob in there. Search in the Dev forum.
Click to expand...
Click to collapse
As far as I can remember, that is where I read that you can't flash the older SPL over the new one.

cigar3tte said:
as far as i can remember, that is where i read that you can't flash the older spl over the new one.
Click to expand...
Click to collapse
damn the man!

cigar3tte said:
As far as I can remember, that is where I read that you can't flash the older SPL over the new one.
Click to expand...
Click to collapse
I could be wrong, but the key is not flashing an older RADIO with the newer spl.
You should still be able to go back to hardspl with no issues.

cigar3tte said:
As far as I can remember, that is where I read that you can't flash the older SPL over the new one.
Click to expand...
Click to collapse
I have flashed from the New H SPL to the HardSPL i originally had on the phone when I found out people were having trouble with the SPL. I install the NEW SPL again to run Hero, but you CAN flash it back to the older SPL I would recomend HARDSPL though.
*not responsible if this doesn't work but I was able to do this without any trouble. Was just a bit nerve racking.

i am 99% sure the above post is correct, don't flash a different radio, but you can flash another SPL right over the Haykuro SPL. i would double check that as there is a 1% chance it will totally screw your phone and i don't wanna be the guy that told you to do something that bricked your phone, but it should work. just to be safe you should make sure splash1 is the t-mo g1 screen so if it stops you can call t-mo

i flashed from the latest haykuro spl 1.33.2005 , to the original t-mobile spl HBOOT-0.95.0000. I fastbooted and it was showing the original spl installed.

Cannot boot after radio and spl update

After updating radio and spl my phone is stuck on the "T.. Mobile" "G1" boot screen.
Any help available? can I access the sd card without booting?

What SPL?
Ten characters...

sjbayer3 said:
After updating radio and spl my phone is stuck on the "T.. Mobile" "G1" boot screen.
Any help available? can I access the sd card without booting?
Click to expand...
Click to collapse
Was it haykuro's SPL? Can you get in to recovery (power+home) or the bootloader (power+camera)?

if it's haykuro's spl...
Hopefully, you READ & FOLLOWED the directions and flashed the RADIO first, then flashed the SPL. If you did not, then your phone is bricked.

if u cn get into recovery reflash ur rom. and like everyone else says hope u flashed the radio 1st

I did the radio first
I was able to boot into recovery, i tried a wipe and a few things but couldnt get it.
Eventually I got it by reflashing cyanogenmod.

sjbayer3 said:
I did the radio first
I was able to boot into recovery, i tried a wipe and a few things but couldnt get it.
Eventually I got it by reflashing cyanogenmod.
Click to expand...
Click to collapse
The SPL wipes the ROM, so after flashing the SPL you would need to reflash >.>

AdrianK said:
The SPL wipes the ROM, so after flashing the SPL you would need to reflash >.>
Click to expand...
Click to collapse
This may sound like a silly question but please forgive me as I have not yet flashed the haykuro spl.
Once you've flashed the new spl, instead of flashing the update.zip of the cyanogen rom, can't you use nandroid restore? Or will that restore the previous spl as well (in my case HARD SPL)?
I ask because I would like to try the spl, but I'm so comfortable with my rom and settings that I would hate to wipe just to try Hero which is still in development. Call me crazy, but I like stable and finished builds. But I am curious and with a lot of time on my hands but not so much that I'm willing to lose everything just to try something that I'm not going to keep.

Binary100100 said:
This may sound like a silly question but please forgive me as I have not yet flashed the haykuro spl.
Once you've flashed the new spl, instead of flashing the update.zip of the cyanogen rom, can't you use nandroid restore? Or will that restore the previous spl as well (in my case HARD SPL)?
I ask because I would like to try the spl, but I'm so comfortable with my rom and settings that I would hate to wipe just to try Hero which is still in development. Call me crazy, but I like stable and finished builds. But I am curious and with a lot of time on my hands but not so much that I'm willing to lose everything just to try something that I'm not going to keep.
Click to expand...
Click to collapse
I'm not actually sure about using nandroid after the SPL flash, but I'm certain that nandroid doesn't copy your SPL (I could be wrong). It would make sense for it to work.

i update inly spl from 1.33.0009 to 1.33.1000 and when its boot greeze in vodafone logo
what happend?
thnks

sjbayer3 said:
After updating radio and spl my phone is stuck on the "T.. Mobile" "G1" boot screen.
Any help available? can I access the sd card without booting?
Click to expand...
Click to collapse
I HAd The Same Issue, BUT YOU DIDNT BRICK YOUR PHONE all YOu Need To Do Is Flash The Rom , Thats The Resone Its Stayin On The Boot Screen Because Of No ROm Installed So Go Into Recovery >connect Your phone> choose usb toggle in recovery> (if on your pc you need a drivers, try putting the sdcard iin a next phone and connect it to the cpu> drag your rom to your sdcard (ROOT NOT IN A FOLDER) and flash it wen it boot first its gonna take long but dont worry it would come on :good:
If I Helped You In Anyway Thank Me Plzz
If You Still having problems just reply to my post

Radio update problem...

Hello,
I have a problem with my G1.
I got my G1 maybe a month ago. It had firmware 1.1 and radio module 1.22.12.29. Back then I did not realize it was a radio image compatible with firmware 1.0 as far as I gather from the HTC website.
At first, I did not intend to root it at all, a decision later I would regret. Well, it worked OK, only it was not updated. I was told I would receive the update over-the-air in 4 days. At first they said it would be to 1.5, but it turned out my operator started to upgrade straight to 1.6.
And so I did receive it in 4 days and the problems began.
Basically, the voice quality is so bad that half of what I say is ununderstandable. My voice sounds metalic and I cannot have a coherent conversation over the phone. It is a business phone, so you can imagine it is rather annoying when I have to struggle to be understood by clients.
Ok, so I checked the bootloader for the radio image version and I found out it was still version 1.22.12.29. As per the HTC website I should have 2.22.19.26I. So, obviously the radio firmware was not updated as it should be as per the HTC website. Thus, it seems the reason voice quality is so poor is the outdated radio firmware.
Since I did not plan to return my new phone to my operator (I had no time for it), I decided to root the phone and update the radio firmware myself. It seemed simple enough and I use Unix and Linux since 15 years, so it seemed it would pose no problem.
Quickly I learned that rooting 1.6 is not so simple. One-click method fails. Only goldcard worked and after a few days of struggle I finally got back to firmware RC7 and rooted the device.
Right after I updated the recovery image to CM 1.4, but before I flashed the CM ROM I attempted to update the radio firmware as was suggested by one tutorial I followed as well as the CM website.
Well, it all went smooth. After the update I pressed Home and Back, it rebooted, back to recovery CM1.4, one more time Home and Back and I was back to the working phone. I checked the radio firmware and lo and behold, it was still version 1.22.12.29. No errors, nothing, smooth update process and no result. I repeated it at least 5 times to no avail.
I decided to install CM 4.2.7.1 ROM and try to update the radio then. Before the CM ROM I updated the SPL to HardSPL with success to have fastboot and went to install CM. It went smooth and I booted into this new rooted G1 ROM with ease.
Again, I attempted to update the radio firmware from recovery CM1.4 and again no results.
So, I am back to square one. I have again firmware 1.6 only from CM instead of stock HTC, and I cannot use this phone for calling.
So, summarizing, I got the phone with firmware 1.1, but radio firmware from 1.0. Why it was not updated together with the system I do not know. Then I got an update to 1.6 and the radio firmware also did not upgrade. Then I went back to RC7 (firmware 1.0), rooted the phone, attempted the radio firmware update before installing CM ROM and failed. And finally, I installed HardSPL + HTC 1.6 recovery (as suggested on the CM website) + CM ROM and again failed to update the radio firmware to 2.22.19.26I. The update process is going without any errors. Verification, extracting, installation of radio image all go OK, the phone reboots but no radio updated.
Anybody any idea why it is like this? Why this phone refuses to update the radio from HTC website.
Any suggestions?
Oliwer
PS. One more thing, I was contemplating updating the radio via fastboot, but it seems after reading HTC website that fastboot is only for system and recovery image flashing. The radio has to go first adn from recovery console. Am I right on this?

I too have a problem updating to the 26i version. however i rooted at 1.5 using the one click root method and ive since switched from cyan 1.4 recovery and cyan roms to amon recovery and dwang roms. No matter which recovery i use, the 26 update flashes without an error but shows up as the same radio ive had all along (1.22.14.11) i made a thread about it but noone seems to have an answer. Sorry I couldnt help, but at least bumped up your thread and maybe someone can help us.

speedysilwady said:
I too have a problem updating to the 26i version. however i rooted at 1.5 using the one click root method and ive since switched from cyan 1.4 recovery and cyan roms to amon recovery and dwang roms. No matter which recovery i use, the 26 update flashes without an error but shows up as the same radio ive had all along (1.22.14.11) i made a thread about it but noone seems to have an answer. Sorry I couldnt help, but at least bumped up your thread and maybe someone can help us.
Click to expand...
Click to collapse
Thanks for sharing!
At least I know I am not alone here with this problem.
Since it's Christmas and I have some more time, I decided to do a Nandroid backup and wipe my phone back to the original rom with 1.0 firmware (RC7).
I used my goldcard and I flashed it in a few minutes. I logged back into 1.0 firmware with the original bootloader and recovery console.
Next I put everything on my goldcard, flashed the recovery CM1.4 from the terminal, went to the bootloader, flashed update.zip with the newest radio 2.x from HTC, everything went smooth. Reboot and again NO change of the firmware. Tried a few more times flash the radio and HardSPL together to no avail. I restored my backup and found myself back to square one.
One think I noticed, and I wonder if you get the same, is that when I flash the radio, the phone reboots back to the recovery console and shows "Formating Cache..." message. It does not tell me anything like Please reboot, just this message. Meanwhile I can move the cursor up and down the recovery menu, so the phone has not hang up. It just sits at the recovery until I reboot it. Once I waited 30 minutes to see if it reboots itself and it does not. So, I press Home+Back and then it reboots fully and after loging in I check the radio and NO change.
So, I wonder if your phone does the same?
Oliwer
PS.
T-Mobile G1 - w/ ROOT
DREA110 PVT 32B
HardSPL 10.95.3000
Recovery image: HTC Android 1.6 (from HTC website)
Class IV 8GB SD Card w/ Ext 4 Partition and Swap partition

That's a huge wall of text, and it's Christmas so I'm a little merry
When flashing the radio image w/ Cy's recovery you must flash as an update.zip using alt-s, press whatever key you need to press to confirm and reboot using home+back. If you use flash any zip or use the trackball to reboot the radio image (or SPL) will not reboot in the required way to complete installation.

AdrianK said:
When flashing the radio image w/ Cy's recovery you must flash as an update.zip using alt-s, press whatever key you need to press to confirm and reboot using home+back. If you use flash any zip or use the trackball to reboot the radio image (or SPL) will not reboot in the required way to complete installation.
Click to expand...
Click to collapse
I tried all possible ways. Just a few minutes ago I went to CM1.4 recovery, used the update from update.zip, pressed Home+Back, rebooted back to recovery console, pressed Home+Back again, booted to CM4.2.10, punched the PIN code, checked the About Phone section and I am still with 1.22.x radio firmware.
This phone simply refuses to update the firmware in any known way.
So, my plan now is to un-root it back to the state I got it 2 months ago and return it to the operator and request upgrade of radio, since Donut with an old radio is basically useless. People simply do not understand half of what I say even if I speak slowly and quietly.
Cheers,
Oliwer

You have to press
Cam+power and it will show radio
....
In settings that radio has nothing to do with one installed...Do you know that the radio does?
It allows custom roms like cyan to be installed while keeping root access. The rom allows some tmo apps like account to still be used here in the states.

yes oliwer i get the same formatting cache message but nothing else happens. i tried in cyans recovery and amons recovery using only button shortcuts and not the trackball. i always named the radio update.zip, but still no luck. Im not sure if the 26i radio requires a certain version before it can upgrade, like maybe i have to upgrade to another radio before i can get to 26i? im not quite sure...ive run out of ideas on what to do. I dont have a warranty or anything on my g1. does the fact im using a donut rom on a cupcake radio have anything to do with it? if i had a cupcake rom and upgraded the radio to 26i from there would it work? i know these might sound like dumb ideas but im still relatively new to the scene and im running out of ideas as to why this is happening or why i cant solve it..

bump? anyone have a solution for us? or advice?
i just realized that i had android 1.1 with the 1.22.14.11 radio when i first got my phone, when t-mobile gave me the 1.5 update, i was still stuck on the same radio for some reason. After that I used the one click method to root and ive been on dwang donut rom ever since with the same dated radio...Ive tried using cyans recovery to flash and still no luck, no error, it says its updated but when i check the baseband or stock spl its still the same radio. I never went for a danger spl when i rooted because i was afraid to brick so i cant fastboot a radio update. I asked in another topic if it was possible to use the "flash_image" command in terminal to flash the radio but i dnt think itll work and i dont wanna risk it. If anyone has any advice or a possible solution please keep us updated.
Thank you!

Turn your phone off, hold the camera button down, and power on your phone.
What do you see?

each time before and after the flashing of the radio using cyans or amons recovery image id get the same rainbow screen saying
DREA100 PVT 32B
HBOOT-0.95.0000
CPLD-4
RADIO-1.22.14.11
Serial0
so im still stuck on the Android 1.1 radio.

speedysilwady said:
yes oliwer i get the same formatting cache message but nothing else happens. i tried in cyans recovery and amons recovery using only button shortcuts and not the trackball. i always named the radio update.zip, but still no luck. Im not sure if the 26i radio requires a certain version before it can upgrade, like maybe i have to upgrade to another radio before i can get to 26i? im not quite sure...ive run out of ideas on what to do. I dont have a warranty or anything on my g1. does the fact im using a donut rom on a cupcake radio have anything to do with it? if i had a cupcake rom and upgraded the radio to 26i from there would it work? i know these might sound like dumb ideas but im still relatively new to the scene and im running out of ideas as to why this is happening or why i cant solve it..
Click to expand...
Click to collapse
I do not know, really, why the radio refuses to upgrade. Since my last message I have read tons of posts on this issue and nearly ALL people can upgrade the radio firmware easily, just like the SPL. Somehow, I can upgrade the SPL to whatever I want, but not the radio. Very strange indeed and no luck so far.
Oliwer

speedysilwady said:
bump? anyone have a solution for us? or advice?
i just realized that i had android 1.1 with the 1.22.14.11 radio when i first got my phone, when t-mobile gave me the 1.5 update, i was still stuck on the same radio for some reason.
Click to expand...
Click to collapse
Exactly the same in my case. Except they upgraded straight to 1.6. Before the upgrade I have 1.1 firmaware and quality of voice was perfect. After the upgrade things went south.
speedysilwady said:
After that I used the one click method to root and ive been on dwang donut rom ever since with the same dated radio...Ive tried using cyans recovery to flash and still no luck, no error, it says its updated but when i check the baseband or stock spl its still the same radio.
Click to expand...
Click to collapse
Same thing with me.
speedysilwady said:
I never went for a danger spl when i rooted because i was afraid to brick so i cant fastboot a radio update.
Click to expand...
Click to collapse
Well, I installed HardSPL and it worked despite the old radio. HardSPL offers FASTBOOT and I use it at times. This is safe, at least for me.
speedysilwady said:
I asked in another topic if it was possible to use the "flash_image" command in terminal to flash the radio but i dnt think itll work and i dont wanna risk it.
Click to expand...
Click to collapse
Well, I did, but it does not work since flash_image updates partitions and G1 does not have radio partition. So, when you try to update the radio.img it tells you no radio partition. It is only possible for Roger G1 since it has radio partition unlike all other G1s and there you could upgrade the radio with flash_image.
speedysilwady said:
If anyone has any advice or a possible solution please keep us updated.
Thank you!
Click to expand...
Click to collapse
Yeap! I just practised how to un-root the phone straight to 1.6 with the original SPL and recovery and I was able to restore my phone to the state before rooting and I plan to give it back to my operator under warranty and ask to get this radio fixed. I will do it next week. I will report if the authorized service will be able to upgrade the radio.
Oliwer

[SOLVED] - HD2 Flirting with the Devil.....

Anyone need a building block?
My HD2 is a total brick. HSPled and flashed rom (Romeos by Monx). Rom installed properly but the device cant start. Even after hard reset the thing is stuck at hTC white screen! Turns out that I should have flashed compatible radio first; But I am learning this after the fact. Nobody told me so.
Now please tell me what to do before i do something stupid. How do I install a compatible radio on a comatose HD2. Can I flash radio from the bootloader? Do I have to downgrade the rom first? Or must I install from the Sd card.
Guys I think a massive depression is setting in.

boot to boot loader, flash the radio using customruu just like you did the rom. job done.

PlayStation said:
Anyone need a building block?
My HD2 is a total brick. HSPled and flashed rom (Romeos by Monx). Rom installed properly but the device cant start. Even after hard reset the thing is stuck at hTC white screen! Turns out that I should have flashed compatible radio first; But I am learning this after the fact. Nobody told me so.
Now please tell me what to do before i do something stupid. How do I install a compatible radio on a comatose HD2. Can I flash radio from the bootloader? Do I have to downgrade the rom first? Or must I install from the Sd card.
Guys I think a massive depression is setting in.
Click to expand...
Click to collapse
relax, nothing irreparable
go to bootloader mode - connect to usb - flash proper radio as you flashed rom - job done

samsamuel said:
boot to boot loader, flask the radio using customruu just like you did the rom. job done.
Click to expand...
Click to collapse
+1 on this.
Don't panic. Experienced the same behaviour with same ROM (and proper radio).
Enter the boot loader and reflash via USB or microSD (both ways worked for me).

l.o.l. yeah, if hspl on and you used customruu it's all fine.
Even if not, you can flash stock always with goldcard.
surprised that it did not say on the first page what radiorom was recommended/necessary. In fact most 2.xx based roms state the need for a 2.07 or 2.08 radio.

1) reset the phone
2) hold on to the volumn down button till the 3-coloured screen (that's bootloader)
3) flash the radio ROM via USB
4) reset

Solved
Problem solved!
Ha ha apparently the panic was as a result of a false alarm. I flashed a compatible radio from the bootloader and all is well now.
Thank you all for the tips. I just needed a true and tested method to resolve the matter. And by the way Romeos rom by Monx is the bomb - better than Windows Phone 13 Series!!!!
http://forum.xda-developers.com/showthread.php?t=631662

Issues with (re)flashing recovery

Hello all,
Here's what happened - I DL'd the app 'ROM Manager' from the Android Market, installed and allowed this app to be the recovery for my MT3g (non-Fender and non-headphone jack version).
Suffice it to say that the ROM Manager app jacked up my phone... none of their items worked for me. I uninstalled the ROM Manager and now when I tried to go to recovery mode (power + Home) I get nothing but stuck on the MT splash screen
My phone is rooted, originally ran the recovery-RA-dream-v1.6.2 recovery and am currently running a 2.1 ROM.
I have tried to redo the flashrec-1.1.3x and this does not work.
Where do I go from here? I'd like to be able to partition my new 8GB SD card and I can't even do that...
Thanks in advance.

If your phone is rooted, can't you just flash the previous working recovery via fastboot again?
-------------------------------------
Sent via the XDA Tapatalk App

You should be able to put the recovery image on your sd card and use the flash_image command from the terminal right? thats what i did

Mod. edit: not dev related, moved to general

twigster said:
If your phone is rooted, can't you just flash the previous working recovery via fastboot again?
-------------------------------------
Sent via the XDA Tapatalk App
Click to expand...
Click to collapse
Just to let you know, it is possible to root a mytouch without ever having installed an SPL that allows flashing though fastboot. I know from personal experience that the one-click flashrec method does this

adavis159 said:
Just to let you know, it is possible to root a mytouch without ever having installed an SPL that allows flashing though fastboot. I know from personal experience that the one-click flashrec method does this
Click to expand...
Click to collapse
I know, thats what I did as well.
But since then, till the date I changed to an engineering SPL, im pretty sure I have always done the subsequent changes to my recovery and spl using fastboot, even after starting with the 0010 SPL (which was at the time a problem SPL) and using flashrec to change the recovery before installing my first non stock rom, being cyanogen 4.x.x, still with the 0010 SPL.
I do know that it only became necessary for me to change my SPL when I wanted to try new radio ROMs (subsequently moved back, and took the chance to move to the 2010 engineering SPL) Before that I was actually too scared to change the SPL because of the brick threats.
I used the cursorsense rom thread instructions on how to change the radio and spl, and it worked great.
Maybe, so far, I have been lucky not to brick my phone. But I have always followed well documented threads on the dev section and so far so good, not excluding one or two times when I thought I had made a nice brick, but just persevered.
Fastboot is your friend, and so is XDA if you are nice to it and the good people who frequent it.
If you look through the threads, and in the development section, there are alot of areas where they give the commands necessary for a variety of actions, and peoples responses on whether it works.
I don't yet believe in the programs created to do everything for you, nothing against the devs, who are all great, just not quite happy enough with comments posted to try them out yet.
(I think my response was little longer than needed) ;-)

Thanks for the info guys...
Problem was I could not boot into fast boot - the recovery was not there.
What I ended up doing was unrooting then rerooting my phone, reloaded my ROM and went on from there...
That might have been the long way of doing things but it all worked out well.