So, I had a nightmare - was chatting on my phone, stumbled, dropped the thing dead on to concrete.
The screen now has cracks running across it from top to bottom and a few snowflake/spider web looking cracks in it.
Whilst I can still read the screen and amazingly the touch sensitivity hasn't been affected, I don't want a smashed up phone.
So to clarify - my phone works fine, it scrolls and picks up typing etc etc - it is totally useable but the glass screen that protects the LCD screen has been damaged pretty badly.
Can I just buy a new screen for it? Or will I need an entirely new phone?
Cheers
A search goes a long way...
http://forum.xda-developers.com/showthread.php?t=613954
Related
Hi,
The touch screen part of my universal has ground to halt to the point that it won't work.
There doesn't appear to be any cracking and I don't recall dropping it or sitting on it.
I work a fair bit outside and can get quite a bit of dust and dirt in my pockets and am wondering if it could be due to dirt getting into the connect on the hinge.
Has any one else come across problems with the hinge?
I'm reasonably adept with a screwdriver - are there any things to watch out for when disassembling to check it over?
Hi..
If u can open with the Universal guide posted in the forum then try clean ing the connectors on the Right and Left of the Clamp Shell part with Iso Propyl Alcohol.
Before opeining you can try pressing mildly with yr fingers, at all the forur corners..it can start working..else do the above...
Hi,
OK, the screen seems to be working OK this morning, however I seem to be getting a sort of ghost effect where it appears as though the phone icon and the volume icons are getting pressed resulting in the volume controls and the phone/flight mode popup appearing on screen.
I guess it is all down to dirty connections.
Do you have a link to the thread about dismantling the hinge, I can't seem to find it.
Thanks.
re isopropal alchol
only use 99% alchol to clean contacts anything below that can cause corrosion on printed circut boards and contacts.
any progress yet.
mine stopped working today too.
but when i took off my screen protector, it worked for a while.. now its dead again.
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
being in Australia I go to the beach allot. with my jasjar.
the sand gets stuck in the sides of the screen putting pressure on the screen and disabling any input. just a thought that it could be the same with u.
hope u sort it out, otherwise claim it on warrenty sooner than later.
The problem I have with the screen is that occasionally the touch screen side of things appears to stop working and also the the volume, wifi and phone dialogs keep on appearing as if I am pressing the relevant icons in the top bar.
I'm guessing some dirt has got into it somewhere or there is a loose connection, but am struggling to open up the screen's case to inspect it.
6680abhi said:
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
Click to expand...
Click to collapse
i took off my screen protector and it worked an hour...
got home, prepared to go to the T-mobile store.. then cleaned my screen ( without protector ) with a small cloth and it was working again.. so weird..
lets wait and see what happens ..
It's not really that weird: If some dust, or something equally small gets between the screen and the plastic frame, it can put enough pressure on the screen, and so the touch screen takes it as a constant (or intermitent) input, invalidating any other action on the rest of the screen.
I just received my Aquapac waterproof (and sand/dustproof) to use my Jasjar hapilly in the beach! :lol:
oh so annoying, my volume sliders keep popping up now..., as if some one keeps tapping, cause when not in Land scape mode when i open the "START" menu. it scrolls down, the same input/tap as wher the volume is in Landscape mode
There must be something wrong ... my screen still isnt working properly
one possible solution for touch screen not working
guys.... although I dont need to register onto this portal and it took me 15 minutes to register (fault of my own) but I got so much relieved with the solution that it deserved 15 minutes of my effort ;-) I hope it helps someone...just like it did help me....
I own a P835 Asus mobile and from past 2-3 days was having problems - start menu continuously appearing and my taps not getting recognized. Since yesterday my screen suddenly stopped responding to any taps or scrolls altogether.... buttons were working fine but not the screen..... i spoke to the facilities centre this morning and was about to take it to the shop but due to my laziness...didn;t go.....
Thanks guys.... what you mentioned above is very correct.... it was just a tiny molecule of dust that the screen was interpreting as my input and finally refusing all my taps..... I just cleaned the screen and the speaker side with the mere stylus n things started working.... thanks a lot.... more than laziness was this worry cause I just bought this piece a month before....
so people...before takin it to the shop....try this one too.....huhhh.....
Hi,
Recently ive repaired a HTC Universal, put it back together as best as i could.
Now when i do touch the screen with a stylus, the screen has funny colours behind it. It kind of like when you touch/ prod your Computer LCD. It only happens when theres pressure on the screen so its not really a huge problem. The touch screen is definately there cause when i tap the screen it responds (e.g i tap start and the menu pops down).
If its normal then i can take it, but if its not im complaining to the ebay seller.
This doesent happen when i put any form of pressure on my HTC magician LCD, so im curious.
Let me know what happens with your universal
Cheers,
Whitemoo.
This is not normal behaviour of any touchscreen device!!
hmmm... well i just looked at the broken lcd screen, and even though the LCD itself is shattered, the touch screen is in perfect nick.
I put pressure on the touch screen and couldnt see any of the symptoms i saw on my current LCD
You guys recon i should swap the touch screen over? either way im complaining to the sellers, DODGY.
whitemoo.
from my knowledge, im pretty sure its normal. it happens sometimes on my 9000 so yeahh....
So I removed the included screen protector since it had a deep scratch on it. I read on the forums that you don't need the protector and that it actually works better without it.
Well my experience has been the complete opposite. Ever since I removed the protector I'm ready to smash this bloody phone. It's next to impossible to use due to the humidity in my area or something. The SMALLEST amount of moisture on my finger tips or even in the air will cause the screen to go haywire and register touches all by itself. Apps will open by themselves...i can barely type anything as it keeps typing multiple characters on it's own or other silly stuff. If I wipe down the display it will work fine for the first little bit until it gets that tiny bit of moisture from my fingers on the screen again and it starts going haywire again. It's a hassle just to try and unlock the phone from the lock screen at times.
So is my phone defective or is just the suffering I must incur by living in a humid area. I can't use the phone like this so I guess I'll have to look at buying a new screen protector. But if this is not normal and is a fault in my hardware then i would like to return it and get a different phone. I didn't really have issues with the screen protector on.
Ive kept my screen protector on my phone, works fine until i have moisture or (rain drops) on the screen, then my phone doesnt respond and also misfunctions the position of where i touch on the screen not sure if this is normaly as its the rain drops on the screen..
Tested witht he iphone 4 in the rain and works brilliant, why doesnt the X10 do the same !! :/
duffy1807 said:
Ive kept my screen protector on my phone, works fine until i have moisture or (rain drops) on the screen, then my phone doesnt respond and also misfunctions the position of where i touch on the screen not sure if this is normaly as its the rain drops on the screen..
Tested witht he iphone 4 in the rain and works brilliant, why doesnt the X10 do the same !! :/
Click to expand...
Click to collapse
As you may know, those screens are capacitive displays, that means they're activated by sending (very) small amounts of electricity and are kinda "looking for a conductive material" in order to register an input.
The conductive material can be your finger, or something like... a raindrop or your screen, so that's why it thinks you're pressing that part of the screen...
Now it's even more obvious without the screen protector since it's directly on the screen.
As for why the iphone doesn't have issues with that, it does, but the screen being multitouch it's not as bad...
thanks for the info.good to know.
I didn't like the thick screen protector as my thumb/finger seemed to drag and not slide smoothly. I took it off and replaced it with a slightly thinner protector. I'm much happier with the feel now.
Angie
Sent from my X10i using XDA App
@smok3yjk - probably best if you do as Angelahp - get another screen protector on there.
Hi,
I just want to thank everyone on this site for the plethora of information that is available.
Here is a rather strange issue, that I did not see covered previously...
I purchased a used aria with a cracked digitizer off ebay for pretty cheap. I replaced the digitizer myself and all was good. I used the phone for about a week and dropped it. After that, the digitizer has been acting a bit flaky.
For instance, when it decides that it wants to annoy me, every input seems to register only on the middle of the screen. For instance, if I touch the top of the screen, the screen registers touches as though I was touching the screen in middle of the height. If I touch the bottom, it still registers the touch in the center of the screen.
I found that If I knock the phone against a table, along the edge, the problem goes away for a while. Then it crops up, again, randomly.
Anyone have this issue?
Thanks,
JC
well my htc hd2 is using android and using it a year by now and notice that the upper left of the screen is not working?is it the lcd or digitizer or just need to align it?i dropped this many times(up to 5 times i think)but no damage on the housing and it looks new,and it is annoying in some games cause it wont work and i notice a very little red dot on that part.....pls help
If you lost sensitivity and the screen does not respond to touch, then it's a digitizer, if picture is distorted or, as you describe, a red dot appeared where it shouldn't be - LCD, sounds like both in your case. I am not quite sure how it doesn't work in games or whether the problem is present in normal screens. Alignment is a procedure to tune and correct mistakes in touch recognition or to make touch more precise on resistive screens.
I suggest replacement of your LCD + DIGITIZER. Dropping it many times may have caused it too, even if housing looks perfect.