Hi there,
I have HUGE problem. I had used HPSL to install a official ROM that is NOT standard in my country. The ROM installed ok but on the startup screen with the windows logo the white bar at the bottom just keeps filling up and restarting. And now I am unable to use my device. Any help would be appreciated.
Regards
Delta-XVI said:
Hi there,
I have HUGE problem. I had used HPSL to install a official ROM that is NOT standard in my country. The ROM installed ok but on the startup screen with the windows logo the white bar at the bottom just keeps filling up and restarting. And now I am unable to use my device. Any help would be appreciated.
Regards
Click to expand...
Click to collapse
Have you tried a hard reset?
iang123 said:
Have you tried a hard reset?
Click to expand...
Click to collapse
Is that the little button on the back of the device? Or is it a combo of buttons?
Regards
Fixed! Did the button combo factory re-set all fixed!
Thanks
buttons
its a combo of buttons. hold down the volume up and down key at the same time and power the phone on. that should get you to a multi coloured boot screen. just follow the instructions from there to reset
ha ha. no problem
Related
Hi all,
I have dead JASJAR dead after ROM UPDATE.
I cannot enter bootloader menu.
Please any help
Thanx in advance
BR
Julian
If you don't mind explaining more detail on the step that you have done on flashing your universal, maybe someone can come up with some help.
bambacik said:
If you don't mind explaining more detail on the step that you have done on flashing your universal, maybe someone can come up with some help.
Click to expand...
Click to collapse
Here is little explanation about upgrade process;
I upload firs and second file and it was 100 % success, but when I upload the third file in the middle something happen and message appears " restart your device" or somethink similar.
After that device dies, I try all combinations for HARD RESET and BOOTLOADER menu but without success.
Please any HELP
BR
Julian
Press camera+power and soft reset and check if it get into bootloader where u serial top.
hdubli said:
Press camera+power and soft reset and check if it get into bootloader where u serial top.
Click to expand...
Click to collapse
not working this combination any other ideas ?
Thanx in advance
Not camera+power+reset, but backlight+power+reset.
bambacik said:
Not camera+power+reset, but backlight+power+reset.
Click to expand...
Click to collapse
Same ... I tryed all the combinations to enter bootloader, but... no success
BatRambo said:
Hi all,
I have dead JASJAR dead after ROM UPDATE.
I cannot enter bootloader menu.
Please any help
Thanx in advance
BR
Julian
Click to expand...
Click to collapse
A) Plug your phone into your computer via USB.
B) Press the Power and the light button, not the camera.
You should see a faint outline that says USB.
It's now recognized in the Device Manager, run your ROM Update and fix it now.
Where is the "light" buttom? Please.
BatRambo said:
Hi all,
I have dead JASJAR dead after ROM UPDATE.
I cannot enter bootloader menu.
Please any help
Thanx in advance
BR
Julian
Click to expand...
Click to collapse
I had the same problem b4:
try this:
1) plug the usb cable in 1st
2) soft reset the imate (the screen should have a very light "USB" word)
3) run the rom update on the PC
4) after completion, hard reset (press the 2 "-" buttons on the imate) and press the soft reset bottun together.
5) when the screen is re-set, press "X" to exit instead of "0" to go to factory default.
still no solution
only jtag solution can turn on the phone
and i think its possible only in service center
sorry for the caps.
btw hello everyone
well lets just get to my problem.
i installed the touch it program rom thingy or whatever to my phone
and now im trying to restore it back to its original settings...
the only reason im doing that is because i cant connect the phone to the usb anymore. it WONT connect.
so im trying to restore it.
please help!
thanks!
or can someone just tell me how to reconnect it to my computer please?
i've tried different ports on the computer
and restarted it
but nothing, so please help me restore to factory settings or be able to use windows mobile device center
thanks!
maybe activesync didn't install properly when you flashed it..
or.. you should try the activesync uninstall/reinstall trick..
or a corrupt system file and you just have to hard reset the phone..
hmm..... good question
hard reset is when you press the clear storage right? or when u take out the battery while its still running??
well even if those arent hard resets i've tried them and none work
=[
A hard reset is preformed as follows:
-Hold down the two softkeys on the front of the device (the ones above the Windows logo and the OK button)
-Press the reset button using the stylus, which you can find below the volume adjuster on the left hand side of the device
-Release the stylus, but keep the softkeys held down
-You will see a warning screen
-Press the green send key on the left - the one with the phone icon on it to confirm the reset.
After that it will take a little while longer to start up the phone.
Btw if you by "original settings" mean restoring your official ROM a hard reset won´t do. You will need to flash the official ROM to go back if I´m not mistaken.
thanks for the info!
hey again
well im trying to restore the original rom but everytime i do it wont go past 1%
then touchit starts up.
help me please! i dont want touchit on my phone anymore
goodtilltomorrow said:
hey again
well im trying to restore the original rom but everytime i do it wont go past 1%
then touchit starts up.
help me please! i dont want touchit on my phone anymore
Click to expand...
Click to collapse
Did you hardSPL? What SPL / IPL version is shown on the multicolor screen?
knrubar said:
Did you hardSPL? What SPL / IPL version is shown on the multicolor screen?
Click to expand...
Click to collapse
Are you just trying to go back to the stock ROM becasue of the AS problem? Did you try a reinstall? After you uninstall before reinstalling AS go into your program files on the PC and delete the activesync folder.
If you HARDSPL'ed you need a STOCK ROM without the nbh. file. Thats why its kicking back to TOUCH.
Good Luck
Hi,
For the last month I noticed that Left softkey (Phone softkey) is freezing.. Now this is becoming more often. The only solution I found is when it freezes to press windows start button at the top left corner and then the phone is working normaly again. At the moment I press left softkey and it freezes, I see that background for that button drops in (the animation works). Then, to un-freeze it, I press verry gently with stylus windows start button.. The rom upgrade didnt work, so I dont know if this is hardware or software bug ???
Any idea ??
dgdragon said:
Hi,
For the last month I noticed that Left softkey (Phone softkey) is freezing.. Now this is becoming more often. The only solution I found is when it freezes to press windows start button at the top left corner and then the phone is working normaly again. At the moment I press left softkey and it freezes, I see that background for that button drops in (the animation works). Then, to un-freeze it, I press verry gently with stylus windows start button.. The rom upgrade didnt work, so I dont know if this is hardware or software bug ???
Any idea ??
Click to expand...
Click to collapse
It sounds like a firmware issue, especially since you had attempted to upgrade the ROM version and failed to do so. Have you tried performing a hard reset? This will restore the phone back to default factory settings and should resolve this problem.
I would strongly advise you to first backup your data (Contacts, Emails, SMS, etc) using PIMBackup.
To perform a hard reset, please try the following:
(1) With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
(2) Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.
(3) Release the VOLUME UP and VOLUME DOWN buttons, press the VOLUME UP button to perform the hard reset.
Regards.
p.s. if you would like some detailed information on how to unlock your phone to upgrade to another ROM version, such as a custom ROM, then please carefully read the following guide.
Mastoid said:
It sounds like a firmware issue, especially since you had attempted to upgrade the ROM version and failed to do so.
Click to expand...
Click to collapse
Hi again,
Thanks for your replay. I succeded with ROM upgrade. The problem appeared while I was using previous ROM version (some clean WWE) and then I flashed to custom ROM few days ago thinking that I had a lot of programes instaled on previos ROM and if I install a clean ROM problem will dissapear.. Now I see I was wrong.. I dont realy get it.
I was following the guide from your post while I was upgrading the ROM I have now. And when I did, I did hard reset..
Good thing is that I found the temporary solution how to unbug it (by pressing start button) otherwise I would be verry pissed of as I dont have warranty
Did enyone experienced same problem ?
dgdragon said:
Hi again,
Thanks for your replay. I succeded with ROM upgrade. The problem appeared while I was using previous ROM version (some clean WWE) and then I flashed to custom ROM few days ago thinking that I had a lot of programes instaled on previos ROM and if I install a clean ROM problem will dissapear.. Now I see I was wrong.. I dont realy get it.
I was following the guide from your post while I was upgrading the ROM I have now. And when I did, I did hard reset..
Good thing is that I found the temporary solution how to unbug it (by pressing start button) otherwise I would be verry pissed of as I dont have warranty
Did enyone experienced same problem ?
Click to expand...
Click to collapse
Personally, I haven't ever experienced this problem, but it's good to know all is well now
Best Regards.
The issue is happening to me too.. not sure why..
Hi guys
My menu button on my homescreen now does nothing..
It used to bring up - change wallpaper, etc. Now it does nothing..
Does anyone know what i need to assign to it to bring back the old pop up menu?
I have searched but no luck!
thanks
cd78 said:
Hi guys
My menu button on my homescreen now does nothing..
It used to bring up - change wallpaper, etc. Now it does nothing..
Does anyone know what i need to assign to it to bring back the old pop up menu?
I have searched but no luck!
thanks
Click to expand...
Click to collapse
Did you install anything recently after which your menu button does not work anymore? If yes, deinstall it and see if its working again. If no, either you have to do a soft or hard reset.
regards, Kuzibri
kuzibri said:
Did you install anything recently after which your menu button does not work anymore? If yes, deinstall it and see if its working again. If no, either you have to do a soft or hard reset.
regards, Kuzibri
Click to expand...
Click to collapse
I installed a theme - soft reset didnt work.
Flashed a different ROM to start afresh!
thanks for your reply though!
cd78 said:
I installed a theme - soft reset didnt work.
Flashed a different ROM to start afresh!
thanks for your reply though!
Click to expand...
Click to collapse
Probably that was the problem. New theme and not working soft reset. Does the menu work now after different ROM?
I desperately need an alternative way to hard reset my hd2. Holding the up down button and shortly pressing the on/off button just switches the phone on. No reset. btw I cant start up normally so the software approach doesn't wort either.
Peter65nl said:
I desperately need an alternative way to hard reset my hd2. Holding the up down button and shortly pressing the on/off button just switches the phone on. No reset. btw I cant start up normally so the software approach doesn't wort either.
Click to expand...
Click to collapse
Use the reset button on back whilst holding up/down buttons
a few people have commented on the difficulty of getting both up and down pressed correctly.
I find I get a much better press with the battery cover off, and I press one first, then the second.that way you can feel them connect individually.
Why don't you guys use the build in software to hard re-set the devise.
1] Press Star Icon
2] Press Setting Icon
3] Press System Icon
4] Press Clear Storage Icon
That should start a hard re-set on device and re-store everything back to original configuration.
maniep said:
Why don't you guys use the build in software to hard re-set the devise.
1] Press Star Icon
2] Press Setting Icon
3] Press System Icon
4] Press Clear Storage Icon
That should start a hard re-set on device and re-store everything back to original configuration.
Click to expand...
Click to collapse
why don't you read the opening first again?
the dude can't use the software approach because his windows won't start, remember?
what about using task 29 or the reflash original splash screen while its doing its thing you can use both hands to hold the vol buttons, other than anything else suggested i dont thinj there us another way to hard reset other than reinstalling your rom maybe fix the software wipe storage app.
That works!
11calcal said:
Use the reset button on back whilst holding up/down buttons
Click to expand...
Click to collapse
Thanks, finally got the thing going again.
I have the same exact problem. None of these methods are working for me. Is there anthing else I can do?
Same for me. Locked out of the phone completely. When it boots it only gets as far as the O2 start up screen and doesn't get any further. Hard and soft reset do nothing. Have tried all suggested here already.
When I get to the screen where I'm prompted to press Volume up to restore, it goes straight to 'restore completed' in a fraction of a second, then back to the start up screen when I press Volume up again.
Need help as I now have an HTC paperweight and no phone!
sonicuk said:
Same for me. Locked out of the phone completely. When it boots it only gets as far as the O2 start up screen and doesn't get any further. Hard and soft reset do nothing. Have tried all suggested here already.
When I get to the screen where I'm prompted to press Volume up to restore, it goes straight to 'restore completed' in a fraction of a second, then back to the start up screen when I press Volume up again.
Need help as I now have an HTC paperweight and no phone!
Click to expand...
Click to collapse
Been using magldr? Cos hard resetting with magldr installed just affects magldr, hence a very short reset time that does nothing.
samsamuel said:
Been using magldr? Cos hard resetting with magldr installed just affects magldr, hence a very short reset time that does nothing.
Click to expand...
Click to collapse
No, I don't even know what that is. I'm not very technical and all I had installed was Cookie's Home Tab Editor.
I have the same problem.
My HTC is blocked ( the WM "forgot" the password that I set - a common problem ), so I have to do a Hard Reset that doesn't start.
I can't reflash or do anything else ( as told here ) without instaling HSPL first. As this can only be installed by the Active Sync, and Active Sync doesn't connect to blocked phones, I can't do anything else...
Is there a way to do anything else with only a new ROM in the sd card ? Or I REALLY have to install HSPL first ?
Thanks,
Leo
leodino said:
Is there a way to do anything else with only a new ROM in the sd card ? Or I REALLY have to install HSPL first ?
Click to expand...
Click to collapse
It is possible to be stitched from a SD-card without reinsertion HSPL. It is desirable to stitch official ROM
It is desirable SD-card to format a feather an insertion.