Related
i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen. it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
any suggestions would be great, plz im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
EDIT: just for those coming to this ancient and recently revived thread, this (my) problem has been solved. altho there are other people now with similar problems
Have you tried re-flashing?
jim256 said:
i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen!! it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
can anybody help me???? PLZ im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
Click to expand...
Click to collapse
Do a camera power reset and try again.
i tried that and it didnt do anything at all. isnt that just where you hold the end key and the side camera key and stick the stylus into the hole?
if so, it have any different effect than the standard soft reset
AraqirG said:
Have you tried re-flashing?
Click to expand...
Click to collapse
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.
jim256 said:
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.
Click to expand...
Click to collapse
Hold down the power button and the camera button at the same time until the tri colored bootloader comes up. If that works, try flashing the stock rom for your carrier.
If that doesn't work try the same steps with the memory card removed.
If that doesn't work try to do a hard reset and see if that will take you to the bootloader.
Also, what are the numbers in on the bootloader...are you sure your device is unlocked? I believe it should say... SPL-00.40.coke... on the 2nd line if your unlocked.
You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.
sorry i wasnt saying i needed to connect to activesync to reboot, i was saying i needed to connect to activesync to flash, and it wouldnt boot up so i couldnt get to activesync.
and i did to imcokemans unlocker, and everything went fine. when i was setting up the device (ie. setting password, time zone, calibration, etc...) i just decided that i didnt need to finish that as i was intending on flashing a custom rom anyway, and so any settings i put up the time to set would be erased.
having said that, i went ahead and starting flashing a custom rom right from the wm welcome screen that you get on a first boot.
thanks a LOT for your help, promptness, and attention
So are you back up and running?
well, now i am. i just took a 30 min drive down to the sprint store and got a replacement :S
thanks a lot for your help though, im scared i may really need to refer back to this thread later. but if i do, at least i know i should be able to fix it!
thanks.
well, i just did it again. i must be doing something wrong in the cooking of my ROMs...about to try out your solution..hope it works!!
wish me luck :S :S :S :S
well i was able to re-flash, but, unfortunately, it is stuck in the same "htc smart mobility" screen again. i think i have been able to narrow it down to the oemizer app. i must be doing something wrong in there.
oemizer http://forum.ppcgeeks.com/showthread.php?p=100746&referrerid=10115
ill keep cooking and trying tonight until i find what it is the problem is i guess, thx for your help guys. especially you 360discgolf.
well, after cooking and flashing too many times to remember this late, all i can do is ask for help when you guys wake up and check this thread.
in the last couple of builds i havent been doing anything with oemizer at all and it still hasnt been working, and i dont think i am doing anything extra in buildos that i havent done before in successful ROM images...it seems sort of erratic.
any suggestions/hints/comments would be great, thanks a lot.
you can't just hold the two buttons and press the reset. You have to hold the two buttons at the same time, then while holding them, use the stylus to hold the reset until it restarts. If you just tap the reset button while hold, it doesn't work.
360discgolf said:
You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.
Click to expand...
Click to collapse
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!
vkolas said:
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!
Click to expand...
Click to collapse
what carrier are you?
EDIT: also:
1) what os version are you running? (build number)
2) what radio are you running?
3) what bootloader are you on? (can be accessed via holding power + camera button and poking reset hole)
4) what are the orange numbers in the very bottom right of the screen when you are booting up?
these kinds of things all need to kind of jive for the sleep function to work correctly
jim256 said:
i used imcokemans unlocker (which i have done before) ...
Click to expand...
Click to collapse
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.
denasqu said:
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.
Click to expand...
Click to collapse
haha sorry this is a problem that i had a VEERRRRY LONG time ago. have learned a lot since since then, now it is this other fella here we are trying to help him
thx tho!
Hi guys, you have been a great help to me so far, but I just can't find anythign to help me with this now. I have a hermes100 with WM6 and i just flashed the radio to 1.54.07 and it gave me an option for hardSPL and said that it was recommended so i investigated and found the upgrade for it.
I ran the wrapper file and it goes to the stage where it puts my hermes into flash mode but it displays "spl1.09" on the screen yet when push the ok and power keys during reset it shows "spl2.03"
it goes through the screens until it puts my phone into flash mode and it says it is trying to read my device then i get error code (260) that it isnt connected. Anyone know a way to fix this?
Use sd card method, page 116 on here: http://forum.xda-developers.com/showthread.php?t=296722
Hope this helps...Cheers...
okay, i tried the sd card method and it does the same thing. after it gets to the bootloader screen i just sits there with
"HERM100
IPL-SSPL by des
HERM 100
SPL-109.ds
serial"
okay, nevermind, i just had to reinstall the drivers for when i was in bootloader mode. I got it to work, thank you for you help.
cheers :-D
No problem, now you should be able to flash any hermes rom to your hearts content with the knowledge you have a safety net if something does(and probably will, as you'll find flashing addictive, sooner or later) go wrong. Pleae remember though that Hard SPL ISN'T a guarantee that you will be able to fix you phone, it just makes it easier when something goes wrong... Cheers....and happy flashing...
samterry1234 said:
okay, nevermind, i just had to reinstall the drivers for when i was in bootloader mode. I got it to work, thank you for you help.
cheers :-D
Click to expand...
Click to collapse
how did you do this?
I don't know if the phone is bricked or what. Was in the store tonight, tried to text message my wife who I couldn't find and the phone was all locked up.
Soft reset, and only the date/time loaded, nothing would run. Soft reset again, and the phone didn't load past the bright splash screen. Tried soft reseting a bunch more times, nada. Did a hard reset, first one didn't work. I think it was the 3rd hard reset that took. Phone seemed like it was back to basic WM5, would be okay. Went home, put it on the charger.
Went to take it off the charger to reload data, and it won't turn on. Soft reset, freezes at bright splash screen. Hard reset, same thing.
Is my phone bricked? Anything that I can do to revive it? Or am I SOL?
Cingy/ATT 8525 w/WM5
(By "bright splash screen" I mean when the splash screen flashes brightly. It increases brightness, but just stays that way.)
Any help greatly appreciated.
I managed to load the official WM6 ROM (spl 2.03) via the built-in bootloader. I have radio, ROM, and GSM. It boots through the ATT animation, then freezes. It leaves a black screen with a blue and green static bar running horizontally across the screen about 1/4" thick.
I don't know how to get Hard-SPL loaded on the device because the only way I can see the device is when it's in the built-in bootloader mode.
will attempt PB/KITL I guess, though I can't at this point get the phone to display the KITL info.
No KITL in the ATT WM6 ROM.
Managed to get ATT WM6 ROM through the setup, after the "customization (bloatware)" it reset, and now it sticks on the bootup animation.
So close, I have SSPL and Hard SPL on the micro SD, if only I could get to the damn file manager. If I could somehow cancel out the customization process grrr.
On power charger, I seem to be able to get through the setup after a hard reset okay. It just won't boot after the reset.
Any ideas. I gotta get a few hours sleep. Sorry if this dialog to myself is in the wrong area, I didn't notice the "bricked hermes" thread was in the upgrades, etc area.
viatorx said:
No KITL in the ATT WM6 ROM.
Managed to get ATT WM6 ROM through the setup, after the "customization (bloatware)" it reset, and now it sticks on the bootup animation.
So close, I have SSPL and Hard SPL on the micro SD, if only I could get to the damn file manager. If I could somehow cancel out the customization process grrr.
On power charger, I seem to be able to get through the setup after a hard reset okay. It just won't boot after the reset.
Any ideas. I gotta get a few hours sleep. Sorry if this dialog to myself is in the wrong area, I didn't notice the "bricked hermes" thread was in the upgrades, etc area.
Click to expand...
Click to collapse
Not sure I fully grasp what's happening here, but if you want to stop the customisation then hard reset and when it goes to the loading cusimisation stage shove the stylus in the hole to do a soft reset and it will stop it loading.
Mike
Alright, thanks, will give that a try.
I managed to run the official ATT WM6 ROM and flash it without a hiccup (twice), and task 28 in bootloader says no bad blocks. So I am confused how I can flash an "official" ROM successfully and the device still won't work. Am starting to suspect hardware failure apart from memory.
Thanks a million mate, that worked. Phone boots now, already have SSPL installed. Need to update .net and activesync for Hard-SPL 7 to run I guess. Then I have more options.
Woot! I unbricked my phone
Once I was able to hard reset and cancel the "customization" I ran SSPL, then Hard-SPL 7, then I Super-CIDed the device.
I haven't tweaked the data settings yet, but I can send/receive phone calls. Which is a coup, because this is my main line.
It runs sluggishly. I don't know if that is the ROM or the device. It won't boot if it's plugged into USB, and after flashing Hard-SPL it isn't a recognized device by windows, won't connect to activesync.
I am treating the phone gingerly right now, will try and unload the ATT wap settings cab and restore my pim.
At least now I have the option to install another ROM if it bricks on me again.
I really should have flashed Hard-SPL the DAY, the MINUTE after the warranty was up. Lesson learned.
Or not.
ATT ROM locked up on me, decided to try Schaps 4.40. Won't load past WinMo "tap screen to setup" screen. Guess I'll try something else.
For a stable WM6 rom try TNT SE. It is REALLY stable but does come with some 3rd party apps. Thought you might like to get it working though first then try the other roms and in my experiance I haven't found many other roms that were THIS stable...
Hope you get it working...
For a disassembly guide try this site - http://michael-channon.spaces.live.com/PersonalSpace.aspx?_c02_owner=1
Its a bloody good place to go for all things to do with hardware and Mike is a true guru with hardware problems...
Cheers...
Recently flashed to NSFfans 6.5 WM rom. I couldn't activate the phone on my account because it wouldn't take the ##...# codes.
Long story short I attempted flashing Bigstorage_SprintTouchRom.exe to try and get back to sprint software where I could use the ## codes.
Everything went smoothly until first boot when it stopped at the "HTC smart mobility" screen. I then hard reset it (send+end+reset button on bottom) and it is still locking up on that screen.
Did I just break my phone?
Thread moved to General.
No, you didn't brick it. It simply sounds like a bad flash.
Try flashing to another rom and see what happens. Which unlocker did you have on? 2.31 or .41?
BTW, if your ## codes don't work is probably because you are using a themed dialer. NFS' rom has a folder under Start Menu that is called "Phone Codes". In there, you will find the PST shortcut, which will allow you to program your phone.
if you can get into the bootloader (tri-color screen) then you haven't bricked it.
Sorry for posting in the wrong forum.
How can I get to the boot loader if the phone stays at the "HTC smart mobility" boot screen?
I tried using the rom update utility but it's not connected so it won't do anything.
---------------------------------------------
Edit: Okay, I have successfully re-flashed back to 6.5. The bootloader can be accessed by turning on the phone while pressing the camera button.
I am using 2.31 unlocker. When I try and activate the phone again what do I need to change in the phone codes to make it work?
Thanks guys.
Jacob_newton said:
Sorry for posting in the wrong forum.
How can I get to the boot loader if the phone stays at the "HTC smart mobility" boot screen?
I tried using the rom update utility but it's not connected so it won't do anything.
---------------------------------------------
Edit: Okay, I have successfully re-flashed back to 6.5. The bootloader can be accessed by turning on the phone while pressing the camera button.
I am using 2.31 unlocker. When I try and activate the phone again what do I need to change in the phone codes to make it work?
Thanks guys.
Click to expand...
Click to collapse
Under the PST programming, more than likely you will only need to change:
MSID
MIN
HOMESID
username and password (for internet)
You shouldn't need to mess with anything else afaik.
i cant make my phone go up normaly
i have the same problem and i tried to flash with others rom's with no succes ... my phone still locked in start screen . i dont know what to do.. i still can flash normally but i dont know wich rom will get back my phone again.. anyone help me plz!!
Osiii said:
i have the same problem and i tried to flash with others rom's with no succes ... my phone still locked in start screen . i dont know what to do.. i still can flash normally but i dont know wich rom will get back my phone again.. anyone help me plz!!
Click to expand...
Click to collapse
Details, details - how have you flashed? Have you tried flashing from bootloader? Flashing a carrier rom from bootloader should do the trick.
mrkite38 said:
Details, details - how have you flashed? Have you tried flashing from bootloader? Flashing a carrier rom from bootloader should do the trick.
Click to expand...
Click to collapse
Its ok already fix it... =) but i think i need to start over again from unlock to flash it with another rom!
Hi
A friend of mine has a HD2, never HSPL or anything and still running on 1.42 rom.... Now everytime it boots it goes straight into the bootloader. Since its never been messed around with I find it odd, seen it before with people with other phones. Would this just be a corrupted ROM and therefore it goes there, would if poss a stock rom flash be able to restore the phone, if that is not the case then a warranty return is still valid, but obv not wanted.
What do you think, will this work? I did search but everyone's posts come up with I task 29 and now stuck... etc and not from a stock bootloader as well!
Cheers any help will be appreciated, my first thing I will get him to try is a rom reflash but that will be tonight, I'll update on the progress then!
First thing I would check is if his volume button is stuck for some reason. Second would be to see if it detects a USB connection, then hard spl and new rom from that point. Keep us posted.
Sent from my GT-P1000 using XDA App
chris10230 said:
Hi
A friend of mine has a HD2, never HSPL or anything and still running on 1.42 rom.... Now everytime it boots it goes straight into the bootloader. Since its never been messed around with I find it odd, seen it before with people with other phones. Would this just be a corrupted ROM and therefore it goes there, would if poss a stock rom flash be able to restore the phone, if that is not the case then a warranty return is still valid, but obv not wanted.
What do you think, will this work? I did search but everyone's posts come up with I task 29 and now stuck... etc and not from a stock bootloader as well!
Cheers any help will be appreciated, my first thing I will get him to try is a rom reflash but that will be tonight, I'll update on the progress then!
Click to expand...
Click to collapse
The post above me is correct check and make sure the volume down button is not stuck/Hung in the down position. If it is stuck in the down position like it is being held down at boot then this is the cause of it going straight to bootloader at boot up. If there is no problem with the volume down button then try a hard reset of the HD2. Warning this will reset your friends HD2 tolike it was fresh out the box so any photos, videos, documents, and etc that is not on the SD card they will lose. Also any contacts that are not backed up withan app like Microsoft My Phone will be lost. To do the reset while the HD2 is off bold the volume up and the volume down buttons down and press and bold the power button down. When you see the tri color screen come up release the volume and power buttons and follow the instructions on the screen (hint: you will want to press the vume up button). Now if after the Hard reset your friends HD2 still goes to bootloader at boot up then download and flash the stock ROM for their HD2 you can find it on HTC.com but make sure you varifiy that it is for their HD2 by entering the serial number of their HD2 you can find the serial number look under the battery. To flash the ROM let the HD2 boot up to the bootloader and then connect it to the computer via USB cable and wait for the Serial in the white bar of the boooader screen to change to USB and for your computer to show it recognize the pbone and then run the .exe or RUU wich everone the ROM has.
Never thought of the key being held done will try that first.
Also I won't HSPL'ing as its in warranty and a half HSPL'ed phone is well useless
OK so i feel like a bit of an idiot for this one. Turns out what I call a bootloader and he does is totally different. For me Its the tri-colour screen, for him its the red/orange windows boot screen. So it was all solved by a HR. Great..
Sorry for those who offered the advice but it really was not needed. but solid advice it was, you always can rely on help in here