Hi, I've tried searching the forums, but i'm having no luck. I recently got the T-Mobile MDA (great phone, btw), and I was wondering if anyone can advise on how to enter numbers into your contacts, so that you can include a persons extension. This is a feature that I would like to know so that I can call friends and family at their work numbers, where I would have to call the company number, wait for the automated receptionist, and then dial the person's extension.
I use to be able to do this with a Samsung phone that I had for Verizon using a "p" pause feature, which would wait an additional 2 seconds per "p", followed by entering the persons extension. (ie, if you were to enter "(123) 456-789 ppppp 12345", the phone would dial (123) 456-789, wait 10 seconds (5p's = 5 x 2 seconds), then dial 12345.
if the above explanation was confusing, maybe you can check the info from samsumg's site at
http://erms.samsungusa.com/customer...D=557&PROD_SUB_ID=561&PROD_ID=613&AT_ID=24794
it gives an explanation of this "p" pause feature (not my previous phone, but still same feature).
overall, this would make my life easier when i use voice dialing, so that when i'm driving and want to call someone, i don't have to look down at my phone bad and try to touch the numbers (which are a bit inconvenient on the MDA), for the person's extension.
thanks for any advise you can offer.
Use a comma instead of "p"
i.e.
123 456-7899 ,,,,, 12345
thanks lotech, it worked. this will definitely save me from getting into a car accident.
Free program download
Hi there,
I have used this little gem of a program, it allows you to add numbers before and after the number you wish to dial. Very useful if you have a cheap international call contract from your mobile i.e. you have to dial a landline number which connects you. Hope this is of use to you all. keep up the good work site, Cheers.
Fergie.
Myprefixdial: http://www.freewareppc.com/communication/myprefixdial.shtml
Hi all,
I'm using the TyTN in Japan on NTT Docomo network.
I often have to calll abroad but unfortunately, Docomo has had the bad idea of not using the standard "+" symbol for international dialing. Instead, I have to dial a ridiculously long prefix number ('009130010') to access international before starting the number itself.
So far, I've been entering the full numbers including the prefix in my contacts but I still have lots of numbers with + to convert.
Also, if I'm abroad, since I'm on a different operator's network, I need to use the "+" and not the '009130010'...
Anybody would know a setting, or a hack or a software that would allow me to replace automatically '+' by '009130010' when dialing (including when I dial from a contact)?
Then I would just need to disable this when I travel abroad...
Thank you,
Thomas
www.thomashumeau.com
An application that does something similar...
http://www.hkscorpio.com/members/bong/product_MyPrefixDial.htm
Could you just change your area code in Outlook on your desktop before you leave and sync it up? Not sure whether it will do what you want but I guess it might?
Does any one know how to remove the "+" in front of the phone number?
For some of the contacts I want to use a different dialing prefix instead of the the default "+"; but every time I synz it with Outlook the "+" is back.
Thanks
normaly +XY is the country prefix all over the world
and even if one is calling from within ones own country it should not matter
if one use the country prefix
Sorry was traveling so could not get back to you on time.
Thanks for your suggestion I am aware of the +; but in Hong Kong there are many service providers who need you to dial their code instead of the + (as pluse is default to phone service company's network). So, e.g. +91201234456 would be to dial India using my network provider (CSL or PCCW); but there are other cheaper companies i.e. 1528, so instead I need to dial 152891201234456.
But, now the problem is ever time I remove the + and put this code for some of my contact(s) on my Dopod; Outlook puts it back and worst makes it default to 852 so after a synz I landup with +852152891201234456.
how to remove + in phone number
try photo cntact pro
there is option to remove + in incoming phone call
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
I have the same problem. Both calls and text messages.
I don't think it matters if the international code is there or not.
Really frustrating not knowing who calls.
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Hmm, I've changed the SIM, but I can't remember if it worked wih the first SIM card.
But a hard reset deletes everything, right?
There are a few things you have to be sure of:
Do not have double contacts, if you have a number (with and without operator/country prefix) twice in your list it will not show any name.
I don't know if this applies if you have a contact on your phone memory and on your sim card. I am sure it does have this problem if you have two contacts with the same number on the memory phone.
For some reason this is logic: On an incoming call, the phones checks it's phonebook and retrieves two numbers and then it does not know what to display, is it contact one, or two?
I hope this helps you out. I did not experience any problems (yet).
AndrewCZ said:
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Click to expand...
Click to collapse
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
samluke said:
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
Click to expand...
Click to collapse
Hi guys!! i had this problem too but i have fix the problem. what i do:
!) i store all my contacts in my sim card and delete the contacts in the phone.
2)do a hard reset
3)upon doing the hard reset, the phone will prompt you on importing sim contacts and finding your service provider. select both and and press ok
4)now try to call from your house to your phone to do a check.
5)my problem was solved after this
hope it helps!
KraFT_mk said:
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
Click to expand...
Click to collapse
What was happening to me before the reset was a bit different - the phone wasn't able to match anything at all - even a number called from the phonebook and stored in "recent calls" in EXACTLY the same way it's in contact, didn't match to the contact when redialed.
I think that something required for Caller ID to work gets done when the phone is first initialized, and that this step requires full access to the phone module (which the phone doesn't have without a SIM inserted and a proper PIN entered).
hi,
i encountered also that worry,
i set the HKCU\Control Panel\Phone\CalIidMatch value:9
my mobile phone number to test was stored as "06xxyyzzww"
and when i phone my diamond2 from that number
the caller id is recognized
(with showing as +336wwxxyyzz)
i tested from my home phone stored in contacts as 04wwxxyyzz
i rang my topaz its was identfied as my home,
(with showing as +334wwxxyyzz)
i am in france, + is for 00 ,our phone numbers are 10 digits long
(mobiles and "home") ,
to be joined from abroad, you have to dial +33+phone number WITHOUT the first digit "0")
so the "9" value i put in the registry
if it could help you
regards
Hi,
just stumbled over the same problem.
The old phone (HTC P330) resolved numbers from my used format 01234-56789.
Since my contacts are a mess, I have 01234-12345, +49-123456-456, +49 (0123)-456 and so on, it would be a great pain in my ass to switch every contact to +49123-456 (which the new phone resolved).
I compared the Registry-Entry from the P3300 with the TD2 and voila: TD2 was 12, P3300 had the value 8.
I changed the TD2 to value 8, reboot and now I'm happy again, the phone is getting used to my contact list
Regards
Heiko
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Caller ID problem, my solution
I had the same problem. But after a hard reset it seems to work just fine now. Remember to backup your downloaded programs etc before doing this.
Tyven said:
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Click to expand...
Click to collapse
Hi,
"8" should be the good figure for you, as in France
we have phone numbers +33987654321
and "9" is the good value for me, in:
HKCU\Control Panel\Phone\CalIidMatch value:
Edit: i remove previous "edit"
in fact all my contacts had been erased" so it was normal to have no caller ID?
ps: is your carrier sendind all the figures when you're receiving calls, i mean +4512345678
so perhaps you're encountering a bug .
you should try to backup your device, with a soft like spritebackup(special price for htc owners on their webpage) and experiment an hardreset
and restore
regards
Hi ,
did you ever try to change the following:
RegistryEdit and Decreasing the CallIDMatch from 12 to 7 solved my Issue
See below
HKEY_CURRENT_USER\ControlPanel\Phone" name="CallIDMatch"
Greetings from Slovenia
Hello,
that is my first post so please do not be very critical to my english level and PPC skills .
now this is an old thread but for BULGARIA the correct registry value is "9". Here the mobil numbers are as follows "08xx 123456" (9 digits without the ZERO at the very beginning). that is why the usefull number is that (default for my TD2 was 8). Now after this fix the phone can correctly identify which number i want to dial when i am inserting it by digits, instead of selecting the exact person. i do not know am i explaining correctly but i will try to put some more detail on that. When i want to dial some particular number (for example "08xx 123456") the phone select me the correct contact no matter how i put this contact in memory. with "+3598xx 123456" or only with "08xx 123456". before that intervention the phone identifies me the correct contact only if i type the digits, exactly the same way that i have added it to the memory. So i think that this registry key does not have a universal resolution. the resolution depends on how many digits is using tha particular mobile operator.
i hope that will be helpful for someone who is happy to own an HTC and is happy with it ... like Me
Hello,
I often use an access code to dial internationally, and once I am connected to that access number, I have to enter the number of the person I am calling.
I have an HTC Touch HD with WM6.1pro and cannot find a way to do it. If I connect to the access number, then at the prompt go to my address book and dial a second number, it assumes I want to have two separate calls and puts the access code on Hold... which is not what I want! I do not remember all my friend's numbers, so I do have to use the address book.
With my old nokia n95, once connected I could go to the menu and say I want to dial a DTMF which is the tone you hear when dialing a normal phone. This allows me to follow on with calling the number I need while connected to the call.
Is there a way of doing this on WM6?
I have a kind of work around. I edit my international friends phone numbers as a "car phone" and the numbers look like this
02081802828 p 0027115555555
the access code, then I add p to pause then their number.
The HUGE problem is that when I dial any of my international contacts, the phone displays the same person... so no matter who I call internationally, it always shows a photo of my friend Ian, and displays his name instead of the person I am actually speaking to. I think this is a bug where WM6.1 only looks at the first 11 characters of a number, but the problem is, all my intl numbers have the same first 11 numbers.
Help MUCH appreciated, thanks,
Mark.
livegod said:
Hello,
I often use an access code to dial internationally, and once I am connected to that access number, I have to enter the number of the person I am calling.
I have an HTC Touch HD with WM6.1pro and cannot find a way to do it. If I connect to the access number, then at the prompt go to my address book and dial a second number, it assumes I want to have two separate calls and puts the access code on Hold... which is not what I want! I do not remember all my friend's numbers, so I do have to use the address book.
With my old nokia n95, once connected I could go to the menu and say I want to dial a DTMF which is the tone you hear when dialing a normal phone. This allows me to follow on with calling the number I need while connected to the call.
Is there a way of doing this on WM6?
I have a kind of work around. I edit my international friends phone numbers as a "car phone" and the numbers look like this
02081802828 p 0027115555555
the access code, then I add p to pause then their number.
The HUGE problem is that when I dial any of my international contacts, the phone displays the same person... so no matter who I call internationally, it always shows a photo of my friend Ian, and displays his name instead of the person I am actually speaking to. I think this is a bug where WM6.1 only looks at the first 11 characters of a number, but the problem is, all my intl numbers have the same first 11 numbers.
Help MUCH appreciated, thanks,
Mark.
Click to expand...
Click to collapse
Don't know if it will work... but you coud try (using Advanced Config) to increase the number of digits used to "match" the numbers in the contacts... for example to 18 or 19 numbers... but I cannot immagine what other "consequencies"could happen...
Let us know !
Regards,
K
Hi Kostas
It seems that the problem is actually with spb Mobile Shell and not windows mobile.
When I dial using the windows mobile dialler, it gets the name and picture right, but when I use spb's dialler it shows the wrong person and name...
I will chase it up with them... and thanks for the good idea, unfortunately the Call ID Match does not help the problem.
Efgaristo!
Mark.