I want to customize the LED for status of signal (green if available, orange if non signal), for missed calls or missed SMS.
Any have the solution?
Not yet, but I have noticed that there are actually two light 'bars' one on each side of the ear piece, I am looking into it.
Bupahs said:
Not yet, but I have noticed that there are actually two light 'bars' one on each side of the ear piece, I am looking into it.
Click to expand...
Click to collapse
yes sir.
it should be : [light] speaker [light]
Bupahs said:
Not yet, but I have noticed that there are actually two light 'bars' one on each side of the ear piece, I am looking into it.
Click to expand...
Click to collapse
SoCalSpecialist said:
yes sir.
it should be : [light] speaker [light]
Click to expand...
Click to collapse
The right hand 'light' isn't the light you might think
It's a light sensor which measures the light conditions where the keyboard will be turned on when it's too dark...
so it's not a light, but a SENSOR
greetzz
Pietje_1985 said:
The right hand 'light' isn't the light you might think
It's a light sensor which measures the light conditions where the keyboard will be turned on when it's too dark...
so it's not a light, but a SENSOR
greetzz
Click to expand...
Click to collapse
yeah, I figured that out lol, had to get a hold of a spec sheet but its not a light, it is the sensor
Hello, are there some news for the LED?
I own the European Version of the Maple (Snap)
and the indicator LED stops flashing after 10minutes, even if i
have not read my messages/missed calls.
I want the LED to flash until i take care...is there a way?
thnx in advance,
RB
Randel Burton said:
Hello, are there some news for the LED?
I own the European Version of the Maple (Snap)
and the indicator LED stops flashing after 10minutes, even if i
have not read my messages/missed calls.
I want the LED to flash until i take care...is there a way?
thnx in advance,
RB
Click to expand...
Click to collapse
I am working on this as I find time. Can you look in the registry at HKCU/Control Panel/Notifications/Led and tell me what the value of the TimeOut is set at?
Value LED Time out
Can you look in the registry at HKCU/Control Panel/Notifications/Led and tell me what the value of the TimeOut is set at?
In my HTC Snap the Value data is 30, but I don't think my Led is flashing voor 30 minutes.
Is this the right value?
famod said:
Can you look in the registry at HKCU/Control Panel/Notifications/Led and tell me what the value of the TimeOut is set at?
In my HTC Snap the Value data is 30, but I don't think my Led is flashing voor 30 minutes.
Is this the right value?
Click to expand...
Click to collapse
That is the correct value. I am still looking through the registry, but it may be something in a dll which would really be crummy.
Randel Burton said:
Hello, are there some news for the LED?
I own the European Version of the Maple (Snap)
and the indicator LED stops flashing after 10minutes, even if i
have not read my messages/missed calls.
I want the LED to flash until i take care...is there a way?
thnx in advance,
RB
Click to expand...
Click to collapse
Hallo,
i have the same Problem with der HTC Snap Status LED.
Have you found an Solution?
Maloja
cswroe said:
I am working on this as I find time. Can you look in the registry at HKCU/Control Panel/Notifications/Led and tell me what the value of the TimeOut is set at?
Click to expand...
Click to collapse
Very cool..looking forward and wish u lots of free time
My TimeOut value is 30, too.
It seems that the secret may be in allledmgr.dll
I am totally unfamiliar with editing dll files so if someone wants to take a try at it, go ahead. It looks like this file contains the flash rates, colors, etc.
No sooner did I give up and it came to me that what we need is not there rather than change what is there.
If you want the LED to blink until you acknowledge the message/notification you need to add a DWORD entry to the following paths in the registry. The DWORD that you want to add will be named "Duration" (without the quotes) and give it a DWORD Data of "0" (zero without the quotes).
For SMS: HKEY_CURRENT_USER\ControlPanel\Notifications\{A877D65B-239C-47a7-9304-0D347F580408}
For Missed Call: HKEY_CURRENT_USER\ControlPanel\Notifications\{A877D660-239C-47a7-9304-0D347F580408}
For Reminders: HKEY_CURRENT_USER\ControlPanel\Notifications\{15F11F90-8A5F-454c-89FC-BA9B7AAB0CAD}
The above work on my device. I do not use the built in VM or Email, so I can not confirm the following two entries so if someone would like to try and let us know, I would greatly appreciate it.
For Email: HKEY_CURRENT_USER\ControlPanel\Notifications\{A877D65A-239C-47a7-9304-0D347F580408}
For Voicemail: HKEY_CURRENT_USER\ControlPanel\Notifications\{A877D661-239C-47a7-9304-0D347F580408}
I still believe the secret to the colors reside in the dll posted above.
Hello,
many thanks for your help.
It functions very well.
Greeting
Maloja
LED blinking
No change over here!
Also the suggestion of Ookba to use automatic keylock doesn't make the timeout of blinking any longer.
famod said:
No change over here!
Also the suggestion of Ookba to use automatic keylock doesn't make the timeout of blinking any longer.
Click to expand...
Click to collapse
Interesting. Are you using Ookba's Rom?
I would check to make sure that you are in the right location and that the Value is correct. I will make a file that will do it automatically when I get a chance. The locations are so similar I was putting my values in the wrong location at first.
cswroe said:
Interesting. Are you using Ookba's Rom?
I would check to make sure that you are in the right location and that the Value is correct. I will make a file that will do it automatically when I get a chance. The locations are so similar I was putting my values in the wrong location at first.
Click to expand...
Click to collapse
I'm sorry, on the right place everything is blinking oké. Thanks
cswroe said:
...
If you want the LED to blink until you acknowledge the message/notification you need to add a DWORD entry to the following paths in the registry. ...
Click to expand...
Click to collapse
Thank you mucho!
Works fine on my Euopean (GER) Snap. Finally! THANKS AGAIN!
Somebody know if this works with 6.5, too?
Randel Burton said:
Thank you mucho!
Works fine on my Euopean (GER) Snap. Finally! THANKS AGAIN!
Somebody know if this works with 6.5, too?
Click to expand...
Click to collapse
I am using 6.5 and it works fine.
Hey Guys and Gals,
I have a small question and I hope somebody knows the answer.....
I'm having a Snap ans I was wondering if if could be possible by settings to leave the screen dimmed while getting a text....
usually it brightens up and turns on as soon as you get a message, but I dont want that
Is there somebody who knows, how to disable the screen from being turned on while receiving a message??
Thanks anyway for any reply/feedback
Regards Jeroen
i think that might just be part of the background sms process. i don't believe there is any hidden registry value to change it.
djh816 said:
i think that might just be part of the background sms process. i don't believe there is any hidden registry value to change it.
Click to expand...
Click to collapse
Are u sure? There should be something....I've had a Diamond before and it was possible to change that....
anybody else?
Thanks
Come on...really nobody???
hmm.... never mind.....thanks neway
You could try this reg hack:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\RIL]
"DisableSMSWakeUpEvent"=dword:00000001
Click to expand...
Click to collapse
bubble said:
You could try this reg hack:
Click to expand...
Click to collapse
Thanks for your reply! I will report if it works
Regards Jeroen
Can anyone provide some help?
I used a program called SPBTV, as soon as I touched the backlight function there, it disabled my phone's own adjustment(except Auto).
Start->Settings->Sound&Display->Backlight->Backlight Adjustment
Both options are disabled.
Please help, thanks a lot in advance!
Well, I found a solution by searching:
http://forum.xda-developers.com/showthread.php?t=631049&page=197
So warning: be careful when using SPBTV...
Anyone has better idea? Like modify registry?
http://forum.xda-developers.com/showthread.php?t=636980
kilrah said:
http://forum.xda-developers.com/showthread.php?t=636980
Click to expand...
Click to collapse
Thanks a lot! It works. The stupid SPBTV sets the value to 0 which suppose to be 1-10.
Anybody knows why the battery power slider has disappear?
See Images Blow.
"Automatically Adjust Backlight" checked in pic one, unchecked in the other.
alsalahi said:
Anybody knows why the battery power slider has disappear?
See Images Blow.
Click to expand...
Click to collapse
By any chance you installed spb tv?
HKCU\ControlPanel\BackLight\Brightness Change to 3
I had the same problem like this, because of the stupid SPB TV program. It sets the value to 0, which is out of range(1-10).
Just reset the registry value as 1-10 then the slider will come back.
alsalahi, even if you haven't used spb tv I would still start by checking that reg value, I've read about it getting changed by other things as well, and changing it to a value >= 1 always seems to clear it up just fine.
Problem Solved
justwonder said:
By any chance you installed spb tv?
HKCU\ControlPanel\BackLight\Brightness Change to 3
Click to expand...
Click to collapse
Yup I have installed spb tv trial and it causes this problem.thanks justwonder problem now is SOLVED.
sirphunkee said:
alsalahi, even if you haven't used spb tv I would still start by checking that reg value, I've read about it getting changed by other things as well, and changing it to a value >= 1 always seems to clear it up just fine.
Click to expand...
Click to collapse
thanks dude problem is solved now.
Hello to all
Will anyone please tell me how we will decrease the vibration sensitive in htc keyboard etc....
Thanks to all
will any one have a solution?
shafizal said:
will any one have a solution?
Click to expand...
Click to collapse
Hello..
Try to play with:
[HKEY_LOCAL_MACHINE\Software\OEM\KeyState]
ausdim said:
Hello..
Try to play with:
[HKEY_LOCAL_MACHINE\Software\OEM\KeyState]
Click to expand...
Click to collapse
thanks bro but my keyboard vibrate state is already in value 1 but still my vibration is heavy
shafizal said:
thanks bro but my keyboard vibrate state is already in value 1 but still my vibration is heavy
Click to expand...
Click to collapse
[HKEY_LOCAL_MACHINE\Software\OEM\KeyState]
"APPLICATION_BTN_VIBRATE3" --> try to decrease the value
williyung said:
[HKEY_LOCAL_MACHINE\Software\OEM\KeyState]
"APPLICATION_BTN_VIBRATE3" --> try to decrease the value
Click to expand...
Click to collapse
thank u very much brother it works fine now