Database Users

cant get out from align screen!!!!!!!!

need help from you guys.
my customer came to me with BOOTLOADER Screen 5.17 GSM OK, so i upgrade using SD (Patch ) and upgrade rom 3.17..., and radio 4.21,
After all complete, setup screen is come out, but i cant get out from Alignn Screen.
Can this problem solve using Software Sulition?? or it have Bad Screen ???
When i test using TEST Menu, touch test said PASS.... ???
how can it be ???
please Help

Mine is doing the same do a reset and then leave it for about 5 Min's at the loaded screen
The tap screen and then try to do align if it freezes again reset and try again sometimes it takes me 2 or 3 times to get it done
Once done it works fine until next hard reset
Only started doing this recently don't know what is causing this
Good luck
Jules

still havent suceess here.... need help

still havent suceess here.... need help

i can manage the problem by resoldering Caps around its connector.
Thx u

Please be more clear
Hello mrgsm
Please tell more clearly what you did, where exectly did you resolder?
I have the same problem.
Did the problem go away when you resoldered?
brgds
Svend_e

Problems Formating

Hi Guys,
Well yesterday the Battery on my 9100 went flat this has happened before and I just charge it back up and its fine.. But this time I incurred Data Loss
Went to turn it back on and it locks on the Boot screen where its states the GSM etc.. Have gone through the usual key press to format and I keep reciving format failed
Any help would be most appriciated

Get to the bootloader screen (multicolored) by turning device off - hold camera button and turn on. Sounds like you need to reflash you device with the same or updated rom - all the wizard roms are listed in the wiki - link is top left on your screen

ul, prehaps its cos your knees are too bendy?
Imp

Ive tryed changing the rom to a newer version, but still no avail... still saying format failed.. Any more ideas before I have to send it back to Qtek... which I would really rather not do

Droc said:
Ive tryed changing the rom to a newer version, but still no avail... still saying format failed.. Any more ideas before I have to send it back to Qtek... which I would really rather not do
Click to expand...
Click to collapse
Did you sort this out? I can get to the multicolored screen and flash my wizard but it never boots past the second splash screen. I think the extended rom is corrupted somehow and I need to clear it but hard reset just ends with format failed? Any ideas?
J

S200 hangs in bootloader after softreset

Hi all,
Since last friday I'm the happy owner of an S200, until sunday atleast. After a soft-reset, initiated from windows, my device won't boot anymore. It hangs in the red-green-blue bootloader screen (says: IPL 2.09, SPL 2.09). I've tried soft-resets and hard-resets, but the device would consequently keep hanging in the bootloader.
So for the past few days I've been searching the web and just managed to update the ROM. I was expecting that updating the ROM succesfully would mean my device would boot again, but it still keeps hanging in the bootloader (saying IPL 2.09 SPL 2.15 now, so the update did take place).
Does anyone has any idea whats wrong with my phone? Or how to fix this? Please help.

* bump *
I've been searching further and tried to do a SD dump, but I'm getting the message I don't got enough rights to perform a SD dump. This meens my S200 isn't CID unlocked. Is there any way to CID unlock the device without the need of booting into WM?

The solution to your problem
Hello, if you are having bootloader screen right after starting your mobile (prophet) check if your camera button is depressed since i had the similar problem. In my case i had to disassembly the phone in order to fix it. Right after fixing the button it worked fine

hi syzzer,
i really feel with you - why? - i have the exactly same problem. after i tried to upgrade my rom from o2-germany to another one the device isn't starting anymore and hangs in the beautiful-colored bootloader. and now, if i just even want to re-install the same or another rom, doesnt matter which one, the s200 wont start again. i think this is a really unlucky situation for us to stand alone with our weak pda =) hoping for more help, otherwise we have to take up our warranty and try to get it fixed by the store we did buy it (if a rom-update damage is still in warranty )
good luck
budy!

awechris said:
Hello, if you are having bootloader screen right after starting your mobile (prophet) check if your camera button is depressed since i had the similar problem. In my case i had to disassembly the phone in order to fix it. Right after fixing the button it worked fine
Click to expand...
Click to collapse
in my case, the camera button is not pressed in... i truly don't know what to do hopeless? mhm?
greets!
budy!

hello Syzzer
I have the same problem, but i make a soft reset and it works.
Camera but + Com Button + Power
Wait until message appear.
You Get the message : For Hard reset press send
If you choose other key the system boots normaly.

I had already tried all your suggestions, but nothing seemed to work.
About a month ago I bought a Trinity. In the mean while, I forgot I had put my S200 in my bag and carried it around for a month. When I found it a week ago and started pressing random buttons, it suddenly booted and has been working ever since! The problem has gone as mysterious as it came. I can only imagine there was some hardware failure / dirt in my device that caused the trouble and is now gone / moved to some place it does not do harm. Because I already bought a Trinity, I gave the S200 to my brother. He's been using it ever since and did not have any problems. So keep your head up, there's hope!

I m also having the same problem
Now I am having the same problem, no button is pressed, and I can not install the NVID ROM
Actually I can install only a few ROMs, the NVID ROM was working before on my Neo perfectly but, I think it can be because I have changed many ROMs, from a month, actually I have tried different WM6 ROMs and I used NVID ROMs mostly for Step 1.
Now when I install any ROM, it shows a msg some nbf one after 80% or 95%
It can install the pdaviet first step ROM, but now the problem is that it hangs very much and it can not start Wifi, it has stopped working, a few more ROMs i have tried, but the WIFI is completely stopped.
When I press it in communication manager, it will show busy icon for a few seconds and will not start it in end.(I tried it in both WM5 and WM6, same problem, I also tried after soft reset and hard reset, the problem is still there)
Please someone help me out.

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

wont boot...didnt even rom upgrade!

so i was just trying to charge my phone and the screen gave all these funny characters and the screen froze up, so i reset it with the reset button. it does get to the white HTC screen with red wording but thats it....whats up? can i use the techniques of the failed rom flashes to try to boot my phone?
phone charges though =P....but what good is that. any ideas before i just try to hard reset (and do a rom update for the heck of it)?

I bad the same problem last week. The HD runs after formating the storage-card and reflash a new ROM.
PS only flashing has no working.It's possible that only formating works...

Try to take the battery out for 1 minut and the start it again, it worked for me.