Database Users

Blueangel WM6 Contact list problem.

Ok so here's the problem:
Whenever i want to go to my contact list, either by pressing the contact button, or going to my contact list via, Phone or "Contacts" on the start menu, it just flashes "contacts" at the top, doesn't display my contacts, and then just goes back to the today screen.
Is there a fix for this?
Many thanks.

Anyone?

did you perform "power&reset + no/yes/yes + mail button" the first time?

raymonds said:
did you perform "power&reset + no/yes/yes + mail button" the first time?
Click to expand...
Click to collapse
No i didn't, is there anyway i can sort that out?

well, as nike said, "just do it". your problem would most likely be solved.

raymonds said:
well, as nike said, "just do it". your problem would most likely be solved.
Click to expand...
Click to collapse
I've pushed power&reset,.. but nothings come up, and it goes through the usual boot up.
As for the mail button, where do i find that?

are u sure u have a blueangel device ?

Xeon said:
are u sure u have a blueangel device ?
Click to expand...
Click to collapse
Hell yes i'm sure XDA IIs, PH20B.
Written on the back, underneath the battery.

Steve123456 said:
I've pushed power&reset,.. but nothings come up, and it goes through the usual boot up.
As for the mail button, where do i find that?
Click to expand...
Click to collapse
as soon as you push power&reset, you now press the camera&record buttons simultaneously. three lines will come up, and you use both camera & record buttons to navigate and toggle from no to yes to no... so at the end you'll get no/yes/yes (1st line/2nd line/3rd line)
the mail button is the 2nd button from the left (the one with the envelope icon).
all of these are in the wiki, which you're supposed to read before you attempt to upgrade. it appears you haven't done any reading yet, hehe...

Lool ok , now the mail button is the SECOND BUTTON BELOW THE SCREEN , with the Mailbox icon, next to Start up menu button on the left and the IE button on the right , to be more specific , the one with the set of 4 buttons . U can easily find it by look at the FRONT SIDE of the device . In Any case , you DID NOT find it , ill post you a Screenshot . cheersss

raymonds said:
as soon as you push power&reset, you now press the camera&record buttons simultaneously. three lines will come up, and you use both camera & record buttons to navigate and toggle from no to yes to no...
the mail button is the 2nd button from the left (the one with the envelope icon).
all of these are in the wiki, which you're supposed to read before you attempt to upgrade, hehe...
Click to expand...
Click to collapse
Silly me!
I did read the Wiki (Much help), and from there it was straight forward, it was just this little problem that was bugging me, but thank you very very much.

you're welcome. have fun with your new wm6!

raymonds said:
you're welcome. have fun with your new wm6!
Click to expand...
Click to collapse
Bingo,.. it's working.
Everythings running in order, just like it did when i had WM5.
oooh,.. i wonder if i still have Worms World Party on it.

that will be lost... a result of the no/yes/yes action you did.
in any case, i assume you wouldn't have any problem installing the said game.
cheers!

raymonds said:
that will be lost... a result of the no/yes/yes action you did.
in any case, i assume you wouldn't have any problem installing the said game.
cheers!
Click to expand...
Click to collapse
I got a backup sitting somewhere.
I'm not too fussed though that i've lost it, cause this device serves me alot more than just a games device.
(Jawbreaker is a time waster enough)

[APP/HACK] disCali 0.1 - Disable Align Screen

Hey,
What does it do?
Disables "Align Screen"
Motive:
While playing games with my HTC Mogul I've stumbled upon an annoying thing, whenever you press the middle D-PAD button + Message Button, the "align screen" window pops up and won't go away until you complete the alignment process. This sucks considering I never really need to align my screen and I do need those buttons to play comfortably.
Anyhow, I couldn't find any other working solutions so I coded it myself.
I used some pretty advanced hooking techniques and I'm pretty sure this will work on every device with no tailoring. I'd appreciate any feedback stating what device you tested it on.
Instructions:
1. Install the cab.
2. Run "disCali" form Start Menu > Programs, this will disable the align screen function from your entire device until soft-rest (even from the control panel).
3. Run it again and it will restore everything back to normal.
hope you'll find this useful,
amit

Thank you thank you thank you testing right now will let you know

nice app ..

create an empty file naming welcome.not and copy to your SD card. and insert it in your phone it should stop screen align

rajivshahi said:
create an empty file naming welcome.not and copy to your SD card. and insert it in your phone it should stop screen align
Click to expand...
Click to collapse
This app has nothing to do with preventing the after-boot welcome "align screen", it's meant to prevent the hot-key "align screen" pop up during every day use of the device.

amp3r said:
This app has nothing to do with preventing the after-boot welcome "align screen", it's meant to prevent the hot-key "align screen" pop up during every day use of the device.
Click to expand...
Click to collapse
OOOps my bad
thought you wanted to stop the align screen... as in my device the only time i get align screen is after hard reset....

keep up the good work dude......

i really need a disCali version which doesnt show the message to call it at startup. or one which only shows the "re-enabled" message, but did not inform about disabling.
If you could make my wish come true, i would be really thankful!
thanks anyway for this useful tool!
Andreas

Thank you!
This annoyance is now finally gone.
Too many times I've pulled my phone out of my pocket with an "align screen" staring at me.
Maybe with normal locking this can't happen but I'm using S2U2.

very useful!
thanks amp3r!
now i can assign the volume buttons and center dpad button in Final Burn on my Opal and play it without the annoying Align Screen.

Stucked at Align Screen
amp3r said:
Hey,
What does it do?
Disables "Align Screen"
Motive:
While playing games with my HTC Mogul I've stumbled upon an annoying thing, whenever you press the middle D-PAD button + Message Button, the "align screen" window pops up and won't go away until you complete the alignment process. This sucks considering I never really need to align my screen and I do need those buttons to play comfortably.
Anyhow, I couldn't find any other working solutions so I coded it myself.
I used some pretty advanced hooking techniques and I'm pretty sure this will work on every device with no tailoring. I'd appreciate any feedback stating what device you tested it on.
Instructions:
1. Install the cab.
2. Run "disCali" form Start Menu > Programs, this will disable the align screen function from your entire device until soft-rest (even from the control panel).
3. Run it again and it will restore everything back to normal.
hope you'll find this useful,
amit
Click to expand...
Click to collapse
thanks for this beautiful innovation.........u actually went to think Outside the Box to achieve this..........I am stucked in here....I have a Sony Ericsson Xperia X1 which refuses to align screen after a hard reset.How do i implement this solution of urs to try and see if it would sove the problem??I have tried the remote pingy thing,it bypasses the Align screen but my fone becomes useless.....Nothing on the screen works including the key board...I presive this would be a better solution provided the Aligning of the screen is taken care of in the File you have written and uploaded

How to bring back auto screen lock?

Hi all,
Just upgraded ROM to 1.48, but now I have lost the screen lock when you turn the device on! I dont want the phone doing random things in my pocket if a button is pressed..

wackyD said:
Hi all,
Just upgraded ROM to 1.48, but now I have lost the screen lock when you turn the device on! I dont want the phone doing random things in my pocket if a button is pressed..
Click to expand...
Click to collapse
Sorry mate - no answer for you, but a question.
I'm about to upgrade to 1.48. Does that get rid of the auto lock for everyone then, or is it maybe a problem that you're having and others aren't? It's actually something that would make me think twice about upgrading!

wackyD said:
Hi all,
Just upgraded ROM to 1.48, but now I have lost the screen lock when you turn the device on! I dont want the phone doing random things in my pocket if a button is pressed..
Click to expand...
Click to collapse
What do you mean you lost it ?? Just press the rightmost end button hard and you have a menu:
Power off
Lock Device
Set vibrate
Terminate Data Connection
This is default in rom [email protected]@@

You need to press & hold now. Before, you needed only to press it.

Let me get this straight...
If you press the end call button (just briefly) to put the phone in standby, when you press it again, do you get the lock screen??

Ahh that sucks, I want the old setup back. Any ideas?

I've just finished installing 1.48, and it works exactly the same as it previously did (for me).

wackyD said:
Hi all,
Just upgraded ROM to 1.48, but now I have lost the screen lock when you turn the device on! I dont want the phone doing random things in my pocket if a button is pressed..
Click to expand...
Click to collapse
Start reading from this page

Start, then press "Lock" appkey in bottom left corner.
After that all ok. End call button now locks the phone.

I've had the same problem. What was suggested by locking the screen from the Start menu did fix the problem. This has happened a couple of times since installing the 1.48 rom.
I also noticed that I was having a problem where I couldn't open e-mails from the touch flo interface. When I clicked on a message, it would just push down and come back up but not open the message in outlook. This problem was resolved when I fixed the lock screen....has anyone else experienced this as well?

just install BsB Tweaks 1.2 and enable this option!
btw. this is a very usefull option

crazyman1 said:
I also noticed that I was having a problem where I couldn't open e-mails from the touch flo interface. When I clicked on a message, it would just push down and come back up but not open the message in outlook. This problem was resolved when I fixed the lock screen....has anyone else experienced this as well?
Click to expand...
Click to collapse
I can confirm that this exact thing happened for me. I couldn't open an email, so I locked it from the start menu, unlocked it, and could immediately open the email.

hbc said:
Start, then press "Lock" appkey in bottom left corner.
After that all ok. End call button now locks the phone.
Click to expand...
Click to collapse
Not for me :-(

crazyman1 said:
I've had the same problem. What was suggested by locking the screen from the Start menu did fix the problem. This has happened a couple of times since installing the 1.48 rom.
I also noticed that I was having a problem where I couldn't open e-mails from the touch flo interface. When I clicked on a message, it would just push down and come back up but not open the message in outlook. This problem was resolved when I fixed the lock screen....has anyone else experienced this as well?
Click to expand...
Click to collapse
I had the same issue and installing net3.5 or bsb did not fix it. I too pushed start then the soft key "lock" (in lower left corner of screen) and both my email and lock issue was fixed. BUT it came back two times today, I think it had to do when I installed a new program, not every time, but I fixed it the same way. This has to be a bug.

greatcapp said:
You need to press & hold now. Before, you needed only to press it.
Click to expand...
Click to collapse
Yes this is an additional option. You can still press end button slightly ( or just lightly tap it ) and the screen will lock ( you will see the default "slide" on top ). This no need any tweak and is a default feature in the 1.48 rom

mobile88 said:
Yes this is an additional option. You can still press end button slightly ( or just lightly tap it ) and the screen will lock ( you will see the default "slide" on top ). This no need any tweak and is a default feature in the 1.48 rom
Click to expand...
Click to collapse
And, as I answered before. This isn't working for me.
I have to hold the end button, then select "Lock screen".
Before the upgrade in ROM, I could just tap the end button - now that no longer works. I have to hold it, then select "Lock Screen".

greatcapp said:
And, as I answered before. This isn't working for me.
I have to hold the end button, then select "Lock screen".
Before the upgrade in ROM, I could just tap the end button - now that no longer works. I have to hold it, then select "Lock Screen".
Click to expand...
Click to collapse
I think he means that when you press the end button the screen turns off. I know it's not actually locking the device, but the screen is off.
From my experience, the start menu lock resets something and allows the lock screen to work. This will work until the phone is restarted, which is when the problem is caused.

To fix this problem and get back the auto lock option....do the following:
with any registry editing software:
HKEY_CURRENT_USER
Control Panel
Keybd
DefaultKeyLock --------> change value to 1

johncmolyneux said:
I think he means that when you press the end button the screen turns off. I know it's not actually locking the device, but the screen is off.
From my experience, the start menu lock resets something and allows the lock screen to work. This will work until the phone is restarted, which is when the problem is caused.
Click to expand...
Click to collapse
Ok, sadly, the start, then lock workround isn't working for me. Just pressing the end key, turns off the screen, but doesn't lock it any longer. I'm trying to figure out how to get the .dll into the windows folder (as advised from the other thread). But I can't seem to do it. I can move the .dll file onto the handset, but then can't see it to move it to the windows folder. And I can't put it directly into the windows folder on the handset, as I can't see it from my desktop.

Activating "Auto Lock" from within BsB Tweaks seems to have sorted the issue for me

HELP ! Screen calibration issues with My Mobiler

Managed to mess up my screen a little bit and now when I did a hard reset couldn't pass the align screen step. Finally after some research I managed to skip it.
Now when I try to align my screen using MyMobiler I cannot manage to move the cursor target on my desktop computer so I can align the screen from there. I tried to double-click the target cursor, drag it, etc ...nothing works. What am I doing wrong ? or it cannot be calibrated with MyMobiler ?
PLEASE HELP, noobie !
THANKS !

rzvnb01 said:
Managed to mess up my screen a little bit and now when I did a hard reset couldn't pass the align screen step. Finally after some research I managed to skip it.
Now when I try to align my screen using MyMobiler I cannot manage to move the cursor target on my desktop computer so I can align the screen from there. I tried to double-click the target cursor, drag it, etc ...nothing works. What am I doing wrong ? or it cannot be calibrated with MyMobiler ?
PLEASE HELP, noobie !
THANKS !
Click to expand...
Click to collapse
If you managed to skip the calibration screen, then just skip it then start using MyMobiler. Will that work?

talontsi07 said:
If you manages to skip the calibration screen, then just skip it then start using MyMobiler. Will that work?
Click to expand...
Click to collapse
I skipped it but now the screen still needs to be calibrated somehow. My screen taps are messed up. I tap the low corner of my screen and my start menu (top corner) pops up, etc.

rzvnb01 said:
I skipped it but now the screen still needs to be calibrated somehow. My screen taps are messed up. I tap the low corner of my screen and my start menu (top corner) pops up, etc.
Click to expand...
Click to collapse
Yes taping the screen will be all messed up, but if you use MyMobiler it shouldn't need to be calibrated. In theory I think thats how it should work, but iv never tried.

[Q]Screen Problem

Hey,
I have an HTC HD and love it. But I have a problem with screen.
When I push at the middle of the screen, it perceives the command wrong and acts like i push at the bottom of the screen. And when I push start button, it acts like I push the clock.
Aligning the screen from Settings menu works but only for 5 or 10 minutes, then it break itself down again.
What can I do ?
Thank you !

Knuckled said:
Hey,
I have an HTC HD and love it. But I have a problem with screen.
When I push at the middle of the screen, it perceives the command wrong and acts like i push at the bottom of the screen. And when I push start button, it acts like I push the clock.
Aligning the screen from Settings menu works but only for 5 or 10 minutes, then it break itself down again.
What can I do ?
Thank you !
Click to expand...
Click to collapse
try using this CalibrationData maybe it could help

I do not know how to use it

Knuckled said:
I do not know how to use it
Click to expand...
Click to collapse
you simply extract to your device and import the registry file that exists in the package
if the post is useful to you, press the thanks button

HTC HD Screen Problem
Yo Mate. Thanks alot it works. I have been trying to solve this problem few months back but fail. SAtumbled upon this tread and Ta Da. You've made my day. Hope it'll last.
THANK YOU THANK YOU THANK YOU

Help
ok maybe I sound stupid, but how the F***K to use it.
I have the same problem as mentioned above.
I downloaded it on to my pc then I put the zip file on my Touch HD straight into my root and even on my sd-card.
Whats next to do, when I clic on it it goes to zip mobile, at least in left corner of the screen it says so. I see a + mark and when I clic on it it colapse and then an other + shows up (CalibrationData folder) and then beneath CalibrationData.reg file.
So any smart guy or girl can help me out.
Grtz xxxware

There must be something in the air(waves)!
See: http://forum.xda-developers.com/showthread.php?t=1075957
I've had nothing like this happen before, and not heard of it happening before, then all of a sudden three instances (like a bus).
I'll try this calibration data but my phone would let me calibrate now it won't, it's just gotten worse!