Wipe questions.... - Nexus One General

So I'm feeling fairly comfortable now about flashing settings, but one question I did have. On the wipe option of the recovery, there are several options: Dalvik-cache, battery status, and rotate settings. Can anyone give some clarification on these three?
Specifically, I'm looking for if/when I should wipe the battery status.
Thanks always in advance...

i wipe the batterstats every time i am in recovery. sometimes im not in the recovery for a while, so ill wipe them through the terminal. it keeps your battery meter accurate, after some time of charging when the power isnt completely drained or powering off when its not completely drained and rebooting, the meter becomes inaccurate. its just a way of reseting it.

Related

How can i make battery life last longer?

i keep trying every rom available for my phone
and in every rom is the same the 100% battery last for like 3 hours then after that the battery drops like every minute even when screen is off?
how can i make battery life last longer?
thanks in advance
Lucky for you I still had copy of it in message box as I got 5-6 requests few hours ago regarding that.
BlackSHELF said:
Well the borderline idea is the same as you already know you have to completely drain it. Now never use any volt meter those people use to completely discharge it as the negative effect I already explained to you in that post. So best way is to do it by recalibrating so what you do is:
1) Fully charge it.
2) Drain it till you get 1%.
3) Go in recovery and wipe battery, reboot (batterystats.bin created).
4) As you still have battery low now let it charge till 100%.
5) Do the cycle again.
NOTE: This is what I would recommend but as we know the whole issue with CWM restarting while phone is off as you can flash the stock recovery and go back as it takes 3sec. If not follow the above.
1) Heavily use your phone so it drain the battery till its 1%
As you will see the low battery light flashing just so you don't lose your data save it by rebooting.
2) As you still have some battery power left you can now go to Recovery and wipe battery stats.
Or you can manually do it from adb shell by using remove command "rm /data/system/batterystats.bin".
3) Keep it on till its turns itself off.
As you may have guessed it still has power left so keep using the device till its drained completely I would recommend rebooting and going in bootloader as it uses more power due to bight screen as Recovery uses less power on display.
4) Now turn it back on again in bootloader till it turns off again.
It will keep turning itself of as no power left, this is what you want. This is safe way to discharge it without having negative adverse effect.
5) Now let it charge via A/C instead of USB.
Now when the light turns green unplug it and replug it till its green again, keep doing that till you see its green only. Now once you reboot in Android it will rebuild the batterystats.bin and you will be fully recalibrated.
Click to expand...
Click to collapse
if i cant go back to stock recovery which procedure do i try the 1st procedure or the 2nd one?
nulights said:
if i cant go back to stock recovery which procedure do i try the 1st procedure or the 2nd one?
Click to expand...
Click to collapse
First one is better for you. Do the cycle fully twice and you will be good to go and it will solve those most common issue like getting green light while its still not 100% or sticking it at 100% for long time and then dropping faster than you can count lol I just did it few hours ago, normally I do it once every 2weeks.
Alright thanks,
Ill try this out
BlackSHELF said:
Lucky for you I still had copy of it in message box as I got 5-6 requests few hours ago regarding that.
Click to expand...
Click to collapse
I don't see a way to wipe battery stats in stock recovery. Doesn't that mean I have to wipe stats, reboot phone, switch to stock recovery then bootloader drain the phone? Will that reboot adversely effect the rebuilding of the bin file? Can I just delete the batterystats.bin file with root explorer before I power down the phone to start the bootloader drain process?
Edit: I'm at 3%, #push knowledge darinmc GOGOGOGOGOGOGOGOGOGOGO
darinmc said:
I don't see a way to wipe battery stats in stock recovery. Doesn't that mean I have to wipe stats, reboot phone, switch to stock recovery then bootloader drain the phone? Will that reboot adversely effect the rebuilding of the bin file? Can I just delete the batterystats.bin file with root explorer before I power down the phone to start the bootloader drain process?
Edit: I'm at 3%, #push knowledge darinmc GOGOGOGOGOGOGOGOGOGOGO
Click to expand...
Click to collapse
Sorry was asleep but yeah you can manually do it from terminal (su), adb (shell), root exp (enable r/w). Then power down as you saying you reverted back to stock recovery I am guessing you are on 3.0.0.6 supporting the 2.5.1.4 stock. So in that case just reboot and follow the same meth. This would clear out those lag (sticking at 100% for long time and then dropping faster than you can count) and wrong data (exp: 80% after rebooted 83%). I just recalibrated it yesterday which is the reason I spoke about it which caused this whole massive PM attacks and threads like this. Which is fine just do it once every 2weeks or once a month as doing it every week is not particle even for me.
BlackSHELF said:
Sorry was asleep but yeah you can manually do it from terminal (su), adb (shell), root exp (enable r/w). Then power down as you saying you reverted back to stock recovery I am guessing you are on 3.0.0.6 supporting the 2.5.1.4 stock. So in that case just reboot and follow the same meth. This would clear out those lag (sticking at 100% for long time and then dropping faster than you can count) and wrong data (exp: 80% after rebooted 83%). I just recalibrated it yesterday which is the reason I spoke about it which caused this whole massive PM attacks and threads like this. Which is fine just do it once every 2weeks or once a month as doing it every week is not particle even for me.
Click to expand...
Click to collapse
Thanks! Needed to do this for a while.
BlackSHELF said:
Lucky for you I still had copy of it in message box as I got 5-6 requests few hours ago regarding that.
Click to expand...
Click to collapse
thanks for that. I have been searching for that kinda guide on here for awhile! It was like looking for a needle in a haystack there are ten million about it, But none this detailed infomation!
SetCPU can help with your battery life. It did wonders on my HD2 running android.
Some suggestions in this thread: **HOW TO MAKE YOUR BATTERY LIFE LAST** Members Tips & Tricks
can someone clarify the steps "Go into recovery and wipe battery"?
I am running stock rom.
I am able to go into the bootloader menu. But when I select recovery, all i get is an icon with a picture of a phone and a triangle w/ an exclamation point at the corner. I don't know to leave this screen other than battery pull.
Where do I delete batterystats.bin?
Wiping battery stats help
I tried to wipe battery stats after my battery was drained to 1%, but nothing happened. I didnt see any scripts run that confirmed battery stats command had gone through. Was that supposed to happen? I'm really confused by this because I saw that my battery was drained to 1% but when I rebooted to recharge the phone, it showed that I was not fully drained. It read that I was at 20% and charging!? Please help guys. Thanks in advance
longhornguy said:
I tried to wipe battery stats after my battery was drained to 1%, but nothing happened. I didnt see any scripts run that confirmed battery stats command had gone through. Was that supposed to happen? I'm really confused by this because I saw that my battery was drained to 1% but when I rebooted to recharge the phone, it showed that I was not fully drained. It read that I was at 20% and charging!? Please help guys. Thanks in advance
Click to expand...
Click to collapse
Download and use "battery calibration" app from the market. Its pretty easy to understand and follow.
Sent from my HTC Glacier
Thanks man, i greatly appreciate it. I'll download and see what happens

[FIX] Battery Stats Issues!

Ok After some tinkering I was able to fix Battery stats issue and actually find out a possible reason for battery stat issues pitfalls and random shutdowns.
Here are the Steps I got working after my battery reported wrong stats and huge pitfalls with Random Shutdowns. Fix is pretty simple but needs a bit of patience so here goes:
Note: I tried this on Overcome ROM 1.4.2 with 2.1.2 overcome kernel. Some users report that new Asian Firmware in GSM development section has this issue solved.
First: follow the instructions below to get a fresh new battery stats and recalibrate the battery.
alterbridge86 said:
If you have Battery Life issues, try this first:
Turn the Tab off and charge to 100%
Unplug from charger and immediately boot into recovery by holding volume up & power button
Navigate to Advanced
In the Advanced menu, choose Wipe Battery Stats
Reboot Tab normally and Enjoy a freshly calibrated battery
NOTE - Having the tab off is important...I notice that even if I charge to full while tab is on, once I turn it off it continues charging for another 10 minutes or so before hitting 100%. I believe the sensor determining what is a full battery is different in the off position and will allow you to get the fullest charge.
Click to expand...
Click to collapse
(credit to alterbridge86 and original poster).
Second: Use the tab till its fully drained (you may experience random shutdown and pitfalls keep rebooting it till its COMPLETELY DEAD. We need a full drainage to obtain a charge Discharge Cycle. Press the power button to force any charge out and make sure the tab battery is completely out.
Third: Repeat the The Charge/Discharge cycle (mine worked after the 3rd time). You should experience improved battery stats with each cycle until all issues are gone.
As for the possible reason for the Battery stats issue I am suspecting USB charging from computers when we use the tab with PCs to sync or copy or flash ROMs on the tab (I started having those issues after tab was on laptop for the whole day as I was trying new ROMs and flashing overcome). I wonder if there is a way or script to disable USB charging. I could be wrong so feel free to correct me if I am
I hope this helps!
has anyone else here tried this method?
any success?
right now im trying the first part. let you guys know when its done.
just fully charged my tab.
got into samsung recovery. but cant find calibrate battery anywhere.
just
reboot system now
apply sdcard:update.zip
wipe data/factory reset
wipe cache partition.
help
did the wipe cache.
hopefully this does the job
he was talking about the custom rom though , you can wipe the battery status .
there is app in the market called barry calibration for free you may wanna have a look into it
You can find it under Advanced tab in recovery, wipe Battery Stats.
milkboy007 said:
just fully charged my tab.
got into samsung recovery. but cant find calibrate battery anywhere.
just
reboot system now
apply sdcard:update.zip
wipe data/factory reset
wipe cache partition.
help
did the wipe cache.
hopefully this does the job
Click to expand...
Click to collapse
when i unplug my tab the level immediatly goes to 99%.
I've tried to calbrate but the problem is still there.
Any solution?
thanks in advance
sadly i use the stock rom.
oh well hopefully 2.3 upgrade fix the issue
The Solution
milkboy007 said:
sadly i use the stock rom.
oh well hopefully 2.3 upgrade fix the issue
Click to expand...
Click to collapse
milkboy007, consider your self lucky that I'm here to help you with a problem that faced me for over a month and i finally fixed it, which is exactly your problem, forget about all the non sense these people say about calibrating the battery or changing roms its all waste of time, here is the real solution open the tab and remove the battery let it settle down for 30 min and hook it back in and close your tab and you will be a happy tab owner again, i know it is hard to believe even for me at first i tried all the other methods the guys said with no hope, but now I'm really happy with my tab again, you need a tri wing screw driver and some other plastic case opener to open it for me i used a regular screw driver but be careful from scratching your case while opening it, here is a link on how to open it and other link for guys who had the guts to do it and telling what they experienced
http://www.ifixit.com/Teardown/Samsung-Galaxy-Tab-Teardown/4103/1
http://www.youtube.com/watch?v=urGUKerJOhg
http://forum.xda-developers.com/showthread.php?t=986067&page=3

Battery Issues SOLVED!- New Solution...after I tried many..this works!

Hi all;
so over the last few months i have flashed many custom roms, kernels etc...and always had battery issues...i have tried jugs battery fix, wiping battery stats..following many other battery optimization threads..but i never got the battery life i once had (when i first bought my phone)...
a few days ago my phone totally crashed..wouldnt charge etc..and i ended up having to do a complete restore..i did this by following these instructions
http://www.youtube.com/watch?v=hRFJJFW-XxI
....so from there, i unlocked again, reloaded CWM etc and i loaded 2.3.4 flashable zip (found in the forums) via CWM.
and voila..battery life AMAZING....after 8hours im usually still at 85%...by evening time after using the phone all day im still at about 60%
from here do what you want with roms..
i loaded the alien rom without adding the themes..and the battery life is as stated above..
so if you are having issues try hard resetting the phone then re unlocking the BL and upgrading via cwm to 2.3.4
my battery life i back to amazing.....
p.s. would be great if someone else who is having issues tried this and reported back as well...
p.s. this worked for me but i am not responsible if you mess up your phone!
Erm..
Ok Ill bite >,>
Where are these camera buttons your referring to in this guide of yours Atrix has three hard buttons and four soft buttons power, vol- and vol+ and menu home back and search.... you hard mod a camera button into this already packed phone Ill like to hear it XP
Interesting..
Couple of q's:
- which camera button?
- unlock bootloader again? Once unlocked it stays unlocked.
- I don't understand how doing a reset leads you to unlocking the bootloader again?
Sent from my Motorola Olympus using XDA Premium App.
updated the hard reset instructions to reference a youtube video (not mine but describes how to do it)
http://www.youtube.com/watch?v=hRFJJFW-XxI
it doesn't actually re-lock the bootloader. The BootLogo is replaced with the stock logo, which does NOT include the "UNLOCKED" in the upper left hand corner
sorry i didnt realize that..so skip this step for anyone that is going to try it...
jakew02 said:
it doesn't actually re-lock the bootloader. The BootLogo is replaced with the stock logo, which does NOT include the "UNLOCKED" in the upper left hand corner
Click to expand...
Click to collapse
well dont have the old recovery and even if i did cant read the things at all quality is very bad
me too really can't understand it properly, i need to get back that battery time, but How? can anyone else explain it Please?
Anyone except TC try this with sucess? I have Alien 4 with stock kernel and i am getting about 15 to 20 hours before death.
I could be wrong, but I'm fairly confident that the following information is correct:
Doing a factory reset on the stock android recovery simply wipes data, cache, and dalvik - all of which can be done with any of the after market recoveries.
I am unsure as to whether or not factory reset also wipes the battery stats in the stock android recovery.
Edit: It is highly recommended to wipe the battery stats after you install a new ROM or kernel. To do so the quick and easy way - charge the phone to 100%, reboot to recovery, clear battery, reboot. If is then recommended that you let the phone die (or at least get low) followed by a full charge 2-3 times to make the battery accurate. The most involved way to reset the battery stats is to charge to full with the phone off. When it says 100%, pull the battery, plug it back in, let it charge for an additional hour or two while still off like this. It will likely not show 100% after an hour or two, that's fine. Boot into recovery, wipe stats, start up the phone, then unplug it. Follow this will drains and full charges 2-3 times and you will be set. This helps to fix poor battery life when it is caused by a battery that will not fully charge.
OP you should try to drain the battery down to nothing. A lot of people who screw up their battery stats end up with bad battery, however at times you can get a very slow draining batter that will give you 20 hours with 60% left, and then when the phone hits 53% (random example), the battery will fall from there to dead in just a few minutes. This happened to me when I first flashed Ninja SF. I was amazed the battery until I decided to let the phone actually die.
DK
Well im on Cm7 so far only 48% left after 18 hours of moderate use
Sent from my MB860 using xda premium
hi i did try what you said below and it didnt give me the same results...
DeathKoil said:
I could be wrong, but I'm fairly confident that the following information is correct:
Doing a factory reset on the stock android recovery simply wipes data, cache, and dalvik - all of which can be done with any of the after market recoveries.
I am unsure as to whether or not factory reset also wipes the battery stats in the stock android recovery.
Edit: It is highly recommended to wipe the battery stats after you install a new ROM or kernel. To do so the quick and easy way - charge the phone to 100%, reboot to recovery, clear battery, reboot. If is then recommended that you let the phone die (or at least get low) followed by a full charge 2-3 times to make the battery accurate. The most involved way to reset the battery stats is to charge to full with the phone off. When it says 100%, pull the battery, plug it back in, let it charge for an additional hour or two while still off like this. It will likely not show 100% after an hour or two, that's fine. Boot into recovery, wipe stats, start up the phone, then unplug it. Follow this will drains and full charges 2-3 times and you will be set. This helps to fix poor battery life when it is caused by a battery that will not fully charge.
OP you should try to drain the battery down to nothing. A lot of people who screw up their battery stats end up with bad battery, however at times you can get a very slow draining batter that will give you 20 hours with 60% left, and then when the phone hits 53% (random example), the battery will fall from there to dead in just a few minutes. This happened to me when I first flashed Ninja SF. I was amazed the battery until I decided to let the phone actually die.
DK
Click to expand...
Click to collapse

[INFO] Possible battery drain fix on many Custom ROMs

Well, after i tested almost every single ROM in the development section, there was a time that the battery behaved quite abnormal.
First when the phone was charging, many times it "jumped" from around 70% to 100%. While discharging with only WiFi open, it often drop from around 30% to 10-15% and then up again.
I tampered with the Governor setting, but it didn't improve much. But I did found something that somehow fixed the issue and improved the battery life quite a lot and also fixed the "jumps" while charging and discharging.
Backup whatever you need (SMS, Call Log, Bookmarks) from your favorite backup program
Download the Stock Rom Official RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1 , thanx to nitr00
Reboot in Recovery (CWM, 4EXT, whatever you use) and do a Factory Reset, Wipe Cache & Dalvik and Wipe Battery Stats
Flash the Official ROM you downloaded, reboot your phone and complete the Initial Setup.
Again, reboot in Recovery and do a Factory Reset, Wipe Cache & Dalvik
Flash your favorite ROM (clean install) and restore your program, settings and backups
All done :highfive:
I know that it's somehow strange method but it worked on my phone running IceColdSandwich v8.8 and on a friend's (had the same issues mentioned above) with PACman v16.1. I had no more "jumps" and the battery life improved significantly.
Since this is my first thread, i'd like to thank the fine community here in XDA for their work and efforts I really hope that the above advice help also other people.
Sounds interesting going to try it.
Hi,
thank you for sharing, got the same bug, and will try your method.
I will report back, if it worked
Bye,
MaDDy
Wipe dalvik cache, factory reset, format cache but not system?
Muikkuman said:
Wipe dalvik cache, factory reset, format cache but not system?
Click to expand...
Click to collapse
No, I didn't format /system, but feel free to try it... As I said in the first post, it surely is a weird fix. But worked for me
Going to try your version and see how it goes.
not sure if this works with viperdhd as it format system upon install.
Why is the Rom in 2 parts?
Worth trying, but I'd hate to have to reinstall all apps again... any chance it would work with nandroid backup of current ROM? i.e. Backup ROM, flash stock -> restore ROM?
@OP
Did you ever just try to use the superwipe script before flashing a new rom ?
Who?
Gonik said:
Well, after i tested almost every single ROM in the development section, there was a time that the battery behaved quite abnormal.
First when the phone was charging, many times it "jumped" from around 70% to 100%. While discharging with only WiFi open, it often drop from around 30% to 10-15% and then up again.
I know that it's somehow strange method but it worked on my phone running IceColdSandwich v8.8 and on a friend's (had the same issues mentioned above) with PACman v16.1. I had no more "jumps" and the battery life improved significantly.
Since this is my first thread, i'd like to thank the fine community here in XDA for their work and efforts I really hope that the above advice help also other people.
Click to expand...
Click to collapse
The problem with custom ROMs that battery isn't calibrated : ROM doesn't "know" what voltage is 100% charge, and what 1%.
An easier fix that worked for me
1) use your phone till it shuts down due to lack of power. It could easily work about 2-3 hours @ 1% level
2) charge it to full charge
Muikkuman said:
Who?
Click to expand...
Click to collapse
I meant the OP, to me it looks just like symptoms from flashing a custom rom without a proper wipe and/or not deleting the battery stats.
I'd also not recommend depleting the battery completely, a deep discharge isn't good for the battery.
Battery doesn't jump on custom Roms with kernel based on stock. Like android 2.3.5 with either sense 3/3.5 or aosp/aokp with Android 2.3.x.
Still no reply saying whether this method helps or not? Where did the testers go.
I have tried this method but the results are random. On sense roms it has no effect but on cm/aokp/pa it works for a few cycles but after playing a game for about an hour the phone will charge in your pocket
Sent from my HTC Desire HD using xda app-developers app
bondocel said:
I have tried this method but the results are random. On sense roms it has no effect but on cm/aokp/pa it works for a few cycles but after playing a game for about an hour the phone will charge in your pocket
Sent from my HTC Desire HD using xda app-developers app
Click to expand...
Click to collapse
This was fun!! Even I had the same experience
Phone: Desire HD
ROM: JellyTime_R31
Gonik said:
Well, after i tested almost every single ROM in the development section, there was a time that the battery behaved quite abnormal.
First when the phone was charging, many times it "jumped" from around 70% to 100%. While discharging with only WiFi open, it often drop from around 30% to 10-15% and then up again.
I tampered with the Governor setting, but it didn't improve much. But I did found something that somehow fixed the issue and improved the battery life quite a lot and also fixed the "jumps" while charging and discharging.
Backup whatever you need (SMS, Call Log, Bookmarks) from your favorite backup program
Download the Stock Rom Official RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1 , thanx to nitr00
Reboot in Recovery (CWM, 4EXT, whatever you use) and do a Factory Reset, Wipe Cache & Dalvik and Wipe Battery Stats
Flash the Official ROM you downloaded, reboot your phone and complete the Initial Setup.
Again, reboot in Recovery and do a Factory Reset, Wipe Cache & Dalvik
Flash your favorite ROM (clean install) and restore your program, settings and backups
All done :highfive:
I know that it's somehow strange method but it worked on my phone running IceColdSandwich v8.8 and on a friend's (had the same issues mentioned above) with PACman v16.1. I had no more "jumps" and the battery life improved significantly.
Since this is my first thread, i'd like to thank the fine community here in XDA for their work and efforts I really hope that the above advice help also other people.
Click to expand...
Click to collapse
poor trick doesn't work.
Battery Jump Issue
I did read this somewhere in this forum. I am not able to recollect it
Download the Battery Calibrator..
Download the Current Widget... and put a small widget in your screen which shows the amount of current being used from your battery.
Charge your Phone until the Current widget shows 0mA (Green Battery Full Indicator or 100% charge is not enough)
Open Battery Calibrator and then click on calibrate battery and then take it off the charger.
Let the phone discharge completely to 0% (It should power off by itself of no charge)
Then charge the phone completely on one go till the current widget shows 0mA
Now, your phone battery should be good Atleast, your Battery Jumps should be gone by now
You can search for similar post, if you are not satisfied with this there are other options people might suggest
Please dont forget to press "THANKS" if this post helped you
Phone: HTC Desire HD
ROM: Jellytime_R31
Battery Calibrator its work corectly!!

A7 horrible standby time, unusual RF signal drain, battery% drop 4% overnight(8hours)

I understand that bad signal will drain more battery but when I'm at home with perfect signal and wifi I still get pretty bad drain. I disabled wifi and set data to 2G over night and I left with 4% drain after 8 hours. I have no issue with wakelock, no Facebook, don't use snapchat often, super light user. Overall, very disappointed with the A7. I just can not stand the standby time, and I have no idea how to fix it. When I'm in school with bad signal, the battery drain even faster .Come from Iphone 5s which is almost a 3 years old phone(still work like charm, and my moms using it) with literally no battery drain overnight, and it out performance the A7 in battery life by far(with outstanding standby time). Just kindly ask you guys, do you have this kind of issue or is it just me? And any suggestion on fixing this issue?
here is the link for the battery screenshot, I'm a new user so I deleted the http
imgur.com/a/kcRDO
Did you disable the WiFi scanning? This is commonly a major factor in battery drain in Android phone.
Also, try to wipe the cache and dalvik
ttkian said:
Did you disable the WiFi scanning? This is commonly a major factor in battery drain in Android phone.
Also, try to wipe the cache and dalvik
Click to expand...
Click to collapse
No, sir wifi scannings on, is it the major battery hog? I know how to wipe cache but how do you wipe dalvik? Also do I have to disable location?
Badman™ said:
No, sir wifi scannings on, is it the major battery hog? I know how to wipe cache but how do you wipe dalvik? Also do I have to disable location?
Click to expand...
Click to collapse
In my experience, the WiFi scanning should be disable to help battery drain. Go to location, click the three dot on the top right hand side corner, click scanning, then turn off the WiFi scanning and bluetooth scanning.
You have to boot to recovery to wipe cache and dalvik. Turn off the phone. After it's off, press the volume up and hold it while you press the power button. Once the phone vibrates and ZTE logo is showing, release the power button but hold the volume up. You will be presented with recovery option. Choose wipe cache and dalvik, then reboot. Be very careful with this, don't click the wrong choice. I am not responsible if your phone is bricked because you did something wrong here. If you are not familiar with it, DON'T do it.
For location, I don't disable it, but I put it under "battery saving" mode. When I use navigation, I will change it to high accuracy.
Try the first one and the third ones and see what happens after a few days. If you are still not satisfied, wipe the cache and dalvik (DON'T do this if you are not familiar with it)
My personal experience with this phone, I can have 5 to 7 hours SOT depending on what I do.
ttkian said:
In my experience, the WiFi scanning should be disable to help battery drain. Go to location, click the three dot on the top right hand side corner, click scanning, then turn off the WiFi scanning and bluetooth scanning.
You have to boot to recovery to wipe cache and dalvik. Turn off the phone. After it's off, press the volume up and hold it while you press the power button. Once the phone vibrates and ZTE logo is showing, release the power button but hold the volume up. You will be presented with recovery option. Choose wipe cache and dalvik, then reboot. Be very careful with this, don't click the wrong choice. I am not responsible if your phone is bricked because you did something wrong here. If you are not familiar with it, DON'T do it.
For location, I don't disable it, but I put it under "battery saving" mode. When I use navigation, I will change it to high accuracy.
Try the first one and the third ones and see what happens after a few days. If you are still not satisfied, wipe the cache and dalvik (DON'T do this if you are not familiar with it)
My personal experience with this phone, I can have 5 to 7 hours SOT depending on what I do.
Click to expand...
Click to collapse
Good advices bro.
What firmware are you running?
nfsmw_gr said:
Good advices bro.
What firmware are you running?
Click to expand...
Click to collapse
I am running Bad Boyz 7.1.1 v1. 0 with Beast kernel v31.
ttkian said:
In my experience, the WiFi scanning should be disable to help battery drain. Go to location, click the three dot on the top right hand side corner, click scanning, then turn off the WiFi scanning and bluetooth scanning.
You have to boot to recovery to wipe cache and dalvik. Turn off the phone. After it's off, press the volume up and hold it while you press the power button. Once the phone vibrates and ZTE logo is showing, release the power button but hold the volume up. You will be presented with recovery option. Choose wipe cache and dalvik, then reboot. Be very careful with this, don't click the wrong choice. I am not responsible if your phone is bricked because you did something wrong here. If you are not familiar with it, DON'T do it.
For location, I don't disable it, but I put it under "battery saving" mode. When I use navigation, I will change it to high accuracy.
Try the first one and the third ones and see what happens after a few days. If you are still not satisfied, wipe the cache and dalvik (DON'T do this if you are not familiar with it)
My personal experience with this phone, I can have 5 to 7 hours SOT depending on what I do.
Click to expand...
Click to collapse
Thank you good sir, appreciate your advice! I'll try this and see what will happen
ttkian said:
In my experience, the WiFi scanning should be disable to help battery drain. Go to location, click the three dot on the top right hand side corner, click scanning, then turn off the WiFi scanning and bluetooth scanning.
You have to boot to recovery to wipe cache and dalvik. Turn off the phone. After it's off, press the volume up and hold it while you press the power button. Once the phone vibrates and ZTE logo is showing, release the power button but hold the volume up. You will be presented with recovery option. Choose wipe cache and dalvik, then reboot. Be very careful with this, don't click the wrong choice. I am not responsible if your phone is bricked because you did something wrong here. If you are not familiar with it, DON'T do it.
For location, I don't disable it, but I put it under "battery saving" mode. When I use navigation, I will change it to high accuracy.
Try the first one and the third ones and see what happens after a few days. If you are still not satisfied, wipe the cache and dalvik (DON'T do this if you are not familiar with it)
My personal experience with this phone, I can have 5 to 7 hours SOT depending on what I do.
Click to expand...
Click to collapse
The main issue is the RF signal and standby time drain huge percent of battery. Disabling wifi scanning will reduce the drain but only on wifi portion. there is the link of my screenshot I took after disabling wifi scanning and location. Did not fix battery drain on idle issue.
http://imgur.com/a/wRb4G
Badman™ said:
The main issue is the RF signal and standby time drain huge percent of battery. Disabling wifi scanning will reduce the drain but only on wifi portion. there is the link of my screenshot I took after disabling wifi scanning and location. Did not fix battery drain on idle issue.
http://imgur.com/a/wRb4G
Click to expand...
Click to collapse
If I look at the attachment, you use the phone for 13.5 hours since you charged it and you still have 78% of battery left. If that's the case, I don't see a problem with that.
The 41% of RF signal usage is out of your hardware battery usage (75%). So, in reality, it's 30% of usage which represents 6.6% of overall usage (30% x (100-78)%). It seems to me that you had the phone connected to wireless data during this time, not your WiFi? If so, that's normal.
I get 3% battery drain overnight at most.
Don't see any problem with that.
That SoT is with streaming movies etc. YouTube a little gameplay and Facebook.
chaki- said:
I get 3% battery drain overnight at most.
Don't see any problem with that.
That SoT is with streaming movies etc. YouTube a little gameplay and Facebook.
Click to expand...
Click to collapse
That's pretty good. I'm not getting that. I average 5 hours. Will see what the latest 7.1.1 gives me.
I mostly just surf the net and check emails so I should be getting more.
Hi, guys have any of you been able to solve this issue? I'm currently using stock 8.0 and I have just replaced my battery for a new one and still RF signal and Standy are killing my battery (even using airplane mode).
I don't know what to do. I have tried going back to android 7.1.1. and 6.0 with no luck. I have tried several factory resets, I have wiped cache, I just don't know what else to do. My phone's battery is simply dying for no apparent reason.
I will post some Gsam screenshots before my battery dies.
I will post the screenshots later on today. But I can say now there is a major problem with the standby of the phone. So I fully charged the device this morning and battery has dropped by 15% in 4 hours simply from standby (I haven't used the phone).
---------- Post added at 01:15 PM ---------- Previous post was at 12:52 PM ----------
My problems keep getting worse. Now I'm stuck in FTM mode and I can't get out. I have tried every single combination of buttons for way over 10 seconds with no luck.I guess I will have to wait until the baterry dies and hope for the best.
Something went finally the right way! After several attemps I have been able to reboot the phone via the "adb reboot" command while stuck in FTM mode.
Back to figuring out what to do to improve the phone's battery. While stuck in FTM mode the battery went from 80% to 60% (screen was on obviously in FTM mode) - 4 hours aprox.

Resources