Hero dropped into the toilet :( - Hero, G2 Touch General

Hello,
today i accidently dropped my Hero into my toilet (no joke!)
I pulled it out and dried it and immediately turned off and removed the battery. I tried drying it with a hair fan and am waiting now but I am scared to turn it on again (happened like 7 hours ago...)
Do you think it's broken?

put it in a air tight container with some silicon granuals u get from paking or a load of raice and leave it some were warm for a few days b4 u try a battery in it

I don't think its alive, but before turning it on let is for 3-5 days inside a bowl of rise, so all water will be dry from the motherboard. Remove battery , cover , sd card and let the rise do its job.
I hope you get your phone fixed by that trick

I did this recently with my hero, but instead it was the bath.
First thing I done was take out the battery.
I then put the phone in a plastic container without the back cover or battery and covered with rice.
I then put this on top of a radiator and left it for 3 days.
This worked for me thank god. The phone is now cleaner then ever , only downside the watermarks are now red so no warranty for me.
I hope you have similar luck.

Thanks alot, I'll try the rice trick for now.

dr_lovejoy said:
...only downside the watermarks are now red so no warranty for me.
Click to expand...
Click to collapse
I'm sure it wouldn't be too hard to source three of '77H00668-00M' if you knew where you were looking. I can tell you that there are three of those waterproof stickers in the phone, and only one is visible from the outside. The other ones are located internally, one at the radio on the bottom surface, and the other at the top right, near the earpiece (all on the rear of the phone with the screen facing down). There's also one tamper-proof 'VOID' label to contend with, part number '77H00615-01P'.
For informational purposes only I do not condone 'warranty fraud'!

@anon2121
great advice if i only knew i how to put it in action, by warranty sticker are fooked, dropped apple juice on my hero

@fwers
Unfortunately that's the bit I can't help you with
Would you happen to have a similar old HTC device that uses those same stickers? If so, if it's out of warranty, a transplant of water-evident stickers (carefully so as not to damage them) may be possible. The 'VOID' tamper-proof one is slightly harder though, and you may need to just find a way to remove it without 'triggering' it. Usually, it is possible to remove these tamper-evident seals without damaging them, so long as you are slow and careful, and know what to do.
HTH

Hello again,
two days later i reassembled my phone - leaving it in a bowl of rice near the heating - and... it works again absolutely flawlessly
Thanks alot!

Question, did you flush before you dropped it in?

barryallott said:
Question, did you flush before you dropped it in?
Click to expand...
Click to collapse
lol; what a funny question :-D I really hope u did or that u dropped it into some alcohol after that to get it "clean" ;-)

iRobert said:
lol; what a funny question :-D I really hope u did or that u dropped it into some alcohol after that to get it "clean" ;-)
Click to expand...
Click to collapse
oh.. yes.. do clean.. bio hazard!!!
And dont eat the rice!!!!
LOL

iRobert said:
lol; what a funny question :-D I really hope u did or that u dropped it into some alcohol after that to get it "clean" ;-)
Click to expand...
Click to collapse
Yeah, well I still got a white Hero...

Nemo0815 said:
Yeah, well I still got a white Hero...
Click to expand...
Click to collapse
It's still white? From what I've heard about that teflon coating, yours must be yellow now! Or even brown!!!!11one

pauliusba said:
It's still white? From what I've heard about that teflon coating, yours must be yellow now! Or even brown!!!!11one
Click to expand...
Click to collapse
Well, that sorta killed the topic..

If it helps anyone else,
I wrote a seven step article to dealing with this in the future
http://tech-n-life.com/index.php/2010/02/7-steps-to-save-your-phone-if-it-gets-water-damaged/

Open the phone.
Get a 100Ml bottle of IPA(Iso Propyl Alcohol) or Spirit.
Dip the tooth brush in the IPA and clean the board throughly.
Then blow it dry using the hair drier.

Related

Water and HD2...

So I got some water into my HD2 and it's been sitting in rice and now silica gel for about 2 whole days now. Seems it's dried out around the circuitry (the screen doesn't flicker anymore and the touch screen is 100% functional). My problem is, I can see water under my screen. It is a pretty large amount of water under the screen as I can see discoloration (like water on paper sort of discoloration) and when I press the screen water bubbles move.
I'm relieved that the phone turns on and it functions 100% it's just there's so much water trapped under the screen.
Can anyone help me out and tell me how to disassemble just the screen so the water can get out? If that's too difficult, does anyone know how long it would take (ballpark estimate) for the water to come out. I'm paranoid because I think about a water bottle with a bit of water in it and that if it is sealed the water doesn't evaporate and just stays in there. Would that apply for my phone because it is sealed up? I mean the water got in there somehow so there must be some holes/gaps that will allow the water to evaporate out of (screen isn't foggy or anything though) but I'm afraid if the water stays in there too long it might do extra damage?
Sorry for this long novel, but any help or advice would be great. Thanks in advance.
a4_h23 said:
So I got some water into my HD2 and it's been sitting in rice and now silica gel for about 2 whole days now. Seems it's dried out around the circuitry (the screen doesn't flicker anymore and the touch screen is 100% functional). My problem is, I can see water under my screen. It is a pretty large amount of water under the screen as I can see discoloration (like water on paper sort of discoloration) and when I press the screen water bubbles move.
I'm relieved that the phone turns on and it functions 100% it's just there's so much water trapped under the screen.
Can anyone help me out and tell me how to disassemble just the screen so the water can get out? If that's too difficult, does anyone know how long it would take (ballpark estimate) for the water to come out. I'm paranoid because I think about a water bottle with a bit of water in it and that if it is sealed the water doesn't evaporate and just stays in there. Would that apply for my phone because it is sealed up? I mean the water got in there somehow so there must be some holes/gaps that will allow the water to evaporate out of (screen isn't foggy or anything though) but I'm afraid if the water stays in there too long it might do extra damage?
Sorry for this long novel, but any help or advice would be great. Thanks in advance.
Click to expand...
Click to collapse
HERE is a video to disassemble the HD 2 Hope it helps. I just found the video so please be carefull
zelendel said:
HERE is a video to disassemble the HD 2 Hope it helps. I just found the video so please be carefull
Click to expand...
Click to collapse
Yeah I saw that too. Thing is, I'm terrified to try. That and I lack the tools to do so and even if I were to buy the tools, I have yet to find a video on how to just do the screen as I don't want to take the whole phone apart. It looks as if you might have to take the whole thing apart, but I was hoping there was an easier way to remove the screen
a4_h23 said:
Yeah I saw that too. Thing is, I'm terrified to try. That and I lack the tools to do so and even if I were to buy the tools, I have yet to find a video on how to just do the screen as I don't want to take the whole phone apart. It looks as if you might have to take the whole thing apart, but I was hoping there was an easier way to remove the screen
Click to expand...
Click to collapse
From what I saw on the video I dont think you can just remove the screen. I have not gotten the nerve up to do it myself either
On a side note, leaving the phone horizontel in the silica gel/rice for about 3 days may work also. Did on an old sansa mp3 player of mine. Let gravity help?
rickyzone said:
On a side note, leaving the phone horizontel in the silica gel/rice for about 3 days may work also. Did on an old sansa mp3 player of mine. Let gravity help?
Click to expand...
Click to collapse
Do you mean like on its side? I didnt think of that... Its been flat on its back. Great advice! Thanks! Ill check back in 4 days to update.
Hopefully you haven't taken it apart yet. I got water under my screen too (from installing a knockoff brand of an invisible shield) had the discoloration.etc and so I put it in a container of rice for about a week. after 99% of it had gone away I stuck it under a lamp for an hour (make sure to not put it too close so you don't melt anything) and now it looks and runs just fine. Plus this way my warranty isn't void still (sticker on the back is white.etc)
Ahanix said:
Hopefully you haven't taken it apart yet. I got water under my screen too (from installing a knockoff brand of an invisible shield) had the discoloration.etc and so I put it in a container of rice for about a week. after 99% of it had gone away I stuck it under a lamp for an hour (make sure to not put it too close so you don't melt anything) and now it looks and runs just fine. Plus this way my warranty isn't void still (sticker on the back is white.etc)
Click to expand...
Click to collapse
That's really great news. I wouldn't dare to take it apart. I was hoping to hear from someone who has had the same thing happen before and have had good results. So about a week then would be a good time to leave it. It has been sitting in silica gel for about 3 days now (and rice before that for a day) so I'm gonna check up on it in two or three days. Was it a lot of water under your screen? Cuz mine looks like a lot.
My indicator actually showed water damage but I bleached it back to white lol (hell I don't have insurance nor will I be turning it in to T-Mobile anyhow) because the red is ugly. Anyway thanks for stopping by to let me know, it feels really good for me now because I've been worried sick for these past few days!
Hello (Sorry for my english), I have similar problem. Today I try place screen protector via wet method and now I have display full of water and my hd2 is in the box of rice.
For all that hd2 is fully functional. I hope it will be not very long procedure.
ameron said:
Hello (Sorry for my english), I have similar problem. Today I try place screen protector via wet method and now I have display full of water and my hd2 is in the box of rice.
For all that hd2 is fully functional. I hope it will be not very long procedure.
Click to expand...
Click to collapse
It took mine about a week to dry out about 95%. Hopefully yours turned out/will turn out alright too.

My wildfire is dead! :(

I ****ed up today!!! Forgot to empty my pockets and now my wildfire is in the washinmachine! Couldnt stop the f-ckin machine and watched my clothes in a 60min-programe. When finally the program was finished, the stupid lid could not open. And I were in a hurry to get to my workingplace. Now the wildfire is in the washingmachine until I come home.
Probably the phone is as dead as Michael Jacksson!
Is there any way maybe to rescue my phone after this treatment? Hairfan? Oven? Element for drying?...something?
I really like this wildfireforum and you guys writing here, so want my phone back!
Akerhage said:
I ****ed up today!!! Forgot to empty my pockets and now my wildfire is in the washinmachine! Couldnt stop the f-ckin machine and watched my clothes in a 60min-programe. When finally the program was finished, the stupid lid could not open. And I were in a hurry to get to my workingplace. Now the wildfire is in the washingmachine until I come home.
Probably the phone is as dead as Michael Jacksson!
Is there any way maybe to rescue my phone after this treatment? Hairfan? Oven? Element for drying?...something?
I really like this wildfireforum and you guys writing here, so want my phone back!
Click to expand...
Click to collapse
Put of Battery and place it at a heating. put between them a paper cloth!
Wait a few days and pray
Deep-Knight said:
Put of Battery and place it at a heating. put between them a paper cloth!
Wait a few days and pray
Click to expand...
Click to collapse
should I only put the battery on the heatingelement? or the whole phone?
Should I maybe wash it in water first to get rid of eventually rests from the machine? (sorry for my swedish-english writing here;p)
Ouch, nasty. After a full cycle in the washer I wouldn't hold much hope but it is worth trying the old rice trick.
Take the battery out of the phone and put the phone in to a bowl (or bag) of UNCOOKED rice (it doesnt really work if the rice is cooked lol) and leave it overnight. The dry rice soaks all moisture out of the phone making sure it is completely dry without heating it up (and possibly damaging it more).
http://hacknmod.com/hack/diy-save-a-wet-cell-phone-using-rice/
This is what happened to my sony phone lol, except I left it overnight in the wash.
kevin2516 said:
This is what happened to my sony phone lol, except I left it overnight in the wash.
Click to expand...
Click to collapse
I had a SE W995 before and took a shower with that one, therefore I bought this one...I really think I should awoid water for the rest of my life!!
Will try the radiator l8er!!
Akerhage said:
should I only put the battery on the heatingelement? or the whole phone?
Should I maybe wash it in water first to get rid of eventually rests from the machine? (sorry for my swedish-english writing here;p)
Click to expand...
Click to collapse
the whole phone without battery. rice idea sound also good. but wait a few days ,not only a few hours.
Deep-Knight said:
the whole phone without battery. rice idea sound also good. but wait a few days ,not only a few hours.
Click to expand...
Click to collapse
I will wait until monday, hoping for the survival of my dear wildfire!
Akerhage said:
Will try the radiator l8er!!
Click to expand...
Click to collapse
I wouldn't use a radiator! Just the heat alone could kill your phone.
Hpez said:
I wouldn't use a radiator! Just the heat alone could kill your phone.
Click to expand...
Click to collapse
Okay, should I just let it be in roomtemperature then?
Akerhage said:
Okay, should I just let it be in roomtemperature then?
Click to expand...
Click to collapse
Just put the phone in a bowl of dry rice at room temperature and leave it overnight, or maybe even a day or so. The rice will pull the water out of the phone without any need for heat.
should I just put the phone on the rice or put the rise under and over the phone? So that the phone is covered on all sides, lying in the middle of the bowl?
Akerhage said:
should I just put the phone on the rice or put the rise under and over the phone? So that the phone is covered on all sides, lying in the middle of the bowl?
Click to expand...
Click to collapse
Put it in the rice, so it is completely covered.
Hpez said:
Put it in the rice, so it is completely covered.
Click to expand...
Click to collapse
sweet, will try that when I come home then =)
Or you take pure alcohol and soak it
(few hours, but very IMPORTANT >99% purity !)
Afterwards dry it for several days <-- do not heat it, just dry it
Disclaimer: Works since it is pure simple chemistry, but I never dared to do it so far
If the rice method doesn't work, and if you got some experience in electronics, try opening your phone up and look if any vital components are harmed...
ebioman said:
Or you take pure alcohol and soak it
Disclaimer: Should work, but I never dared to do it so far
Click to expand...
Click to collapse
Will try the rice first, sounds less risky
The only problem with soaking in alcohol is that it can dissolve any glues used within the phone itself. But if nothing else works it might be worth trying as a very last resort.
Seriously it will not do any harm as long as you really use 99% + purity.
The problem is remaining humidity leading to oxidation (corrision) of your contacts. Alcohol is a solvent and therefore water free. It will "take up" the humidity and afterwards evaporate.
I guess the major problem is that exept for me not a lot of people here work in a laboratory and have easy acess to a liter of 99,99% pure alcohol.....
isnt there anything called batterywater? Maybe that workes? Think I can buy that on statoil and similar places?

Vibrant went into the washing machine........

Update 3/2/11. I cleaned the phone with the cleaner posted in this thread. Got all the soap residue off no problem and dried very quickly. Got the spare battery out and tried the phone...nothing. It doesn't even try to turn on. I did get my data off the external SD. I really wish I could get the data off the internal SD as it has most of what I want like a bunch of photos and stuff. Oh well. Thanks for the tips in this thread.
Original post.
What are the odds it will be ok?
What are the odds I'll at least be able to recover data off my external sd card? I have nandroid backups on it if I have to get a new phone.
Whole story.
I got in the shower my pants (with the phone in the pocket) got picked up by my girlfriend who thought she would help out and wash them with some other laundry. The phone went through all but the spin cycle before I got it out.
The phone was on when it went in and off when it came out. I pulled the battery and dissembled the phone. It is now in pieces drying out.
It looks like the underside of the main board (the metal casing holding the parts) has some discoloration, its sorta blackened and maybe has soap residue on it as well.
Anyway....this sucks.
Edit: Got the phone parts in rice. Hoping to at least get it working long enough to get my data/photos off of it.
Back in my Blackberry days there were always stories of people dropping there phones in water and it surviving.
They would take the phone apart and put it in a container of rice for a few days to absorb all the water. Problem is it was always said that pulling the battery immediately after it got wet was key. Since your phone was under for an extended period of time I dunno if this would work for you but its worth a try.
regP said:
Since your phone was under for an extended period of time I dunno if this would work for you but its worth a try.
Click to expand...
Click to collapse
That's what I'm wondering too. Usually it's dropped in water for a few seconds, hardly time for the water to seep in and the battery can be pulled before the phone even shuts down. Mine was totally soaked.
Yeah... The outlook is kind of bleak but since its such an expensive device and a bag of rice is really cheap give it a shot.. Never know!
yeah, i've had that same thing happen with a phone and my zune (get in shower with phone/zune still in pants pocket...). when my phone went through the wash it was non functional, when my zune went through the wash it dried and has worked just as well for years.
how common is it to take a shower with pants on? Am I the only weirdo that takes showers without pants? Whats going on lol
I think the best way is to put it on the drier.
ferhanmm said:
how common is it to take a shower with pants on? Am I the only weirdo that takes showers without pants? Whats going on lol
Click to expand...
Click to collapse
Lol that's exactly what I was thinking.
Sent from my SGH-T959 using XDA Premium App
one good thing is you can probably( dont know if this is still true) find a vibrant for very cheap.. as people have been dumping them left and right.
joshthewaster said:
I got in the shower my pants (with the phone in the pocket) got picked up by my girlfriend who thought she would help out and wash them with some other laundry.
Click to expand...
Click to collapse
A great example of how important a comma can be
Put it in a jar of rice... this is a must do.
Its days are numbered.
If your phone was submerged in soapy water for a rinse cycle, then this is what will probably happen:
• If you take it apart some and dry it out (heat, bag of rice, etc) completely for a day or two and then put it back together, it will probably work fine at first.
• Over the next few weeks, it will start to break down as circuit traces and contacts corrode
I would highly recommend purchasing a Motorola Defy (waterproof), which should be able to withstand a wash cycle.
Also, find a girlfriend who isn't so absent minded. Anyone who has EVER worn pants and done laundry should think to go through the pockets before they toss them in a washing machine. Hell, I check mine twice..... once before i toss them in the hamper and then again right before I toss them in the machine.
Tarzanman said:
• Over the next few weeks, it will start to break down as circuit traces and contacts corrode
Even this would be ok. My contract with tmobile ends in a month so if I can make it to there.
Also, find a girlfriend who isn't so absent minded. Anyone who has EVER worn pants and done laundry should think to go through the pockets before they toss them in a washing machine.
Click to expand...
Click to collapse
To be fair I don't ever check pockets I just don't leave stuff in them. And those jeans were going back on when I was getting out of the shower.
Dropped mine in the toilet. Just let it dry, everything should be fine. At first you'll probably panic and ****'ll look like its ****ed up. But after it's dry everything should be functional. Now for the beating it might've taken... I'm not sure, but my daughter(infant) and I have this vibrant dropping/slamming/throwing fetish and the phone has survived that, so you should be fine .
hazard99 said:
one good thing is you can probably( dont know if this is still true) find a vibrant for very cheap.. as people have been dumping them left and right.
Click to expand...
Click to collapse
This is true. I was very happy with mine but thought that since this happened I would maybe at least look at other options, possibly a vibrant 4G.
ferhanmm said:
how common is it to take a shower with pants on? Am I the only weirdo that takes showers without pants? Whats going on lol
Click to expand...
Click to collapse
Sorry man, I'd be so pissed if my Vibrant ended up in the washer. However, I can't stop laughing about this comment.
If you have access to chemicals, you can also toss it in concentrated alcohol. That will for sure remove the water and make it dry faster. It would probably help dissolve any soap residue as well. Probably won't be good for the adhesives used on the phone, but those are just used to tack down some things like the button lights and such. The rest are really held down w/ screws.
vnamee said:
If you have access to chemicals, you can also toss it in concentrated alcohol. That will for sure remove the water and make it dry faster. It would probably help dissolve any soap residue as well. Probably won't be good for the adhesives used on the phone, but those are just used to tack down some things like the button lights and such. The rest are really held down w/ screws.
Click to expand...
Click to collapse
Huh, interesting idea. Has this been done? Don't really want to be the guinea pig but I'm tempted.
Don't forget to set it on perm press and add the sheets! Lol!
iynfynity said:
I think the best way is to put it on the drier.
Click to expand...
Click to collapse
Rockin that Bionix V 1.3 w/ Androdena 5.2
Same thing happened to me just two weeks ago. Went through a full wash rinse cycle. But it never recovered. Power came back, but the screen was stuck in download mode and had heavy banding throughout the screen. My PC couldn't recognize the phone despite it being in download mode.
My mistake was trying to turn it on while it was still wet. I was completely ignorant about how to handle wet phones, and tried desperately to turn it on. Rice after one week did nothing to it... I think the damage was already done.
Hopefully with lots and lots of patience, you'll be able to get your phone back.
insurance ftw
Don't wash your jeans, crisis averted

Phone fell in water

Still works but the screen is foggy and flickers alot.
A friend of mine was telling me that something in the batter triggers and sprint can tell if it had water damage or not. How can i tell and look for that?
I also want to take it in but dont want sprint finding out about the water damage. Is there a loophole?
Shifted from my EVO
Well first things first. Turn it off, pull the battery. Do not try to restart it. You have several choices to dry it out. One really and proven one is rice. Fill a container half way with rice. Then stick your phone in the rice with the battery out, and the cover off. Push it down into the rice, and let it stay there for at least two days in a warm dry place. The other was actually used by a member here on XDA. He used is a Dehydrator. Not sure of the details, but it definately worked. I'd say set it on low and leave it there for at least 24hrs. Sprint can tell if the phone has been dropped in water by checking the water damage indicators. On the phone itself, and the battery. They're Red checkered squares. They turn bright Red when dropped in water. Although it has been proven they're not very reliable.
^^ is correct about the indicator on the battery. Its a little sticker and i always pull it off and take it to them. Once they asked me about the sticker and i just told them i have no idea what your talking about and that i didn't know about any sticker. Playing dumb helps
Take battery out....Stick it in oven on warm heat...take it out after 10 minutes to let it cool down.....repeat like 4 times.....
Sounds freaky but i fixed an iPod Touch and a Droid X with this method
Thanks for the replies guys. I ended up using a hair dryer on heat. It's not that bad of a condition. Everything seems to work properly (so far). This would happen when a ICS beta ROM comes to our phones... -_-
is there any other indications that sprint would be able to tell if it had water damage?
Enraged21 said:
is there any other indications that sprint would be able to tell if it had water damage?
Click to expand...
Click to collapse
Nope, unless there is still water in it when you take it there, oh and don't use a hair dryer, all that does is "push" water in deeper through all the electrical wiring and circuits, plus it can melt parts of the device
Personal expierence lol
notsointeresting said:
Nope, unless there is still water in it when you take it there, oh and don't use a hair dryer, all that does is "push" water in deeper through all the electrical wiring and circuits, plus it can melt parts of the device
Personal expierence lol
Click to expand...
Click to collapse
+1 to not using the hairdryer . It will not work as well as you think. There's a good chance that you still have moisture in the device.
See I wouldn't have known that lol. Thankss!
Why we're here.

Enegry drink + tf101 = A bad situation

Hey everyone
My poor transformer has seen better days, here's the deal
I had a can of energy drink in my bag and it decided to open its self and left a puddle of liquid at the bottom of it, sadly that's where my transformer was. after a few hours of drying with a hair dryer I turned it on and surprisingly it turned on and is working fine other than the left hand side of the screen is now brighter the then the right (here's a picture of the screen https://www.dropbox.com/s/ci6m1y4abh8n0z6/IMG_20120731_113759.jpg). I rung asus and apparently gonna cost $300 + nz because they only replace the whole LCD panel which is far to much. touchscreen, volume rocker(volume rocker side got wet) etc all work fine (Im typing this off it now). Just want to know if anyone has any ideas about fixing it .
Cheers
Almost looks like it's still not dry yet you should have put it in a zip lock bag with rice right away
xstokerx said:
Almost looks like it's still not dry yet you should have put it in a zip lock bag with rice right away
Click to expand...
Click to collapse
If i had enough rice i would lol, Its been sitting under a heat pump for a few hours and nothing has changed with the screen . Im a complete noob with lcd's but it almost looks like drink has reacted with some layer on the lcd, its gone slightly transparent down the bottom of the screen where the back lighting is. heres a better photo: https://www.dropbox.com/s/srhe70sumk34e63/IMG_0241.JPG
cheers
JoinTheRealms said:
If i had enough rice i would lol, Its been sitting under a heat pump for a few hours and nothing has changed with the screen . Im a complete noob with lcd's but it almost looks like drink has reacted with some layer on the lcd, its gone slightly transparent down the bottom of the screen where the back lighting is. heres a better photo: https://www.dropbox.com/s/srhe70sumk34e63/IMG_0241.JPG
cheers
Click to expand...
Click to collapse
You should have waited for few days before you turned it on... hair drier will dry out the moisture from outside, so what about inside ? So turn it off and let it dry out..... also don't over heat it, you might melt the plastic
Sent from my Transformer TF101 using xda app-developers app
udupa82 said:
You should have waited for few days before you turned it on... hair drier will dry out the moisture from outside, so what about inside ? So turn it off and let it dry out..... also don't over heat it, you might melt the plastic
Sent from my Transformer TF101 using xda app-developers app
Click to expand...
Click to collapse
lol i accidently turned it on trying to get the bezel off, then stripped the screw so now its gonna be a mission trying to get it open lol , i thought i had killed it when i saw it booting up but I left it and it's working fine so far i thought if i leave it running it might start drying it out internally. Im gonna probably try claim insurance on it so anythings worth a try atm lol
Is it worth claiming insurance (then getting an insurance raise) vs getting a new one if it is broken? Good luck, I wouldn't dry it with heat... just soak it in rice because the rice will soak it up..
asdfuogh said:
Is it worth claiming insurance (then getting an insurance raise) vs getting a new one if it is broken? Good luck, I wouldn't dry it with heat... just soak it in rice because the rice will soak it up..
Click to expand...
Click to collapse
Yeah gonna see how much excess etc will cost first,hair dry was making slight progress which is good but i'm trying the method here (http://chathuraw.wordpress.com/2009/04/16/rescuing-a-water-damaged-laptop-display/) hopefully ill see some results, id do the rice method but i believe only a small amount of liquid managed to get in, there just seems to be a bit of moisture on the back of the LCD panel.
Definitely try and get it open, possibly give it a rinse. The sugar and crap in the energy drink would eat away at bits you don't want to be eaten away.
If you were in Dunedin I'd do it for you, had my 101 open a few times, and recovered lots of stuff that's had **** spilled on it
neoprint said:
Definitely try and get it open, possibly give it a rinse. The sugar and crap in the energy drink would eat away at bits you don't want to be eaten away.
If you were in Dunedin I'd do it for you, had my 101 open a few times, and recovered lots of stuff that's had **** spilled on it
Click to expand...
Click to collapse
Cheers man , I got one of the screws out but the other is starting to strip so i want find a proper sized Allen key before i ruin it completely lol, Is there anything specific you would recommend rinsing it with?
JoinTheRealms said:
Cheers man , I got one of the screws out but the other is starting to strip so i want find a proper sized Allen key before i ruin it completely lol, Is there anything specific you would recommend rinsing it with?
Click to expand...
Click to collapse
Distilled water if you can find it. Bottled water at a pinch. Under no circumstances use Christchurch tap water
neoprint said:
Distilled water if you can find it. Bottled water at a pinch. Under no circumstances use Christchurch tap water
Click to expand...
Click to collapse
Sweet as, ill see how insurance goes, if its not worth it ill rip it open and give it a clean. Cheers
Well you could try it with alcohol. I do it quite often with water damaged phones.
You turn the pad off open your TF101 - here I have to mention that I have never open a Transformer so I can't help you with that - if possible you remove the battery, protect the display and brush the damaged parts with something high in alcohol content (my drugstore has a 98% ethanol)
The idea with distilled water can help sometimes but I experienced often that it just worsen sharply
ProxiStyx said:
Well you could try it with alcohol. I do it quite often with water damaged phones.
You turn the pad off open your TF101 - here I have to mention that I have never open a Transformer so I can't help you with that - if possible you remove the battery, protect the display and brush the damaged parts with something high in alcohol content (my drugstore has a 98% ethanol)
The idea with distilled water can help sometimes but I experienced often that it just worsen sharply
Click to expand...
Click to collapse
Ive been looking at exploded pictures of the tf101 and I dont think it would have managed to get into the circiuty but ill open it up just to make sure. I was thinking rubbing alcohol might do the job, im waiting for the screen to return to normal its about 50% better then it was which is good, once that's back to normal im gonna try get it open, its a mission because i was panicking trying to get it open when i first done it and i threaded the screw so i gonna try super glue an allen key to the screw and try to get it out like that lol
Cheers

Categories

Resources