I just got a Cingular 8525. Is anyone having an issue with signal loss when going from an area with 3g coverage to edge coverage? My 8525 looses it phone and data service and must be manually reconnected by turning off the phone and then turning it back on. Is there a way to keep the device in edge mode only until cingular has more 3g coverage?
Do you have one of the new 3G SIM's to go with it? The ones with the flames and the 3G logo? I was having similar problems with my TyTN until I upgraded it to the Cingular ROM and got the new SIM. All better now.
i also have no problems and have the white sim with the flaming 3g logo, although i did run into a problem today, i was on a call, i went from U to G seamlessly, however when i returned to the 3g area (still on the same call) my call dropped and so did my signal, when it came back i was on U... i thought it was suppose to hold the call in G till the call was over, then come back to U...
Is anyone else having issues where the network keeps dropping or not connecting to 3g some times?
Nope I have a G1, so does my wife. and if I set her g1 next to my nexus one g1 will have 3g and nexus will have edge. We have very weak 3g coverage at our house. Then at work where I only get edge I do the same thing,m and my edge keeps dropping.
try to reboot the phone
yeah I have, I am wondering if its this phone, or the radio it uses.
Looks like I am not the only one with this issue.
http://www.google.com/support/forum/p/Google+Mobile/thread?tid=0bd8ccd4799040c2&hl=en&fid=0bd8ccd4799040c200047c994b22f4dd
I got my G2 a couple days ago and I must say this phone is amazing..coming from a g1 I had for 2 years its quite an improvement. The only minor problem I'm experiencing is with the radio signal..most notably in my house..on my G1 I always had signal and internet connection. Now with the G2 I constantly loose connection all through out the house and the only way to get it back is to switch the airplane mode on and off and it picks it up right away, only to go away a few minutes later..I don't seem to have the problem anywhere else.
Was wondering if any of you guys can shed some light on if there is a way for me to figure out why the signal is so random in my house and it was ok with the G1. And why airplane mode seem to fix it for a short while.
Sent from my T-Mobile G2 using XDA App
I have the same issue, I disable/enable wifi to get reception back on...I initially had really good reception but as the days went by my reception varies a lot at my house
Sent from my T-Mobile G2 using XDA App
JonathanFermin said:
I got my G2 a couple days ago and I must say this phone is amazing..coming from a g1 I had for 2 years its quite an improvement. The only minor problem I'm experiencing is with the radio signal..most notably in my house..on my G1 I always had signal and internet connection. Now with the G2 I constantly loose connection all through out the house and the only way to get it back is to switch the airplane mode on and off and it picks it up right away, only to go away a few minutes later..I don't seem to have the problem anywhere else.
Was wondering if any of you guys can shed some light on if there is a way for me to figure out why the signal is so random in my house and it was ok with the G1. And why airplane mode seem to fix it for a short while.
Sent from my T-Mobile G2 using XDA App
Click to expand...
Click to collapse
did u activate the sim card that came with the phone or still using the old one?
I'm still using the "old" one still but considering I got it 2 months ago I wouldn't think its a big deal unless the sim that comes with the G2 is any different?
Sent from my T-Mobile G2 using XDA App
JonathanFermin said:
I'm still using the "old" one still but considering I got it 2 months ago I wouldn't think its a big deal unless the sim that comes with the G2 is any different?
Sent from my T-Mobile G2 using XDA App
Click to expand...
Click to collapse
I asked because i was told to activate the new sim card to avoid issues likes the ones u seem to be having.
I was told to replace the sim card as well. After doing so there was no change in the reception of the unit. The downside is that the sim card does fine in my Vibrant but does not work at all in My Nexus One. Tried two different new sim cards and each time the Nexus One refuses tacknowledge it while the G2 and Vibrant do. I have found no difference in signal quality or strength with the new sim. The new sim card has a much smaller gold contact area and that area is a slightly different shape,
I went ahead and activated my new sim card to see if maybe it'll fix the problem..ill let you guys know how it goes
Sent from my T-Mobile G2 using XDA App
Changing the simcards will not work. If I put my simcard in my iPhone 3G or my G1, I'll have 2 or 3 bard with 3G, but with the G2, It switches up all the time, from Edge to 3G or no data at all, with 1 or 2 bars. I also have five other family members that also have T-Mobile phones and their getting about 4-5 bars on their phones. So it's not the sim or a tower issue.
There's cleary a problem with these phones.
This mourning I woke up and found the phone with no service, no bars. I reset it and came back, this afternoon I left the phone on my bed, came back to it, and again no service, it seems the service keeps going out for no reason.
Another is, I live in a big building, when walking in and out the building, my data connection will drop, or sometimes I won't even have any service, and again the only remedy is to restart the phone to get service back, airplane mode won't even fix it.
Yea the new sim hasn't really fixed anything at all..
Sent from my T-Mobile G2 using XDA App
JonathanFermin said:
Yea the new sim hasn't really fixed anything at all..
Sent from my T-Mobile G2 using XDA App
Click to expand...
Click to collapse
damn i was about to try that... guess i'll keep waiting... maybe an OTA radio update will help this cause it's really getting annoying.
I don't have a problem with my G2 dropping signal completely, but I have noticed that my 3G is very spotty. It's probably because I was spoiled the the MyTouch Slide's 3G only option.
Yes, I've noticed that the signal isn't quite as good as my G1. It's seems to be about on par, if not slightly below my friend's Vibrant.
But remember, the G1's radio really sucked once upon a time. Radio updates. They will come. Every phone that has OTA updates always gets new radio, in my experience.
I'm on my 3rd G2, mostly for manipulating the purchase price, and have noticed on this 3rd one that the spring is looser than the first two, the phone resets itself and often, and I'll loose data even though it shows I'm connected. This will happen in edge or hspda. I'm taking the phone back tomorrow.
Crappy thing I just put the ZAGG complete invisi shield on it. WIll Zagg comp me another cover you think?
If only Tmobile would activate the UMA calling over wifi. This would be the perfect phone with perfect service.
I am going to call tmobile in the morning and see if I can get any word on the UMA release. If not, the phone may have to go back.
I'm having the same problem, not at my house but at a local ihop that happens to be walking distance from where I'm moving in a week. I tried a reboot, airplane mode, even pulled the sim card and nothing worked. I got signal back once I left, but since it's right by the new place I would like to not have to deal with this.
Sent from my T-Mobile G2 using XDA App
well ive been searching around and i think ive found something that could help..
if you dial *#*#4636#*#* you will get a little screen of information about your phone, go to phone information, under phone information scroll down until you see select network type, the network should be automatically set to "WCDMA preferred" ive been playing around and i set mine to GSM/CDMA auto (PRL) and since then (about an hour roughly now) i havent lost my signal or connection in the same spot i was loosing it in my house every 10 minutes or so. not sure if this fixed anything but so far so good. definately will let you guys know if it continues to be good or if it doesnt stay consistent.
heres some information also in case you dont know which one would be best for you.
WCDMA preferred - The GSM phone is capable of using both 2G and 3G data communication and when signal strength is low 3G is favored more.
GSM only - The GSM phone is capable of using only 2G data communication. When the 2G signal is too low you get nothing at all.
WCDMA only - The GSM phone is capable of using only 3G data communication. When the 3G signal is too low you get nothing at all.
GSM auto (PRL) - The GSM phone is capable of using both 2G and 3G data communication and when signal strength is low 2G is favored more. This one is a bit confusing to me since PRL is associated mostly with CDMA technology and not GSM technology.
CDMA auto (PRL) - The CDMA phone is capable of using both 2G and 3G data communication and when signal strength is low 2G is favored more.
CDMA only - The CDMA phone is capable of using only 2G data communication. When the 2G signal is too low you get nothing at all.
EvDo only - The CDMA phone is capable of using only 3G data communication. When the 3G signal is too low you get nothing at all.
GSM/CDMA auto (PRL) - Some phones are equipped with both GSM and CDMA capabilities. This setting appears to just have the phone attempt to stay connected to the data communication type that works the best. (Maybe the Samsung Galaxy S will take advantage of this???)
Unknown - If none of the above fit or the phone is acting weird as far as connecting to the carrier, you will see your preferred network type is set to this
source- http://www.google.ie/support/forum/p/android/thread?tid=6a327a95211ac789&hl=en
Having same issue with the signal. Swapped for a new sim but still the same. Sometimes service drops completely and I have to go through the settings menu to search for a signal in order to get some reception
Sent from my T-Mobile G2 using XDA App
phone came in wcdma preferred stock... I came by that option too but I would much rather suffer with spotty signal [HSPA] over Slow edge speeds...
that said I may turn on GSM only when I'm indoors with little coverage, should save a lot of battery.
is there a setting that forces the G2 to go for the G3 or H setting instead of the edge? I live in an area where my phone can get both and it always goes for the edge signal instead of a weak H signal and the edge is soooo slowww.
hipertec said:
is there a setting that forces the G2 to go for the G3 or H setting instead of the edge? I live in an area where my phone can get both and it always goes for the edge signal instead of a weak H signal and the edge is soooo slowww.
Click to expand...
Click to collapse
*#*#4636#*#* then phone information, then scroll down and change the drop down from auto to wcdma only. Only problem with that is if u go to an area with no 3g, u get no service and have to change it back or go under the settings and wireless to enable 2g connections
Sent from my T-Mobile G2 using XDA App
Hey folks, I noticed that on my At&t samsung focus that the connection often doesn't switch down to edge when 3G is at no bars(tested-no data). And I know that areas I visit often have edge coverage because i can turn off 3G manually and get good reception... but any insights/solutions as to why the focus doesn't automatically switch bands/connections? radio bug?
edit: I did do the hsupa/dpa release hack via diagnosis console.
This also bugged me. In my experience this is not limited to the Focus. I encountered the same issue with the Tilt 2. It took probably a complete loss of 3G signal for the phone to switch to Edge and then even though the Edge signal had 2 bars, as soon as it got just a trace of 3G signal it went right back. Fortunately with the Tilt 2 I am able to turn off 3G and the phone stays in Edge all day long in areas where 3G os crappy. I wasn't able to do that with the Focus.
frighte said:
Hey folks, I noticed that on my At&t samsung focus that the connection often doesn't switch down to edge when 3G is at no bars(tested-no data). And I know that areas I visit often have edge coverage because i can turn off 3G manually and get good reception... but any insights/solutions as to why the focus doesn't automatically switch bands/connections? radio bug?
edit: I did do the hsupa/dpa release hack via diagnosis console.
Click to expand...
Click to collapse
I'm having these problems as well and I also did the hack. Since then I keep getting cannot connect messages in IE. It was so frustrating that I undid the hack(?) and this happens all the time. Can someone give me the settings to make sure I restored the original settings.
hello everybody...just received my quantum 2 days ago (i live in italy)...it was locked to at&t so i unlocked it with a code...but the reception is very bad, so i wonder...if i debrand the phone from at&t perhaps it will get better reception...what u think? because the signal only shows g/3g and no 3g+ or H....i'm a bit worried about that...help please! =)
Beggy90 said:
hello everybody...just received my quantum 2 days ago (i live in italy)...it was locked to at&t so i unlocked it with a code...but the reception is very bad, so i wonder...if i debrand the phone from at&t perhaps it will get better reception...what u think? because the signal only shows g/3g and no 3g+ or H....i'm a bit worried about that...help please! =)
Click to expand...
Click to collapse
If the phone is showing 3G at any time, then you are set up for the appropriate bands to get high(er) speed data transfer and 3G voice. If you only see E, then your carrier is using the other bands and unfortunately, there is no way to reconfigure the phone via firmware.
As far as general reception capabilities of the Quantum, I find it to be superior to the S-E X10 I used to use (I still have it), so I don't think there is anything wrong with the design. What phone were you using before?
drtolson said:
If the phone is showing 3G at any time, then you are set up for the appropriate bands to get high(er) speed data transfer and 3G voice. If you only see E, then your carrier is using the other bands and unfortunately, there is no way to reconfigure the phone via firmware.
As far as general reception capabilities of the Quantum, I find it to be superior to the S-E X10 I used to use (I still have it), so I don't think there is anything wrong with the design. What phone were you using before?
Click to expand...
Click to collapse
i had an omnia 7...but it's the first time i use a phone that comes from the US...dunno, it's weird, because when the omnia was under hspa, tha phone showed me always 3g+...and with tha quantum it shows me always 3g, and very poor reception (only 1 bar)....but the most of time the signal is under gprs only....it's pissing me off =(
You are correct. This phone has really bad wifi and wireless reception. I had flip phone before this and in places where I had 1 or 2 bars before with LG I have nothing, no signal. Yesterday I had to leave Ikea building and turn phone off/on just to get reception because if after spending 2 minutes outside he couldn't lock the signal.
Regarding wifi, at home I have hi-gain antenna on my router. I can take my laptop outside on the parking lot, sit in my car and still browser on the internet. This is around 30m distance through 1 thick concrete wall. This phone is struggling to get signal on the opposite side of the home, behind 2-3 drywall walls.
I constantly have signal changing between 3G and H. Were unhappy with reception.
AT&T phones don't show H+ (3G+), it just reports it as 3G. Signal wise I live out in the middle of nowhere and I got pretty decent signal with it. You can change your primary band settings under the MFG app though (because its AT&T if 2100 is available it automatically swaps to it, although where youre at 2100 may not be a primary band).