Database Users

Corrupted SD card possibly causes ADB in recovery?

somehow I think I corrupted my 2gb PNY class 2 card. I used ubuntu to format the card to ext4 file system, then used the vol- power button to get to recovery and bam! every time. THIS CARD DID NOT WORK BEFORE I DID THIS. now for some reason when I plug in this card to the ubuntu machine, it does NOT show up as a drive I can use, while the stock 2gb sandisk does. I tried multiple methods with this card, but this was my silver bullet. the stock sandisk card when used in a similar if not identical method did NOT work.
Anyways, finally rooted after hours of trying!

Gorden Freeman, it is you....
I love that game!
back to topic...
I have a pqi that is corrupt as well, it does not get me adb in recovery all the time. But it does do it every now any then. I think it is about 60/40 in getting me in.

Dr_Freeman said:
somehow I think I corrupted my 2gb PNY class 2 card. I used ubuntu to format the card to ext4 file system, then used the vol- power button to get to recovery and bam! every time. THIS CARD DID NOT WORK BEFORE I DID THIS. now for some reason when I plug in this card to the ubuntu machine, it does NOT show up as a drive I can use, while the stock 2gb sandisk does. I tried multiple methods with this card, but this was my silver bullet. the stock sandisk card when used in a similar if not identical method did NOT work.
Anyways, finally rooted after hours of trying!
Click to expand...
Click to collapse
Good one, I was about to try that until formatting my Transcend 4gb/class6 @ 1024k block size, FAT32 with the PB31IMG.zip as the ONLY file on the card stopped Bootloader, allowed me to downgrade HBOOT .77 > .79, then stopped recovery dead in its tracks.
To reiterate, for anyone struggling as I did with all kinds of loops, OSes (Windows 7 x64 and Ubuntu 10.04 and Linux Mint x64), scripts pull card push cable stand on my etc etc, Centon 8gb class6, 2X SanDisk 2gb, NOTHING worked until I did this:
**formatted sdhc card w/ FAT32 1024 block allocation size -- LONG method, named TEST
**copied fresh PB31IMG.zip from MejDam's ORIGINAL ez package to root (/) of formatted card
**power on to Bootloader, let sdcard check run while holding down Volume Power
**ok'd PB31IMG.zip update
**Rebooted holding Optical track button
**Power button to Recovery
**DECLINED PB31.zip
**(USB cable is connected this whole time)
**started .\loop.bat (available all over the place here) in Win7 x64 Powershell -- Administrator
**Power-button into Recovery
**Watch your error messages change, then proceed with the rest of rooting procedure, which is a lead pipe cinch if you follow most recent MejDam video with his commands/script
Again, my running theory (and others' theory), confirmed by the OP, is that the SDcard trips up recovery, allowing adb access. An abnormal/old card seems best. The Kingston 4gb/class4 that everyone else swore by did not work for me, but then again, my DI is <1 week old, had HBOOT .79, with a build of 5/14/2010.
Long story short: get a recommended spec card (1gb sd, 4gb sdhc, or 16gb class2 Moto or class6), format it normally, and if that doesn't work, try alternate formatting methods. I can say with almost 100% certainty that FAT16 does not work.
Anyone who needs help is welcome to reply or PM me. It was only through everyone here and MejDam that I was able to root, so thanks everybody!

ZIP File
copied fresh PB31IMG.zip from MejDam's ORIGINAL ez package to root (/) of formatted card
Click to expand...
Click to collapse
Where can I find this? I've tried everything else.
I'm going to do what you did. I have a 4 GIG card I'm going to format and throw the ZIP on and try that way. So I should format as a 1 GB card even though it's 4 GIG, right?

dreamersipaq said:
Where can I find this? I've tried everything else.
I'm going to do what you did. I have a 4 GIG card I'm going to format and throw the ZIP on and try that way. So I should format as a 1 GB card even though it's 4 GIG, right?
Click to expand...
Click to collapse
Here it tells you how.
http://forum.xda-developers.com/showthread.php?t=695825

THANKS!!!
Quick question though.... anybody have that ez root package? I'd like to see the contents of it.

dreamersipaq said:
Quick question though.... anybody have that ez root package? I'd like to see the contents of it.
Click to expand...
Click to collapse
Are you still looking for the PB31IMG.zip? Get it out of RUU...downgrade thread. If you're still having problems, PM me or gtalk rynosaur74

[Q] sd card ext partition...............?

Hello, i was searching these forums and couldn't find my answer. I just got a new 32gb sd card and would like to do a ext3 partition and instsall S2E. I copied orginal sd card to pc, then tried to do a 512mb, 0 swap on new sd. But for some reason rom manager gives me this triangle exclamation error picture. i really want to set up my 32gb correctly like you pro's! please explain how to set this situation up. greatly appreciated.

Is gparted the easiest way? Also should I use dt a2sd, or s2e?
"the only good bug is a dead bug"

gparted is what i recommend. Ive gotten Rom manager to work as well but a lot of people seem to run into the same problem you do when using it to partition.
And I prefer s2e for its simplicity and the fact that it persists through flashing nightlies (unless you do a full wipe). Its never given me any issues what so ever. DTa2sd works great and the only problems ive ever had with it are the getting it to initially flash. But once it installs its always worked for me. But if you're on cm7 theres no reason not to run s2e

Thank so much for replying and helping me out. Going to Google about gparted this weekend and figure it out. Again thanks for your two cents.
"the only good bug is a dead bug"

Gparted is fairly easy to do. Boot your computer into Ubuntu and connect your SD card to your USB port using a USB card reader (not your through your phone). Then just go to gparted in the application list and reformat and partition the card the way you wish.
Sent from my Liberty using XDA App

Just remember that the first (main) partition needs to be FAT32, followed by your smaller ext partition.

Gparted is not as easy as mentioned above. If you use windows system and not familiar with linux, it's quite complicated for my pont of view.
I guess you have two choices:
1. Gparted under win (Gparted+VMwareplayer), faster reading speed
2. Partition Magic(but reading speed for sd card might be slower than solution 1), easier operation.

So I ran the CD and my 32gb shows 26gb at fat32 and 4gb unallocated? Is my 4gb lost? ok... Got that problem resolved, now a new one. ive made my main fat32 and then for some reason i get a flag on my /dev/sdc2 ext3 partition after ive selected apply.

So I was wondering is the flag icon going to be a problem? Or is this puppy ready go!!!

Found the problem.....faulty SD card!!!! This a lesson to myself. Never buy a no name SD card from ebay. I grabbed a patriot, made myself an ext3 partition using gparted. No flag popped up and installed s2e and we are good now. Thank peeps. Delete this thread if you want.

I know you solved this but just throwing this out as an FYI...
I have the same triangle/exclamatiuon problem almost whenever I do a backup/restore etc...
I found if I pull the battery, and immediately reboot into recovery manually -- by pressing vol down and power, the phone takes the previous command (like backup/restore/partition) and goes ahead with it...
Maybe Mines' a failing SD card...but I back it up regularly

[Q] Problems with dual boot Phiremod/HC update, expanding sd card etc.

Can anyone help me out with updating the dual boot Phiremod/HC install?
My pc is a Windows 7 64-bit and I'm having absolutely no luck expanding the sd card to use the full 8GB.
Windows 7 and Easeus don't see the partitions, and Gparted does, but won't let me expand to include the free space (listed as unallocated).
I finally managed to mount the sd card via ADB, and have copied the phiremod update zip there, but when I try to install it, I get an error (bad) and after a restart, the file has vanished from the partition.
I'm very new at this, but can usually follow detailed instructions.

Here's what I did to update to 6.3:
Insert SD Card into my computer's card reader
Download EASUS Partition Manager (also using W7 64-bit)
Take the SD Card partition (#6 I believe) and extend it using the unallocated space left (mine was about 6Gb left on my 8Gb card)
Run the job in the partition manager
Throw SD Card and boot into Phiremod 6.2
connect to computer via USB and copy the 6.3 update to the SD Card
reboot in recovery, clear cache and dalvik cache (under advanced)
flash the 6.3 update zip
Mine hung at the android... screen for about 10min then I did a hard reboot and it fired up and has been working fine.
I was getting gmail force closes until I wiped cache and dalvik cache so I added that step in before flashing.
Let me know how it goes!

Ummm.... yeah, what he said above.
Thanks "toosurreal01"
It's great when a community like this helps each other out.
-Racks

toosurreal01 said:
Here's what I did to update to 6.3:
Insert SD Card into my computer's card reader
Download EASUS Partition Manager (also using W7 64-bit)
Take the SD Card partition (#6 I believe) and extend it using the unallocated space left (mine was about 6Gb left on my 8Gb card)
Let me know how it goes!
Click to expand...
Click to collapse
Thanks for the step by step instructions, but for me the buck stops at trying to extend the partition. Easus only sees the boot partition. Gparted shows all the partitions, but won't extend the sd partition. It looks like it should work (lets me drag the extender thingy), but when I apply the action, it reverts back to the original, with no error message. Just doesn't do it.
Should I start over and reformat the card?

It wouldn't hurt. Only thing you would lose are apps you've installed.
You could always use Titanium Backup for that though.
If you do reformat make sure you do a full format and not a "quick" one so no data is still lingering on the card.
Let us know how it goes!

siskiou said:
Thanks for the step by step instructions, but for me the buck stops at trying to extend the partition. Easus only sees the boot partition. Gparted shows all the partitions, but won't extend the sd partition. It looks like it should work (lets me drag the extender thingy), but when I apply the action, it reverts back to the original, with no error message. Just doesn't do it.
Should I start over and reformat the card?
Click to expand...
Click to collapse
Just a shot in the dark. But did you unmount the partitions first before applyin your changes in EAsus?

racks11479 said:
Just a shot in the dark. But did you unmount the partitions first before applyin your changes in EAsus?
Click to expand...
Click to collapse
Hm, no, I don't think so.
How would I do that? Card in Nook, or in PC?
Again, Easus only shows the boot partition, and nothing else.

siskiou said:
Hm, no, I don't think so.
How would I do that? Card in Nook, or in PC?
Again, Easus only shows the boot partition, and nothing else.
Click to expand...
Click to collapse
I meant gparted. Sorry. Did u unmount the partition before attempting to extend it?
And when doing so. Please don't do it while card is in nook. Only when its in PC directly with a nmicrosd card reader
Sent from my NookColor using Tapatalk

racks11479 said:
I meant gparted. Sorry. Did u unmount the partition before attempting to extend it?
And when doing so. Please don't do it while card is in nook. Only when its in PC directly with a nmicrosd card reader
Click to expand...
Click to collapse
Ah, do I need a usb micro sd card reader?
I only have a regular size sd card adapter for it.
And no, I didn't unmount the partition. I checked earlier, but there is no such option in the gparted menu, and I don't have much advanced partitioning knowledge.
A google search didn't help much.
Would appreciate if you could tell me how to do this!

siskiou said:
Ah, do I need a usb micro sd card reader?
I only have a regular size sd card adapter for it.
And no, I didn't unmount the partition. I checked earlier, but there is no such option in the gparted menu, and I don't have much advanced partitioning knowledge.
A google search didn't help much.
Would appreciate if you could tell me how to do this!
Click to expand...
Click to collapse
It is preferred to use a micro sdcard reader. I assume you are using a Linux box or live CD with gparted. But there should definitely be a n option for you to unmount the partition. You will not be able to make any changes to mounted partitions.
Right click over the partition that you want to work with. It should give you a menu. And unmount should be one of the options.
Sent from my NookColor using Tapatalk

racks11479 said:
Right click over the partition that you want to work with. It should give you a menu. And unmount should be one of the options.
Click to expand...
Click to collapse
Thanks for all your help!
I'm using a live cd on a Win 7 pc, and there is definitely no unmount option in the right click menu when I boot into gparted. Not even a greyed out one.
I'll try and burn another cd and see if that changes things.

siskiou said:
Thanks for all your help!
I'm using a live cd on a Win 7 pc, and there is definitely no unmount option in the right click menu when I boot into gparted. Not even a greyed out one.
I'll try and burn another cd and see if that changes things.
Click to expand...
Click to collapse
That is very strange. There should always be an umoint option for partitions if gparyed recoginizes the drive. Hmmmm.... which version of Ubuntu are you using?
Sent from my NookColor using Tapatalk

I downloaded the Gparted live version 0.8.1-3.iso.

siskiou said:
I downloaded the Gparted live version 0.8.1-3.iso.
Click to expand...
Click to collapse
Yeah. Then there shouldn't be an issue. :/
It might just be an issue with your card reader.
Sent from my NookColor using Tapatalk

Thanks again. I'll report back in once I get a usb card reader!

racks11479 said:
It might just be an issue with your card reader.
Click to expand...
Click to collapse
Got a card reader and Easeus and Win 7 Disk Management can now see all the partitions.
No luck expanding the sd partition, though. The action seems to happen, but then everything reverts back to what it was originally.
No mount/unmount option anywhere to be found, not with Easeus, nor with Gparted or Win 7.
I'm out of ideas at this point and will reformat the card and start over.
Edited to add: Aaand I'm now having trouble doing *that*, too.
Tried it on the pc: no go.
Tried it on the Nook: it claimed the card was sucessfully formatted in about 1 sec, and then got stuck on that notice.
Waited 5 minutes, still stuck. Turned it off and back on, and Nook booted into Phiremod.
Any ideas how I can reformat this demon card?
Edited to add: Am now using a low level formatting tool and get "format error occurred at offset ...". The program is still running and seems to be formatting the rest of the card.
Does this sound like the sd card is damaged?

A couple other options for you to try:
SD Formatter 3.0 - Made specifically to format SD cards - http://www.sdcard.org/consumers/formatter_3/
Partition Wizard - This is the software I used to extend the SD Card partition. Really simple to use - http://download.cnet.com/Partition-Wizard-Home-Edition/3000-2094_4-10962200.html?tag=mncol;7
I would try formatting the SD card, reinstalling the dualboot image, the using Partition Wizard to extend the SD card partition.
As far as updating, I haven't tried the newest update the when I updated from 6.1 to 6.2 I plugged my Nook into my computer, dropped the update file onto the Nook's internal memory, then moved it to the SD card with the Root Explorer app.
Hope any of that helps. Good luck!

kwyrt said:
A couple other options for you to try:
Click to expand...
Click to collapse
Thanks! I will give those a try, since everything was still on the card after the low level format.
Who knew that reformatting would be such a problem!
Did you have to unmount the sd partition, before extending it?

I extended the partition with Partition Wizard immediately after burning the dual boot image. Never messed with mounting or unmounting anything. I'm a little new to this myself really. Why would you need to mount the SD card partition?

I didn't think I had to, but racks11479 mentioned it as a possible solution in this thread, so I thought I'd ask.
None of the programs had any success in reformatting my card, so I returned it to the store and got a replacement.
Now I'm very ambivalent about trying again and possibly messing up another card.
Can anyone here think of anything that I might have done (or should have done) to cause the card to act this way?
And if anyone feels like posting a baby step guide for someone like me, I'd very much appreciate it!
Edited to add: I just found the following
*********
It also will produce a multi partition removable disk for which windows will not allow you to re-partition. If you want to get back to "normal" disk you can reformat it with Hewlett-Packard Company's HPUSBFW.exe
***********
Also, I used an old 2GB card to reformat my NC (went fabulously easy) and then reformatted that and tried a CM7 rom, which worked, but was way too slow. This reformatted again, without any problems, so I'm not sure if the above statement (regarding bootable sd cards) is correct or not.
And if anyone feels like posting a baby step guide for someone like me, I'd very much appreciate it!

[Q] Help with partitioning SD Card

Hello first I want to say a big THANK YOU to everyone that has put time and effort into making the Nookie what it is today....but I have a noob question.
I recently got a 16gb micro SD and can successfully get the 0.6.8 Nookie to run on my nook color, my problems start when I try to "recover" my other 13gb's. Before I get burned and tossed aside I have checked
http://forum.xda-developers.com/showthread.php?t=922324&page=92
http://forum.xda-developers.com/showthread.php?t=883175&highlight=partition&page=103
and about 5 other pages and they all say the same thing..use EASEUS, grab the slide bar and voila. It appears to work but when I install it in the NC it either becomes very unstable or just boots to the NC as if the SD card was not there.
Anyone have any ideas?

Jeep_Lover said:
Hello first I want to say a big THANK YOU to everyone that has put time and effort into making the Nookie what it is today....but I have a noob question.
I recently got a 16gb micro SD and can successfully get the 0.6.8 Nookie to run on my nook color, my problems start when I try to "recover" my other 13gb's. Before I get burned and tossed aside I have checked
http://forum.xda-developers.com/showthread.php?t=922324&page=92
http://forum.xda-developers.com/showthread.php?t=883175&highlight=partition&page=103
and about 5 other pages and they all say the same thing..use EASEUS, grab the slide bar and voila. It appears to work but when I install it in the NC it either becomes very unstable or just boots to the NC as if the SD card was not there.
Anyone have any ideas?
Click to expand...
Click to collapse
I use Lexar Bootit ....a free utility...to format and flip the bit that says its a removeable drive, then your windows pc drive management can see and format it as full capacity fat32.

Hey thanks for the tip, unfortunately it won't work. I forgot to mention that I followed this tutorial ..... and updated my driver (saved my original Windows just in case) to a hitachi driver and now I can switch my SD memory card forth "removable" to "logical" and back when needed. Once I get it as a logical drive I was EASEUS to increase the size of partition 4 (SD Card)..but again no dice!!!
Seeing that I am a noob I can't post the link to the tutorial but I'll say it worked like a charm and when I want to go back to the original I just need to "roll back" the driver.

Well, a couple of things:
Are you using a Sandisk card? Sandisk class 2 and 4 cards have been found much more stable than most others for running a ROM from SD, and problems with SD installs often go back to the card.
Any particular reason you went with Nookie Froyo? It has pretty much fallen out of use since the NC's stock OS was updated to Froyo in May. If you want an SD install, there's a simpler, size-agnostic method for CM7, which is also a more robust and capable OS and a more advanced version of Android (Gingerbread 2.3.4 rather than Froyo 2.2). I would recommend CM7.1 RC1, or if you're adventurous, Nightly 136.

Taosaur said:
Well, a couple of things:
Are you using a Sandisk card? Sandisk class 2 and 4 cards have been found much more stable than most others for running a ROM from SD, and problems with SD installs often go back to the card.
Any particular reason you went with Nookie Froyo? It has pretty much fallen out of use since the NC's stock OS was updated to Froyo in May. If you want an SD install, there's a simpler, size-agnostic method for CM7, which is also a more robust and capable OS and a more advanced version of Android (Gingerbread 2.3.4 rather than Froyo 2.2). I would recommend CM7.1 RC1, or if you're adventurous, Nightly 136.
Click to expand...
Click to collapse
Thanks for the info unfortunately I am using a 16gb PNY, class 4 and at $15 I couldn't pass it up...looks like I should have done some more reading first. Really I have no clue why I am using the Nookie, my wife said said that was the one she wanted. I think she just likes saying "Nookie", but I'll give the CM7 a go and see what trouble I can get into.
thanks again...

Taosaur...I was able to get the CM7 mod up and running in no time flat. Now the wife wants me to see if I can get bluetooth working.

You said "I was able to get the CM7 mod up and running ...." so I assume you got your problem fixed. That's good.
About bluetooth.
1. Turn off Wifi
2. Power off NC
3. Power on NC
4. Turn on bluetooth
5. Turn on wifi

votinh said:
You said "I was able to get the CM7 mod up and running ...." so I assume you got your problem fixed. That's good.
About bluetooth.
1. Turn off Wifi
2. Power off NC
3. Power on NC
4. Turn on bluetooth
5. Turn on wifi
Click to expand...
Click to collapse
Yep, I had to do the above the first time I turned on bluetooth, but haven't had any trouble toggling it on and off since then. Just open notifications (that broken-circle-and-arrow button on the status bar) and you have toggles there for Wifi, bluetooth, and a couple other things.

@ Taosaur,
I've seen your signature indicate you are running nb136, any change or improvement (both slightly and/or significant) over the previous ones?

Jeep_Lover said:
Thanks for the info unfortunately I am using a 16gb PNY, class 4 and at $15 I couldn't pass it up...looks like I should have done some more reading first. Really I have no clue why I am using the Nookie, my wife said said that was the one she wanted. I think she just likes saying "Nookie", but I'll give the CM7 a go and see what trouble I can get into.
thanks again...
Click to expand...
Click to collapse
Damn! My wife never says "nookie".

votinh said:
@ Taosaur,
I've seen your signature indicate you are running nb136, any change or improvement (both slightly and/or significant) over the previous ones?
Click to expand...
Click to collapse
I haven't done much but read and browse a little since I flashed it, but I haven't noticed any difference from 7.1 RC1, which wasn't really any different from Nightly 102 I had before that. I mostly just flashed this time for the integrated OC/Tweaks kernel, without the video/lag problems that were reported in 132-134.

Thanks for an update, m8

maybe someone can help me, i'm about to loose my mind here trying to figure this out. i'm using a Sandisk class 4 16gb card running CM7 with the OC kernal.Did all of this using the size agnostic install method. everything is working fine but i can't for the life of me figure out how to access the rest of the space on my SD, when i insert the sd card into my PC it just shows up as the 115mb partition. i've tried using EASeus, the lexar bootit, and some other partition tool with no luck. with Easeus i select the 13gb FAT32 partition and make it active and thats it right? does it need to be logical? and which partition am i resizing?

Dr. Light said:
maybe someone can help me, i'm about to loose my mind here trying to figure this out. i'm using a Sandisk class 4 16gb card running CM7 with the OC kernal.Did all of this using the size agnostic install method. everything is working fine but i can't for the life of me figure out how to access the rest of the space on my SD, when i insert the sd card into my PC it just shows up as the 115mb partition. i've tried using EASeus, the lexar bootit, and some other partition tool with no luck. with Easeus i select the 13gb FAT32 partition and make it active and thats it right? does it need to be logical? and which partition am i resizing?
Click to expand...
Click to collapse
None of the above. Windows will only recognize the first partition on a SD card, and when you make a SD bootable, that first partition will be the boot partition. To access the larger storage partition, connect your NC with CM7 running to the PC over USB. Open notifications on the NC, tap through "USB connected" to the USB screen, and "Turn on USB storage." Windows will now detect two storage drives, NookColor (the system partition, where apps install) and SDcard (the large storage partition).
The only time you'll want to remove the card from the NC and plug it into your PC is when you want to put on a new cm...zip update file to flash a new ROM.

I used the size agnostic install method with a 16gb PNY calss 4 SD and after all the steps were completed I was showing 13.8gb free for my SD card when I looked at in on the NC. Not believing my eyes I pulled it out and looked at it with EASUS and it showed partition 4 as 13.8gb (utilizing all the cards remaining space). I then downloaded a few things and added a few books for my wife and the space shrank to 13.4gb. As stated above your computer wont show it.
In short have you looked on the NC under "Storage" (I think that is were I found it) and verified you don't have the full capacity already?
Also there is another method I needed to use when I was messing with an earlier version (Nookie) that allowed me to see an SD card as a "Local Device" so windows would let me see all partitions on the hard drive. I can't post a link until I have more posts but email me and I can send you the link if interested.

Taosaur said:
None of the above. Windows will only recognize the first partition on a SD card, and when you make a SD bootable, that first partition will be the boot partition. To access the larger storage partition, connect your NC with CM7 running to the PC over USB. Open notifications on the NC, tap through "USB connected" to the USB screen, and "Turn on USB storage." Windows will now detect two storage drives, NookColor (the system partition, where apps install) and SDcard (the large storage partition).
The only time you'll want to remove the card from the NC and plug it into your PC is when you want to put on a new cm...zip update file to flash a new ROM.
Click to expand...
Click to collapse
thanks, well that got me some where. i connected nook to PC, turn on storage mode and it shows E/F drive. click either one and it says "Please insert disk into removable disk E/F" so then i turn off debugging and the nook color internal memory pops up as drive F, while clicking on drive E gives me the same error as above. any ideas? btw i'm on Windows 7 64bit, do i need any kind of special drivers or anything?

It is because windows will only allow you to manipulate the first partition on an SD card...even if it "sees" the other partition as another card it will not do anything with it. EASEUS will show you all the partitions on the SD.
The only way I got Windows to see all the partitions and do anything with them was to change my driver via the "Hitachi fix" If you google Hitachi driver SD card you will find it. I used this site and even though it is long it did exactly as advertised and now I install this driver when I need to format just the partition of an SD card and then "roll back" the driver when I'm done. It tricks windows into thinking it is a local device instead of removable. www/1src/com\forums\showthread.php?t=133718
change / to .
\ = /
I can't post a link as I'm still a noob...

Jeep_Lover said:
It is because windows will only allow you to manipulate the first partition on an SD card...even if it "sees" the other partition as another card it will not do anything with it. EASEUS will show you all the partitions on the SD.
Click to expand...
Click to collapse
S/he really doesn't need Windows to do anything with those other partitions--I suspect messing with them was where s/he went wrong in the first place.
Dr. Light said:
thanks, well that got me some where. i connected nook to PC, turn on storage mode and it shows E/F drive. click either one and it says "Please insert disk into removable disk E/F" so then i turn off debugging and the nook color internal memory pops up as drive F, while clicking on drive E gives me the same error as above. any ideas? btw i'm on Windows 7 64bit, do i need any kind of special drivers or anything?
Click to expand...
Click to collapse
I suggest you start over, because you probably damaged your install when you were messing with the partitions earlier. I'm also using Win7x64, and no, I didn't need any special drivers. Delete all partitions except "SDcard" in EASEUS, expand that partition to the whole card, then write verygreen's image to the card again and re-install. At that point, you should be able to access storage over USB from CM7 without turning off debugging or taking any other special steps other than "Turn on USB storage."

Taosaur said:
S/he really doesn't need Windows to do anything with those other partitions--I suspect messing with them was where s/he went wrong in the first place.
I suggest you start over, because you probably damaged your install when you were messing with the partitions earlier. I'm also using Win7x64, and no, I didn't need any special drivers. Delete all partitions except "SDcard" in EASEUS, expand that partition to the whole card, then write verygreen's image to the card again and re-install. At that point, you should be able to access storage over USB from CM7 without turning off debugging or taking any other special steps other than "Turn on USB storage."
Click to expand...
Click to collapse
alright i'll give it a shot when i get home from work. is the verygreen image the same one found in the CM7 size agnostic SD thread?
"http://crimea.edu/~green/nook/generic-sdcard-v1.3.img.gz"
and when i delete all partitions except for "SDCARD" do i need to make that partition logical or active or anything?
again thanks for your help.

Dr. Light said:
alright i'll give it a shot when i get home from work. is the verygreen image the same one found in the CM7 size agnostic SD thread?
"http://crimea.edu/~green/nook/generic-sdcard-v1.3.img.gz"
Click to expand...
Click to collapse
Yep, verygreen is the author of that thread and image.
Dr. Light said:
and when i delete all partitions except for "SDCARD" do i need to make that partition logical or active or anything?
Click to expand...
Click to collapse
No, in fact you might be able to write the image without messing around in EASEUS at all--I'm just not sure if WinImage (or whatever) would write to the whole card or just one partition. I know if you tried to format it, Windows would only format the boot partition.

[Q] Chronic "Unexpected Lack of Boot Partition on the SD card! Please Report"

[Q] Chronic "Unexpected Lack of Boot Partition on the SD card! Please Report"
Hi,
First let me say - YES, i have searched all of the forums here (and a number of other sites) and seem to have tried almost every option.
I have Chronic "Unexpected Lack of Boot Partition on the SD card! Please Report" problems. The farthest I get guaranteed is the cyanogenmod boot and menu (if I try and bring it up). I'm simply trying to get the SD card with cm7 to boot reliably and not eventually loose the boot partition.
Off and on since spring I was able to burn a CM7 image (verygreen's size agnostic, and one or two others I have since lost track of) to a SD card; have had it boot to cm7 and it work for awhile - but then eventual degraded into the no partition found error. the majority of the time it just doesn't work and results in that annoying purple black screen.
When it does work, it only works for awhile and then the boot partition can't be found; a few very small 3 of times - if I copied a new update it woke back up ad worked for a couple of reboots then lost the partition again.
Anybody got time to take pity on my melted brain and take a few guesses?
Clearly I'm not only missing something - but as things have gotten worse, am now missing more (if that is possible) as I'm going backwards to see why it no longer works at all.
At this point wrong has happened so often, I'm just lost on what even worked way back when I started.
I'm trying to backtrack to where it at least worked a little for a few days...but noob world is decaying into worse world.
I tried a couple of other, older processes and a multiboot menu one that seemed promising (plus could handle the new naming conventions for 7.2 CM7); but that one never even got past the missing boot partition.
I have tried approx 10 2gb SDCards, Sandisk, Kingston, Unknown; Class 4 and mixed.
I have tried 3 8GB SD Cards, Sandisk, class 4
I have tried 1 16gb SD Card, Sandisk, class 4
I have tried a Vivitar Micro SD Card Reader
I have tried the micro SD card Adapters in a laptop, and then in a sandisk USB adapter.
I even tried doing it all using the Nook color via a USB cable.
I even tried leaving the nook color off and connecting the USB cable to the PC to initiate a boot.
Using Windskimager
Using SD formatter
Have formatted Full erase and overwrite.
Tried leaving partition size alone
Tried partition resizing up to 250mb
Tried cm7 zip alone and with gapps
WinXP on 2 desktops and a laptop

It sounds like you have run the gamut of attempted resolutions.
That message is part of the verygreen partitioning script that runs every time the verygreen recovery is run. So, that means the normal boot kernel for CM7 is not loading.
The way the verygreen SD should operate is it starts with uImage and uRamdisk on the boot partition. Those are verygreen's recovery files. The first time it is booted, it looks at your emmc to be sure it is a nook. Then it looks at the SD to see if it has been partitioned yet. If it is not, it partitions it into those partitions necessary for installing ROMs. After partitioning, it looks for a zip to install. If it does not find one, it shuts down and the next time it boots it does the same thing until it finds the first ROM zip to install. If it finds one, it installs it. The first time it installs a ROM, it renames those uImage and uRamdisk verygreen files to uRecImg and uRecRam and they become the verygreen recovery files. And it installs new uImage and uRamdisk files from the zip to become your CM kernel and ramdisk. These are what normally will load in the future to start CM.
Now, with the disk partitioned and CM installed, ordinarily, after the cyanomod logo comes up, it boots by default to CM via the uImage and uRamdisk files. If you intercede with the boot menu and tell it to boot to SD recovery, it looks for uRecImg and uRecRam to load the verygreen recovery. If that is loaded, the verygreen script does all its checking again, it verifies that emmc is a nook, then tries to verify if the SD is partitioned. If it is, it looks for a new zip to install. If, in checking to see if it is partitioned, it cannot find partition 1, it gives that message that has been bugging you.
So I see two things that are happening to you.
First, it is booting to the verygreen recovery first instead of CM. That could be due to a recovery bootloop happening. Look at my tips thread linked in my signature to see an explanation as to what that is and how to possibly get out of it.
Second, after it boots to the verygreen recovery, it does its checking and cannot find partition 1 of the SD and gives you that message.
What I cannot understand is, if you have no partition 1 on your SD, how is it booting to the verygreen recovery?
What you have not told us is what you have on emmc. Stock? Does it boot properly without the SD installed? Or does it go to stock recovery?
After this happens to you again, take the card out and put it in the PC. Tell us what you see. What files are there? Maybe look at it with Mini-Tool Partition Manager and see what partitions it reports.

leapinlar said:
What you have not told us is what you have on emmc. Stock? Does it boot properly without the SD installed? Or does it go to stock recovery?
Click to expand...
Click to collapse
Ditto on that - especially as it boots happily to that error message time after time after the green cyanomod screen appears and I can also do the menu trick to get it to go into recovery.
Just as a clarifier: A number of times it tried to do the install (text flowing by) and at the end claims it can't find the boot partition - odd (unless I have less of an idea of what I am doing than I think) as isn't all that running from that partition? A fairly even number of times it doesn't even run the install and just errors out right up front.
Once in a great while it all works, and I'm good for a few days - but eventually upon rebooting to get it back to normal (either by menu choice or by pulling the sd card) - all I get is that lack of partition again.
leapinlar said:
What you have not told us is what you have on emmc. Stock? Does it boot properly without the SD installed? Or does it go to stock recovery?
Click to expand...
Click to collapse
Yes with the SD card out it boots to stock, although a few time what looked like the CWMod menu came up after I shut down and started up without the SD card installed. Maybe only 2 or 3 times out of WAY to many boots to stock so the kids could read their books while I went to work.
I have even tried resetting the nook to factory on the off chance I did something dumb while mucking about to cause that.
leapinlar said:
After this happens to you again, take the card out and put it in the PC. Tell us what you see. What files are there? Maybe look at it with Mini-Tool Partition Manager and see what partitions it reports.
Click to expand...
Click to collapse
Will do so later tonight and will read the notes in your signature as well.
I saw something go by about the boot partition having to start at the 63 block or something - I can't believe ALL my SDcard adapters / writers are bad, but could the nook reader be screwy? Anyway to do a real test? I've been using the Easeus Partition Manager, but will try the Mini-Tool Partition Manager.
Thanks for the step by step explanation of exactly what happens in the process so I can again get a handle on what it's all doing. That all makes sense to what it looks like it tries to do. Deeply appreciate the time!.

You know, I am beginning to suspect something is wrong with your card reader built into the nook. Some sort of intermittent thing like a pin not making a good connection to the card. Put an ordinary SD in it and see if your stock can consistently read it.
Is your unit still under warranty? You might want to explore seeing if you can get it replaced.

Your downloaded verygreen image might be corrupted. Have you tried re-downloading it?
Sent from my NookColor using xda app-developers app

leapinlar said:
You know, I am beginning to suspect something is wrong with your card reader built into the nook. Some sort of intermittent thing like a pin not making a good connection to the card. Put an ordinary SD in it and see if your stock can consistently read it.
Is your unit still under warranty? You might want to explore seeing if you can get it replaced.
Click to expand...
Click to collapse
I had thought of that too - at stock it seems to have no problems reading consistently; I've done surface tests using partition manager - but haven't located any real other options of hard testing like once done for hard drives.
Plus the fact that sometimes, it will work for days before it craps out.

j8048188 said:
Your downloaded verygreen image might be corrupted. Have you tried re-downloading it?
Sent from my NookColor using xda app-developers app
Click to expand...
Click to collapse
A number of times - I went through and wiped all my downloads for the latest try.

Okay So As I mentioned I went back and wiped everything I had downloaded and restarted (again).
Current status is it's working BUT:
suspiciously too easy this time, worked first shot
- (having said that, I've had looking stupid and asking suddenly means it all starts working - so if it's that I'm good with this)
I've only rebooted into CM7, not back to stock at any time
Have not removed the SD card
I've not had time to load up the apps I like, just the kids games
- (sometimes I think it's the more wanted, the less reliable)
Obviously because I haven't removed the SD card, i haven't been able to retry things enough to recreate the other problems of boots right, yet can't find the partition when it really counts.
Changes (listing stupid things too, just because):
-Went back to my sandisk class 4 16gb HC card
-changed USB adapter back to sandisk one, using a sandisk micro to SD adapter that specifically says sdhc (although I think that is really just marketing
-Formatted the SD in the Nook x2, and did not use SDformatter
-Looked at the partition on the card with MiniTool not Easeus partition manager
-There is a step in verygreen's where you pop the card out and reconnect to the PC BEFORE adding the cm zip, made sure to do that - but could swear I had done it before.
Full painful boring steps that SO far has gotten it past the first stage of creation (again the full test is when I boot into stock a few times, or remove the SDcard for anything, or load my really wanted apps on the android side):
--Also note my lack of class 4 Sandisk cards, I only had one after all. BUT I have had this all work to this point with the 16gb only to have it go south.--
Painful details is so I can catch what is really worthwhile different as even WHEN I get it to work, I'm going back to try all the other cards because it worked so oddly and failed so oddly and differently - but that's just me.
> The 2GBs are:
6 Sandisk SD, don't see any class Rating
2 no brand SD, don't see any class Rating
1 Kingston SD, don't see any class Rating
> The 8gb are SDHC "Adata" Class 4 SDHC
> The 16gb is a Sandisk Class 4 SDHC
Using the 16GB Sandisk Class 4
--------------------------------
> Nook booted to stock
Inserted SD Card
Unmounted
Formatted sucessfully
unmounted and removed
> Put in Red SD / SDHC Adapter
Put in Sandisk MicroMate SDHC to USB Adapter
Put in Front USB spot
> Mounted as E Drive
E Drive shows standard Nook Folders:
.amdroid_secure
B&N Downloads
LOST.DIR
My files
> MiniTool Partition Wizard
Surface test = all good.
>Write the image on your SD card
Used Win 32 Disk Imager
After done with writing, eject and then re-insert the uSD card into your computer.
Two Partitions - 118 and 14.72gb
>Copied to card:
update-cm-7.1.0-encore-signed.zip
Installed correctly
configured wireless
Rebooted = OK
Rebooted = OK
>Turned off
Removed SD Card
Put in Red SD / SDHC Adapter
Put in Sandisk MicroMate SDHC to USB Adapter
Put in Front USB spot
copied gapps
>Boot into Recovery
Gapps installed
> boot
all good
did all set ups like before
added apps (7 games for kids)
rebooted twice
started using
added one app I really like (newshog)
Listening for drumming... nothing so far (Dr. Who reference)
I'm going to go the weekend before rebooting to stock as I can do some adding, and rebooting to android.
Maybe backup the droid side this time around.
THEN the death tests on Monday
-thanks for listening_
p.s. - Yes, I still suspect the card reader somewhat as REMOVING may be where it breaks down.
However, once or twice when I had the Unexpected lack of boot partition error - I was able to bring it back by doing a CM7 update via recovery, despite it refusing to find the boot partiton immediately previously - of course that means the SDcard was removed and reinserted. Most time reinsertion = no help.

You do not need to remove the SD to test booting to emmc. Just press and hold the n button during the boot until the boot menu comes up. Then select emmc/normal and boot. It will boot to stock. The only problem with doing that is now your SD boot partition is 'sdcard'. But should work for testing stock.

leapinlar said:
You do not need to remove the SD to test booting to emmc. Just press and hold the n button during the boot until the boot menu comes up. Then select emmc/normal and boot. It will boot to stock. The only problem with doing that is now your SD boot partition is 'sdcard'. But should work for testing stock.
Click to expand...
Click to collapse
Yes, I know - but it's two separate tests to see which one caused the problem.
Turns out that neither was needed - it was easier to create; my son simply turned it off (not a reboot cycle as I had been doing which worked).
When it was turned on, it no longer boots - it goes straight to BSOD (actually deep purple).
Booting into recovery gets me:
Penguin Logo
rcS!
Populating /dev using udev: done
Initializing random number generator.... done.
modprobe: chdir(2.6.32.9): No such file or directory
Starting Network...
Detected Standard B&N nook layout, emmc first
Error! Unexpected lack of boot partition on the SDCARD!
Please Report!
Poweroff when ready
Since I'm till held to the noob reposting limit of once every 5 minutes and the captha I can barely read - I'll post MiniTool result in about 5 minutes. I'll link a screen capture if i can here.

I tried to boot per menu to the EMMC stock; Clockworkmod Recovery v3.2.0.1 came up. I know I did emmc and what ever the second default is (which should be normal) - I'm pretty sure it was normal.
I offed it and did the same and confirmed it was the default; THIS time it came up Nook stock.
Is there some way I installed something to the stock NOOK and didn't remove it when I restored to factory? The other day I did the restore from that same clockworkmod screen NOT from the stock Nook environment.
I'm wondering if I somehow created my own monster way back when I first started this and was playing in the android environment.

I just edited what I wrote a few seconds ago. The reason it went to emmc recovery is because the recovery flag was not reset when that SD Recovery told you that error. Did you read my tips about recovery bootloops? When you exited 3.2.0.1, it cleared the flag and booted normally.
I still suspect hardware issues.

Just for Ha, Ha's I hooked the Nook via USB to the PC.
G Drive "Removable Disk G" (wants a disk to be inserted)
E Drive "MyNookColor" ( Lots of what I assume to be standard Nook folders.

See my edit above.

Attachement # 1 SD Card from Mycomputer:
Attachment # 2 MiniTool View of SD Card

Boot Partition
Properties using Minitool Partition Wizard (attached):
Used
Partition Info
File System Info
Surface Test of Boot Partition:
Perfect - so no picture.
This is SO aggravating - I almost would accept just knowing why rebooting wrecks something if I knew WHAT).

leapinlar said:
I just edited what I wrote a few seconds ago. The reason it went to emmc recovery is because the recovery flag was not reset when that SD Recovery told you that error. Did you read my tips about recovery bootloops? When you exited 3.2.0.1, it cleared the flag and booted normally.
I still suspect hardware issues.
Click to expand...
Click to collapse
Sorry, apparently not closely enough - got lots of time again.
....didn't expect that anyone would be watching, was busy posting pictures so I could go away and read and think...
Probably is hardware - wish I had some way to vigorously test that, I get that basic use in Nook Stock doesn't really prove everything is good.
Plus I bought refurbished and I have to go dig up the warranty, it was months ago, so not too hopeful and boxes long gone. Don't know how nice B&N is, free replacement charger and cord is one thing - whole another refurb unit is different if I can't show stock SD card reading is an issue, not sure how much they check, but I don't think they care about CM7 off a SDcard not working!

Everything looks perfect on that card. All the right files, partition sizes, etc. You have stock on emmc, CWM 3.2.0.1 on emmc recovery.
I still suspect hardware issues. Powering off makes card semi-unreadable. Can still boot to it but when checking for partition information on SD fails.
If you registered your nook, the serial number is all you need. Refurbished usually have a one year warranty. Mine did. Just tell them card reading is intermittent. Which it is. They are pretty generous. You still have stock on there.
Edit: Try just an ordinary SD and power off, reboot, and repeat many times and in between check card reading ability.

leapinlar said:
Everything looks perfect on that card. All the right files, partition sizes, etc. You have stock on emmc, CWM 3.2.0.1 on emmc recovery.
I still suspect hardware issues. Powering off makes card semi-unreadable. Can still boot to it but when checking for partition information on SD fails.
Click to expand...
Click to collapse
Yup, it's really the only thing that hasn't been able to be changed through all of this.
I've mostly gotten these results - I've managed to make it worse as I redid things and apparently got sloppy. But when going back to methodically following instructions I have what I had months ago. I had hoped buying other cards would make it at least act differently.
Thanks for all of the reviews and double checking, at least I now it's not something obvious (but wasn't obvious to me) that I missed along the way!
I'll have to call B&N and see how strict they are and if they take the "It just has trouble reading any SD card consecutively".
Now where was that review of the Nexxus 7.... and I wonder how all the tablet prices are going to drop especially for the Galaxy Tab. Buying is not as fun but I am completely beat with modding failures.

We are too fast with each other. Lol. See my edit above.