Help! my Touch HD stopped working!! Need your help! - Touch HD General

Hi everyone,
Since yesterday my touch hd stopped working! It seems like the touchschreen is not working anymore. Only the power en volume buttons are working.
Because of this I tried to do a hard reset which resulted in the same problem. Now I'm stucked on the align screen. If I press really really hard I can align 3 corners of the 4 on the screen, so I can't get further to the next step.
Im currently in a hot hot Australia which might be the reason for all this. If you have a good look at the screen while turning it horizontally, you can see that one part has weird colours/reflection.
So what do you think? Can I buy a new screen and solve the problem or is there more going on?
Can I have warranty? The device is not having the stock rom on it. Can I maybe control the device and install the stock rom on it using a program on a pc or so?
Aaaaaaany help would be so appreciated! Im using the device as tomtom GPS as well, which I really need to travel to Melbourne next week. So I kinda need your help/advise cause I'm a bit in a hurry....
Thank you very much anyways!
Pauwel

Hi
Do a search on "newton rings" which I believe is the weird color / reflection problem.
As an aside when I knew I was getting a replacement I saw a post that suggested putting the phone in freezer for 10 minutes or so !
I did then wrapped it in tissue to absorb the condensation and it worked !!
r
Andrew

Plenty of threads on Newton rings if you search the General Forum like this one.
If its not Newton ring I you want to get past alignment, one method is to skip or bypass the alignment process altogether. Some Chefs do this already, namely Dutty, to among other things speed up the set up process.
How to do it: there are a couple of ways you can find in the forum, however, one way is to create a blank text file called, welcome.not, instead of welcome.not.txt, and place it in the root of your storage card. Next, flash a new rom or hard reset and you're done. It's up to you whether you leave your SD in during flash. I do not. If you do not, after the rom flash, stick your SD in and hard reset. If all goes to plan, the "welcome" phase will be bypassed, any you will not be prompted to align the screen or set the date, location, time etc. If for some reason it does not, go into the root of your SD and manually with your stylus or via activesync on your desktop create a new blank file in there and name it welcome.not. That actually worked for me. If it works then leave it in the root of your SD and it will allow the bypass with each new flash or hard reset.
The screen coordinates should load automatically after the bypass. If for any reason you need them, here are the Blackstone alignment coordinates from HKLM/Hardware/Devicemap/Touch/ Calibrationdata:
511,542 183,881 183,198 834,197 883,880.

Had that problem and you need a new ditigiter. Only problem is you will most likely break the screen replacing the ditigizer. So, the only fix is a new LCD screen and digitizer. You can get them from ebay. I did it and it was pretty easy, just take your time and get the videos and manuals people have posted on here. Good luck.

Related

Screen align issue WM6!

Have a Vario II with WM6 installed, works great but the screen alignment keeps changing all the time. need constantly go to Settings - System - Screen to align it again. What could cause this? The screen is kept clean with no scratches etc...
Digitiser could be going, You may need to replace lcd. If I was you I'd download "Remote Screen Alignment" and install to pc to keep your alignment settings on your pc. It won't fix the alignment problems but if your touchscreen does go and you try to hard reset or install new rom you'll be able to use the Hermes as you can restore the alignment settings from the pc. It'll keep you up and running until you get a replacement lcd(worst case scenario, Its better to have it with the alignment settings then to have to find someone with the same phone to retrieve the settings from).
Cheers...
you mean its soon time to retire my old Vario... II. too bad my laptop hard drive crashed a while ago and im only running linux ubuntu now... wont be able to connect Vario to it!
any other way to do it... please?
i dont want to loose this phone, or upgrade it as have a great deal wit t-mobile still...
thanks
check forum, you may be able to connect to linux. Not sure if Remote screen alignment will work though.
On Aussie ebay, a replacement LCD cost $70Aud including postage. I'd still look at that and see if you think its worthwhile fixing. You could also try to buy a "broken" Hermes off ebay, I've bought 2 (about $120Aud each) and so far there was nothing wrong with either. Ended up cannobilizing my old Jasjam.
Just a thought....
Cheers....
software test screen align
hi, all, i don't know if this thread is correct to insert my request.. but i try.. in this video http://it.youtube.com/watch?v=qPadyM66fDs the user open a software for test screen align.. anyone know what software is it?
thanks in advance
sorry for my english but i am italian...

Questions and Answers Section for BA Forum. Post Your Questions Here.

@All,
As a celebration for my 1000th post, I decided to open a new thread based on Tweakman's idea, which seemed to work very well in the Development and Hacking Section. The idea is simple, a single thread for all Questions, Problems, and Concerns regarding Blue Angel. This includes, but it is not limited to:
[highlight]*Problems with Flashing.[/highlight]
Can't get your device in bootloader? Did it freeze during flashing and now it doesn't get past the 4 colored screen? Are you a complete noob and need some guidance as to how to flash? Etc.
[highlight]*Have questions about which Rom is best?[/highlight]
[highlight]*Want to install software but don't know if it is compatible with your BA[/highlight]
You get my point. All the questions that I have seen/answered over the past couple of months are just repetitions of posts, threads, and things that are readily available on the wiki or in other threads. However, people are either lazy, don't know what a Wiki is / where to find it, or just flat out don't know how to search (or read the forum rules for that matter). Having something general (in this case a sticky) that says "Hey, if you have a question, you can ask here" should draw enough attention and start minimizing the number of new threads and posts opened by users (both new and seasoned). This way, we will be able to keep the development threads a little cleaner and smaller... hence making the site's search function work a little better in the process.
@Seniors,
Kinda like the Q&A team, I will need your help in trying to keep the influx of questions to a certain level by answering them as we see them. None of us are logged in 24/7 (or at least some of us aren't ), but if you guys see a question, please try to answer it. I know that xplode, Chef_Tony, markanthonypr, red_hanks, sun_dream, imatrix, +Que_PPC, motisu, and others normally try to keep this under control, but if we centralize it and contain it, we will have a cleaner forum.
Reserved for future use.
Post Stickied Per Request...
Siemens SX66 BlueAngel Q&A, Help
You know very well you can count on us. Great idea mate. Also congrats on your 1,000's post. I've added a few "tags" to the thread. I hope some others do the same to. Tags help users to find what they are looking for when they use search.
hi
hi specialists
my friend has Blue Angel,he has strange problems.
in (sounds & notification),it didnot saved after changing any parameter,we tried by reflash the rom again,but nothing changed,also we reinstalled radio 1.15 but no change,also the ring tone of the msg is discontinue or irregular when played,and some times didnot wake up (of the device) when recieve a msg.
this is strange issued problems but in mine (BA) every thing is ok,this problems only in my friend (BA),I mate PDA2K.
any ideas?any suggestions?
thnx
notice:when we down grade to wm 6.1 every thing is ok
homam_france said:
hi specialists
my friend has Blue Angel,he has strange problems.
in (sounds & notification),it didnot saved after changing any parameter,we tried by reflash the rom again,but nothing changed,also we reinstalled radio 1.15 but no change,also the ring tone of the msg is discontinue or irregular when played,and some times didnot wake up (of the device) when recieve a msg.
this is strange issued problems but in mine (BA) every thing is ok,this problems only in my friend (BA),I mate PDA2K.
any ideas?any suggestions?
thnx
notice:when we down grade to wm 6.1 every thing is ok
Click to expand...
Click to collapse
Hey homam,
Thanks for kicking things off
First of all, which OS were you having problems with? This is important because it could have been a bug in a rom that could have been fixed in a later version.
@mark,
I know I can count on you, buddy I need help from the mods as well though. I cannot redirect posts to here and/or close threads
My BA, keeps turning on from standby, by a light shock! I maen, if you press the Power button, and then you knock gently on it's back, it turns back on!!
I've set to "Lock all buttons except the power button", However, I still have this issue.
Well, I must confess that once it dropped off of my hand, and it's the result of that...
Any ideas?
by "it turns back on" i assume you mean it wakes up from stand by, it doesn't really start like after a soft reset, right?
since the BA's only battery activated wake-up is in the cradle and we are not talking about soft reset, my first guess is, the battery is not to blame.
have you checked whether you can use your camera at all time? i mean, the camera_detect does not usually run at all times but if the camera connector is a little lose, from now and then it could "discover" the new camera hardware and wake up, that is unlikely for normal devices, but if yours had a crash before...
you could refer to this site for checking possible hardware reasons:
http://www.land-of-kain.de/ppc/mda3/disassembly/
the hardware things aside, there are also many possible software reasons for the device to wake up on:
- update of titanium weather
- automatic email checking
- cell broadcast
- if bluetooth is on
- if beam is on
- automatic update of any software...
plus of course the usual:
- incoming call
- incoming text message
- incoming mms
- upcoming calendar event...
so please check the possible software wake ups first to make sure this is really a hardware issue, because that would be a shame, that could be tricky to solve.
or let me put it this way, if it is really the moving that wakes it up, you have the first BA with accelerometer
EDIT: last but not least, it could only be a bug, maybe a hard reset or change of the rom could also be a way to go, since spontaneous waking up is a known bug for BAs
Chef_Tony
If there was only a way to hack the hardware and make this work at least on Edge. I can live with everything else, but its a shame paying for a full unlimited Internet service and only getting G connection Sighhhhhhh
Ok, I had to let that frustration out !!!!!!
Chef_Tony said:
by "it turns back on" i assume you mean it wakes up from stand by, it doesn't really start like after a soft reset, right?
since the BA's only battery activated wake-up is in the cradle and we are not talking about soft reset, my first guess is, the battery is not to blame.
have you checked whether you can use your camera at all time? i mean, the camera_detect does not usually run at all times but if the camera connector is a little lose, from now and then it could "discover" the new camera hardware and wake up, that is unlikely for normal devices, but if yours had a crash before...
you could refer to this site for checking possible hardware reasons:
http://www.land-of-kain.de/ppc/mda3/disassembly/
the hardware things aside, there are also many possible software reasons for the device to wake up on:
- update of titanium weather
- automatic email checking
- cell broadcast
- if bluetooth is on
- if beam is on
- automatic update of any software...
plus of course the usual:
- incoming call
- incoming text message
- incoming mms
- upcoming calendar event...
so please check the possible software wake ups first to make sure this is really a hardware issue, because that would be a shame, that could be tricky to solve.
or let me put it this way, if it is really the moving that wakes it up, you have the first BA with accelerometer
EDIT: last but not least, it could only be a bug, maybe a hard reset or change of the rom could also be a way to go, since spontaneous waking up is a known bug for BAs
Chef_Tony
Click to expand...
Click to collapse
Wow! Tony! I really appreciate your complete answer. I mean it.
Yes, as you correctly assumed, I meant wake-up. It just wakes up and continues the routine WinMo operation; no soft-reset occurs.
It's less than a year that I've replaced the battery with a new one. I remember all the funny things used to happen when the old battery was dying. But non of them were similar to this one.
It can't be the Camera. Well, I'm able to use it all the time, and the "camera_detect" has been always loaded in the processes whenever I've checked it. About the looseness thing, ummm, I'm not sure. I tried to knock on it to see if it's more sensitive than other parts. I think the upper part of the device is more likely to wake it up by an easy hit (like knocking). but it's the whole upper part, not only the camera section nor the camera button.
Unfortunately, the software possibility, is unlikely to be the problem:
I've used many ROMs on my lovely BA which 3-4 times of them taken place since the wake-up problem.
The software and the usual reasons you counted, do wake it up. but shakes, too.
Finally, to be honest, I'm agree with you! This is the first Blue Angel with accelerometer. yeaaah! I did it!
I bet my friends that I can wake my BA up, without touching any buttons or screen! It's fun this way, but I comes to be annoying when I put it in my pocket or just put it on a table! and it wakes up... consider the forced battery consumption, unwanted screen taps if I don't lock the screen. God bless A_C! and... .
I know it's a hardware issue (((((
@raizaM: My Thought.... Have you ever taken it apart? One of my BA's had 3 loose bolts inside. All 3 were from what I think is the Radio/Antenna part at top. However, in my case, I had a rattle going inside. Thats why I put it apart. You might have something loose inside, causing a connection to arc when you knock on your phone. If you do deside to open it, there is a tutorial on the wiki on how to.
markanthonypr said:
@raizaM: My Thought.... Have you ever taken it apart? One of my BA's had 3 loose bolts inside. All 3 were from what I think is the Radio/Antenna part at top. However, in my case, I had a rattle going inside. Thats why I put it apart. You might have something loose inside, causing a connection to arc when you knock on your phone. If you do deside to open it, there is a tutorial on the wiki on how to.
Click to expand...
Click to collapse
Hey mark!
I had that same issue a while back, but with only one screw (also from the same area as yours).
@raizaM
Just to knock off Chef_Tony's theory out of the table completely, try to erase camera_detect.lnk from \Windows\startup and SR your device. If Chef was right, then your issue might be gone. However, I would follow markanthony's advice and take it apart in case Chef's idea doesn't work.
Oh man, your not my hero anymore LoL.. and here I thought I would be the only one with a mechanic inside my phone.
markanthonypr said:
Oh man, your not my hero anymore LoL.. and here I thought I would be the only one with a mechanic inside my phone.
Click to expand...
Click to collapse
Well, it kept me entertained when my BA would run out of juice
Thanks for your kind advices.
Actually, I tried to remove "camrea_detect" from the startup once, but any way, I gave it a shot again... no success...
Frankly, I'm a lil bit afraid to take my lovely BA apart... :-s... What if... :-(
But, I guess sooner or later I need to do so. so what the heck... lets do it.
Maybe I'll do it tonight. Guys please help me through it. I don't wanna loose my Angel!
Ton'y link provided in the previous posts, would be my start:
http://www.land-of-kain.de/ppc/mda3/disassembly/
any more advices?
raizaM: You're not going to go that far deep. Only remove the cover. If you look at picture #4 on that link, the top green area has about 6 bolts all around it. Those were the ones that were loose on mine. 2 of them were rattling inside the phone. I still can't believe they didn't cause a short circuit. You don't need to go down into the camshell area. Do you use the sliding keyboard? If so, you could have a bad flex cable. But, don't worry about tha for now. Just remove back cover and carefull inspect for loose bolts. Don't over tighten them.
all the master please help, my BA strange,,,,, the screen suddenly go dead after actived wifi or playing game, its suddenly dead, and i must push power button to turn it on again through proses like softreset, that in battery power. but if i conect in charger power mode, i turn wifi,playing game, its normal, the BA still on and working normal,
please2,,,,,if someone knows the problem please help, im desper now....
loryshoe said:
all the master please help, my BA strange,,,,, the screen suddenly go dead after actived wifi or playing game, its suddenly dead, and i must push power button to turn it on again through proses like softreset, that in battery power. but if i conect in charger power mode, i turn wifi,playing game, its normal, the BA still on and working normal,
please2,,,,,if someone knows the problem please help, im desper now....
Click to expand...
Click to collapse
It seems that you have the backlight settings set to dim/turn off too fast. Go to \Settings\System\Backlight and modify the settings in there (particularly the ones labeled "On Battery Power"). Then, soft reset the device (stylus on the bottom).
Hope this helps.
markanthonypr said:
raizaM: You're not going to go that far deep. Only remove the cover. If you look at picture #4 on that link, the top green area has about 6 bolts all around it. Those were the ones that were loose on mine. 2 of them were rattling inside the phone. I still can't believe they didn't cause a short circuit. You don't need to go down into the camshell area. Do you use the sliding keyboard? If so, you could have a bad flex cable. But, don't worry about tha for now. Just remove back cover and carefull inspect for loose bolts. Don't over tighten them.
Click to expand...
Click to collapse
egzthunder1 said:
It seems that you have the backlight settings set to dim/turn off too fast. Go to \Settings\System\Backlight and modify the settings in there (particularly the ones labeled "On Battery Power"). Then, soft reset the device (stylus on the bottom).
Hope this helps.
Click to expand...
Click to collapse
not the setting, it got black scren, its dead screen after running wifi or application, suddenly goes dead, black screen,.
Have you tried with another battery? It sounds to me like your battery is about to die. It won't hold the heavy battery consumption of Wi-Fi and heavy CPU usage while on Games. Try with another battery. Also make sure you followed Egzthunders suggestion to change your Power Settings. If you still need help, post back and include more info about your device, such as, what version of Windows are you running and how old/new is your battery.

Get past tap Welcome with bad touchscreen?

Bought a donor phone that had known problems with the touchscreen. The owner did a hard reset thinking it would improve but the phone is stuck on the tap to begin Welcome Screen. I bought the phone because my radio is dead/dying on my Herm200 which is pristine physically.
First I can get into the phone via Activesync and it can read the SD card so I can explore the phone.
Tried the welcome.not on the sd card that people use on the Kaiser but it didn't work. Opened wordpad created a blank file and named it welcome.not.
Is there a file that I can delete or change on the phone that can get past the tap to begin screen. Going to swap the motherboard out but I want to test it before taking it apart. Test bluetooth, sim card and wifi as well as to check if its unlocked and what is the software version.
Thanks in advance.
If you have a 2nd Hermes, download an app called "Remote Screen Alignment" (freeware). It copies the alignment settings to the pc and allows you to set up the Hermes, after a Hard reset, using the backed up data. Its supposed to be for visually impaired users but I find it bloody awesome when the touchscreen doesn't work. You still have most of the functionality of the Hermes through the hardware buttons but there are things that require the touchscreen.
Good as a stopgap measure to use or test out the device.
Cheers...
Thanks - ended up by swapping the motherboard to the phone that had a bad radio but a good touchscreen. Everything worked out and at least I have one functioning phone. At least out of the deal I'll have a spare flexcable, dpad board, spare battery and stylus. My dpad on the now working phone I think is on its way out as I'm starting to get some screen washouts that can be recovered and when you use the directional keypad it sometimes doesn't work and can only be recovered by moving the scroll wheel. That swapout I'll leave for the weekend.

Urgent help required (touch screen problem)

i have a mda vario 2 ( hermes) i've been installed a rom called hermes_wwe_3.62 Malina2d now phone boots up fine but the touch screen dose not work at all ! can anyone help ? .
To get pass the alignment screen i had to create a file on storage card " welcome.not" and that got me pass alignment screen.
now i am a newbie so please all the help would be appreciated i did have a look for file called touch.dll to replace it but could find one. ( as i read somewhere that might be the problem.
my ipl -1.04 & spl-2.10.01ipro
i really don't know what to do i have tried to re flash the rom no luck there.
all the hardware buttons work fine.
Not sure about that one. Why not post the question in the thread from where you got the rom? That name doesn't ring a bell.
If not try flashing the stock shipped rom, or the at&t stripped to see if the issue goes away. If it does go away, then don't use that rom.
cant really remember where i got the rom from as i the phone is my little sisters. do you have a link for the rom you suggested
My sig has the stripped rom, and the shipped at&t roms. You can also find some programs and my roms there too.
And to be safe make sure that hardspl is installed.
If that doesn't fix it, there might be a hardware issue.
cheers for your help. i am going to download one of your roms and pray that might resolve the issue . what the latest hardspl ? i thought 2.10 was the latest ? how do i tell what is the on i have installed on the phone ? Hardspl and spl are they the same thing ?
If you flash one of mine, flash the at&t rom first, that will straighten out any issues with the memory.
if you have 2.10olipro, your all set! spl (or hardspl) is the bootloader.
no luck still having issue with the touch screen wont wont work.
the touch screen used to work fine before. all this it just became very laggy so i decided to upgrade the rom , i went to thru a few roms.
any other idea ?
i must say i do love your rom everything is set out all nice and neatly shame the touch isn't working.
Thanks for the compliment on the rom!
Sounds like it has some kind of hardware issue. If your inclined to take it apart carefully (I haven't taken mine apart yet), you might be able to check all of the connections, and for dirt or anything that might be the issue.
I believe there are disassemble instructions on the wiki.
Maybe someone with more experience in taking the phone apart can chime in.
touchscreen issue
i m having the stupid touchscreen issue i have tried everything ( including disassembly and removing gasket but it still does not calibrate
starting to hate that phone
Sounds like Digitizer could be dead.... Need to replace the LCD and Digitizer if thats the case.
The trouble with this is there are a few different things that could be causing this and just replacing the LCD might not fix it.
Sounds like it could be though. If you are having trouble, DON'T do a hard reset until you have installed an app called "remote screen alignment", freeware off the net. It copies the alignment info to the PC so you can do a quick alignment using the PC instead of the buggered screen. Otherwise you'll be going in circles for ever without being able to get into the today screen.
Cheers...
actually i have hard reset the device
the trick is to put a file called welcome.not on memory card to skip first time alignment
i'll change screen and see if it fixes itself later
i ll use the phone as it is till then
new lcd
i changed the lcd it worked flawlessly for 3 weeks then bang! the bottom half of the lcd stop to work
i think that the ribbon on the lcd got damaged when i installed it on the hermes the fact that it needs to be turned 360 degrees during assembly cause the problem any thoughts from you guys????

Urgent Help PLEASE!!! Blackstone Digitizer DIE

Hello i decide to post here because i dont know right now do is a ROM related problem or no and on the same time here will see it more peoples and hope someon to know what is this.
Yesterday something strange heppand with my Blackstone, without to do anything i just decide to see the time and when i turn on the device was totaly Freeze not reacting on any touch, im using the ROM from my signature from Mounth without any problem. So i was thinking that maybe its from the ROM what i did is Soft Reset few times But this does not help.. the device fully load But the screen is not responsive also the hardware buttons do not vibrate?!!? when i press them they do not react ot anything.
After i saw that the SR not helping i do a Hard Reset and when the device whole load the ROM and preparing for 1st time use i was not able to Calibrate the screen.. the strange thing is that the display react on touch because when im taping in the corners the crozz move and when i do all the steps just start from the begining all the time and i cannot pass this step.
After i saw that this do not help me alot i decide to Flash so i put Manualy the device in Bootloader mode and via PC methoud i flash a Brand new ROM, when the ROM fully load and im going again to the Align Screen i have again the same problem the procedure start over and over and i cannot do anything.
1st i was thinking that something heppand with my Display but i didn`t do anything with the device i mean drop it or damage it somehow.. this heppand like the device is at the table at home and few minutes Befor i speak on that Phone. On the same time Im sure the display react on touch even wrong... because when im pressing the X on the calibration screen is move and befor to do Hard Reset when i was with the ROM from my signature.. and restart few times.. when the phone Load a POP UP of notification appear and the strange things was that i was able to scroll it up and down with fingers so for this reason i was thinking is a Problem ROM and need to HR or FLasdh diferent ROM. The notification Pop Up that appear when you click the Taskbar somewhere you know that you cannot slide it because its static.. so how this heppand i dont know.
PLEASE IF YOU HAVE ANY IDEA what i need to do let me know this heppand for 1st time and i never hear for soooo weird Blackstone.
THank you in advance
P.S Today im 22 November im going to Repair Service here because my device still have One Mounth Warranty left so maybe im lucky or no will see that leter.. i post this because to let you know that its not necassery to drop or damage your device the Display (Digitizer) to Stop working.. in my sutuation the device was static on the table i never drop it and use it 20 minutes befor the display to die i make a call so im using this device from 23 Mounths and i think that just the Display Die itself.. and to be more corect the display still work and show everything but the digitizer DIE so have that on mind
I do now Task29 and re flash again the same problem its like the display reacting on touch but not corect... i think its something serious and i will need new Digitazer or Display or Both?!
Also Reverting Back to stock SPL and ROM do not help..
I think im for Repair Service
Thank you
tsalta said:
I do now Task29 and re flash again the same problem its like the display reacting on touch but not correct... i think its something serious and i will need new Digitizer or Display or Both?!
Also Reverting Back to stock SPL and ROM do not help..
I think im for Repair Service
Thank you
Click to expand...
Click to collapse
i still don't understand how the f*** does this fin into ROM development
but anyway it also happened to me,first the digitizer went a bit crazy,then it went completely crazy and than i replaced it with a new one
i did it by myself...it can easily be done if you have any hand skills and can hold a screwdriver
but be really careful with placing the new digitizer over the screen because any irregularity may cause dust to later get in between the two
digitizer is less than 20usd i believe...
lcd+digitizer are 60+ if i remember correctly
if you decide yourself for lcd+digitizer first check if those are already sealed to each other,because if not,you will have the same situation as if you ordered the digitizer only...but with 40+ usd wasted in vain
also be extra extra extra careful while removing old digitizer from the lcd
cheers
If you are stack in the align screen, try first to create a summy file named "welcome.not" and put it in the root of your storage card. This will allow you to go through ROM setup without align. Then check to see if the screen is responding and if not then you most probably need to do what farukb said above.
MOD EDIT - Moved to General discussion as not related to rom development
stathis95194 said:
If you are stack in the align screen, try first to create a summy file named "welcome.not" and put it in the root of your storage card. This will allow you to go through ROM setup without align.
Click to expand...
Click to collapse
In my case, the SD card was corrupted and in the next 3-4 days the touch screen is not responding either... I should note that in my case, I followed the advice by Stathis and created a "welcome.not" dummy file in the root of the phone's memory, so it skipped the screen alignment procedure. Unfortunately the screen is responding so I will have to take it to the service center in order to have it checked, in case it is still under warranty (I have bought it 2nd hand).
Otherwise, I will have to order a new screen and try to install it myself. Wish me luck!
Same here, i have some kind of smudge, like oil spill, on the screen. i thought of buying just the digitizer but as i disassembled it, found the digitizer and the display are a set, so don't bother buying just one of the parts.
@tsalta - since you're from BG, check this http://gsm-world.biz/index.php?main_page=product_info&products_id=2630
I successfully repair digitizer on my blackstone! It is hard work but its wotrh it.
Now I have to repair some more HDs. But its strange that all of a sudden all of the HDs I know broke dow in a period of one month... mine broke down at the end of october.

Categories

Resources