New WIFI Problem - No Connection - 8125, K-JAM, P4300, MDA Vario General

I've been crawling through the internet for 2 days now, still found no solution. (even used the search-form of course).
My HTC Wizard does not connect to WLAN.
it is a MDA Vario - AKU3-Rom (official from T-Mobile), IPL + SPL 3.08, no-CID, no-SIMLOCK...
Description:
When i open the comm manager, it shows the icon for not-connected wlan. when i click it, there is the "windows is running"-animation, but nothing happens.
The same with 3rd party devices (like Homescreen++, WIFIFOFUM). I dunno what to do... PLEASE HELP!
Start->Settings->Connections->WLAN contains only grayed textfields (SSID, Modus, BSSID, Tx-Rate, Channel, Signal quality) and there is no MAC- or IP-address specified...
Start->Settings->Connections->Network Cards does not show any networks, but a variety of drivers (i think) like: NE2000-compatible Networkdriver, SDIO WLAN Wireless Adapter. Upon opening them and selecting the automatic ip-gain the IP-Field says "no connection" instead of an IP-address...
(Pictures are from Bottoms-ROM, nothing has changed however i tried different ROMS...).

push
I have the same problem. Please someone help!

Try the following:
First use File Explorer on the device (or equally, browse device via computer and ActiveSync) and check to see if you have a file WifiInit showing in Windows\StartUp\ folder. This is the .lnk to the WifiInit.exe file in root the \Windows\ folder.
i) If the shortcut is present in the StartUp folder delete the shortcut (only) and soft reset your device. After re-boot try turning on WiFi. If it still doesn't work, then navigate to the WifiInit.exe in the root of Windows folder and click it to run the exe. Then try the Wifi again.
ii) If the shorcut is not present in the \Windows\Startup folder, then navigate to the WifiInit file in \Windows\ root, click it to run and check if WiFi works after that. If it does then you need to create shortcut in the \Windows\StartUp\ folder
Anything beyond this I cannot help further with.
Good Luck

Thnaks for your interest Nandaly!
Okay, i tried it with the O2-ROM installed.
There was the link in StartUp having 26Bytes on the phone.
WiFi still doesn't work after soft-reset.
So i looked in the Windows folder and there are 2 files: a link to WiFiInit.exe (sic!) and the file itself.
WiFiInit.exe (6.95KB) doesn't respond to clicking on it.
Wifi is now grayed out in the CommMgr.
With a new link in StartUp it's not grayed out anymore, but it doesn't work...
What i've seen on bootup is that the Wiz seemingly is trying to start the wifi and fails. (it takes longer before it launches the TouchFlow interface)
So i fear that the WiFi-EPROM is corrupted or it has sth to do with the battery that i had to revive. Since i didn't smash my device into the corner, i bet it is not a loose antenna...

Related

ActiveSync via Bluetooth link [solution]

I find this solution for running ActiveSync connected thru BT via one click. I tried it on my MDA Compact and it works.
Hope it helps.
http://www.mtekk.com.au/Forums/tabid/56/postid/14926/view/topic/Default.aspx
On the Pocket PC...
1. ActiveSync / Tools / Options... / Options... (yes options twice)
2. "When cradled Enable PC sync using this connection" 'Bluetooth
3. Startup an ActiveSync connection as you normally would...
4. Now setup a shortcut to the program "windows\repllog.exe" into the Start menu. To do this
a. open up Explore in ActiveSync
b. Go into My Pocket PC
c. Go into Windows folder
d. Find repllog.exe and right click and select copy
e. Go into the Start Menu folder (within Windows folder)
f. Right click, paste shortcut - rename to something like ActiveSync Direct
Back on the Pocket PC
5. Gracefully disconnect ActiveSync.
6. Start / Settings / Buttons
7. Choose Button 4
8. Set the button assignment as ActiveSync Direct (or whatever you called it above) and click OK
9. Reset your Pocket PC and wait about 15 seconds for everything to get loaded (esp. Bluetooth which takes a little while).
10. Press the top left side button. Voila! Easy!
If you get the ActiveSync - "Port Not Available" message, it just means that Bluetooth hasn't loaded yet. Tap OK, check that Bluetooth is activated and if so, try again.
Thanks for the post. Ive been having trouble getting this to work however.
1. ActiveSync / Tools / Options... / Options... (yes options twice)
2. "When cradled Enable PC sync using this connection" 'Bluetooth
3. Startup an ActiveSync connection as you normally would...
4. Now setup a shortcut to the program "windows\repllog.exe" into the Start menu. To do this
a. open up Explore in ActiveSync
b. Go into My Pocket PC
c. Go into Windows folder
d. Find repllog.exe and right click and select copy
Click to expand...
Click to collapse
Im using WM5, and firstly i dont have the option..option menu and secondly when i try to paste repllog it tells me that the file is copy protected or something like that.
Any ideas???
Help appreciated.....
Try to use Resco File Explorer instead of M$ Explorer. When you 'right click' on Windows/repllog.exe, there is 'Send To...' -> 'Start Menu as Shortcut' option in menu.
activesync has only com1!!!!!
hello pda masters!.i try to activesync my ipaq-2490, with usb,can sync.when i try to change com to sync by bluetooth, activesync has only com1, to choose.i have soft reset, my ipaq, (Xmany times), uninstall reinstall activesync 4.01, 4.02 (Xmany times).i eraze registry anfd reinstall, nothing.have you any idea? in the past i could sync by bluetooth, because activesync had com1,com2,com......., now has only com1.please help
sorry if i post in wrong thread, but i am new, and forgive my poor english, (i am from greece)
The best
http://forum.xda-developers.com/viewtopic.php?t=49136
IMHO
help with activesync only com1
every time i install bluetooth usb stack, it uses new com79, com80, now and i cannot sync over bt like i did before.
How can i delete those comports?in device manager under advanced in com1, tells me that from com2-com80 are in used.?????
Any idea, thanks
remove your stack from PC, then delete all com ports except 1 & 2 , use buttons windows + break & install stack again!
in properties of each ports set different com for example com1 , ignore errors , delete free changed one! do so with each wrong port
THANKS A LOT! PROBLEM WITH COM79,COM80,COM81......FIXED
thanx rustoss, you are BIG! i dont unplug usb stack even.....i just ignore all notifications and change my only COM1, to com5, and thats it!.i can activesync by bt again.thanks again :lol: :lol:

Certificate-issues when attempting to install on QTEK 9100

I've recieved a QTEK9100 (HTC Wizard) from my employer. The ROM-version is 2.18.7.4 NOR.
This unit seems to be application locked in some way.
Among other things, I have tried to install two different sharewhare GPS-programs on this unit (PTGMAP and OZIExplorer). When installing or running the .exe files i get error messages like:
- "Cannot open the file PTGMAP. It either lacks a signed certificate or cannot find one of the components" (my translation).
- ".. can not be installed because it does not have a digitally signed certificate" (also my translation)
- or simply "cannot be installed"
I've searched this forum and quite a few others, but I have not been able to find a solution. I've found some .cab files, but these have been for other units that the QTEK 9100/HTC Wizard. I was even able to install this one, but it seems to have made no difference:
ftp://[email protected]/Universal/Extended_ROMs/Default_Signed_DisableSecurity.CAB
(I do realise this is for another unit)
I've also tried SignCode - It's says that the executable is certified, but I still get the same error message when I try to run the programe.
Finally, because my ROM has been configured (by an external supplier) with Pylon Anywhere for syncronization, I guess I can't install another ROM, as I will lose this software which I need.
Can anyone help me here? --- Please!?! ---
Try this reg tweak
Disable the security warning when installing non-certified application
To disable the security warning when installing a non-certfied application, set:
HKLM\Security\Policies\Policies\0000101a = 1 (DWORD decimal)
To restore the warnings:
HKLM\Security\Policies\Policies\0000101a = 0 (DWORD decimal)
Registry editor
but... I've tried to install the registry wizard:
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
But I get the same error-message "cannot install RegistryWizard_PPC_ARMV4.cab"..
Any ideas?
Copy this exe to your device via activesync and click on file through file explorer. It is a registry editor and go to those keys i described.
Still doesn't work
I've tried this in every possible way now:
- I've copied the file to my "mobile unit" in windows explorer with ActiveSync running.
- I've put the file in the file-sync and synced.
- I've copied the file to my storage-card using a card-reader.
... Everytime I try to run the file, I still get the message "Cannot open regedit_463. It is either not signed with a signed certificate and so on..."
I am considering a ROm-update, but if I install a new ROM, I'll lose all the syncronization software from my employer, right?
Any futher help is greatly appreciated! Thanks!
Re: Still doesn't work
kloksa said:
I've tried this in every possible way now:
- I've copied the file to my "mobile unit" in windows explorer with ActiveSync running.
- I've put the file in the file-sync and synced.
- I've copied the file to my storage-card using a card-reader.
... Everytime I try to run the file, I still get the message "Cannot open regedit_463. It is either not signed with a signed certificate and so on..."
I am considering a ROm-update, but if I install a new ROM, I'll lose all the syncronization software from my employer, right?
Any futher help is greatly appreciated! Thanks!
Click to expand...
Click to collapse
Try the above file in main memory - take your storage card out and soft reset. Then click on the file again - sometimes it is a corrupt storage card that causes that error. Otherwise its some software thats caused this security error and you will need to hard reset or update rom. Yes you would have to reinstall all your software.

Cannot Synchronize, cannot install or uninstall apps on Universal.

Hello.
I seem to have made a "cleanup" of the Universal file in main storage (by only removing some today items not needed, and I think I removed a file inside WMDRM folder or something.
Anyway, since that day for some reason, my Universal connects to Activesync through USB but it Doesn't synchronize. I get a message on Activesync stating that sync cannot be made.
Also, I cannot install cab files moved Directly to my device. e.g. I have a file on storage card, run is, and get an "unsuccessful" message directly.
From the beginning, I couldn't uninstall any applications (with the 1.90.94 Aku3 rom...) and I could only do it from Activesync Install/Uninstall. Although the files apear in windows/installs (or something) folder, they are not shown on the device's add/remove programs function.
I don't care about uninstalling, but Installing and using Activesync is top priority. Any clues on how to solve it without a Hard Reset?
Thanks...

Please Help...wifi Problem

I install in htc touch the followings programms
Skype
ewallet
Pocket CM Keybord
sdkCerts + Windows Live 10.6.0034.0800 fixed
Now i go to Comm manager and i press the button for WLAN. The WLAN is dead. When I go to the Setting --> Connections the icon WiFi is disapear.
Please help me....i have bought the mobile 3 days ago with sim unlock,
Please help me
Uninstall everything you can, if it doesn't help, do a hard reset. After installing each CAB, try to use WiFi.
Hi i have the same Problem.
I instlled diverent Rom. Always the same. I cannot activate the Wifi.
What else can i do? Would another Radio Rom help?
I have done many times hard reset but nothing.
archonw? You have install different ROM and still cannot activate WiFi? Have yοu try original ROM?
I THINK I FOUND THE SOLUTION. In folder My Device -->Windows there are some files
There is a file Wrlsmgr. When i open this file then i see something like the Comm Manager. In this programm there is bluetooth and phone button. When i press the button i can activate or deactivate the phone or the bluetooth. I see then that there is no button for WLAN. I go to the files about bluetooth and phone and i see the followings files.
BluethSetting.htm
Bluetooth Explorer
BluetoothSetting.dll
phone.dll
phone.dot
phone.pwi
PhoneSetting.dll
Then I go to the files about wireless and i see the following files.
Wireless LAN
wireless.bmp
WirelessLAN.htm
WirelessService.dll
WLANSettings.exe
WLANSettings.exe.0409.mui
Do you see something strange? I see 2 thing. There is no a file WLANSettings.dll like bluetooth and phone and what is this WLANSettings.exe.0409.mui strange file?
If some want help me please i would like to see if my files is the same as the files in his phone.
Thank you very much

How to "attach" USB Tool and activate "Internet Sharing" automatically at startup ?

How to "attach" USB Tool and activate "Internet Sharing" automatically at startup ?
I "liberated" my XP downgraded HTC Shift and succesfully tested 3G connectivity.
The problem is that every time I restart the device, I have to:
1) enter WM
2) Attach device via USB Tool
3) Enable Internet sharing
As WM is an operating system, I guess how to do this automatically. Can I write a "bat" file to do these steps or do you have any advice to achieve this ?
Any help MUCh appreciated.
Regards.
joker197cinque said:
I "liberated" my XP downgraded HTC Shift and succesfully tested 3G connectivity.
The problem is that every time I restart the device, I have to:
1) enter WM
2) Attach device via USB Tool
3) Enable Internet sharing
As WM is an operating system, I guess how to do this automatically. Can I write a "bat" file to do these steps or do you have any advice to achieve this ?
Any help MUCh appreciated.
Regards.
Click to expand...
Click to collapse
go to wm -win start menu --settings--connection--ub to pc--enable advance network connectivity.
this should fix the problem, cheers
Unfortunately, it does not solve the problem.
I noticed that the only thing I have to do is to activate Internet Sharing.
How to do this at startup, automatically ? Has WinMo some autoexec file or startup folder ?
Thanks.
Up, please. I'm so near to surf only starting up my shift
Up. Up. Up. Up.
Yes I'm sure you can do all of that with Mort Script,
Good luck!
And don't forget to post your final results so other users would enjoy of that!
unapproachable2kx,
can you support me ?
Maybe you can just drop the shortcut for the application on the startup folder or maybe DotFred's TaskManager can help(http://www.dotfred.net/TaskMgr.htm).
wovens said:
Maybe you can just drop the shortcut for the application on the startup folder or maybe DotFred's TaskManager can help(http://www.dotfred.net/TaskMgr.htm).
Click to expand...
Click to collapse
WinMo has a startup folder (\windows\startup\) that you can create a shortcut for "Internet Sharing" inside, the problem is that you need a parameter with the shortcut to run the "Activate" conmmand in "Internet Sharing"; 'cause a normal shortcut will just run the app, then you'll have to press Activate manually (we want to automate that too); same thing for "USBTool". Unfortunaltely, I don't know the set of parameters for the shortcuts.
Or try looking for some advanced shortcut creation tools for WinMo, like in this list
http://en.handybyte.com/search/shortcut-mode/

Categories

Resources