Digitizer Problem - P3600 General

I have a cracked digitizer and got a replacement. I've replaced this in the past no problem. However, out of the two new digitizers I've tried, none seem to be working. The screen comes on ok but cannot tap anywhere. I've hard reset the device and now I cannot use the phone as I'm asked to align the screen. Any ideas as to what has happened? I've opened it up a hundred times each time checking the connection. Now possibly I need to replace the whole lcd screen but am reluctant to do if it still will not fix my prob. any help is much appreciated.

I just know there are two versions of LCDs (with digitzer) for the P3600. You have to check the serial on the back and get the exact one. Maybe it`s the same for the digitizers and You got some from the other serial line ?

Related

For anyone thats ever replace the LCD - white screen issue....

Hello everyone...
Ive been doing as much research as I can, but can't find any solution.
I had to purchase a new LCD screen for my cingular 8125.
When i installed the screen, it only boots up with a white screen. Ive read that this has happened to a few others, but no one has posted a solution.
All cables are connected securely, and pushed in far enough. i've experiment with everything. Ive hard reset, ive even tried with another motherboard from a different 8125 phone. nothing but a white screen. I plug my old screen in (still works, just discolored), and it works fine.
Ive read somewhere that there are two generations of the screens. But the part numbers on the screens match up, so im not sure that this is the problem.
Any suggestions? Could the screen just be no good?
Any help is appreciated.
Thanks!
I had a problem with a white stripe when I replaced my screen. I returned it and got a new one...problem solved.
i'm assuming im going to have to return it as well, but i'm trying to avoid the inconvience if possible. ive read that a few people have had this problem, and later replied to their own post saying they fixed it...but never said how...
I had this last week - it was a case of not quite seating the screen ribbon connector properly.
Severl times I fired it p only to see a fully white screen, playing around with the seating of the connector fixed it.
nope...ive messed around with it numerous times. just pulled it back out and tried again...actually hooked up what i needed without putting the phone back together so i could mess around with the ribbon while the phone was powered on...still just white....i suppose it has to be a bad screen?
could be a bad screen.
did you replace the tape that was on the LCD ribbon?
I have replaced about 25 screens and that tape is very important..trust me.

Screen alignment loop

Hi,
I got my 8525 secondhand off ebay, and I'm having problems with it. I did a clear storage or a reset of sort, and I'm stuck in loop of screen alignings. Originally, before I did the reset, the touch screen does not respond when I tap on the top right, and the screen alignment loop was also there when I chose to align screen and I had to take out the battery to fix it. I notice small pieces of cardboard stuck in between the side of the lcd and casing so would that be the problem here? Any help is appreciated, thanks.
Sounds like the digitizer is stuffed... You may have to replace the LCD.
You can get them off EBay for $70AUD and there is a Service Manual so you can open and fix yourself. Here - http://michael-channon.spaces.live....ner=1&partqs=cat=Download+HTC+Service+Manuals
Its not too hard but you will need a small flat blde screwdriver, a small phillips head and a size 6 torque key.
All the best of luck,
Cheers...
Thanks Ultramag
I did a bit of research, and I came across this thread. http://forum.xda-developers.com/showthread.php?t=405432
It seems we both have a similar problem. Would the software method work for my case? I want to avoid dismantling the hardware if possible.
Thanks again.
Yes and no. You need another Hermes (same model) to get the alignment settings from and this is only to get the phone operational so you can use it. It WON'T fix the touchscreen, Its just a stopgap measure until you replace the faulty LCD.
I was lucky as I have a few friends who I sorta got into the hermes who I could get the settings off. You can navigate around your hermes without th touchscreen but its a REAL *****. Bought a couple of Jasjams off the net and was lucky enough that BOTH worked. Still put my mainboard into 1 and gave the other to a friend who was having similar issues...
Hope that helps...
Thanks mate, I really appreciate it.

Dropped my Wizard - White screen

Hi to everyone.
I dropped my wizard and lcd broke so I bought a new one and put it on. The problem is that although it takes phone calls and it syncs to pc, the screen is always white with nothing written..only a white screen. I do not know whether another problem occured besides the broken lcd. I tried to disassemble and reassemble it again but with no success. Any help please?
Hi, If my understanding is correct there are 2 versions of LCD for the Wizard. Are you sure that you have the right one? I'm sorry that I am unable to offer any further advice except to say that if the phone 'phones' and 'syncs' the basics must be working. Also the white screen means that the backlight is working - the problem is the LCD drive. Perhaps worth checking with your replacement supplier that they sent you the correct part?
Good luck!

Hd2 screen replacement, now digitizer not working?!?!

For a bit time ago i accidently broke my lcd display on my hd2, and because htc could not fix this cheap i decided to try myselvf.
first i ordered a lcd and a new digitizer and soldered them together and fixed everything just like in the video and the lcd started to work, but now my touch pad does'n work! I can't do anything
Then i took the screen out and ordered a new one from ebay which was assembled from the shop.
And same resault
what could be the problem? I have a danish hd2 and i have tried to update the firmware after i replaced the screen and digitizer and still no respond
what could be the problem?
hey, did u fix the digitizer yet. i had a similar problem. the volume buttons got stuck in and i decided to open it and fix it. right after closing it back the digitizer stopped functioning...............please let me know asap if u managed to fix urs and how u did it thanks
Same problem here
I've got the exact same problem. Replaced LCD and digitizer but it is still not working. Additionally the screen is a little yellowish. Anyone knows if this might be related and any idea who to possibly fix this?
Hi, I have exactly the same problems, even tried with 2 fresh new digitizers. Could it be that they are extremely sensitive on the inside? Or is it some glitch somewhere?
Extremely frustrating!
Sent from my HTC HD2 using XDA App
well mine is in the scrapped now. when my digitizer arrives and i sort things out i will get back to you
Hi, I bought HD2 with broken digitizer, so after it came to me I immediately buy new digitizer, didn't look for the cheapert but once again I resolve myself to never buy things for china digitizer doesn't work so I need to new one from USA, send it to my friend and he repair it within day, now everything work... and yes digitizer are very sensitive

HTC HD2 Touch screen stopped working

So I bought a HD2 with bad touch screen. The issue was the very common one that every one knows, red button that was poking into the touch screen flex cable. I opened up the phone and fixed the issue and touch screen was working perfectly fine. In the process, unfortunately, I chipped a little edge of the front glass/digitizer. It was not a big deal as phone was still working fine. But I decided to buy a new front glass.
When my new front glass arrived, I separated the digitizer/front glass from LCD, but then half of my LCD got corrupted. So I ended up buying an LCD too!!!
Now comes the issue: when I put the phone together, touch screen doesn't work at all. I have tried all combinations of NEW / OLD digitizer and NEW / OLD lcd. Nothing works. I wonder if anyone can help me figure out why?
P.S. When testing, I happened to connect the phone to my 5w wall charger directly connecting it to power pins (without battery installed). Would that be why I lost touch? Is the touch issue now because of motherboard that was directly connected to adapter, not getting power from its designated battery?
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
b3rvirus said:
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
Click to expand...
Click to collapse
Yes I had tried the old LCD, and that didn't work either.
I installed a WiFi Keyboard on it.
Did you resolve this issue?

Categories

Resources