I was going to install the new MoNaCo Rom but I did the radio update first after I install the update my phone looked like it was going to reset, it turned off and never came back on. My battery was fully charged and I just can't seem to get it back on. I pressed the power/home buttons and that doesn't turn it on either HELP!!! Is there anyway I could do a hard reset or anything I can do to get it to at least power up?
Did you make wipe before update to the new radio?
ivanrod07 said:
I was going to install the new MoNaCo Rom but I did the radio update first after I install the update my phone looked like it was going to reset, it turned off and never came back on. My battery was fully charged and I just can't seem to get it back on. I pressed the power/home buttons and that doesn't turn it on either HELP!!! Is there anyway I could do a hard reset or anything I can do to get it to at least power up?
Click to expand...
Click to collapse
I suppose you have a GSM HERO and flashed it with a GSM Radio, right? If not (CDMA phone/GSM Radio or vice-versa) and it doesent boot up after taking out/reinserting the battery multiple times then it's bricked for good at this stage IMHO. JTAG should help, provided someone had documented the procedure for the GSM HTC HERO. Btw, it's MoDaCo, not MoNaCo
miragebg said:
Did you make wipe before update to the new radio?
Click to expand...
Click to collapse
There's no requirement to wipe before flashing a new radio, as the "wipe" doesn't effect the radio part of the ROM.
Regards,
Dave
I was doing the radio first then I was going to do the wipe.
ivanrod07 said:
I was doing the radio first then I was going to do the wipe.
Click to expand...
Click to collapse
You diddnt answer about which hero you have, cdma or gsm? and which radio did you use.
you probably pulled the battery out during the procedure. when flashing, you do a reboot after the recovery tells you to and you leave it for around 20 minutes and it will boot up completely. you should never interupt it during this 20 minutes
hi
i'm new here, and i have almost the same problem exposed 2 years ago here. i have updated the firmware of my hero gsm and all was good, but one i updated tne radio rom, the hero doesen't want to work, it boots but stops on the first screen. i pressed lots of time on home/back and power, it boots normally but stop at the first screen, as if the back button doesn't work, but two days ago, alla the buttons were working.
i hope you will show me a solution other than gtag for the moment.
thanks
should i do this post in an other subjet?
if you flash the wrong radio,it must broken ,can you enter fastboot? if you can't enter,you have to use jtag to fix it
I can JTAG the HERO and I'm in Texas if anyone needs help with these.
HI
Thank you for the answer, zhaominghao,
no, the fast boot is inaccessible. And concerning the Jtag, i gave the phone to some one to reapre it with it, but he told me that there is problems of connectors. is this true or there is annother reason? i dont really know, i hope i was able to try the jtag my self, but i dont have the device jtag. i hope i wil found a solution.
thank you again.
If you can't get into recovery to attempt a reflash then JTAG is the only option and if the shop said it can't be done... time for a new hero
If the phone has damaged JTAG points then it's a loss. If they are intact then it's fixable with JTAG.
Related
i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen. it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
any suggestions would be great, plz im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
EDIT: just for those coming to this ancient and recently revived thread, this (my) problem has been solved. altho there are other people now with similar problems
Have you tried re-flashing?
jim256 said:
i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen!! it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
can anybody help me???? PLZ im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
Click to expand...
Click to collapse
Do a camera power reset and try again.
i tried that and it didnt do anything at all. isnt that just where you hold the end key and the side camera key and stick the stylus into the hole?
if so, it have any different effect than the standard soft reset
AraqirG said:
Have you tried re-flashing?
Click to expand...
Click to collapse
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.
jim256 said:
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.
Click to expand...
Click to collapse
Hold down the power button and the camera button at the same time until the tri colored bootloader comes up. If that works, try flashing the stock rom for your carrier.
If that doesn't work try the same steps with the memory card removed.
If that doesn't work try to do a hard reset and see if that will take you to the bootloader.
Also, what are the numbers in on the bootloader...are you sure your device is unlocked? I believe it should say... SPL-00.40.coke... on the 2nd line if your unlocked.
You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.
sorry i wasnt saying i needed to connect to activesync to reboot, i was saying i needed to connect to activesync to flash, and it wouldnt boot up so i couldnt get to activesync.
and i did to imcokemans unlocker, and everything went fine. when i was setting up the device (ie. setting password, time zone, calibration, etc...) i just decided that i didnt need to finish that as i was intending on flashing a custom rom anyway, and so any settings i put up the time to set would be erased.
having said that, i went ahead and starting flashing a custom rom right from the wm welcome screen that you get on a first boot.
thanks a LOT for your help, promptness, and attention
So are you back up and running?
well, now i am. i just took a 30 min drive down to the sprint store and got a replacement :S
thanks a lot for your help though, im scared i may really need to refer back to this thread later. but if i do, at least i know i should be able to fix it!
thanks.
well, i just did it again. i must be doing something wrong in the cooking of my ROMs...about to try out your solution..hope it works!!
wish me luck :S :S :S :S
well i was able to re-flash, but, unfortunately, it is stuck in the same "htc smart mobility" screen again. i think i have been able to narrow it down to the oemizer app. i must be doing something wrong in there.
oemizer http://forum.ppcgeeks.com/showthread.php?p=100746&referrerid=10115
ill keep cooking and trying tonight until i find what it is the problem is i guess, thx for your help guys. especially you 360discgolf.
well, after cooking and flashing too many times to remember this late, all i can do is ask for help when you guys wake up and check this thread.
in the last couple of builds i havent been doing anything with oemizer at all and it still hasnt been working, and i dont think i am doing anything extra in buildos that i havent done before in successful ROM images...it seems sort of erratic.
any suggestions/hints/comments would be great, thanks a lot.
you can't just hold the two buttons and press the reset. You have to hold the two buttons at the same time, then while holding them, use the stylus to hold the reset until it restarts. If you just tap the reset button while hold, it doesn't work.
360discgolf said:
You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.
Click to expand...
Click to collapse
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!
vkolas said:
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!
Click to expand...
Click to collapse
what carrier are you?
EDIT: also:
1) what os version are you running? (build number)
2) what radio are you running?
3) what bootloader are you on? (can be accessed via holding power + camera button and poking reset hole)
4) what are the orange numbers in the very bottom right of the screen when you are booting up?
these kinds of things all need to kind of jive for the sleep function to work correctly
jim256 said:
i used imcokemans unlocker (which i have done before) ...
Click to expand...
Click to collapse
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.
denasqu said:
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.
Click to expand...
Click to collapse
haha sorry this is a problem that i had a VEERRRRY LONG time ago. have learned a lot since since then, now it is this other fella here we are trying to help him
thx tho!
I've got a "Brick" HTC Magic - Vodafone.
Basically, when i press the power button doesn't start. It happened after follow the "Install / Update SPL" ( http://code.google.com/p/android-roms/wiki/SPL ) guide.
Is there any way to recover it? or should i put it on the bin?
You're going to have to be more specific than "it doesn't start".
Does it turn on? If so, does it hang at the htc magic screen? Can you hold vol-down and press power (while still holding vol-down) and load a screen with three androids on skateboards? If you can do the last step, it's not bricked, and you should look at the thread I have below about bricking and semi bricking, one of the users on there gave a great amount of information on what you can do if your phone's not working right (bricked).
Caid.
444
Caid444 said:
You're going to have to be more specific than "it doesn't start".
Does it turn on? If so, does it hang at the htc magic screen? Can you hold vol-down and press power (while still holding vol-down) and load a screen with three androids on skateboards? If you can do the last step, it's not bricked, and you should look at the thread I have below about bricking and semi bricking, one of the users on there gave a great amount of information on what you can do if your phone's not working right (bricked).
Caid.
444
Click to expand...
Click to collapse
Hi Caid, thanks for the reply! sorry for the short message without details.
Here is the answer for your first question (sadly, the rest of questions can be skipped):
Does it turn on?
It doesn't
It was after follow the guide i mentioned before. I tried to update the SPL, but something went wrong and my phone didn't turn on again.
So... I think I have to accept the fact is not going to work again.
Is there any kind of service able to fix this?
Anibal
No display at all? no backlight on the screen? no vibration (signifying it's past a certain point in the loading stage)?
You probably tried taking out the battery for 10 seconds and then putting it back?
As Caid444 asked, tried holding Back+Power for a few seconds (after making sure power is off and not just hanging. Take off battery for 10 sec and reload)? Tried holding Home+Power after making sure power is off?
please i need some help htc touche cruise
hi everyone. I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help
parrot5 said:
No display at all? no backlight on the screen? no vibration (signifying it's past a certain point in the loading stage)?
You probably tried taking out the battery for 10 seconds and then putting it back?
As Caid444 asked, tried holding Back+Power for a few seconds (after making sure power is off and not just hanging. Take off battery for 10 sec and reload)? Tried holding Home+Power after making sure power is off?
Click to expand...
Click to collapse
I'd really like to say it DOES something... but it doesn't . I tried Volume down + power, back + power and several more combination always taking out the battery and putting it back.
It's bad... Do u know if there's any hardware service for this?
Just a wild guess, but since the phone sucks more battery, then a vampyre on rampage.
Could it be an idea, to charge the battery before, or have the usb cable pluged in, when you press back+home? (the same buttons you used to enter fastboot)
I'm pretty sure what you're trying to say is, you know enough about the phone to know how to bring it into it's multiple boot options, and none of them make the phone even burp. So there's no need to tell you to press this button plus that button, or insert usb or remove usb, or battery or such, because you've already done all that.
Well, I'd have to agree with you that it's dead. Unfortunately, there's nothing to do at the moment. I'm guessing (or maybe just hoping) that in the future there will be an unbricker for our phone, much like those available for many htc branded winmo phones. In the meantime, how old is your phone? Can you still bring it back?
Caid.
444
p.s To anyone else who's trying to figure this out, let's assume that he's already tried the many variations of recovery procedures and that it's still not working.
argc79 said:
I've got a "Brick" HTC Magic - Vodafone.
Basically, when i press the power button doesn't start. It happened after follow the "Install / Update SPL" ( http://code.google.com/p/android-roms/wiki/SPL ) guide.
Is there any way to recover it? or should i put it on the bin?
Click to expand...
Click to collapse
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade? (I hope you didn't try to flash a G1 SPL on your Magic...).
Amon_RA said:
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade?
(I hope you didn't try to flash a G1 SPL on your Magic...).
Click to expand...
Click to collapse
That's how my brick arrived ! Tried Hard SPL, after installing the one you suggested. Yours okay, Hard SPL no. But even after installing the spl, no fastboot adb.
BRICKED by HARD SPL ( the recommended )
Same here, I have just bricked my new vodafone HTC Magic (Vaffanc...)
downloaded from here: http://code.google.com/p/android-roms/downloads/list?q=label:SPL
I hope something can be done. It is not reacting to power button at all.
Amon_RA said:
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade? (I hope you didn't try to flash a G1 SPL on your Magic...).
Click to expand...
Click to collapse
I think you are right, I have flashed the G1 SPL. But the page is really not clear, it start speaking as Dream/Magic and probably it is only for Dream. Since it says to apply the Hard Spl and in the download link(http://code.google.com/p/android-roms/wiki/SPL) there is no clue that it is not for the G2.
Any idea? anybody got it changed from the shop with no problems? (mine is vodafone in the netherlands)
Me idiot, I have to leave tomorrow for holidays!
byronhero said:
I think you are right, I have flashed the G1 SPL. But the page is really not clear, it start speaking as Dream/Magic and probably it is only for Dream. Since it says to apply the Hard Spl and in the download link(http://code.google.com/p/android-roms/wiki/SPL) there is no clue that it is not for the G2.
Any idea? anybody got it changed from the shop with no problems? (mine is vodafone in the netherlands)
Me idiot, I have to leave tomorrow for holidays!
Click to expand...
Click to collapse
as far as i can see no need to flash spl on vodafone magic. i have the same phone and all i did was root with Rav1.1.1G.img and flashed rom of my choice. you have flashed phone with g1 spl and it actually says g1 on the link you provided..........can't see how you missed it. with phone off press home+power button as that bring up recovery image. Rav image file is safer due to that. i am sure if hardspl was available for Magic it would be posted on here as a sticky
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
thanant said:
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
Click to expand...
Click to collapse
You did brick one with the hardSPL and now you bricked another with the same stuff? Didn't you learn the first time? Only way is to go back to the store and tell em you did it again.
thanant said:
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
Click to expand...
Click to collapse
It seems to me you need to go back to basics and start here
A noob question but what exactly does flashing a new SPL unlock.
I got my Vodafone UK HTC magic and simply Downloaded a 32B ROM and used nandroid backup to apply the update.zip and it installed fine and can use Root required apps.
hi all
My HTC magic was bricked after update SPL. Now when press power button, it stuck at HTC magic logo, anyone have solution for fix its?
I Can not understand how can this be possible. Why guys all of you, don't read before trying to change your SPL???? You even don't need any changes about it?! Why do you try to change the SPL? Do you know what that SPL does? I think most of you - don't.
My next question is why all of you are trying to flash the G1 SPL onto Magic phone? Are you crazy or what? There is NO HARDSPL for Magic (G2, Sapphire or whatever you want to call this device)!
The SPL collection is posted in this forum by Amon_Ra, and if someone want to change the SPL can do this by downloading some of the SPL collections posted here.
say2k said:
hi all
My HTC magic was bricked after update SPL. Now when press power button, it stuck at HTC magic logo, anyone have solution for fix its?
Click to expand...
Click to collapse
Power off your phone! Then press and HOLD the "back button", while holding it press once the red one(which you usually use to power on the phone). It will power on (i hope). If you get in fastboot mode then everything will be fine.
plz need help
while trying to update radio rom from sd card i bricked my hero
no powering up no charging led no connection to pc just like dead
need some help how much deep i amin s..t
Sorry about it but, its not "easy" to brick by flashing a new radio, unless wrong radio flashed or interrupted during flashing.
Some experts may be able to help if you put your question little more in detail...which radio etc.
update-hero-radio-63.18.55.06JU_6.35.08.29-signed
i was trying tp update this radio
hero-generic-2.73.405.38-rooted-signed firmware current FW
I had this problem as well what I did was contiously restart my phone take battery out put it back in. Done this like 20+ times then the phone managed to boot up.
Thanx but i already did that no use still dont know what s the problem
Htc hero bricked plez need help
i dunno whats wrong i was trying to update my radio rom minus nandroid backup
i flashed twice process stuck i pulled the battery now i have the dead phone no led no display no usb connection need help
Just checking but this sounds like you flashed a GSM radio onto a CDMA hero, is this what you have done? if so you are FOOOOOOBARRRRRRED son. and to be honest you really should have read about the radio flash.
If thats what it is,
if it isnt then good luck.
djmazhar said:
i dunno whats wrong i was trying to update my radio rom minus nandroid backup
i flashed twice process stuck i pulled the battery now i have the dead phone no led no display no usb connection need help
Click to expand...
Click to collapse
+ why do you think it got stuck? how long did you leave it?
List type of Hero you have, radio you were trying to flash aswell. Also will it boot into fastboot? (hold down vol down key and turn on)
Dan...
Thats what I asked in post 2.
i was trying to update radio rom 63.18.55.06JU_6.35.08.29
my SPL - 1.76.2007
rom -hero-generic-2.73.405.38-rooted-signed
and it does not boot into fast boot
Bricked htc hero some1 plz help!!!!
i have searched n searched online 4 2weeks for solutions but i have not found not 1 thing to help me,i accidentally flashed a gsm on my cdma & i cannot boot it @ aw,no led lights but yet it charges,i can only hold vol up & tap power & it juz vibrates 3x & i need some kinda of solution,anybody!please......
Hi all,
Maybe someone can help me out!
I am stuck at work - cant even really surf but had to post as I just feckered my mates HD2!
BOOOOO!!
So I installed HSPL and its still there.
Flashed up to energy ROM (APRIL 1st)
Then got stuck in reboot cycle - phone wouldnt boot unless it had power plugged in.
Took battery out of it and put mine in it which had higher charge - not much.
Then I got it booted into 6.5. Customised and changed settigns for Vodaphone.
Rebooted and phone stuck in loop again.
Couldnt get back into Vodaphone.
Went to bootloader and then used the official:
RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship.exe
Flashed the bugger.
Then tried to boot again.
No boot without power inserted
Phone will not complete boot even with power
gives HTC white welcome, shows ROM etc
vibrates backto HTC white welcome.
Rinse
Repeat
Can anyone give me any ideas what I can do with this? He is coming to get it at 5.30; I am meant to have FPSECE Morph gear and all sorts of other shizzle for him
He is going to get a brick
any ideas would be GREATLY welcome.
no flames please if I missed something, I am desperate to sort this quick and quiet.
Try make Task29 and then reflash Radio and ROM, it could help you i think...
Have you installed radio 2.08 ?
You should. You can install it by downloading it and use customRUU to install the file.
Put phone in bootloader first.
Your mate's phone will be revived
What radio do you have installed. The NRG roms require radio 2.08.50 in order to boot.
Yea sounds like a radio issue. You didn't mention what phone? US Tmo HD2 or everywhere else HD2?
Is GSM HD2
I have done all above task 29 new radio - loads of roms.....stuck in circle.
Phone will not boot without apower lead in it
Ahh feck [email protected]
What version radio does it read then when you are stuck in your bootscreen ?
is it still 2.06 or 2.08 now ?
Installing HSPL doen NOT upgrade your Radio.
What is your SPL version ?
And "fecking ass" is groce. Try fecking some koent.
lucid said:
Have you installed radio 2.08 ?
You should. You can install it by downloading it and use customRUU to install the file.
Put phone in bootloader first.
Your mate's phone will be revived
Click to expand...
Click to collapse
ClydeB1 said:
What radio do you have installed. The NRG roms require radio 2.08.50 in order to boot.
Click to expand...
Click to collapse
Actually they dont require 2.08... they require a radio without .51 numbering.
You can use
2.07.50.27
or
2.08.50.08
either will work just fine.
misticjeff said:
Actually they dont require 2.08... they require a radio without .51 numbering.
You can use
2.07.50.27
or
2.08.50.08
either will work just fine.
Click to expand...
Click to collapse
True, I use 2.07 (old signature LOL), but just mentioned 2.08 as it's the recommended one.
Oh ****e
Ok all,
Big warning to all here:
See my attached image.
I bent the left most battery connection pin out a tiny little bit - so little I didnt notice it.
Then the phone would obviouslly only boot without the power plugged in.
The pin was being pushed out! and not connecting with the battery.
I bent it back and it booted whilst I was explaiing that I was having teething trouble with his new ROM.
HAHA
Thanks VERY much to all for ideas and fast feedback - really thought I done it in then! Bloody hell Id have had to give him mine!!!
OH NOOOOOOOOOOO!!
@ the try some Koent line......OH GOD LOLOLOL
Waht with the relief of fixing the device and a joke like that, I was ROFL ing it - Not RALPH ing it...
Thanks again all
Yarod, the above advice for the radio version applies only to the custom rom.
By flashing a factory rom from the memory card you have probably overwritten hspl which is why this dosen't boot.
First thing to do is reflash hspl in the bootloader, via usb. If you remove your memory card and hard reset, then you should get a working phone. Assuming it's a vodafone branded handset you can use a vodafone branded rom without the need for hspl - there's a 1.66 version up on the uk site.
If you want a custom rom, use hspl and check the radio requirements before flashing
and most importantly flash via the usb only to avoid overwriting hspl.
hth,
mike
hah! bent pin, nice one. Bet you felt a huuuge wave of relief wash over ya when it booted eh? Gotta love that post adrenaline comedown.
here we go again with another victim....
1. Hard reset
a. turn off your HD2
b. hold Volume up and down and press end button till it will vibrate show white screen that you wanna hard reset
c. release volume up and down
d. press volume up for continue Hard reset
e. press volume up for continue boot up
it will boot up your device...
2. install radio for energy click here or herefor download
3. Use Customs RUU from here
4. flash your radio
5. now you are good to go....
i hope this helps i know how you feel cause i had same problem and this phone worth a lot so... take care...
yarod_g14 said:
Hi all,
Maybe someone can help me out!
I am stuck at work - cant even really surf but had to post as I just feckered my mates HD2!
BOOOOO!!
So I installed HSPL and its still there.
Flashed up to energy ROM (APRIL 1st)
Then got stuck in reboot cycle - phone wouldnt boot unless it had power plugged in.
Took battery out of it and put mine in it which had higher charge - not much.
Then I got it booted into 6.5. Customised and changed settigns for Vodaphone.
Rebooted and phone stuck in loop again.
Couldnt get back into Vodaphone.
Went to bootloader and then used the official:
RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship.exe
Flashed the bugger.
Then tried to boot again.
No boot without power inserted
Phone will not complete boot even with power
gives HTC white welcome, shows ROM etc
vibrates backto HTC white welcome.
Rinse
Repeat
Can anyone give me any ideas what I can do with this? He is coming to get it at 5.30; I am meant to have FPSECE Morph gear and all sorts of other shizzle for him
He is going to get a brick
any ideas would be GREATLY welcome.
no flames please if I missed something, I am desperate to sort this quick and quiet.
Click to expand...
Click to collapse
Hey! I did the same mistace, u need to download HSPLv2 , Install 2.06.0000
Then volume down + power botton, install stock ROM from HTC.com, and reboot.
That worked for me, hope it works for you.
Cheers.
lol
hi all this is fixed see my previous post, i had bent the battery pin - so small didn't notice it. i wonder if anyone else has suffered from this?
many thanks
i am tempted to fart in the general direction of the "another victim" statement
I'm a fixer not a victim lol...
yarod_g14 said:
hi all this is fixed see my previous post, i had bent the battery pin - so small didn't notice it. i wonder if anyone else has suffered from this?
many thanks
i am tempted to fart in the general direction of the "another victim" statement
I'm a fixer not a victim lol...
Click to expand...
Click to collapse
It just happened to me!! A billion thanks mate
Another reboot loop victim...
Bent battery pin seems to have been the culprit for me as well! sat on charge now to get it to 100% before I start reinstalling cabs and stuff.
Ok so i think i bricked my phone
Here's what happend:
My ROM was freezing up on me constantly so tried a different one, but had the same effect. MAGLDR 1.13 had problems booting and so had Clockwork.
So i figured i'd flash a winmo 6.5 rom to start all over. Now when i tried to flash the stock ROM i crashed at 8% i could only remove the battery, and now its unresponsive to everything, soft rest, boot into bootloader, normal boot, charging.
I really need my phone, does anybody have an idea?
Thanks.
Greetings.
i would pull your battery
hold down volume down and red power buttone then install battery while holding
that should get you into bootloader screen
you should also post what you tried to flash and what phone u have to get to this point.
possibly get a battery thats charged completly to try
The battery trick didnt work.
I tried to get rid of MAGLDR by flashing this rom:
http://forum.xda-developers.com/showthread.php?t=623283
and then the dutch one.
At 8% of flashing, an error occured. Had to pull out my battery and my phone has not responded to anything since.
Still nobody with any ideas?
I know the help on this forum isn't much but come on, im really desparate over here.
Therk said:
Still nobody with any ideas?
I know the help on this forum isn't much but come on, im really desparate over here.
Click to expand...
Click to collapse
...when you are not able to get to the tri color bootmenu by holding volume down while starting your phone then your phone is bricked.
The only way to unbrick it, is to use a jtag adapter..not very cheap, about 200$ and more!?
Sent from my HTC HD2 using XDA Premium App
At 8%, it's flashing the radio/SPL/etc (the important stuff). Plug it in to the charger. Any lights at the top? If not, bricked.
Problem you have is sort of referred to as "stuck radio ",,,,(mostly by me, to be fair) and you aren't getting answered because there seems to be no real fix for it. Some have managed after much trial and error to get a radio to flash, but most cases seem to end with nothing but JTAG or new mainboard.
Something that came up recently was flashing the 2.07.51 radio (not for tmous phones! ) so you could give that a try. Be interested in your results.
you could also try the "sd and sim and battery out, chill the phone in fridge/freezer,sealed in a bag, rom/radio image on the SD ready to flash" method. If this works then you have heat induced hardware failure.