Hello guys,
Since yesterday i experience a loss of calibration of my screen, when i touch an area it react 2 or 3 inch lower ou upper it makes me sick, i just cant answer a call, or do anything due to this chit, can someone handle this, it is ever happened to you?
up!!! help!
grafikastudios said:
up!!! help!
Click to expand...
Click to collapse
Not to state obvious but have you tried to recalibrate it? Or perform a hard reset?
Hi,
I have exactly the same problem, I did a recalibration and this is very strange, first when I finish the calibration, then it restart from the beginning and I have to recalibrate 3 or 4 times before it exit the calibration tool. Then the device works normally, but few minutes later, this is the same, recalibration is lost. I did a hard reset and even change the ROM, but it is the same.
I do not know what to do
I see also after a reboot, the calibration is good again, but this is not always the case.
What can I do ?
Thanks
Denis
morind79 said:
Hi,
I have exactly the same problem, I did a recalibration and this is very strange, first when I finish the calibration, then it restart from the beginning and I have to recalibrate 3 or 4 times before it exit the calibration tool. Then the device works normally, but few minutes later, this is the same, recalibration is lost. I did a hard reset and even change the ROM, but it is the same.
I do not know what to do
I see also after a reboot, the calibration is good again, but this is not always the case.
What can I do ?
Thanks
Denis
Click to expand...
Click to collapse
Sounds like a faulty device. Flash back to stock rom
& SPL if you haven't already and return under warranty.
Hi,
thanks for the answer.
I flashed back to the original ROM and I think this has also set the original SPL, but I am not sure. How can I check this ?
When starting up the device I can see :
R 1.13.25.24
G 52.62.25.34U
D 1.56 .00 .00
Is it correct ?
Thanks
Denis
morind79 said:
Hi,
thanks for the answer.
I flashed back to the original ROM and I think this has also set the original SPL, but I am not sure. How can I check this ?
When starting up the device I can see :
R 1.13.25.24
G 52.62.25.34U
D 1.56 .00 .00
Is it correct ?
Thanks
Denis
Click to expand...
Click to collapse
Go into bootloader to check SPL, i.e.
Turn off phone
Hold vol down
Turn on phone while continuing to hold vol down
You should enter a tri-colour screen. This is bootloader and it should state your SPL
ok, you're right, the SPL was wrong, I set it back to 1.13.
I resintalled the ROM and now I fell down on a loop in the alignement screen
I will send the device to repair...
thanks
Denis
morind79 said:
Hi,
I have exactly the same problem, I did a recalibration and this is very strange, first when I finish the calibration, then it restart from the beginning and I have to recalibrate 3 or 4 times before it exit the calibration tool. Then the device works normally, but few minutes later, this is the same, recalibration is lost. I did a hard reset and even change the ROM, but it is the same.
I do not know what to do
I see also after a reboot, the calibration is good again, but this is not always the case.
What can I do ?
Thanks
Denis
Click to expand...
Click to collapse
When you do a calibration, how accurately you tap the cross-hair dictates if the digitizer senses a second or third calibration is necessary. Most people tend to blow this off and use either a finger or fingernail to do the calibration. The digitizer gets the most accurate tap when a stylus is used. You might want to try using a stylus OR you can try the following modified registry hack which comes from this post: http://forum.xda-developers.com/showpost.php?p=4998396&postcount=1
REGISTRY HACK TO ELIMINATE EFFECTS OF FIRST CALIBRATION
Using your favorite Registry program, navigate to HKLM:
1. HKLM\Hardware\DeviceMap\Keybd
2. Look for the entry named: FirstCalibration
3. If it's there, you can do one of two things: first, delete it; or second, change the dword value from 1 to 0.
4. If entry does not exist, you can create the dword FirstCalibration and give it a binary value of zero
5. Do a soft reset. It is recommended that a manual soft reset using your stylus is used as opposed to a softreset program. I have tested this hack on my device. As per the original post, some soft reset programs would not allow the Registry hack to take.
It is implied (or maybe I read it in a subsequent reply to this post/thread) that most digitizers are accurate enough without a calibration. Should you find that your screen when tapped is not accurate, you can always do a screen calibration later.
Historical Info
When PDAs first came out, digitizers were not as accurate as today's versions which mandated calibrations. Often on my first iPaq, which I bought when Compaq first built them, two or more calibrations were necessary because the digitizers were of poor quality. Part of the initial first set-up screen was a mandatory calibrate screen.
A Compaq engineer I chatted with stressed getting the first two if not all four taps as accurately as possible. He claimed that if all four were done in the center of the cross-hair's dot, a second calibration would not be necessary. What ticked me off is that the second calibration tap is often obscured or hidden by the onscreen words of the calibration statement.
Current Info from three smartphones
With today's digitizers, I have never had to calibrate my Dell x51V Axim. In fact on three smartphones I have either purchased or helped with the purchase thereof, I have never seen a calibrate screen when the phone is initialized out of the box new. The only time I have a calibration screen is when a Mass Clear is performed or the ROM is restored off the SD card.
Based upon usage, I believe that today's digitizers accurate out of the box and that the problem may be caused by either flashed ROMs or apps that are causing interference.
Try the hack and see if that works. Good luck and we're all counting on you!
Hi,
Unfortunately, i think the problem is hardware. I always use the stylus for calibration. Now I can't go out of the calibration window...
And this is not a ROM issue as I flash the original one from HTC, and during the fist boot, it ask for the calibration and I can't go further (loop in this tool).
I will send my device to repair... it is on warranty.
Thanks for the info
Br,
Denis
morind79 said:
Hi,
Unfortunately, i think the problem is hardware. I always use the stylus for calibration. Now I can't go out of the calibration window...
And this is not a ROM issue as I flash the original one from HTC, and during the fist boot, it ask for the calibration and I can't go further (loop in this tool).
I will send my device to repair... it is on warranty.
Thanks for the info
Br,
Denis
Click to expand...
Click to collapse
I think in the thread I quoted there is a way to break out of the calibration screen which makes it skipped. Since it will take you a day or two to get the device ready to be shipped or repaired, you could read that thread as the Registry hack could be the trick. . .
thanks man ill try this and anwer back in hours
Wow i've made teh replacement in reg, it is worst, and after nother hard reset it kept the same values in reg, how can i o a complete flash, with all settings back to defaults ?
I had exactly same problem and I sent my device to repair ... they changed touchscreen and now it's ok
Have u tried re-calibrating it? if you cant go to the menu because of the loss of calibration just hold Up + Down of the volume keys and then tap the screen. (this is do be done while phone is already on)
Related
Why is that? Since I upgraded to WM6, and I remove the battery the clock resets to 12:00 in 2004
that's basically the only weird thing I have with wm6 on the blue angel so far... what an upgrade
I think it could be, because when you remove the main battery the backup doesn't last very long (20 mins max last time i checked in the manual).
How long do you remove the main battery for?
Steve123456 said:
I think it could be, because when you remove the main battery the backup doesn't last very long (20 mins max last time i checked in the manual).
How long do you remove the main battery for?
Click to expand...
Click to collapse
2 seconds to switch sim card
Just test on my: remove battery, wait 20sec, reconnect (no R G), soft reset, everything OK on date/time.
Maybe your backup battery is dead?
DANDANA said:
Just test on my: remove battery, wait 20sec, reconnect (no R G), soft reset, everything OK on date/time.
Maybe your backup battery is dead?
Click to expand...
Click to collapse
why do you softreset after removing the bat..?
edit: just tried it again, reset again... backup battery was fine on wince3... it's at 100%
ow well, I can live with it, it's not that I remove the battery all the time, and active sync adjusts the clock anyway...
No R G on the boot screen...just to get my radio back
DANDANA said:
No R G on the boot screen...just to get my radio back
Click to expand...
Click to collapse
yeah I've noticed that too on my test qtek... but on mine it's always there
to save you the hassle of manually changing the time/date or docking it in the crade, try this:
1. soft reset. as soon as you see the 4-color screen (DO NOT WAIT for the R, G, and D values to be shown), remove the battery.
2. replace the battery
3. turn on the phone. soft reset. when you see "none" values for R and G, soft reset again.
the time/date will be retained.
Hi there,
I have the same issue. In fact, each time I remove battery, even for 1 sec, I lose Date/time and "lock buttons" setting. Nothing else.
I tried what you said, but nothing changed. I just noticed that the "R None" comes directly after I turn on the phone (your 2nd step).
I am doing something wrong ?
i missed some steps. before you remove the battery, you should not wait for the RGD values to be shown... it should be only the 4-color screen.
raymonds said:
i missed some steps. before you remove the battery, you should not wait for the RGD values to be shown... it should be only the 4-color screen.
Click to expand...
Click to collapse
ok... that actually works... so I have to do that every time I want to remove the battery safely?
thanks for the help.
A--
tjacquem said:
Hi there,
I have the same issue. In fact, each time I remove battery, even for 1 sec, I lose Date/time and "lock buttons" setting. Nothing else.
I tried what you said, but nothing changed. I just noticed that the "R None" comes directly after I turn on the phone (your 2nd step).
I am doing something wrong ?
Click to expand...
Click to collapse
yes indeed, it's the Date/time and the lock buttons, and any buttons you redefined (I always redefine the record button as screen rotate button)...
but that's all fixed now
It works for me when I follow the steps exactly as described. Thanks Raymonds - it saves me from the pain of reloading all my apps and syncing up with exchange... which I've done may be 4-5 times already.
This should be added to WIKI IMO
yes, i guess it should be in the wiki. please feel free to place it there (i don't know how... i might mess it up)
i happened to come up with this combination by accident... crude, but effective.
tjacquem said:
I have the same issue. In fact, each time I remove battery, even for 1 sec, I lose Date/time and "lock buttons" setting. Nothing else.
Click to expand...
Click to collapse
Probably you are loosing:
- wifi settings (paswords etc)
- bluetooth pairing
too
It looks like part of Hard Reset procedure, but without clearing registry not memory.
But hard reset doesn't clear "button lock" settings
I have no problem with data / time, but could anyone tell me what "R none" and "G none" means? I had this problem since yesterday. I switched on my phone: softreset. Then the two "none" values. And I couldn't phone anyone. I already thought that I had erased my Radio ROM somehow.
Now I read your instructions: softreset, battery remove immediately, battery in and again softreset. Now I have correct values in "R" and "G", but my phone says "SIM card not valid". Hmm....
Has someone an idea?
Thank you,
Alex
EDIT: After this procedure I loose my date/time settings. But this is no problem, I just want to get my phone back
EDIT2: I removed the SIM again and put the battery in, then again R and G "none". After a softreset, the values are back. But still (without SIM) it says "SIM not valid". When I tap on the digits, it thinks I want to enter a PIN (and I have no PIN)...
Alegra, the "NONE" issue is caused by the bootloader going to quickly, so the radio has not been initialized by the time the OS starts to query it. If the OS boots up, there is effectively no radio for it to use. I'm not sure why this causes settings to be lost, possibly just bad handling of the error condition.
Basically, whenever you replace the battery you should be prepared to hit reset once the four bars appear. This needs done every time you do this.
raymonds said:
to save you the hassle of manually changing the time/date or docking it in the crade, try this:
1. soft reset. as soon as you see the 4-color screen (DO NOT WAIT for the R, G, and D values to be shown), remove the battery.
2. replace the battery
3. turn on the phone. soft reset. when you see "none" values for R and G, soft reset again.
the time/date will be retained.
Click to expand...
Click to collapse
I am a heavy user of two batteries, isn't there a permanent fix for this? I am sure the M$ didn't design their new OS for battery devices that loose settings when the battery is removed.
I also use more than one battery. Always having to reset the date and time is cumbersome. Has there been any resolution?
After upgrading to WM6, every works perfectly. But then, it seemed randomly, the display is blank/ all white, but I can the phone is still functioning, because i can tap on the screen and get the tap sound. Soft reset and hard reset doesn't work. I'm doing the hard reset blindingly since the display is showing nothing, guessing the key push (i pressed record-camera 3x then mail button). I'm pretty sure it did the reset because after about 30 secs I get the beep that comes on when the screen is showing Tap to setup your device.
I figured it might be a loose lcd cable, but if go into the bootloader, power+record+reset. The display works fine! Showing Serial V 2.07.
I took apart the BA anyways and made sure the lcd cable is firmly attached. It didn't work.
Sometimes the phone would go back to normal randomly, or if I let the backup battery drain, but not always. When it goes back to normal, the clock is always reset to 2004 12:00 AM.
Can anyone help me? Is it possible to have a loose LCD connector which won't be able to show normal display, but can show the bootloader normally? Or is it caused by something else?
Here are other things about my BA that may or may not be related to the problem:
-Can't use DOC_Repart to resize storage, I'm getting the FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed as described here http://forum.xda-developers.com/showthread.php?t=255585
-When upgrading the upgrade program can't detect my current OS version (showing blank under "Your device is about to be update from:"), but otherwise the upgrade works fine.
-I tried Helmi R0, PDA Viet , and xplode's 6.00 roms. They all give me the same problem
Thanks.
I am also experiencing the same issue... currently phone is at white scren, but using My Mobiler i can see my desktop and see that the phone is fully functional, just white screen so cant use...
Mine too. I can see the display working perfectly using SOTI pocket controller pro. So the phone seems to be functioning except for some reason the screen is showing all white screen.
cubangt, are using an extended battery or the standard battery that comes with the phone?
Have you tried flashing with a different rom??
Sorry, I fear my message won't be useful at all for you, but I'll post it just for the record. I hope you can find the solution to your problem anyway!
My BA now can't show anything but a white screen because of what I think is damage to the screen cable (while sliding the display the backlight goes on and off...).
But the cable is not loosely connected, it is sort of strongly bent at one point, and maybe some contacts got kind of cut. Now it does not work anymore, but some time ago switching it off and the on again used to do the trick: the display would be readable again (even though with annoying colours, stripes and so on). I don't think this is your case, but I'd like to warn the newbies like myself that they should care not to lose any piece while changing the LCD on their BA: I think I probably forgot about some sort of protection which could avoid damages to the cable in its movement.
As for the missing version number when upgrading, the same has always happened to me.. I think.
Ok, sorry for my English, I would have had some troubles with exposing these few silly things even in my mother tongue... bye... and good luck.
I tried 3 different WM6 roms. And if I remembered correctly this also problem also occurred for a brief while I downgraded to WM2003SE while trying to resize the storage(which failed).
Yeah I'm not sure if mine is a hardware problem, since I can always go into the bootloader and the display works fine there.
I have new info to add though. I found out I can reliably get rid of the problem by draining the backup battery. Now I have a new question, since draining the battery takes a while, is there a way to reset the phone as if the backup battery is emptied (and return my display to normal)? If I can find a way to simulate this, then I can actually use my phone again, even if I have to do this once a day.
Obviously soft reset doesn't work. And I don't wanna do a hard reset either. Maybe the experts here now what kind of data is reset when all batteries are completely drained.
Thanks for the help
hmmmm
quick thinking.....i was working on my phone tonight and came across this thread.....if not grounded properly it could be that you statically fried a component in the process?
Hello everyone:
I've found a failure on my blackstone's g-sensor.
I noticed it wasn't working playing Teeter.
I tried to configure with the tool provided in the ROM but une of the bubles (horizontal) always goes back to the right side.
Tried hard reset, but still got the problem.
Is there something like a driver that I could reinstall, or should I send it directy to HTC??
Thanks in advance
If HARD reset doesn't work, I would suggest sending it back for repair.
- Steve
Yes, HARD reset didn't work.
The SOFT reset was the first thing I tried...
¿Wouldn't be possible to reinstall the software that uses the g-sensor?
The hard reset restores your phone to the state it was out of the factory. No additional software to the preinstalled stuff is required for the G-sensor to work. If immediately after a hard reset the G-sensor still does not work, it's 99% a hardware problem. The reason why hard reset is suggested is to make sure that other software possibly disturbing what does not work (the G-sensor software in this case) are removed, but, again, out of the box the phone already has the software and drivers needed for each part of it to work.
By the way, the calibration error is a clear signal of the problem.
Well my friends...
The g-sensor failure issue has been solved without HTC's help...
Maybe using the Advanced Config tool, I changed the Gsensor value (don't know how to translate it, in spanish "Intervalo de muestreo del acelerómetro").
I set it in 200. Today, as my last attempt to solve it, I changed it again, to 150, and... et voila!!! It works!!!
The strangest thing is that I made several soft reset, even one hard reset (yes, a hard reset, I know how to do a hard reset), but it didn't worked.
It seems that some changes we make with this configuration tools, stay the way we set them, even if we make a hard reset... Is this possible?
Black Antitoon said:
If immediately after a hard reset the G-sensor still does not work, it's 99% a hardware problem.
By the way, the calibration error is a clear signal of the problem.
Click to expand...
Click to collapse
Definitely, I've found the 1% that always bothers us in computers...
I still tend to think that your sensor was "stuck" for some reason and after a bit of moving and shaking the device with normal use it got "unstuck". The stock settings are always correct for basic hardware features, and are the same for all users.
Black Antitoon said:
I still tend to think that your sensor was "stuck" for some reason and after a bit of moving and shaking the device with normal use it got "unstuck". The stock settings are always correct for basic hardware features, and are the same for all users.
Click to expand...
Click to collapse
Maybe you're right.
In fact, I've changed back the value back to 200 (ms.), and it still works...
But it didn't get unstuck by the normal use... I tried it several times. It happened only when I changed that value.
elmalomalo said:
But it didn't get unstuck by the normal use... I tried it several times. It happened only when I changed that value.
Click to expand...
Click to collapse
By doing a hard reset this value should be reset to default, so if you really did a hard reset, it probably wasn't a software issue at all.
I don't have any explanation. Maybe it was just a case that it got unstuck in that moment, maybe not, and changing the setting caused something in a microchip of the G sensor work again... No ideas.
johnpatcher said:
By doing a hard reset this value should be reset to default, so if you really did a hard reset, it probably wasn't a software issue at all.
Click to expand...
Click to collapse
Yes, a hard reset, switching on the PDA while keeping volume down pushed, as the user guide says...
I don't have any explanation. Maybe it was just a case that it got unstuck in that moment, maybe not, and changing the setting caused something in a microchip of the G sensor work again... No ideas.
Click to expand...
Click to collapse
OK, at least, if anyone reports same problem, this could help.
Hi,
I m facing the same problem as you described, my horizontal tube is stuck on the left side.
I tryed to change the polling interval setting without effect.
I discovered a weird (from my point of view) inside the registry. The calibrate2-? is set set at a very hight value (only 1 in binary).
Changing it by a registry editor doesn't work, it goes back to the weird value when i restart the device.
Can you tell me if you had such values when you experienced the problem ?
Thank you
Hi again,
You know what ? i m happy
It was a pure physical problem. I give on my touch hd a little pinch on the left side and it unstuck the problem.
Everyone must know that it can happen. No change inside the registry is needed. You just have to shake a bit your hd to make it work again (if you break it i m not responsible )
yann.gloriau said:
It was a pure physical problem. I give on my touch hd a little pinch on the left side and it unstuck the problem.
Click to expand...
Click to collapse
..............
I had this problem after I traveled in a bus on a bumpy road with HD in my pocket - No pressure fall or anything. I am surprised to see so many had his problem. Hard Reset was no use. I shook my HD vigorously and this solved it. I was worried if this baby gets a Shaken baby syndrome by the shake
Lol! You remind me of my car stand. Each time I am on my car with the HD on its stand, and I bump into a hole on the road, the screen rotates for a short while (due to the G-sensor). This is annoying, but funny... I think I will add TomTom to the exceptions list.
yann.gloriau said:
Hi again,
You know what ? i m happy
It was a pure physical problem. I give on my touch hd a little pinch on the left side and it unstuck the problem.
Everyone must know that it can happen. No change inside the registry is needed. You just have to shake a bit your hd to make it work again (if you break it i m not responsible )
Click to expand...
Click to collapse
Had the exact same problem, sensor was stuck on the left. I was about to retire the HD and go back to my rhodium when found this post.
Pinching didn't work but a minute of VIGOROUS shaking did the trick! Still looking for my stylus which flew out ... be careful when trying this at home children
Yay, my HD lives!
Please advice where can i find the advance config tool? i'm facing the same problem
rahilpatwa said:
Please advice where can i find the advance config tool? i'm facing the same problem
Click to expand...
Click to collapse
Here you go mate
rahilpatwa said:
Please advice where can i find the advance config tool? i'm facing the same problem
Click to expand...
Click to collapse
It sounds like the less Advanced tool also does the trick - just give it a vigorous shake
Cero92 said:
Hi all, i just got a Qtek 9090 with WM2003 (ITA). I upgraded to WM6.1, but now it has some strange problems: first of all, when it goes in standby, sometimes it doesn't wake up. If i have to reset it, most of times it doesn't boot (it shut down before WM loads) or i get R: None G: None and i have to reset again (otherwise the phone won't work).
The lock at the boot doesn't happen when the phone is connected at the USB port (i think that's because it charges, maybe it's a battery problem?)
Another thing is that i can't turn it off: if i hold pressed the power button, it deactivate the backlught but the device stays on, and if i make another long press, i get the backlight back again... I had this problem also with WM2003, maybe it's normal?
What do you think? Whan can i do?
Click to expand...
Click to collapse
Have you make a HardReset?
The correct HardReset, not only reset and press Power button!!!
See in my HowTo Section...
and why not WM6.5.5 see here
yep, hard reset is a good start, but about your other problems:
the device does not really turn off, like other phones. pressing the power button makes it go to hibernate, the display turns off, depending on your settings, it locks the hardware buttons and it shuts off wi-fi, it hardly uses any energy but gsm/gprs stay on.
the device seems to be off, yet the phone is one and you can be called. that is the closest you get to switching it off. when you turn on airplane mode, the battery consumption is even less so there is not really a need to turn it off.
pressing and holding the power button always was for the backlight. many other devices open up a shutdown menu when you do that, that would allow you to turn it off, soft reset, or switch off the backlight, but for the BA, that is not the standard. however, if i read it right, d-two is working on remapping the power button, probably for that cause.
the R: none G: none issue is known and not a problem with your phone, whenever you run out of power or remove the battery for a second, the next boot will be w/o radio (R and most roms don't allow booting without it. that's why you get stuck there and have to perform a soft reset. back in the days of wm2003 i used to remove the battery when the device froze to reset it w/o the stylus, because it didn't matter then. with cooked roms, it is different, just like the booting splash screen or the way to perform a hard reset, many things change on a cooked rom.
the issue with waking up from standby, or the SOD (standby of death) is an issue, that most likely has something to do with a backup, restored after flashing another os, or maybe you didn't perform a hard reset, as stated by d-two. you should do that, now that the device is still new, you have nothing to lose
also, read through the tutorials posted by d-two and myself, whether you missed anything while flashing.
The "real" hard reset is the one i can get by pressing camera + record button and reset? If so, i already did it after flash (i use d-two 6.1 Manila ROM in WWE)
It shows me 3 options, i put on YES "Clean Registry Hive" and "Format Storage" then i press the mail button, the screen become white for a while and the next boot al seems to be ok.
It seems, because after some time i get again the "standby of death" and, if i press the reset button, the most of time it won't boot up again (it turns off before i can get to WM), if it works phone doesn't. All these boot problem can be avoided by connecting the phone to the usb cradle, so maybe it's also a battery problem, i think...
@ d-two: i'll try your new ROM, however before i've tried your 6.1 ROM
I've already read your guide because i've got Windows 7 and i couldn't flash without your tutorial
NEWS: installed d-two new ROM, after flash i made the hard reset selecting the second and the third options, then i get the blank screen and, when viewing the htc screen, it shut down itself like it did before
As always, with the usb connected, it has no problem :\
It can be battery power - battery is old, and it doesn't provide current [A], or voltage drops [V] and phone think, it's empty.
Maybe you can try with new battery, or buy 2 nokia bl-4c batteries and repair orginal battery (somewhere on forum there is a tutorial about that - but use bl4c, not bl5c like in tutorial - bl5c are too thick to fit)
n0rbi666 said:
It can be battery power - battery is old, and it doesn't provide current [A], or voltage drops [V] and phone think, it's empty.
Maybe you can try with new battery, or buy 2 nokia bl-4c batteries and repair orginal battery (somewhere on forum there is a tutorial about that - but use bl4c, not bl5c like in tutorial - bl5c are too thick to fit)
Click to expand...
Click to collapse
That's what i was thinking (and that's i hope it isn't)... Now with another recharge cycle it seems to be good also with cooked ROMs, i hope it's solved
Maybe you just have to charge/discharge it for 4-5 times, and it will restore it's capacity. Mine BA was turning off when battery indicator was showing ~60-70%, and now I'm waiting for new battery (i destroyed original )
"charge/discharge it for 4-5 times" does not have an effect on Li-ion kind of batteries. This is probably a software problem. When you turn your phone on (after removing a battery) it always shows "None" for R and G, so just press Reset button and it will be ok. I use Reset to power it on Then you can flash 6.5.5 which doesn't have problems, and do a hard reset. There should be no problem at all..
I also got the problem with the stock ROM :\
The R: None G: None error is the less important problem
Got any luck fixing it? I've had similar problems before, sometimes it turned itself off when the battery was at 60% in WM2003. Did you update to d-two's 6.5.5?
Yes, now i'm running d-two's 6.5.5 ROM.
No, i still had the problem Yesterday i called to the assistance service and they said me to remove the battery and after a while recharge it.
I put off the battery yesterday at 16 and i put it again in the phone this morning at 8, i charged it but i still have the problem
This evening i called again and they said me that i have to send it back, i'll flash the original ROM and send it on monday.
That's a shame, i really like this device, even if it's not mine, my sister uses it and she's not a pro user, what a waste
Didn't understand, what "assistance service"? This is very old phone, I just can't believe it has some kind of warranty
I have another battery, and using it the device turns it off sometimes while it's in the stand-by mode! Don't know why, the voltage on it is fine, I have measured it while working...
marko_serb said:
Didn't understand, what "assistance service"? This is very old phone, I just can't believe it has some kind of warranty
I have another battery, and using it the device turns it off sometimes while it's in the stand-by mode! Don't know why, the voltage on it is fine, I have measured it while working...
Click to expand...
Click to collapse
I bought it on an eBay market and it offered 60 days warranty. It's not official HTC/Qtek warranty, but it doesn't make difference, as long as the device will work
If for you it happens only when it's in standby, maybe you just have the standby of death, the problem Chef Tony was talking about at post 3?
Cero92 said:
I bought it on an eBay market and it offered 60 days warranty. It's not official HTC/Qtek warranty, but it doesn't make difference, as long as the device will work
If for you it happens only when it's in standby, maybe you just have the standby of death, the problem Chef Tony was talking about at post 3?
Click to expand...
Click to collapse
My Roms have no SOD
This is when vbase32 have all 01000000 base adress !!!
Search about SOD!!
No, this happens only with my old battery. I'll try it out now with this new ROM!
I was trying to understand his problem
Just to know, what kitchen do you use?
Cero92 said:
I was trying to understand his problem
Just to know, what kitchen do you use?
Click to expand...
Click to collapse
First i have create my own kitchen but then i have found the OSBuilder and this is the best kitchen ever
With this kitchen you can look the Vbase32 for SOD!!!
Well, i trust you that your ROMs doesn't have SOD problem, in fact this happened to me also with the shipped WM2003 ROM, it's a real hardware issue
Cero92 said:
Well, i trust you that your ROMs doesn't have SOD problem, in fact this happened to me also with the shipped WM2003 ROM, it's a real hardware issue
Click to expand...
Click to collapse
I think so, sorry
d-two said:
I think so, sorry
Click to expand...
Click to collapse
No problem, i'll send it to the assistance on monday, i hope it won't take too much time :\
Cero92 said:
No problem, i'll send it to the assistance on monday, i hope it won't take too much time :\
Click to expand...
Click to collapse
good luck But very cool that you have warranty
Hello you all
I've got a strange problem with my HDmini :
Sometimes, the screen stops responding !
I can touch any button, the screen in any place, nothing happens.
I only have to remove the battery ( because thre is no reset ).
After strated again, when PIN code is asked, if a tap on "3" for exemple, it is like if i have tapped on "6" ; if i tap on "erase", i see "cancel" highlighted !
And after a few minutes, everything becomes normal again.
An idea ?
Did you install any cab or custom settings?
Yes, i'm using throttlelauncher with WP7 theme but when the screen is stuck, i have two choices :
Remove the battery to start again, without throttlelauncher started .
Restart the HTC with Mymobiler if the HDmini is connected.
At the end, the problem stays on.
I only have to wait for some time and then the touchscreen works again... by itself !
I haven't tried Throttlelauncher yet. I don't know if that can be the possible culprit.
Bart3385
For example, yesterday and today everything was OK and 5 minutes ago, the screen has stuck again !
Nothing possible to do on the screen neither with the 5 keys at the bottom !
I have to connect the HDmini to the PC and reboot it with my mobiler;
then i can use the screen interface.
It seems that the problem is the touch screen !
francois64 said:
Bart3385
For example, yesterday and today everything was OK and 5 minutes ago, the screen has stuck again !
Nothing possible to do on the screen neither with the 5 keys at the bottom !
I have to connect the HDmini to the PC and reboot it with my mobiler;
then i can use the screen interface.
It seems that the problem is the touch screen !
Click to expand...
Click to collapse
Try to ask for a new device (if it's still under warranty )
bart3385 said:
I haven't tried Throttlelauncher yet. I don't know if that can be the possible culprit.
Click to expand...
Click to collapse
Maybe your device is blocking so hard that your keys and screen both don't work anymore. I have had that too once Maybe Trottle causes this?
Madmatt
The problem is to be sure that a software is the problem origin; before i ask for the PDA to be replaced by my operator.
Try to do hard reset. Install only the basic stuff. (Minus Throttlelauncher.) See if the phone goes back to normal.
_Madmatt said:
Try to ask for a new device (if it's still under warranty )
Click to expand...
Click to collapse
That's a possible option.
Somehow, i'm not allowed to make that kind of suggestion anymore. Someone keeps on following me and make a mockery whenever i mention anything like that.
Anyway, try to check software problem first. As i first did on my own device. Before i've ascertained it is defective hardware.
francois64 said:
Hello you all
I've got a strange problem with my HDmini :
Sometimes, the screen stops responding !
I can touch any button, the screen in any place, nothing happens.
I only have to remove the battery ( because thre is no reset ).
After strated again, when PIN code is asked, if a tap on "3" for exemple, it is like if i have tapped on "6" ; if i tap on "erase", i see "cancel" highlighted !
And after a few minutes, everything becomes normal again.
An idea ?
Click to expand...
Click to collapse
It is normal, sometimes, it doesn't respond, lame htc hd mini. I have this problem long ago.
Thank's for your suggestions.
Today, the phone is completly stuck.
That's why i don't think it is a software problem.
I can' even entry the PIN code.
i've tried a Hard reset, to flash back to Original Rom = nothing more.
So i've asked Orange for an exchange under garanty...
That's a good move.
In some areas, a high percentage of units need replacement.