Related
all i get is the telus boot screen and thats it. is there anyway to flash the rom onto it? or restart it some how?ive tried to take out the battery and restart it that way and still boot screen.
I think you can do a hard reset by holding the "power button", "end key", and pressing the reset "pinhole" at the same time.
foxatphoenixlabs said:
all i get is the telus boot screen and thats it. is there anyway to flash the rom onto it? or restart it some how?ive tried to take out the battery and restart it that way and still boot screen.
Click to expand...
Click to collapse
have you tried getting into bootloader by pressing power/camera/reset?
when did this start happening?
The same thing happened to me today... Im frozen at the htc smart mobility boot up screen and nothing works!
if your phone was older and you tried to flash a GPS rom without installing the GPS radio then you would freeze up a the bootscreen
the remedy for that would be to install the 3.42 radio ROM
raybond25 said:
if your phone was older and you tried to flash a GPS rom without installing the GPS radio then you would freeze up a the bootscreen
the remedy for that would be to install the 3.42 radio ROM
Click to expand...
Click to collapse
I think I have same problem.
Anyone have a link where I could find that & install instructions to make sure I don't screw up more?
This happened to me too. I ended up having to reflash it like everyone said.
My htc hd2 is stuck on the boot up screen,tried pressing the end key and the red reboot button at the same time but still no progress,still stuck.....what now? help please
Hannoe said:
My htc hd2 is stuck on the boot up screen,tried pressing the end key and the red reboot button at the same time but still no progress,still stuck.....what now? help please
Click to expand...
Click to collapse
You are in the wrong section altogether. Go to this part of the site http://forum.xda-developers.com/forumdisplay.php?f=631
@OP,
First things first, did you unlock the device before flashing? Also, are you sure that you have a Vogue and not an Elf/Elfin?
A quick way to get out of your issues would be to try to flash the phone back to stock. Put the device in bootloader mode and flash a stock rom for your device.
I've got a "Brick" HTC Magic - Vodafone.
Basically, when i press the power button doesn't start. It happened after follow the "Install / Update SPL" ( http://code.google.com/p/android-roms/wiki/SPL ) guide.
Is there any way to recover it? or should i put it on the bin?
You're going to have to be more specific than "it doesn't start".
Does it turn on? If so, does it hang at the htc magic screen? Can you hold vol-down and press power (while still holding vol-down) and load a screen with three androids on skateboards? If you can do the last step, it's not bricked, and you should look at the thread I have below about bricking and semi bricking, one of the users on there gave a great amount of information on what you can do if your phone's not working right (bricked).
Caid.
444
Caid444 said:
You're going to have to be more specific than "it doesn't start".
Does it turn on? If so, does it hang at the htc magic screen? Can you hold vol-down and press power (while still holding vol-down) and load a screen with three androids on skateboards? If you can do the last step, it's not bricked, and you should look at the thread I have below about bricking and semi bricking, one of the users on there gave a great amount of information on what you can do if your phone's not working right (bricked).
Caid.
444
Click to expand...
Click to collapse
Hi Caid, thanks for the reply! sorry for the short message without details.
Here is the answer for your first question (sadly, the rest of questions can be skipped):
Does it turn on?
It doesn't
It was after follow the guide i mentioned before. I tried to update the SPL, but something went wrong and my phone didn't turn on again.
So... I think I have to accept the fact is not going to work again.
Is there any kind of service able to fix this?
Anibal
No display at all? no backlight on the screen? no vibration (signifying it's past a certain point in the loading stage)?
You probably tried taking out the battery for 10 seconds and then putting it back?
As Caid444 asked, tried holding Back+Power for a few seconds (after making sure power is off and not just hanging. Take off battery for 10 sec and reload)? Tried holding Home+Power after making sure power is off?
please i need some help htc touche cruise
hi everyone. I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help
parrot5 said:
No display at all? no backlight on the screen? no vibration (signifying it's past a certain point in the loading stage)?
You probably tried taking out the battery for 10 seconds and then putting it back?
As Caid444 asked, tried holding Back+Power for a few seconds (after making sure power is off and not just hanging. Take off battery for 10 sec and reload)? Tried holding Home+Power after making sure power is off?
Click to expand...
Click to collapse
I'd really like to say it DOES something... but it doesn't . I tried Volume down + power, back + power and several more combination always taking out the battery and putting it back.
It's bad... Do u know if there's any hardware service for this?
Just a wild guess, but since the phone sucks more battery, then a vampyre on rampage.
Could it be an idea, to charge the battery before, or have the usb cable pluged in, when you press back+home? (the same buttons you used to enter fastboot)
I'm pretty sure what you're trying to say is, you know enough about the phone to know how to bring it into it's multiple boot options, and none of them make the phone even burp. So there's no need to tell you to press this button plus that button, or insert usb or remove usb, or battery or such, because you've already done all that.
Well, I'd have to agree with you that it's dead. Unfortunately, there's nothing to do at the moment. I'm guessing (or maybe just hoping) that in the future there will be an unbricker for our phone, much like those available for many htc branded winmo phones. In the meantime, how old is your phone? Can you still bring it back?
Caid.
444
p.s To anyone else who's trying to figure this out, let's assume that he's already tried the many variations of recovery procedures and that it's still not working.
argc79 said:
I've got a "Brick" HTC Magic - Vodafone.
Basically, when i press the power button doesn't start. It happened after follow the "Install / Update SPL" ( http://code.google.com/p/android-roms/wiki/SPL ) guide.
Is there any way to recover it? or should i put it on the bin?
Click to expand...
Click to collapse
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade? (I hope you didn't try to flash a G1 SPL on your Magic...).
Amon_RA said:
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade?
(I hope you didn't try to flash a G1 SPL on your Magic...).
Click to expand...
Click to collapse
That's how my brick arrived ! Tried Hard SPL, after installing the one you suggested. Yours okay, Hard SPL no. But even after installing the spl, no fastboot adb.
BRICKED by HARD SPL ( the recommended )
Same here, I have just bricked my new vodafone HTC Magic (Vaffanc...)
downloaded from here: http://code.google.com/p/android-roms/downloads/list?q=label:SPL
I hope something can be done. It is not reacting to power button at all.
Amon_RA said:
If it's really a brick and we all want to learn something from this then we need to know the following :
1. What was your original SPL
2. To which SPL did you "try" to upgrade? (I hope you didn't try to flash a G1 SPL on your Magic...).
Click to expand...
Click to collapse
I think you are right, I have flashed the G1 SPL. But the page is really not clear, it start speaking as Dream/Magic and probably it is only for Dream. Since it says to apply the Hard Spl and in the download link(http://code.google.com/p/android-roms/wiki/SPL) there is no clue that it is not for the G2.
Any idea? anybody got it changed from the shop with no problems? (mine is vodafone in the netherlands)
Me idiot, I have to leave tomorrow for holidays!
byronhero said:
I think you are right, I have flashed the G1 SPL. But the page is really not clear, it start speaking as Dream/Magic and probably it is only for Dream. Since it says to apply the Hard Spl and in the download link(http://code.google.com/p/android-roms/wiki/SPL) there is no clue that it is not for the G2.
Any idea? anybody got it changed from the shop with no problems? (mine is vodafone in the netherlands)
Me idiot, I have to leave tomorrow for holidays!
Click to expand...
Click to collapse
as far as i can see no need to flash spl on vodafone magic. i have the same phone and all i did was root with Rav1.1.1G.img and flashed rom of my choice. you have flashed phone with g1 spl and it actually says g1 on the link you provided..........can't see how you missed it. with phone off press home+power button as that bring up recovery image. Rav image file is safer due to that. i am sure if hardspl was available for Magic it would be posted on here as a sticky
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
thanant said:
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
Click to expand...
Click to collapse
You did brick one with the hardSPL and now you bricked another with the same stuff? Didn't you learn the first time? Only way is to go back to the store and tell em you did it again.
thanant said:
hi
all
i have been recevied new htc magic phone from vodafone on line contract . after i done hardspl my device gone blank not power back on . and change amber light it working .... but i cant power on my device how can i reset device with go gui mode ? i had update hardspl from follwoing link http://code.google.com/p/android-roms/wiki/Install_Hard_SPL . i cant take it vodafone shop becoz just week before same happen so this is my second new phone . please help me if know any other idea
thank you
dana
Click to expand...
Click to collapse
It seems to me you need to go back to basics and start here
A noob question but what exactly does flashing a new SPL unlock.
I got my Vodafone UK HTC magic and simply Downloaded a 32B ROM and used nandroid backup to apply the update.zip and it installed fine and can use Root required apps.
hi all
My HTC magic was bricked after update SPL. Now when press power button, it stuck at HTC magic logo, anyone have solution for fix its?
I Can not understand how can this be possible. Why guys all of you, don't read before trying to change your SPL???? You even don't need any changes about it?! Why do you try to change the SPL? Do you know what that SPL does? I think most of you - don't.
My next question is why all of you are trying to flash the G1 SPL onto Magic phone? Are you crazy or what? There is NO HARDSPL for Magic (G2, Sapphire or whatever you want to call this device)!
The SPL collection is posted in this forum by Amon_Ra, and if someone want to change the SPL can do this by downloading some of the SPL collections posted here.
say2k said:
hi all
My HTC magic was bricked after update SPL. Now when press power button, it stuck at HTC magic logo, anyone have solution for fix its?
Click to expand...
Click to collapse
Power off your phone! Then press and HOLD the "back button", while holding it press once the red one(which you usually use to power on the phone). It will power on (i hope). If you get in fastboot mode then everything will be fine.
I was on Radio 2.10.50; i fashed radio 2.07.50 everithing was fine after the flash; then i run TASK29 by doloop; but after that the bootloader dont start, only the HTC star screen appears, i have to pull out the battery to reset the phone, and restart with the volumne down button pressed but still the same i tried almost 20 times but still the same.....
PLEASE SOMEONE HELP ME.....i flashed almost 40 times before and run TASK 29 before but this never hapened, im desesperated.....
take your battery off, wait 20 seconds. Put battery back in, hold Vol- and push power. ou will be at the 3 color screen. Connect the USB cable, get the 'USB' text below and flash a ROM.
Obviously you have HSPL, on the phone, right? you were able to do task 29..
bigE
Bootloader wont charge
Yes i have HSPL, but after the TASK 29, i think it have been deleted, now the bootloader does not exist, i tried pushind down and reseting the volume down, but without the bootloader, it wont start.
Maybe if i run a SHIPPED ROM from the SD card...???
dannytgt said:
Yes i have HSPL, but after the TASK 29, i think it have been deleted, now the bootloader does not exist, i tried pushind down and reseting the volume down, but without the bootloader, it wont start.
Maybe if i run a SHIPPED ROM from the SD card...???
Click to expand...
Click to collapse
i don't think run Task29 will delete bootloader. You should wait for better advices from someone in here before you try something else that you are not sure.
nope, that is not possible. Unless you have a malfunction with the phone, there shouls be a bottloader..
Do you hold Vol- (keep your finger on) at all times? you should not leave the button until phone wakes up at bootload. The power button can be pushed and be left after about 0.5 a second.
Another wild idea- maybe you battery is dead? try charging it for 15 minutes..
Thanks
Thanks for your advices man, im doing it, but nothing appears to work, im seriously deseperating, i dont know why the bootloader dont start.
Even more, before i run TASK 29, i ve entered bootloader directly pushing down the volume key and everything was fine; but now it seriously appear that the bootloader have been deleted or even i can acces it.
Ive read some other similar cases; and a lot report the same problem, after flashing a new radio, and then runing the TASK29, the bootloader,apparently have been deleted.
About the battery
About the battery, i also think that was the posible problem,because, it was abouth 60% when i flash the radio; and when i run TASK 29, i dont see how much it was,because, ive entered bootloader directly; but ive charged for about 1 hour and still the same the bootloader wont charge, i only get the damn HTC screen.....
I was thinking about flashing shipped rom fom the SD card, but thing it be imposible because to do HSPL (bootloader) is needed, and or my bootloader has deleted or is imposible to acces it so i think that will be a useless option
Posible solution
I think one posible solution was to install HSPL from SD card again; but i think it is imposible...but seriously i wish i was wrong about it.
OK then, try to flash a stock ROM, although i doubt you can.. Maybe you VOL- button isn't really pushed in? I am running out of ideas.. I have HTC phones for several years and never lost the bootloader. By definition the bootloader is a different component on the phone's board, and oe can not write to it from the USB interface (normally it is hardwire write protected). Do you have another battery? or did you try charging a bit?
dannytgt, what model of your device?
I think the answer is simple. When you ran Task 29, did u put the desired Radio in the same map? was it Called ruu_signed.nbu? if you didnt, that would explain why you have no bootrom.
I would run it again but this time with the latest radio in the same map. I hope it works for you man.
GL
TheOne741
BigE said:
OK then, try to flash a stock ROM, although i doubt you can.. Maybe you VOL- button isn't really pushed in? I am running out of ideas.. I have HTC phones for several years and never lost the bootloader. By definition the bootloader is a different component on the phone's board, and oe can not write to it from the USB interface (normally it is hardwire write protected). Do you have another battery? or did you try charging a bit?
Click to expand...
Click to collapse
you're right i cant install stock rom; i tried pushing the volume button every way posible, i ve charged the battery for about 3 hours exactly...still the same..
dannytgt, what model of your device?
Click to expand...
Click to collapse
HTC HD2 Euro Version, i was running Touch X-treme ROM
I think the answer is simple. When you ran Task 29, did u put the desired Radio in the same map? was it Called ruu_signed.nbu? if you didnt, that would explain why you have no bootrom.
I would run it again but this time with the latest radio in the same map. I hope it works for you man.
GL
Click to expand...
Click to collapse
You re right when i run Task 29, i dont have put the Radio in the same folder; i flashed the Radio separately, and then i Run TASK 29.
I tried to run it again. but its imposible, because I DONT HAVE THE BOOTLOADER, so its imposible....
i really apreciate your ideas, i really thanks all of you guys and i hope you will still sharing any ideas about unbricking my phone.
It gets really hard to get a phone like this in my country, i ve done a lot of effort...to have this phone...so i still dont give up about leaving it like that
TheOne741 said:
I think the answer is simple. When you ran Task 29, did u put the desired Radio in the same map? was it Called ruu_signed.nbu? if you didnt, that would explain why you have no bootrom.
I would run it again but this time with the latest radio in the same map. I hope it works for you man.
GL
TheOne741
Click to expand...
Click to collapse
The radio is not needed to start the bootloader.
Well, strange issue with your phone. You really can't enter the bootloader by holding vol down press power on and keep holding vol down?
There MUST be some kind of boot loader. i think without there would be a white screen.
If it is not opening in Boot loader try flashing rom using sync process if your hd2 is booting to Os. otherwise that is only way other have described you. Take battery out . Wait for 5 minutes. Put battery in n press Vol Down button and press power on button. your phone should on in Boot loader .
Some time it happens with me also. but automatically after 2-3 tries it loads in boot loader menu.. dont know what is the problem.. but whatever it is.. IS Strange..
Good Luck
Have you tried hard resetting your phone by holding both the up and down volume when you start? Task 29 deleted the rom so you will need to flash a rom, but if you cant enter bootmode, thats not possible..
Your problem seems to be quite unique. Almost makes me think it is the volume down button that is not responding well...
do you have your battery cover on when trying to press the volume down button?
If yes, try it without the battery cover on
The radio is not needed to start the bootloader.
Click to expand...
Click to collapse
Yes, i have used TASK 29 before, and no need for radio in the same folder;
Well, strange issue with your phone. You really can't enter the bootloader by holding vol down press power on and keep holding vol down?
There MUST be some kind of boot loader. i think without there would be a white screen.
Click to expand...
Click to collapse
I tried for about 100 hundreds time, but nothing happens, so i say before, when i useTASK 29 i've used the bootloader using the volume hardware keys, and it works perfectly
If it is not opening in Boot loader try flashing rom using sync process if your hd2 is booting to Os. otherwise that is only way other have described you. Take battery out . Wait for 5 minutes. Put battery in n press Vol Down button and press power on button. your phone should on in Boot loader .
Some time it happens with me also. but automatically after 2-3 tries it loads in boot loader menu.. dont know what is the problem.. but whatever it is.. IS Strange..
Click to expand...
Click to collapse
I ve tried syncing directly with PC, but it's imposible...totally useless the phone doesnt sync.
This **** never hapened to me before.....i've done a lot of times and the bootloader was always there....
Have you tried hard resetting your phone by holding both the up and down volume when you start? Task 29 deleted the rom so you will need to flash a rom, but if you cant enter bootmode, thats not possible..
Click to expand...
Click to collapse
yes, i've done this also, the power button does not respond; so i pull out the battery and then i put while pressing the vol key down...nothing happens....still no bootloader
do you have your battery cover on when trying to press the volume down button?
If yes, try it without the battery cover on
Click to expand...
Click to collapse
Yes i've also tried this
Your problem seems to be quite unique. Almost makes me think it is the volume down button that is not responding well...
Click to expand...
Click to collapse
Right now im on my girlfriend's house, but by afternoon i will disamble the phone so i'll activate the vol key down directilly, to run out the hardware key malfunction posibility
Thanks again, all of you guys, i ll try every advice you give me
I cant acept that my HD2 is killed.....but the options are finishing.
It's so ****ing rare, even i've scaped from my HD2 get stolen, a few times and now it gets kill by me...
dannytgt said:
I think one posible solution was to install HSPL from SD card again; but i think it is imposible
Click to expand...
Click to collapse
correct, impossible.
The phone wont go past the grey screen because there is no rom to load. Bootloader has NOT been overwritten,. task29 cannot do that.
Chances are you simply aren't entering bootloader correctly.
Take off the battery cover (to get a better press)
phone completely powered off.
press, hold and keep holding 'volume down' (not up and down, not up, just down)
tap AND RELEASE (dont release vol down) the power button
keep holding vol down
as soon as the three coloured screen appears, then release vol down.
once the word serial changes to usb, flash your rom.
i have a feeling your Vol Down button is not working. that's why its not entering bootloader. u going to disassemble your phone? hmm...be careful with that.
Bricked HD2
Would you be willing to ship it to me? I could have some fun trying to figure some stuff out since you're not having any luck.
I flashed my phone and worked great, then flashed the phone to a different ROM Kumar premier and the phone was just shuting off by it self and now the phone is stuck on the page that has "core cell" design, with the red writing in the bottom left corner what do I do. Please help.
reflash
try to reflash the stock rom first to remove the core rom boot screen. after that do a task29 then flash the kumar rom again
OK so I am new at this where do i get a stock ROM and what is a task29?
Ok so Now I cant even connect to the activsync to try and flash it again.
Task29 basically wipes all traces of the ROM/OS (not the radio) off the device. Now it's easy to do, using this .exe by doloop.
(remember, afterwords you will not have an OS on the phone. Just the splash screen you're looking at now)
Here's the thread as well, might want to read that to understand it better.
jsfengine said:
Ok so Now I cant even connect to the activsync to try and flash it again.
Click to expand...
Click to collapse
no need for active sync connection, , from here on, till you fix it, do everything from bootloader. So long as it says 'usb' in bootloader, flashing will work.
OK so I just have never heard of bootloader or just never heard used like that please point in that direction. If you cant do it from activsync then how do you do it if cant connect to the computer.
hold the volume down button while turning on will get you to the bootloader
and the stock rom you're looking for is in the the sub forum list.
OK so I am ready to do this but man I still have no way to connect to my computer to do it. The phone and the computer are not talking without activsync, so I am not sure how to do it without this HELP ME PLEASE.
OK so i messed this up bad a taks29 this thing without a stock rom on it and no it stuck on that damn screen and will not connect to my computer to flash it please help me
can you go into the boot loader? the tricolors screen? when you plug the cable do you see USB at the bottom? if you do then you are connected and ready to flash
jsfengine said:
OK so i messed this up bad a taks29 this thing without a stock rom on it and no it stuck on that damn screen and will not connect to my computer to flash it please help me
Click to expand...
Click to collapse
Everything you are trying to do has been said in this thread..
Task29 will leave you with ONLY the splash screen (and radio) and if you don't go into bootloader when you restart (hold volume down) it will keep going to that screen and your PC won't be able to connect. So restart (power off then power on while holding volume down until tricolor screen)
All makin sense now?
Thank you so much I got it working thanks for all the help
Ok so I am having issues with the phone just shutting off and restarting while i am making phone calls. Do you think that this is the flash or just the phone itself? Do you think that it is the ROM? Thanks
try to reflash the rom
after flashing to 14 jan mdj. my hd2 crashed after 1 day of use. After that I can't boot into android or use USB. I think I even can't charge the phone. I don't see the red led. Andy ideas for fixing it? Try a new battery? It doesn't start up anymore, but it did a few times and said 12.fatal hit when booting android. I haven't tried Tricolour because I can't start it up anymore
Thanks,
When you turn on your phone what happens? What screen dow it take you to? What does it say when trying to run android? .......and for future notice this is the comnplete wrong section for this....and some more info regarding device, hspl, radio would be helpful too.
oh word? ... try this
1..first download the official wm 6.5 rom from tmobile or http://www.htchd2forum.com/general-...SID=799c9ce6abe4e3ddc05368f8432db509#msg22469
2...second remove the SD card and connect the phone to ur computer
3...hold the down volume + power buttom till u see 4 colurs and them run the tmobile official rom... let me know what happens
it doesn't boot up anymore, I will post again when I have it booting again.
All have to do is to download an htc official rom and connect ur Htc hd2 to
computer and flash it
Good luck
Sent from my HTC HD2 using XDA App
phaverkamp said:
it doesn't boot up anymore, I will post again when I have it booting again.
Click to expand...
Click to collapse
connect the phone to ur computer
hold the down volume + power button till u see 4 colors and them run the tmobile official rom... let me know what happens
In the name of the wee man.
Post this in the right bloomin' topic.
The Mods have just spent an age reorganising this whole corner of XDA and what do you do?
Bugger it all up.
Well done.
At least you are consistent, you buggered your phone and the forum. Bravo.
phaverkamp said:
it doesn't boot up anymore, I will post again when I have it booting again.
Click to expand...
Click to collapse
Can you seriously follow anyone's instructions given man? Quit trying to boot the phone. Connect the phone with your PC via the USB cable. Hold down the "volume down" key and the "power" key at the same time. Tell us if you see the tri colored screen.
phaverkamp said:
after flashing to 14 jan mdj. my hd2 crashed after 1 day of use. After that I can't boot into android or use USB. I think I even can't charge the phone. I don't see the red led. Andy ideas for fixing it? Try a new battery? It doesn't start up anymore, but it did a few times and said 12.fatal hit when booting android. I haven't tried Tricolour because I can't start it up anymore
Thanks,
Click to expand...
Click to collapse
Have you checked the battery contacts? They bend very easy, and the symptoms you describe are exactly those of that. If they are bent, VERY, OH SO VERY CAREFULLY straighten them up. If one or more are broken, I hate to tell you this, but you need to buy a new phone.
phaverkamp said:
after flashing to 14 jan mdj. my hd2 crashed after 1 day of use. After that I can't boot into android or use USB. I think I even can't charge the phone. I don't see the red led. Andy ideas for fixing it? Try a new battery? It doesn't start up anymore, but it did a few times and said 12.fatal hit when booting android. I haven't tried Tricolour because I can't start it up anymore
Thanks,
Click to expand...
Click to collapse
I think you have wrongly done the Clock Work Mod which shows the 123Fatal Hit error and ur hd2 remains stuck there. Your HD2 is not crashed at all just charge it with an external charger then go to bootloader by pressing n holding Volume Down key and Power button until you the triple coloured screen, then connect your data cable to HD2 and flash it with a stock windows mobile rom so it will restore ur hd2 and after that u can install nand rom on it by following each and every step mentioned in tutorials here. Whenever I select boot AD SD after flashing partition layout I always get 123Fatal error now I don't understand what the problem is....If someone has a solution for this problem please reply in this thread as I don't want flashing through DFT method.