Related
Dear Bros,
I have a very serious problem here with my 818pro, which noone may have encounter in this forum, let me tell you in sequence:
1)First, after I downgrade my rom with this file Customize_rom_PDAMobiz_Editon_Upgrade_Rom_for_IPLSPL_2.15.0001_v.1.02.rar, I was unable to power up from USB. I can only power up using the wall mains.
2)After powering up from my wall mains, I upgrade my OS using this file
AKU3.3.07.ASERG .
3)After upgrade and hard reset, I am unable to boot up using both the wall mains and even the USB! My display just went blank, and my two leds (orange and blue) keep blinking on and off.
4)I connect my 818pro using USB to PC but cannot go into the bootloader mode nor boot up into the OS.
5)I connect using my wall mains (but not link to PC) and is able to go into bootloader screen, but still unable to boot up into the OS.
Here, I am unable to perform any upgrade/downgrade of ROM using the mains power as I cannot connect to my PC at all!
6)Worst case, I do not have any ROM backup file on my SDcard, therefore am unable to do anything at all!
7)Lastly, can any of you expert brothers here able to advise me wat to do now, or able to provide me with any SDcard rom backup for the 818pro, as I guess that is the only option out for me now???
Would be deeply grateful to the kind brothers here for helping me out! Sorry for the long story which may be confusing.
Best Regards
valiance said:
Dear Bros,
I have a very serious problem here with my 818pro, which noone may have encounter in this forum, let me tell you in sequence:
1)First, after I downgrade my rom with this file Customize_rom_PDAMobiz_Editon_Upgrade_Rom_for_IPLSPL_2.15.0001_v.1.02.rar, I was unable to power up from USB. I can only power up using the wall mains.
2)After powering up from my wall mains, I upgrade my OS using this file
AKU3.3.07.ASERG .
3)After upgrade and hard reset, I am unable to boot up using both the wall mains and even the USB! My display just went blank, and my two leds (orange and blue) keep blinking on and off.
4)I connect my 818pro using USB to PC but cannot go into the bootloader mode nor boot up into the OS.
5)I connect using my wall mains (but not link to PC) and is able to go into bootloader screen, but still unable to boot up into the OS.
Here, I am unable to perform any upgrade/downgrade of ROM using the mains power as I cannot connect to my PC at all!
6)Worst case, I do not have any ROM backup file on my SDcard, therefore am unable to do anything at all!
7)Lastly, can any of you expert brothers here able to advise me wat to do now, or able to provide me with any SDcard rom backup for the 818pro, as I guess that is the only option out for me now???
Would be deeply grateful to the kind brothers here for helping me out! Sorry for the long story which may be confusing.
Best Regards
Click to expand...
Click to collapse
Hey man,you're not alone.. my 818pro do act like that sucks things as yours...
hoping expert's help ,too.....
solved...just replace a new battery...haha..
really? replace a new battery will help? why is that so??? my battery is still good , and the only thing i did to **** up the pda is just reflashing the rom to a wrong one.
what happen when u replace a new battery? can share?
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
hey thanks! i've successfully unbricked my 818pro and flashed it with os 1.013, a very early version, and only that seems to work! I had tried flashing to aku3.3 clean rom from pdamoviz but it stuck at the splash screen after successful flashing.
another funny thing, although i unbricked my 818pro, i can still only soft reset it thru my charger instead of usb. If i soft reset while on usb power, the device will just shut off and show blue and orange flashing leds. Do u have a workaround for this problem?
valiance said:
hey thanks! i've successfully unbricked my 818pro and flashed it with os 1.013, a very early version, and only that seems to work! I had tried flashing to aku3.3 clean rom from pdamoviz but it stuck at the splash screen after successful flashing.
Click to expand...
Click to collapse
hI,How did you flash the rom? You could not go into bootloader mode, nor connect through usb. Please give the procedure used, because I have the same problem. Thanks.
no and there are still a lot of problems for me... I bricked 2 batterys already for example but I'm working on it ... but its a little bit different as I flashed a Wizard bootloader and I have no idea what happened with your phone^^ but something else... I know the problem though, often my phone doesn't even bootup after soft reset if its connected to the charger...
cr0ssy said:
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
Click to expand...
Click to collapse
|I tried the same with my G3 JAMin and it worked. I have a G4 JAMi wth the same problem. I tried the above solution but di'd not succeed. Any ideas?
please need help!
i try to downgrad my "prophet" and now i have (boot loader mode) only with AC adaptator and i see this: "
"get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that"
but my english is not well, can you try to explend me in french or by a graphic please?
I have problem in my HP 6815rw, during update software my handset turned off because of my computer reboot and now it’s like a dead and not able to turn on and only red light appear when charging or usb cable switched is there possible that its loader reload again?? pls help me accordingly
Regards
Mani
Hello all xda's members , It's my first post but I know a lot of things about this forum and about Motorola Defy ...
I've got something very strange , after a long time that I used Miui Rom ..
Suddenly , last week My Defy doesn't snow me if it's charging ( but still charge untill 97% ) and doesn't want to connect via USB . I've tried with 3 cables and nothing work .
Charging problem it's not too big because it's works , but no connect to USB .
And .. this is the strange thing :
I've connected to PC via USB in bootloader ( Power button + up volume ) and it seems to be allright .. BUT !! WITHOUT BATTERY !!! JUST PLUGGED TO USB PC !!! AND DON'T RECOGNIZE RSD LITE ( USB MASS STORAGE OR EVERYTHING !
And it snows that " Battery OK " .. What's wrong with my phone ?!
Please help me , I need a quickly answer Tell me if it's a hardware problems .. That's what I think
Thx all .
is this windows?
i have similar issues... windows doesn't detect my phone neither in mass storage nor bootloader... but USB debug is working... I can do adb...
however in Linux my phone works correctly... and I can also flash using sbf_flash in Linux...
seems to be driver issues for me...
It says MTP device driver not found...
Sent from my MB526 using xda premium
Yes , it's windows , but I replaced drivers and still not work .. I'm not sure if that's software problem .
It's normally if I pull out battery ( connected via USB ) and phone still work ?( without restart ) And if I pull in battery and disconnect from pc still work without restart ? ..
And charging problem : my phone doesn't snow me that it's charging .. only if I go to settings /system / Battery settings ( say it's discharging ) I see how increase energy level ..
What's wrong ? I've got this problem again a long time ago , it was drop from charge a few seconds , and didn't charge .
Maybe can be this problem because I used it underwater a few times . After that , I had lot of water inside , didn't want to charge and connect USB .. after I used a hair dryer and pull out water , everything works fine
Any reason ?!
hey there :good:
can u help me with that please ?
downloaded the drivers for motorola and still the pc not recognized it :crying:
what can i do ? tnx for all the help :highfive:
p.s all the usb in my computer is ok - test it with all usb devices !
the motorola defy runing 2.1
1.jast format the sd card - fail to recognized it
2. replace sd card - fail to recognized it
please help me
tnx.
& installed motorola rsd lite & motorola divice manager - fail to recognized it ...
please i need your help.
in the divice mamnager in windows 7 i cant see a yello triangle on any off the usb [email protected]#?!
but still the pc cant recognized the mobile motorola defy phone !
what can i do ?
If you rejoin yourself and try to be more accurate with your's problem description somebody will help.
First: what do you wanna do?
Second: power off your phone. Power on with Vol+ pressed. Boot menu will appear. Connect the usb cable to PC and after to phone. In what way pc reacted?
pgreed said:
If you rejoin yourself and try to be more accurate with your's problem description somebody will help.
First: what do you wanna do?
Second: power off your phone. Power on with Vol+ pressed. Boot menu will appear. Connect the usb cable to PC and after to phone. In what way pc reacted?
Click to expand...
Click to collapse
1.OK - need to flash to jelly ...
2. did what u say ... -> im geting a black screen bootloader 09.10
battery ok
ok to program transfer mode:
ok
thats it the pc dont - dont do anything ...
what can i do from here mate ?
i truly appreciate your help !
im despaired
please help
tuneon said:
im despaired
please help
Click to expand...
Click to collapse
XP is more suitable for flashing. I am also faced troubles with win7
Sent from my MB525 using Tapatalk 2
tuneon said:
1.OK - need to flash to jelly ...
2. did what u say ... -> im geting a black screen bootloader 09.10
battery ok
ok to program transfer mode:
ok
thats it the pc dont - dont do anything ...
Click to expand...
Click to collapse
From this position if you connect the Defy to PC through usb cable you will see a message on the pc saying that it search the drivers. After pc find and install drivers (or you install drivers from forum) start RSD and do the flsh. If you see nothing most probable that usb cable is defective.
Fail - please help me
tuneon said:
Fail - please help me
Click to expand...
Click to collapse
Dude, I'm having this problem, too...
A friend gave me his Defy to let me repair it - it has the LED Bug (or what its called), so it does nothing. Just giving a white LED, when it has been connected with USB Port... I tried so mich different drivers, USB-Ports and USB-Cables... All Modes that I found I tried and so on, but no chance...
Now I hope to get a important information in this forum...
...sent with my LG Optimus 4X HD...
tuneon said:
Fail - please help me
Click to expand...
Click to collapse
Did you try with another USB cable?
first step
1
Does the phone charge?
charge the battery
2
hold vol+ button, vith the other hand hold power
3
Now you can drop phone on table,
what u see
¿triangle with ! ?
¿white text?
ok, this is the bootloader
4
power off.
SOFTWARE
rds lite, version and drivers ok? sure?
uninstall all(motorola, drivers, rds, all), reboot pc, reinstall
restart after installing each program
(THIS is only to have a clean instalation with appropiate aplications and drivers)
run rds lite and conect phone(with original motorola usb)
(time ago have problems with galaxy ace usb)
*
ok did it + hard reset to the defy + format to the sd card
kienlodiria said:
1
3
Now you can drop phone on table,
what u see
¿triangle with ! ?
¿white text?
ok, this is the bootloader
*
Click to expand...
Click to collapse
??? What method is that?
foramt my laptop to try to get connect 2 the defy - but stiil - fail
help please
tuneon said:
foramt my laptop to try to get connect 2 the defy - but stiil - fail
help please
Click to expand...
Click to collapse
I didn't say to format the pc but to try another usb cable because sometime is a data cable problem.
pgreed said:
I didn't say to format the pc but to try another usb cable because sometime is a data cable problem.
Click to expand...
Click to collapse
did all you say mate but stiil - fail
Now the computer says that the usb is unrequgnized ?
after i install the drivers:
http://www.mediafire.com/?spf3928sdnde4o3 --> what can i do now please ?
tnx.
Hello everyone,
I think I've completely bricked my phone. I had a problem with security boot and after patching wrong "aboot.bin" it doesn't work Currently when i'm trying to turn it on, it only vibrates and nothing else happen. When I plug in the USB and connect it to the PC, phone also vibrates but isn't detected. When i put the battery off and connect the charger or usb it shows screen about not battery plugged.
Please help me and explain how to make it detected again.
nalif20 said:
Hello everyone,
I think I've completely bricked my phone. I had a problem with security boot and after patching wrong "aboot.bin" it doesn't work Currently when i'm trying to turn it on, it only vibrates and nothing else happen. When I plug in the USB and connect it to the PC, phone also vibrates but isn't detected. When i put the battery off and connect the charger or usb it shows screen about not battery plugged.
Please help me and explain how to make it detected again.
Click to expand...
Click to collapse
Unfortunately, there's nothing you can do at this point.. If you are still under warranty, just return the phone, they will probably change its motherboard or just change the phone itself. I have also been in the same situation as you, I tried everything, but nothing worked..
nalif20 said:
Hello everyone,
I think I've completely bricked my phone. I had a problem with security boot and after patching wrong "aboot.bin" it doesn't work Currently when i'm trying to turn it on, it only vibrates and nothing else happen. When I plug in the USB and connect it to the PC, phone also vibrates but isn't detected. When i put the battery off and connect the charger or usb it shows screen about not battery plugged.
Please help me and explain how to make it detected again.
Click to expand...
Click to collapse
Can you get into the download mode? Vol + and then plug a cable into your phone
And i have same problem,but no one dont know how to resolve this...
Are you install corect LG USB drivers ?