Database Users

S200 dead, ROM Update failed

hi
i have a QTEK S200. Today i tried to update my ppc with a WM6 version, but after 40min. the upgrade program crashed down.
After this it was impossible to enter in the main menu of the ppc. the ppc remains hanging on the QTEK screen. I've tried to enter in the bootloader with the color screen, to connect the ppc with my usb cable an the notebook, but my notebook does'nt find my ppc. And now the battery is empty (even connected with the usb cable on a working pc) and i can't switch on my ppc.
Any solutions?

Charge your Batterie and make Hard Reset. Charge VIA Caddy.

done. but the screen remains on the QTEK start page. Bootloader is possible and i get the 3-color screen but my notebook does'nt find my ppc... It's strange because yesterday everything was fine and the connection to my notebook was ok but in the 3-color screen i can't build a usb connection.

ok, problem solved. i've puted a new core on the ppc and now appears the old wm5.

how did you manage to get back to the old rom ? i am stuck on the qtek screnn and the only thing i can access is the USB flash 3 colors screen but my pc doesn't seem to the device...
any help greatly appreciate )
thx in advance
ben

do you have the problem with the SPL 3.08?

no I am in SPL 2.20... and IPL 2.09...
thanks for your help

please write the full ipl/spl number!

here it is :
IPL : 2.09
SPL : 2.20.0000
thx

finaly I manage to dowgrade it by changing my driver - the problem was coming from vista

important is to know, that the 3-color screen give the possibility to communicate with your computer (connected with usb).
so, you have the possibility to copy a new core on it. after that you put a new wm or you take the old one. in my case, the old wm5 was still on the ppc.
yesterday i was testing the wm6 in german but it was not really nice... so i work again with wm5 and wait till a complete wm6 solution is available.

Need urgent help plz...

Hi, I tried to get answer for my problems, but none any specific
so I`m startin a new thread...btw
My JASJAR has the same problem as lots of folks around here like it shuts off at any hard work like starting the camera or charge at 60%. I came to an end that as it works ok with the charger on, then the problem must be on battery. Well I'll try that
But the another problem is PC connectivity...it doesn't recognize the device
I tried MS Active Sync 4.1, 4.2, 4.5, windows 2000 SP4, xp SP2, different computer...just no luck, in bootloader mode it shows "serial" and "0.60" and whenever I plug in the USB, it shows USB, and then same, device not recognized...what to do?
And when I start the device, on blue background imate logo..it shows Radio 0.00.00, what does it mean..I can't even upgrade it as USB is not recognized...waiting for flash from SD, but no luck. Can any one sort these things out

First problem, almost definitively the battery.
Second and third problems could even be correlated, first the third problem/doubt, even if I'm not a complete expert, this means that your device was "unlocked" with the aid of a specific program that does just that (if you're interested in knowind how, go to the uni's wiki and read about unlocking), the Radio version 0.00.00 is just a "by-product" of that process.
So, if you're asking about this, you didn't do this by yourself, so you don't know what and how much has been done to your PDA, then for your second problem, first try a soft reset (this is always windows, remember it!), the re-connect the device (to the PC) and see what happens, then verify that you have the active sync program installed properly (and running) in your PDA, just when you connect the PDA to the computer, the active sync should become available as a running program, so, connect the PDA to the computer, the PDA turns on and says connecting, even if it does not connect to the computer you should see active sync running in your PDA, go to settings, system, memory, running programs and verify that it's there.
Another cause could be hardware (on your PDA), this means, cables and port or even internal (but this is quite unlikely).
Perform these tests and see what happens, then we'll see what else can be done.

Thnz, I trued several soft reset even hard reset,
I tried connecting to the computer with ActiveSync on, with some other software which changes the active sync connection to something like USB serial (from RNDIS ...), even advance networking off, taking out the SIM and memory card...running the device search..no luck.
and btw in computer after installing active sync it gives a window with all menu disabled except "File>Connection Setting". I tried by using bluetooth connectivity. No luck.
I read the thread about unlocking..and tried to do the rest..I mean the second step of unlocking, it showed device successfully unlocked..but all the same.
Any help....

mamaich method
Try this,
Step by Step :
get the tools at attachment , as mamaich told, you have to use it in bootloader mode , (Power + Light Bulb + Reset)
1. Stop Activesync USB connection
2. Uni : Reboot Bootloader then Connect USB
3. PC : Run mtty1.42.exe
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5. type : task 28 55aa
6. Press Enter
7. Cause DOC reformatted, so there's no rom in DOC ,try reflash any rom that you like .
For task 28 55aa in mtty success , will show the message (attachment )
DONE .

Unable to update ROM on HTC TouchHD

Hi all,
I have an HTC Touch HD (1.56). It was tied to Orange Poland, but I have SIM unlocked it with a web service. Now I wanted to try some different ROM (my main language is italian, but english would be fine as well -> as of now I've only been able to partially set language to italian changing registry code, but most of WM6.1 is still in polish). I have tried the HSPLWrapper_Blackstone_156OliNex.exe with no success.
If I just plug the HTC to PC USB cable, ActiveSync wakes up and connects.
I can browse inside, move files, install apps.
When I start the wrapper this is what happens:
1) with advanced USB settings ON (on HTC) the tricolour screen does NOT appear and the wrapper says Connection Error [202]. ActiveSync is ON and ready. -> if I start SSPL-Manual-TouchHD on HTC, the tricolour screen appears, the USB text appears, and on both wrapper and HTC I can see the progress bar at 0%. After a minute or so, the wrapper says there was a problem and shows the recovery procedure (I was never locked on tricolour screen, I just had to remove battery and everything was back to normal). If I try again the wrapper while the tricolour/USB screen is still there, nothing happens, and I get connection error.
2) with advanced USB settings OFF (on HTC) the tricolour screen DOES appear automatically when I start the wrapper, but no matter how fast I am pressing YES on HTC, the USB connection gets killed and ActiveSync disappears.
I have tried 2 different USB cables on different ports (no hub), rebooted PC several times. I have read the 3 wiki pages (HTC_Blackstone_Flash) and the OliNex procedure. What can I do? Can somebody please help me?
EDIT: I am trying this from Windows XP Pro up to par with WinUpdate (.NET 3.5 and everything else is there)
Thanks

You can always try USPL.
But first make sure you follow this exactly:
http://forum.xda-developers.com/showthread.php?t=505377
Hope it helps

A thread already exists for flashing difficulties. Please post your query within this thread
Ta
Rick

RESTORE BOOTLOADER ON Rover G5, Orsio n725, O2 Atom, O2 Atom Exec, HP6815 - Tested

*this is a copy, it is not my work at all* just thought it would be helpful as it helped me restore my bootloader.
Your device is bricked, if and only if, your device won't start normally... even if you press soft-reset, hard-reset, or even bootloader mode buttons. Usually a brick is caused by improper ROM upgrade, and using tools that modify the ROM. Before panicking, do the following:
Brick Test:
Make sure your device has ample battery charge. If you're not sure plug it in with the wall charger for at least 10min
Remove your battery for at least 1 minute
Replace your battery while observing the LED lights
If the LED blinks once upon battery insertion, you might have hope yet
The only way to upgrade on a semi-brick device, is to upgrade through bootloader mode. No bootloader mode, No upgrade possible - period.
Entering Bootloader Mode on Semi-Brick Atom:
Remove battery for for at least 1 minute
Press CAMERA+RESET(stylus) simultaneously
Insert battery while still holding the buttons
Release the buttons at the same time (You should see bootloader screen)
Note: Failure to hold the buttons at the same time during battery insertion will cause it not to work
Manual to restore dead BootLoader (http://wiki.xda-developers.com/index.php?pagename=BootLoader) Rover G5, Orsio n725, O2 Atom, O2 Atom Exec, HP6815 - Tested . (may be 68xx series)
© Copyright to Alex_Beda & 1stMASTER
PDA-HACK.NET Team http://wiki.xda-developers.com/themes/default/images/http.pnghttp://pda-hack.net (http://pda-hack.net/)
If our article has helped you, you can donate the Web Money
WMID 378286389551
for WMZ: Z396747110007
for WME: E114645323227
for WMR: R351032339900
Thanks to all who helped.
Thanks to Winterice for the technical assistance and moral support.
Thanks to ant 125 for useful information
Thanks to Allbest, deniska.75, Borozavr, Erke for moral support.
Symptoms:
The device is not switching on, not entering bootloader.
(most often after the firmware from a memory card)
React to connect charger.
if the battery insert and connect charger, it orage led must be lit .
if the battery remove and connect charger, it orange led must be flashing.
There is only one way for restore bootloader.
Reflashing flash memory in the PXA272 using JTAG.
This procedure consists of two parts.
Hardware (making cable for reflashing) and software (reflashing).
Hardware part:
This pinouts JTAG of Atom Exec, Rover G5, Orsio n725, O2 Atom, O2 Atom Exec
At O2 Atom (not Exec) is the only internal contacts. Located near the Camera button.
http://i218.photobucket.com/albums/cc23/alex_beda/JTAGroverorsio.jpg
There are contacts inside the device, near the buttons CAMERA,
for access them, you need to open device.
There are contacts from the outside, near the SIM connector.
All contacts is working
For inside contacts need this connector
http://i218.photobucket.com/albums/cc23/alex_beda/raz012.jpg
You can so using connector from floppy drive 5.25”. (autor vic180)
http://i218.photobucket.com/albums/cc23/alex_beda/PICT0267-.jpg
http://i218.photobucket.com/albums/cc23/alex_beda/PICT0262-.jpg
LPT connector for PC
http://i218.photobucket.com/albums/cc23/alex_beda/LPT1.jpg
Cable length of a 35-40 sm
This connector for outside contacts
Result connector from connector for floppy drive 5.25"
http://i218.photobucket.com/albums/cc23/alex_beda/raz1.jpg
http://i218.photobucket.com/albums/cc23/alex_beda/raz3.jpg
http://i218.photobucket.com/albums/cc23/alex_beda/vid2.jpg
.
for fixation connector need make this
Or other
http://i218.photobucket.com/albums/cc23/alex_beda/kreplenie.jpg
http://i218.photobucket.com/albums/cc23/alex_beda/vidkrepl.jpg
http://i218.photobucket.com/albums/cc23/alex_beda/vidobsh.jpg
Software part.
http://wiki.xda-developers.com/them...a-developers.com/uploads/RepairBootLoader.zip (http://wiki.xda-developers.com/uploads/RepairBootLoader.zip)
In attached file is the programm JFlashmm,
in the same directory BOOTLOADER from ÀÒÎÌ ÅÕÅÑ (ebo_a.nb0)
from First Firmware,
and driver the giveio needed for working cable.
If you have O2 Atom (not ÅÕÅÑ), it must be in the folder jflash_mm
Deleted file ebo_a.nb0, copyng the fileeboot.nb0 from O2 Atom firmware in the jflash_mm folder
and renaming this file in ebo_a.nb0.
Before connecting LPT connector , you want to press and hold
micro button near to the sim connector.
http://i218.photobucket.com/albums/cc23/alex_beda/knopka.jpg
For example: sticker on the button.
Ground from LPT connector, connecting on ground the device
(using the crocodile connector)
http://i218.photobucket.com/albums/cc23/alex_beda/ground.jpg
Connect cable to LPT port of PC.
Connect charge to the device
Orange LED is blinking.
If LED not blinking,
Check pressed the micro button.
check fixation the button.
Installing the driver giveio from attached file.
Now you can restore BootLoader (http://wiki.xda-developers.com/index.php?pagename=BootLoader).
BootLoader (http://wiki.xda-developers.com/index.php?pagename=BootLoader) needs to be restored in two places.
Need boot flashing to adress 0 and address 3f400.
In folder jflash_mm there is a file start.bat.
Inside this file:
jflashmm pxa27x32 ebo_a.nb0 P 0 PAR
jflashmm pxa27x32 ebo_a.nb0 P 3F40000 PAR
So file ebo_a.nb0 (boot from àòîì exec) will be flashing in two places,
To adress 0 and adress 3f40000, data send to parallel port.
Execute start.bat, if all right , you correct making cable,
it must detect processor.
If message screen on "file *.DAT not find", press Soft Reset.
the program will ask you «bla-bla-bla» Y/N? Press Y
JFLASH Version 5.01.007
COPYRIGHT (C) 2000 - 2003 Intel Corporation
PLATFORM SELECTION Processor= PXA27x
Development System= Mainstone
Data Version= 1.00.002
PXA27x revision ??
Found flash type: 28F256L18B
Unlocking block at address 0
Erasing block at address 0
Unlocking block at address 10000
Erasing block at address 10000
Unlocking block at address 20000
Erasing block at address 20000
Unlocking block at address 30000
Erasing block at address 30000
Unlocking block at address 40000
Erasing block at address 40000
Starting programming
Using BUFFER programming mode...
Writing flash at hex address 3fe80, 99.85% done
Programming done
Starting Verify
Verifying flash at hex address 3ff68, 99.94% done
Verification successful!
So too for the second time in firmware to address 3f4000
You can disconnect charger and cable.
Enter bootloader :
Press Camera button, insert battery and press Soft Reset.
If everything was done correctly, it bootloader is running!!!
Now, as usual (almost)
Connect the device to PC.
Run update firmware for you device.
Must go update firmware.
If all right, it .......
Operation system update, bootloader update,
Running update ExtROM (http://wiki.xda-developers.com/index.php?pagename=ExtROM), but, it should freezes at 6 %!!!!
Disconnect usb cable from device, Enter Hard Reset!!!
Device must switch on, calibrating touch screen etc.
Run again update firmware for you device

I bricked my Xda Atom Pure which i bought second-hand yesterday by trying to hard reset it to clear the memory.
It got stuck at bootloader screen while folowing the above procedure and my pc would not recognise it. I choose option 1; Module debugging mode, pls where do i go from here? its too late to loose this phone. pls help!!!

plz help!!!
Plz help me i My o2 atom dead cannot enter in Bootloader too...plz help!!!

video
can u send a video how to do all thiss or tell step by step plz
i have the same problem can not enter to boatloder mode(tried everything)
i m frm india here we didnt have o2 atom exec. customer care.
plz need help???????/

this methode can be applied on htc magician???
this methode, can be applied on htc magician??? the bootloader is the same?

There is a procedure for Trinity device ?
There is a similar procedure for recover crash bootloader on trinity device ?
When i enter on Bootloader mode (Power+Camera+Reset-stylus) only led blue blink on my test trinity device.
Thanks in advance for your help.

need help
pls,,,my atom is dead, coz when i upgrade is fail,,,show pls the vidio,,,so i can try at my atom

me too
cant bootloader,i try any way but cant..............

Hi All, I am trying restore dead bootloader on my 02 Atom.
have followed all the hardware set up instructions but I can only get to the point of the blinking LED with no response from the software.
Maybe I have misunderstood the English in the instructions. Would really appreciate if some good soul could give me a better translation.
Look forward to a response, many thanks in advance.

psophan said:
cant bootloader,i try any way but cant..............
Click to expand...
Click to collapse
What no lettering on the screen like -->>> V1.0, USB, or SERIAL ..? if you still look like that , it means your device is saved !!!! I also never experienced anything like that and my O2 can live up to this moment ...!!

thank friend
Hakim Rahman said:
What no lettering on the screen like -->>> V1.0, USB, or SERIAL ..? if you still look like that , it means your device is saved !!!! I also never experienced anything like that and my O2 can live up to this moment ...!!
Click to expand...
Click to collapse
But im sucess already

you're welcome
psophan said:
But im sucess already
Click to expand...
Click to collapse
justify still be saved !

this tutor only for PC Desktop user ha?
Possible make JTAG VIA USB? can u tell me how to?

O2 XDA II update error

Hi, sorry, my english is very bad... So I update my pocket PC witch "Xda_II_172181_Final" of forum.xda-developers.com/showthread.php?t=229259 . And now it's dead because obviously lost connection with PC. My PDA shows Serial at the top and v 1.01 below. When I put it in the cradle, it displays usb at the top and v 1.01 below. I keep trying the reccord button, power, and hard reset but it nothing happen Plyzz help me.

Serius said:
Hi, sorry, my english is very bad... So I update my pocket PC witch "Xda_II_172181_Final" of forum.xda-developers.com/showthread.php?t=229259 . And now it's dead because obviously lost connection with PC. My PDA shows Serial at the top and v 1.01 below. When I put it in the cradle, it displays usb at the top and v 1.01 below. I keep trying the reccord button, power, and hard reset but it nothing happen Plyzz help me.
Click to expand...
Click to collapse
Don't be panic man just follow the below steps and your device working like charm
It is actually the disconnection error
1 - first fully charged battery.
2 - install mobile device center or active sync ( as per your OS )
3 - Enter in to the bootloader mode
4 - connect USB cable with ppc device.
5 - wait for detection of the device
6 - drivers are automatically installed if you are using windows7 it shows
driver installed successfully & device is ready to use.
7 - extract the rom update utility from the posts whichever you like ( remember choose it carefully as per your device )
8 - just double click on upgrade icon in extracted folder and yeah you done.
if still any problem persists then fell free to contact me on [email protected]