Hello all,
Let me first preface this with a little story. I currently have a Merlot and a Black MT3G for wify. On my Merlot with still perfect spl and cyan recovery I am running MghtyMax 1.9.1 rom and it works great. She decided to use it on black one that is rooted same but running RA 1.2.2 recovery and rooted ra rom so figure no problem and having issues I can't get either MghtyMax or cyano 4.2.1 to boot on it just hangs on MT3G screen never getting to android/htc over 15 mins just hangs.
I took the mem card (16gb sandisk) 15.4 gb for fat32, 500 mb ext4, 128 mb linux swap fresh partitions. Installed mghtymax and was running good. When I power cycled the phone turning back on froze on MT3G screen. I tried to whipe it, pull battery whipe and flash again. Same result powered up and on reboot wouldn't power up again stuck on mt3g screen.
Figured maybe recover img so I flashed cyan 1.4 recovery what I have on mines, whiped, repartioned, battery pull whiped and installed. Still stuck on mt3g.
Maybe since is still "perfect" spl tried the 1.33.2005 engineering spl and reapeated above steps and no go.
Ok maybe I missed something. Flash back to stock with sappimg.nbh, used 1 click method to put on cyan 1.4, put on eng spl again, whiped, repartioned, push rom battery pull, whipe install still stuck. Ok maybe the rom on that phone different for what ever reason. Tried to whipe and install ADP base then Cyan 4.2.1 (which also works on my device) same issue. Never has a problem getting to either fastboot or recover console though. ended up putting back stock for now.
Any ideas on what I may be doing wrong? Same exact roms and setup that works on my merlot one don't work on a black one. Any help on this would be greatly appreciated as I am completely stumped by this.
I think i figured it out if anyone else has the problem. These are the stps I did to fix the problem.
Flashed back stock with nbh
recovery flasher to put on cyan 1.4
flashed eng spl (not needed)
whiped and battery pull
whiped and installed adp base from cyano thread LET IT BOOT to sign in.
installed cyano let it boot again
whipe battery pull
whipe install hero boot and good
I was having bluries so I had to do bluries fix but up and running
Related
I have flashed the new CyanogenMod and the Cyanogen Recovery 1.4 and when I wipe everything and flash, it'll load up and I can use the phone 100% perfectly, but once I reboot my phone, or turn it off and on, it never goes past the green boot screen. Anyone have any solutions/reasons why it does that? It's with every single Cyanogen mod too, i've tried several of them.
Probably because you have a lot of apps?
If not, reflash it.
tmc_adio07 said:
I have flashed the new CyanogenMod and the Cyanogen Recovery 1.4 and when I wipe everything and flash, it'll load up and I can use the phone 100% perfectly, but once I reboot my phone, or turn it off and on, it never goes past the green boot screen. Anyone have any solutions/reasons why it does that? It's with every single Cyanogen mod too, i've tried several of them.
Click to expand...
Click to collapse
what do you actually flash and what is the actual process, you shouldnt have any issues after it boots up the first time, wipe everything and make an exterior partition meaning get rid of your cyanogen recovery 1.4 and get amon ra's latest... look in the dev section and read up on cyan's page on how to flash the rom
mt3g said:
what do you actually flash and what is the actual process, you shouldnt have any issues after it boots up the first time, wipe everything and make an exterior partition meaning get rid of your cyanogen recovery 1.4 and get amon ra's latest... look in the dev section and read up on cyan's page on how to flash the rom
Click to expand...
Click to collapse
Thanks for help man, right now I'm running dwang's rom 100% perfect w/ no issues at all. it can reboot and everything just fine. I'm just a little worried on going back and trying to flash cyanogens.
When I installed it, I first did the root process, downloading the .apk file and going through all that part smooth, then I downloaded and flashed the Cyanogen Recovery 1.4, and from there I downloaded the two files (DRC83_base and the latest cyan's rom, i forgot the version #) and applied update from SD, first doing DRC83 and right after doing the rom itself, without rebooting the phone. It loads up A-OK and I can installl the apps and go about my business, but once I need to restart my phone, it just never turns back on. I'm puzzled completely...I even did the whole unroot and reroot thing and STILL i'm not having any luck.
K I got confused in there some where did you flash a cyan rom at all in there I read that you flashed the drc83 zip file but sounds like you just flashed that and booted the phone lol... never tried that but.... any way it seems like you are doing everything correct onlything I could suggest is make sure you have the correct htc base image, and make sure you wipe and repair everything!!!!! and also try a differant download of cyanogen as you might have gotten a bad one or something I have never had any issues with a cyanogen rom except maybe a FC back on 4.0xx or something
兄弟，估计你刷成砖了。同情ing。。
This was the g1 I succesfully flashed a rom to and was doing ok (but slow) until I put a sdcard and sim chip in to flash the latest Hero rom to.
In this order this is what happened.
Tmo G1 screen came on
went to black screen and "hung"there
Pull and replaced the Battery a few times to no advail.
Rebooted into recovery mode and hit alt+w
to wipe (was successful) and then hit back+home to reboot
Now it just keeps replaying the hero boot animation over and over.
Any Suggestions?
Thanx in Advance
wipe ext partition.
Do you even have these? You should
1.Haykuro SPL not HARD
2.EXT 3/4 issues w/ 2
3.Amon_RA 1.5.X the cyan 1.4 doesnt have the new feats of amon
Thanx for the replies.
I forget the name of the recovery image I have. But the hero rom I had flashed was a JaHero(Thats what it said on the home screen)which was a very early hero rom and what ever recovery image was around at the time.
So you have cyan 1.4
wipe, wipe then wipe again
I experienced the same. Wipe everything including the D cache. Then re-flash the ROM. I'm using SenseHERO-v1.4 Theme version. There no better Hero for the G1, right now. It doesn't use apps2sd. As a result, snappier less lag. Also, I have greater success with Amon RA 1.5.1. Actually based on Cyanogen's 1.4 with more features added.
Regards, davidrol
You said earlier that you wipe. Never wipe when you're using a hero ROM, you have to wipe then reflash, otherwise it will boot loop.
I tried to use SuperOneClick to root my phone and it seemed to work. The program came back saying I successfully rooted my phone.
I then went to ClockworkMod to install cyanogen and clicked on the appropriate boxes to begin the download process for cyanogen 6.0 stable mod and ran it.
My phone rebooted and started to run some scripts.
Now, the phone just reboots to the green mytouch screen and continues to loop like that and I have no idea what to do.
I can get into fastboot on the mt3g and when I do, my pc makes the sound that states that the phone is connected but when I try to get into the mytouch, using adb, my pc cant access it but when I plug up my G2, I can see the serial number and such showing that it is connected.
I tried to follow the fastboot driver installation page but it didn't seem to work.
Bottom line is I would really enjoy a functional MT3G in either the regular form or cyanogen (which is why im in this predicament now )
For the the record,
I was running 1.6 but got the OTA update for 2.2 before I ended up blowing up my phone.
Thanks for reading this and any aid would be greatly appreciated.
UPDATED:
I found something called SAPPIMG.NBH that allowed me load Android 1.5 onto my phone. I now am back to a functioning device but still, I am super stuck on trying to get cyanogen onto my device. Any helpful hints? From what you read above, did I miss something?
Thanks again.
... Sadness... I have been bashing my face against this mt3g and haven't been able to get cyanogenmod on this phone for the life of me. I have tried all of the builds from 5.08 up to RC1 of 6.10 and I just get the infinite loop at the cyanogen boot up screen. I even tried to flash 2.23.XXXX radio to see if it gets past the boot loop and it does not. Anybody have any insights into my issue?
Thanks,
You must go into recovery mode(boot up by holding down home + power). That will get you to Clockworkmod recovery(I am assuming since you said you downloaded using Clockwork app). From there you need to wipe cache, and anything else you can wipe. Then try installing Cyanogenmod after that. Without wiping the there is not enough space to install and it causes a bootloop.
I'm in the same boat, I'm stuck in a boot loop and I cannot get any ROM to fully load in. I'm using clockwork recovery Radio 2.22 32B.
I tried wiping everything but that still doesnt seem to work. I noticed when I try wiping Davlik cache I dont see any message on the bottom. I thought it would normally give me some sort of message stating that it is wiping davlik or something so maybe it isnt actually wiping it?
Is there some other way to make sure davlik is wiped? Or something else I can do. I just want the phone to boot up at this point. I can get into recovery but thats it.
I know I shouldve done a backup but dumb me was such in a rush I completely forgot, I know im a idiot...
Het I found that same .img file and also reverted back to 1.5 then just went up to 2.2 not sure what was wrong but Rom I put on just went into a boot loop. Maybe it was clockwork recovery.
Sent from my ADR6300 using XDA App
the padawan becomes the master... Sort of...
The problem is that you cannot go directly to 2.2 from 1.5. You have to do the incremental upgrades that take you from 1.5 to 1.6 then 1.6 to 2.2
I'm rooted, unrevoked; I'm currently stuck in a boot loop. I can not reach recovery. I can not get to my rom. I can only access bootloader.
So far I have taken these steps to cure my problem:
Ran RUU software in Windows (with and without sd card in evo)
Flashed RUU as PC36IMG in bootloader
Cleared Storage using fastboot in command prompt
Cleared Recovery and then Flashed Amon Ra's Recovery and Clockwork using fastboot in command prompt
Flashed Amon Ra's Recovery and Clockwork as PC36IMG in hboot
Flashed Sprint Lover's as PC36IMG in hboot
Flashed eng-PC36IMG from Toastctfh's Old Root Tutorial as PC36IMG in hboot
Each of these methods flashed successfully as far as I can tell... yet I still go into an infinite boot loop.
Before the bootloop this is what I was doing:
I had the initial CM7 nightly installed for about 2 weeks. It was buggy, and a few days ago restarted and deleted all my texts, and desynced from google. On rebooting, google apps acted as if I had never ran the phone before - it asked me to enter google account info, etc, upon reboot.
I decided CM7 was too unstable and so I wiped data and davlik, and flashed CM6. When CM6 booted google apps was already on, before I had even flashed it! Anyways I figured I wanted to give MIUI a run, so I wiped data and davlik, and flashed MIUI. It ran fine for about two hours, and then rebooted out of nowhere... and never came out of the boot loop.
I'm really starting to sweat this as I have gone three days now without a phone. Does anyone have any ideas that may help me? Thanks.
If I am unable to get out of my boot loop, does anyone know if I would be able to unroot my phone and then take it into Sprint and get another?
Are you able to boot into recovery?
Sent from my PC36100 using XDA App
unfortunately, nope
Hmm then I'm not to sure what to tell you. That was my only idea.
Sent from my PC36100 using XDA App
bump, maybe with a new day a new person will have a new idea?
Hopefully
Sent from my PC36100 using XDA App
bump to this as I am also experiencing this same situation. Phone stuck in an infinite bootloop to the white htc screen then all over again. can get into bootloader but not into recovery.
tried all the above. this was out of nowhere.
This problem is all over the Evo section, especially in Q&A and I don't think I've seen anyone come out of it.
On the positive side, I also don't think I've seen anyone take theirs back to Sprint and have a tech even check to see if their phone was rooted or not, and btw, next time you flash a new ROM, not saying this is the cause, wipe EVERYTHING, not just cache and dalvik-cache
Having the same problem here also...
didi you try the clear storage mode in the boot loader cause if you already flashed the PC36IMGyou wouldnt have a custom recovery just the triangle screen i recomend doing it with the original 2.1 zip file then just re rooting it put the rom then flash radio and g apps
dominirican said:
didi you try the clear storage mode in the boot loader cause if you already flashed the PC36IMGyou wouldnt have a custom recovery just the triangle screen i recomend doing it with the original 2.1 zip file then just re rooting it put the rom then flash radio and g apps
Click to expand...
Click to collapse
I have tried everything you have mentioned and nothing works...
The OP's list of attempted fixes looks like he ran the gamut.
Unless there's a fix that I haven't read about, it's time for a trip to the Sprint store....
I have someone working on mine that claims he can get it fixed...has access to things I don't. We will see. I will report the results.
Ok...He did it and its up and running. I was trying to flash mine to Boost Mobile so thats how i got mine into a boot loop but he got mine out of it with this...Download the
README_EVO.docx
http://forum.xda-developers.com/showthread.php?t=805612&page=4
Nook color running Racks triple boot via micro SD card. Micro SD card is a Sandisk 8GB class 4 card.
Was previously running fine for many months with the 2/2/12 roms. I would run CM7 99% of the time and I would get a random reboot here and there, but otherwise very stable.
A couple days ago, I had a random crash and tried to reboot CM7. I could get passed the boot loader screen, but then would have a continuous boot loop with the blue android symbol.
Thinking something was corrupted with the rom, I booted to recovery and tried flashed the rom along with gapps. Still boot looping.
I booted to CM9, and was able to run. So I downloaded the latest CM7 and CM9 roms for Racks triple boot. Flashed both along with the gapps and CM9 fix. Apparently I got lucky and was able to boot into CM7.... once. Thinking everything was OK, I went on with my life and ran the new CM7 happily.
Now, a few days later, I've tried to reboot and I'm back at the same boot loop with the arrow spiraling around the a blue skateboarding android. Note, in that short time that I was running the newest Racks triple boot CM7 rom, I did not run a backup, so, I'm basically out of luck with recovery via CWM.
I've flashed the 2/2/12 rom as well as the latest rom to see if either would work again. nothing... still boot looping... for hours now.
Any suggestions other than wiping the SD clean and starting with a fresh install?
Thanks all.
~mike
Bump...
Been a bit, no responses yet. Anyone have any ideas?
Thanks,
~mike
I think the fresh install will help since you already tried partial reinstalling the roms.
Produced by NookColor at ICS AOKP 4.0.4
Nook Color stuck in load screen
I have a nook with CM7 installed on it. was going return my nook to stock to give it to my little sister, but when i went to install the stock stuff back on it got stuck in a loop. It won't boot from an uSD card with clockwork on it and when I tried the 7 hard boot in a row trick, it didn't do anything. Did i really brick the thing? or can it be recovered?
doodlebug81 said:
I have a nook with CM7 installed on it. was going return my nook to stock to give it to my little sister, but when i went to install the stock stuff back on it got stuck in a loop. It won't boot from an uSD card with clockwork on it and when I tried the 7 hard boot in a row trick, it didn't do anything. Did i really brick the thing? or can it be recovered?
Click to expand...
Click to collapse
You are in a recovery bootloop with no recovery installed. Go to my tips thread linked in my signature. Read item A8. You need to make and use my special bootable CWM SD (select the 'larger' image). Then if you want to return to stock, read item A15.