Related
Hi all, i have developed this weird problem in my jasjar and i'm sure it's some settings that need to be changed somewhere and not the battery itself. When i first got the jasjar, it gave me a good 48 hours battery backup on standard use but i lost my charger and started using usb to charge it. it's since then that my jasjar drains the battery in less than 12 hours. i have tried replacing 3 batteries but to no better effect. I remember reading something about the Li ion polymer batteries having the memory effect or something and how to reset that in the bootloader mode. if you guys could help me figure it out and fix the problem, i'd appreciate it! here's the details of my rom.
R:1.13.00
G:42.47.p8
D 2.01.06 wwe
the rom is the wm6 from jwright.
(nb: i had the same problem with my shipped wm5 rom and i thought upgrading it would help but it didnt apparently).
How long do i need to use the battery to check the drain thingy. the reseller tells me to use it for 2 weeks before judging it. i'm screwed with having no battery life to this otherwise beauty of a device! if i could get any help, it would be much appreciated. thanks in advance. (josh).
Had the same problem, been happening all week, the phone would just switch of even though it registered over 80% charge. no i am happy again because i read on the forum that you need to totally discharge the battery occationally for it to get to a full charge, it appears that there is some sort of memory effect where the battery thinks it is nearly discharged, try it, i am sure you will find that it workes.
Had the same problem, been happening all week, the phone would just switch of even though it registered over 80% charge. now i am happy again because i read on the forum that you need to totally discharge the battery occationally for it to get to a full charge, it appears that there is some sort of memory effect where the battery thinks it is nearly discharged, try it, i am sure you will find that it works.
awright...i'd try it. thanks for ur help.
mayer said:
Had the same problem, been happening all week, the phone would just switch of even though it registered over 80% charge. now i am happy again because i read on the forum that you need to totally discharge the battery occationally for it to get to a full charge, it appears that there is some sort of memory effect where the battery thinks it is nearly discharged, try it, i am sure you will find that it works.
Click to expand...
Click to collapse
thanks..
I too has a similar problem but this method did not solved my prob as my jasjar switches off by itself at 40%.
I had a similar problem a couple of weeks ago as a charge would last less than 24 hours when I used to be able to last 2-3 days.
Soon sorted it when I found that the Jasjar had decided to disable the automatic switch off, now a charge is back to lasting 2-3 days.
Mike
Had my MDA PRO for 1.5 years, and never had this problem. Battery lasted for 2-4 days on average, although now I have a 3200mAH battery it lasts for well over a week on a single charge
Lithium ION and Lithium ION Polymer (the HTC Universal uses the latter) do not suffer from any "memory effect". The only battery type that does to any significant extent is Nickel Cadmium, which is rarely used these days.
It's also impossible (well, almost) to completely discharge Lithium ION Polymer batteries - internal circuitry in the battery shuts down the cells when the charge gets too low, at up to 10% charge. This is because a completely discharged L.I.P. battery becomes unstable, broken (unable to be recharged), and runs the risk of explosion or leaking in this state. So don't attempt to drain those batteries completely dry folks - it's dangerous! Letting them run down naturally in your Universal should be safe though because of the cut-out mentioned above.
Maybe the Uni just has a large batch of bad batteries? You should also check what apps you have running on it all the time, and how often you use bluetooth and wi-fi - these two REALLY drain the battery if you keep them on all the time... Also try MemMaid, this is great at cleaning up your notifications queue, which is where lots of apps leave old and obsolete entries clogging it up.
I have the same problem. I do not know where the charger is, so I am always using the USB while syncing. I also tried 2 batteries, but they both last about 12 - 14 hours. Maybe it is caused by WM6.
I did not quite get this solution:
"Soon sorted it when I found that the Jasjar had decided to disable the automatic switch off, now a charge is back to lasting 2-3 days.
Mike"
What is the solution?
2 421....:
sorry for lang. the above understands(i hope)
nastavenia(settings)/napajeni(power)/rozsireni(advanced) tam zaskrtnes co xces a nastavis casy. ak pouzivas phonealarm musis aj tam. pozri si aj podsvirtenie(backlight).
btw aj had the same prob. appeared after 6mnth. i bought new battery. btw here is several threads with same prob. try 2 look for solutions there(imho its only one-new batt.)
I feel like I'm walking on eggs...I bought my Jasjar used on eBay just over a year ago, still the original battery. I almost never use the 110v charger, always a USB conection with my Mac, often recharging at 55-75%. I just intentionally ran down my battery to 18% (got warnings to recharge), and recharge via USB/Mac again. It took me almost 4 days to get to 18%, and Bluetooth is constantly on for ready use with my earpiece.
Curious: are the problems with original or replacement batteries? Cheers,
Update to Radio 115 or 114
It's worth taking into consideration that when flashing, you really need to have a full battery. There are reports of batteries starting this kind of behaviour after user has flashed with drained battery, then causes battery charge issues until next reflash.
IMHO even if u charge with a full charged battery still u get a prob so i think its a common issue with the jasjar and its power managment software itself by default as lot of people with diffrent ROMs are complaining about it.
no changes...
well, folks, i tried all these gimmicks but not to any definite changes ... i guess i need to consult the service center guys at last...i didn't want to do that but i guess i need to. i'm sure it's not my battery as i've replaced 3 of them...i dont kno what else to do!!! thanks for ur posts tho as i get to try diff things to check if ma battery is doing ok...keep postin...thanks...
josh.
how 2 discharge a battery >>>>>
problem with battery?
I have the same problem, it firs appear on original battery when charge was 40-50% so I have bought the same battery model (1620mAh). But it doesn't help. Now I,m using the 3200mAh battery and it doesn't help as well. The thing is that XDA switch off it self always on deferent charge level (sometimes is on 20%, 45% ar 80%...so is very difficult predict when it happen again). And one more thing...when it switch-off and I try to switch-on back, I can't (keep switching off), only slolution is put on charger!!!
I have downloaded the service manual (I think called "confidential") and it mentioned that it could be a problem with main board (so its HW problem). So can anybody tell me is a problem with bat or MB? (replacing the MB is fcjfdj$#ing expansive). Thanx.
well if your XDA does not switch on until you start charging it that's a clear indication that your battery is empty. I have the same with my faulty battery. Replaced it by a working one and it's fixed. Something is definately messed up with the charging circuit or the batteries though. They are not supposed to die so easily.
SpyderTracks said:
It's worth taking into consideration that when flashing, you really need to have a full battery. There are reports of batteries starting this kind of behaviour after user has flashed with drained battery, then causes battery charge issues until next reflash.
Click to expand...
Click to collapse
The first time I flashed the PDA I ruined my battery. This time I thought I'd be smart and I put in the old battery while flashing. After flashing I put back the new battery and now that one is broken too! It wasn't even in the PDA when I flashed it. How bizarre is that?
I have to admit I did not fully charge that new battery before flashing, but I figured it would be safe since it wasn;t in while flashing. The battery worked fine the day before I flashed my phone (got the "charge now or save your work" message), but after the flashing and putting it in, it just crashes at around 30% or 40%. The usual battery misery.
Maybe I should try fully charging it and then flashing again. Trouble would be how to get it fully charged though. I always felt charging cuts off early on the "broken" batteries (pull the charge plug and stick it back and it charges for a while again).
I managed to restore my battery to good health by completely discharging it in bootloader mode.
First I completely charged it. When the led went green I pulled the shcarge cable and connected it back again. After doing this a few times it doesn't stay orange so long and then I stopped and left the cable disconnected.
I reset the phone (on full battery) and then I set the unit to boatloader and waited for it to completely discharge. I reset the phone again (on empty battery) and low and behold my trusty "charge now or lose data" warning came back.
BTW I reset the PDA hoping maybe it would store the power levels. I remember that trick from my Palm days where sometimes you had to reset a PDA on full battery to calibrate it.
I charged it back to full capacity and started using the phone as normal. When the battery was empty I got no crash but a friendly warning telling me my battery was going low. Phew.
Will try the same with my other troubled battery over the weekend.
I have the same Issue.But , I think it's about Rom.
and I'm try a lot of ROM version ,only one Version canbe use more than 3 day.
I can't find any reason ,.
discharge in bootloader ,I do it ,But battiery is same time for used.
Hi all:
i know i have been braging lately a lot on the forums about the battery issue after upgrade to wm6.
BUT- after actually surfing the net for like 2 weeks non stop, i found on several sites a solution which i think would end this "IF" someone has it.
Theoritical Explanation:
it's said that when upgrading to wm6 the battery has to be atleast 50% charged "this is wrong" .
battery has to be 100% charged because for example:
if your battery is say 60% and you upgraded to wm6, the new ROM will mark the 60% as your 100% battery hence why it drains so fast.
that's why you need to charge to 100% first before upgrade BUT the only way to make sure the battery is really at 100% is to remove it and charge it in the cradle separetly until the lid on cradle changes from amber to green.
after that put the battery in your BA and start the RE-upgrade if you are on wm6 already or Upgrade if you are on wm5 or wm2003SE.
you should notice the difference, i'm currently testing it for the 2nd time, to make sure it is the right solution.
P.S. am only a noob so excuse me for the unorganised post.
Pls someone test this aswell
Regards
The battery charge level has nothing to do with the OS, its part dependent.
If i get you right, what are you saying is "if the battery level is 60% on flashing, the new OS will take 60% as being the 100%(maximum) level of what the battery can go".
I think that's wrong.
DANDANA said:
The battery charge level has nothing to do with the OS, its part dependent.
If i get you right, what are you saying is "if the battery level is 60% on flashing, the new OS will take 60% as being the 100%(maximum) level of what the battery can go".
I think that's wrong.
Click to expand...
Click to collapse
yes, hence why the battery and BA gets to warm or hot while charging as it cannot exceed the 60% mark which is marked as 100%.
i think it's the only logical explanation
Any battery get warm or hot on charge (or one some type of charge, like car charge).
I may say b*** s***, but after upgrading to WM6, my battery is acting as in WM2003; some software (like HTC home) is draining more, but nothing isn't abnormal; i still get with a 2400 mA a normal day of BA use (PDA+phone).
DANDANA said:
Any battery get warm or hot on charge (or one some type of charge, like car charge).
I may say b*** s***, but after upgrading to WM6, my battery is acting as in WM2003; some software (like HTC home) is draining more, but nothing isn't abnormal; i still get with a 2400 mA a normal day of BA use (PDA+phone).
Click to expand...
Click to collapse
the ting is my battery was working very good before upgrade with wm5 and wm2003SE but after wm6 this happened, andnever had i get the battery and BA so very hot like ths.
i finished the re-upgrade after charging battery and it's draining is much better, dropped in 1.30 hours 50% but still getting much draining, it used to drain to zero in 1 hour
ahassouna said:
the ting is my battery was working very good before upgrade with wm5 and wm2003SE but after wm6 this happened, andnever had i get the battery and BA so very hot like ths.
i finished the re-upgrade after charging battery and it's draining is much better, dropped in 1.30 hours 50% but still getting much draining, it used to drain to zero in 1 hour
Click to expand...
Click to collapse
Did you disables infrared on the new install? This might take some extra power.
nothing wrong with the OS , i believe it's a psycho matter maybe ??? my battery was 94% charged .. i took the device and went on a trip .. 4 hours with TCMP on listening to Mp3s .. i went back home after 5 hours it was 53%. Sounds good for me. 1450mAh and i charge it every 2 days with normal consumption. Maybe ur batteries are getting old because with No plugins installed it's just as good as WM2003SE.
Battery status - Its possible
ahassouna might be onto something. Logically I know this sounds unlikely. However I recall exactly the same point occuring in the smartphone forums when an OS upgrade came about. It was common knowledge that for the HTC smartphone you should have you battery fully charged when doing it. It was widely tested in the forums - www.modaco.com and generally accepted back then that for best perfromance your battery should be 100% when upgrading. BTW - in my opinion this is the best ROM ever released for BA - big thanks and respect to Helmi!
if it's so you never come back after upgrading with non fully charged battery.
I think that's wrong.
Emm let's say u were right, so i assume that the OS wont determine the correct battery level. So logically, when u get a 0% , the battery is shown as empty while it is not. So if u think a bit , when the OS indicates that the battery is empty, it shouldnt turn itself off because in fact IT IS NOT. So if you get ur device to turn itself off without being able to power on again , that means that the OS was right and it was 0% for real. ( Correct me if i'm wrong )
as the Matter of fact, wm6 is slightly 'heavier' than wm2003, it contains more drivers and stuffs. so it will consume lot More resource than wm2003. I think battery draining also closely related to the read/writing speed of your sdcard, how big the capacity...
My SX66 drains equally under all three OS's, Though I must admit I quickly upgraded from WM2003SE to WM2005. Ran WM2005 for almost a full year, good battery drain, WM2006 seems to drain the same thus far
I would have a look at your battery, there cheap to replace on ebay and such.
Slide2Unlock
Do you use Slide2Unlock? I confirmed that the software was draining battery faster especially ver 1.216. I uninstalled it and my battery back to normal.
I hope it helps.
I don't believe that would cause any problems...the OS is independent of the battery. Anyway, my battery use is only slightly higher in WM6 than WM5.
Your battery can be at any level when you upgrade the ROM...I really cannot see how the OS would "read" the status of the battery and set that as the 100% level.
Try running your battery down to something below 50%, then reflash your ROM...now what does the battery meter show? I bet it shows the same as before you flashed it, below 50%.
blues01 said:
Do you use Slide2Unlock? I confirmed that the software was draining battery faster especially ver 1.216. I uninstalled it and my battery back to normal.
I hope it helps.
Click to expand...
Click to collapse
i double that
the_scotsman said:
I don't believe that would cause any problems...the OS is independent of the battery. Anyway, my battery use is only slightly higher in WM6 than WM5.
Your battery can be at any level when you upgrade the ROM...I really cannot see how the OS would "read" the status of the battery and set that as the 100% level.
Try running your battery down to something below 50%, then reflash your ROM...now what does the battery meter show? I bet it shows the same as before you flashed it, below 50%.
Click to expand...
Click to collapse
Yes. In fact every battery has a internal chip for charge controll and status level. OS reads the status of the battery by this chip.
blues01 said:
Do you use Slide2Unlock? I confirmed that the software was draining battery faster especially ver 1.216. I uninstalled it and my battery back to normal.
I hope it helps.
Click to expand...
Click to collapse
no i don't use it, i finished flashing for the 3rd time with a "3rd battery" Still same problem BUT draiing is less than before but still 1-2 hours max without any calls and drops to zero.
am begining to think my BA went razy for some reason.
P.S. i have no apps or anything installed other than flashing the ROM.
My BA drains normally. I have 2-4 days of standby with occasional calls and usage. The backlight auto-closes in 30 seconds, the power goes off in 1 minute.
ahassouna said:
no i don't use it, i finished flashing for the 3rd time with a "3rd battery" Still same problem BUT draiing is less than before but still 1-2 hours max without any calls and drops to zero.
am begining to think my BA went razy for some reason.
P.S. i have no apps or anything installed other than flashing the ROM.
Click to expand...
Click to collapse
Can u retest it on a WM2003SE ? i think maybe a short circuit with ur device or whatsoever
ramdacBlueAngel said:
Yes. In fact every battery has a internal chip for charge controll and status level. OS reads the status of the battery by this chip.
Click to expand...
Click to collapse
Exactly...so the first post is wrong...the OS reads the status of the battery and it doesn't matter what charge status the battery is at when you reflash...the battery status circuit will show the proper charge percentage...
Last night before I was going to bed I have had my xperia fully charged.
When I woke up this morning the battery was almost empty.
I can't understand how that happened :S I had no programs running except maybe g-alarm.
Anyone who has an idea what could've drained my battery?
No reception or low signal from ur fone provider maybe? it consumes a lot of power getting the signal. Or your wifi is turn on.
Happened to me several times.
But I'm not sure I didn't let something run in the background. Mediaplayer for example .. skype can eat battery in minutes too.
Also I don't know what battery level I had at the evening. It was above 50%, but then with Xperia, the indicated level does not correspond to remaining time well. It drops fast after 50%.
I would love if I could close any application with red phone button. Anybody knows about software which can do it ?
Dr.Sid said:
Happened to me several times.
But I'm not sure I didn't let something run in the background. Mediaplayer for example .. skype can eat battery in minutes too.
Also I don't know what battery level I had at the evening. It was above 50%, but then with Xperia, the indicated level does not correspond to remaining time well. It drops fast after 50%.
I would love if I could close any application with red phone button. Anybody knows about software which can do it ?
Click to expand...
Click to collapse
are you using fish panel?fish panel caused battery drain in my experience.also bluetooth and wifi as well.
do you use AEButton plus or S2U2 (more to the point AEButton here) as AEButton especially seems to have drainage issues if its 2.6.5, at least it seemed to for me and some others...
human75 said:
are you using fish panel?fish panel caused battery drain in my experience.also bluetooth and wifi as well.
Click to expand...
Click to collapse
None of these. And Fish panel for example cannot be left running in the background (AFAIK). Media player, or skype easily, since they are even intended to be run in background.
Happens mee also sometimes. Weekend I noticed that after useing opera it does it. I chargered my xperia in friday, didnt use it then whole day, or in saturday, but in saturday night I wanted to check news whit opera, battery was 90% when I start, after use its was 80%. I go to sleep and morning I waked up to that xperia says battery critical. It cant be anything else when I didint use nothing else whole day, and when it was allredy stand one day whit only 10% loss, and now randomly use 60% battery at night.
I think I had S2U2 running in the background, could that be it?
I'll soft reboot before going to bed tonight and see what happens ^^
use fdcsoft task manager, it'll tell you what's running
battery won't run down on its own, it needs something to cause it.
as said lowsignal will do itn
do you really need to leave the x1 on overnight?
if you turn it off it'll be all nice and alert after a nice sleep
only time my x1 runs low is if I fall asleep reading something with mobipocket on autoscroll...
I found that when I was running Push E-Mail over iMAP, I had this battery draining issue. Make sure you're configuring FlexMail or any other IMAP IDLE client to only the essential folders that you want to keep 'live', as each IMAP IDLE folder requires its own connection and can eat up a lot of resources/battery.
I've actually wrote myself a MortScript that will monitor the battery status and allow FlexMail to stay open if the battery is over 80%, and it will close FlexMail if the battery falls below 80%.
Still hating the fact that we only get battery readouts in 10% increments. Total crap for a high profile device...
I don't need to know what is running. I want to be sure I've just closed something. In fact I need to close 99% of application, I only need IM+ in background and that only sometimes. Also sometimes I need to adjust some settings without closing current application. But otherwise I always want to close, not minimize, and I want to do it with a key.
Same issue here , will a lil bit more tricky , i had my phone TURNED OFF , and was CHARGING , woke up and the red little light on the power button ( light of death) was on, replaced my batter with my spare one , and the phone came back to life , yet it isn't charging ( the charging icon is there but still not charging) , I'm using the wall charger ( if any one is thinking of an usb issue) . So for now i'm useing an "external battery base charger" which sucks to be honest ( takeing the battery in and out isn't the best thing ever ) ..
The funny part is that SOMETIMES ( 1 out of 100 ) the phone charges, why !! i don't really know . I reflashed my device , hardreset and done anything someone can possibly do yet no solution , it's not on warranty and to be honest i think that it's more of a software issue (i know that not charging while switched off is against this ) , I'll be so greatful if any of you guys have any ideas
I had the same problem, but for me it happend when I got a text message at night the the screen wouldn't turn off but xperia tweak fixed that
I had one instance of mysterious night-time draining. It actually woke me up at 4am with the low battery alarm.
The only thing I think might have caused it is that I had it sitting next to my old Nokia, which was switched off. I figure its antenna must have been interacting with the X1's such that it had to go to full power just to keep the cell signal.
Hello all,
I don't have this issue now but i've noticed something weird last night.
All background applications was turned off, screen backlight was turned off, LEDs on both sides was turned off... But there was white light inside my phone. I was sleepy so i didn't check keyboard backlight. Propably it was it. It was visible only it dark, in correct angle.
I've turned device off and on again and there was no light any more.
I had tried this issue before, it fixed after I uninstall the SKtools
I uninstalled S2U2 and I think it made the job
Li-ion or Li-poly?
i've been searching forums here and there regarding x1's battery issue and i'm not using any of those suspected programs (AEplus, S2U2, batti, etc.). mine is just stock xperia as of now, except for SPB plus. but still my battery only manages 14 hours of juice with very minimal usage i assure you. i have tried charging while off, hard reset, upgrade to R2A UK generic ROM, but still my battery sucks. i also noticed on the Settings>Power box that my "Main battery" is Li-ion, isn't it supposed to be Li-poly as the one written on the battery itself (BST-41)? Also, how much drain do we expect from a weak carrier signal? thanks guys.
FrezoreR said:
I uninstalled S2U2 and I think it made the job
Click to expand...
Click to collapse
I also had a problem with the battery not lasting me through the night. I eventually found out it was S2U2. I upgraded to v1.45 (with the power-saving option) and now the battery remains at the same level during the night.
FrezoreR said:
I can't understand how that happened :S I had no programs running except maybe g-alarm.
Click to expand...
Click to collapse
You said it yourself.
I've been experiencing this for many days. I would charge my unit overnight only to be awaken by the low battery signal. In a normal scenario my X1 would only loose only 0-10% over a period of 8 hours in standby. When the fast discharge occurred it would drop to 50-60% and the unit was warm in touch.
I checked repeatedly to find which program was to blame, soft reset the device various times and changed my usage patterns to rule out programs that didn't had to do with it.
In the end I discovered that every time G-Alarm was triggered or set up an Alarm the quick discharge effect and warm device appeared.
I got rid of it and haven't encountered the problem again.
The scenario is this. I charge it every night. The orange light does work and it will show 100% in the morning. It will then shut down at random times and when restarted say the battery is low. I can plug it in again and reset it and it will show from 0 to 100%. Once I take it off the charger it may run all day and deplete the battery or it may die suddenly and tell me it's got a low battery again.
Should I consider the phone dead or does it sound like a faulty battery. It is the original battery and is 2 years old.
Marksm,
I think could be caused by:
1st: some hidden app wich consume a lot of energy that is placed on your phone or
2nd: a phone virus made to produce that behavior or
3rd:a battery control software issue.
For that, I'd advise you to:
1st: verify the programs and process that are running on your phone, seacrh for unknow ones and see on the internet what they do so you can remove the unwanted ones;
2nd: install one or more of the mobile antiviruses (one at each time) that are avaliabe on the internet and perform a full verification of your PDA;
3st: put a new ROM on the Blackstone; but first read how to do it well, if you don't know how, and be sure to be aware about all issues and risks that this action may bring.
Wishing you a good luck!
Stay in peace!
marksm said:
The scenario is this. I charge it every night. The orange light does work and it will show 100% in the morning. It will then shut down at random times and when restarted say the battery is low. I can plug it in again and reset it and it will show from 0 to 100%. Once I take it off the charger it may run all day and deplete the battery or it may die suddenly and tell me it's got a low battery again.
Should I consider the phone dead or does it sound like a faulty battery. It is the original battery and is 2 years old.
Click to expand...
Click to collapse
I have exactly the same problem. I restored the original ROM and SPL and nothing has changed.have you tried another battery? Is like the battery controller is broke. The phone is under warranty but the battery is not covered, so I would know if send it to HTC or to buy a new battery!
Similar issues reported in a post above. A new battery seems to have fixed it but needs more time to tell. I will probably order a new battery too.
http://forum.xda-developers.com/showthread.php?t=821701
me 2 going through the same problem.....really wanna get out ov it..
[TL;DR]
Phone battery suddenly drains faster than usual, drains to 0% overnight. Problem still persist even after April update and after battery change. Can't find any solutions. Help me.
Hey, so about a week ago something very strange happened to my Mi A1 and got worse overtime. So what happened was my battery went from 80+% to 0% overnight. I woke up confused and just recharged it and didn't think too much. After a full charge, I noticed the battery drains abit more than usual and had to plug it in constantly. Before going to bed I charged my phone to 100% to see if it would drain to 0% again. It did. As time passes the problem gets worst. The phone started getting warm when charging (around 40+°C up to 50°C) then after a while the phone runs warm even when not charging (never goes below 40°C). My phone always used to run at about 30-35°C even when charging. I changed the battery myself because there was no warranty on it but it didn't fix the problem. However it did help abit. The battery drains ever so slightly slower now but still drains to 0% overnight. It still runs warm but now it does go below 40°C (rarely). Before and after the battery change, the discharging rate is about 700mA and sometimes reaches 1000+mA (used an app called Ampere, not too sure how accurate it is). The phone was also warmer than usual when charging even when the phone was off (before and after the battery change). I tried factory resetting to see if that does anything but had no luck. I also tried using a Wakelock detector app to see if there was an app excessively triggering a wakelock but all seemed normal. I even tried downloading a "battery calibration app" which obviously didn't work. So I feel like it's a hardware problem.
Now here's what I did and did not do to the phone before the problem happened. What I did was I do charge the phone quite alot most of the time. What I mean by that is when it hits about 30% I'll plug it in but I never leave it plugged in after a full charge or charge it overnight and I seldom let the battery drain to below 10%. Even so, the phone never got warm like how it is now. That's about all I did to it. Now what I didn't do was, I never tried to install custom ROMs or root/modify my phone in anyway except for the post about how to enable 4G+ which didn't work for me.. My phone is completely stock. I also didn't install any new apps from the playstore or from any 3rd party sites nor were there any updates for any apps installed in my phone. I've had the same apps installed for a couple of months before this happened. I also haven't dropped my phone for a couple of months. I only dropped it less than 5 times from short heights and I have a very rugged case on. I also didn't use any 3rd party chargers. I'm still using the charging brick and cable that came with the phone. I have tried using other chargers that are 2A but no luck. So basically I didn't do anything out of the ordinary prior to this problem.
Just some extra information
1. The hottest part of the phone is at the top right corner of the back. I assume the CPU is there (?).
2. It happened before the April update. It was the same before and after the April update.
3. Phone is running on Android Pie if that wasn't clear
4. The phone is only 10 months old
5. My phone is the Global ROM version
6. Performance wise, its still responsive and snappy. Doesn't lag or freeze or anything.
6. I always have mobile data on and use it as hotspot for my laptop at uni. I have been using it like that for the past 9 months. However the problem happened when I was at home during sem break so I was mostly connected to Wi-Fi.
Sorry for such a long post. I hope somewhere out there, there is someone who can help me or other people that have a similar problem so we can fix it.
Thanks.
In the upper right corner, should be the modem area.
Try holding the phone on airplane mode during the night and monitor drain.
Also, try changing the SIM slot and do an APN reset. If this fails too, try changing your SIM card or if u can, try another operator SIM.
If you changed any value with QXDM PRO , try and put back the default values.
Good luck