8525, sync w/ USB 5% of the time, no changes seem to change anything.
did the notification edit here on xda
uninstalled/reinstalled activesync
upgraded to 4.5
deleted partnership
uninstalled firewall
checkdisk
ran the resync program
installed office, .net 2.0, activesync 4.5 on entirely different computer
[edit: added for clarification]
tried unchecking the advanced connection box in start>settings>connections>usb to pc
[/edit]
when connecting to either computer, i get the "usb device seen" chime, but not the "i can do something with this device" jingle
get the "active sync cannot connect with this device" popup, run the diags and everything is okay. ms site politely informs me that the cause of my problem is that the device cannot connect to the pc.
anything i missed? i gave up on it 6mo ago when i got the phone bc i got bluetooth sync to work but now i want to flash to wm6
Thanks
start>settings>connections>usb to pc.
Untick the box. See if that helps?
Try this procedure step-by-step
1. make sure your phone is not connected to the computer in any way
a. Bluetooth off
b. WIFI off
c. USB cable not connected
2. Run spybot S&D (I always do this when the computer misbehaves - and make no mistake your computer is misbehaving)
3. Terminate all other running programs
4. Hook your phone to the usb cable and the usb cable to the computer. (don't worry if it syncs or not)
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
7. Disconnect the Phone
8. Open the Control Panel "Add/Remove Programs" and uninstall Active Sync
9. Reboot the computer
10. Connect to the internet and get a fresh copy of Activesync 4.5 and install it.
At this point if you can back up your PIM to the storage card or something it would be great because I suggest you do a hard reset of the phone. go to the settings page and select System. Tap the clear storage icon and follows the instructions to reet the phone.
11. Reset phone as above
12. When phone reboots, connect it to the computer via the usb cable.
Phone should sync from now on.
Good Luck
PS.
MrVanx is right, that could help but it will limit your phones capability. However if my method fails that may be your only option short of reflashing the phone with some other ROM.
I've tried MrVanx' solution also, just forgot it in the original post. It seems to sync more often when the box is ticked anyhow.
I don't have a problem with hard reseting or flashing. I'm going through this hassle for the sole reason of flashing to schaps 4.31
Ill try that when i get home tonight
Say I do a sprite backup before hard resetting the phone. After I do the hard reset, I restore the sprite backup. Will my lack of syncing problem come back? I assume it will.
After the hard reset and the initial sync on the "fresh WM5 install," I should proceed from there with the WM6 install, correct?
I have a TyTn II and experiencing a similar problem as sook..
I did all the steps except for these:
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
The thing is i cant find my mobile device anywhere in the device manager or in the network adapters subcategory. Any ideas?
mrvanx said:
start>settings>connections>usb to pc.
Untick the box. See if that helps?
Click to expand...
Click to collapse
+++ worked for me
sook said:
Say I do a sprite backup before hard resetting the phone. After I do the hard reset, I restore the sprite backup. Will my lack of syncing problem come back? I assume it will.
After the hard reset and the initial sync on the "fresh WM5 install," I should proceed from there with the WM6 install, correct?
Click to expand...
Click to collapse
Yes proceed. And no I don't think the failure to sync problem is related to the backups so that should be safe
SeqHTCTyTnII said:
I have a TyTn II and experiencing a similar problem as sook..
I did all the steps except for these:
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
The thing is i cant find my mobile device anywhere in the device manager or in the network adapters subcategory. Any ideas?
Click to expand...
Click to collapse
Not sure how a TyTN II looks to the device manager. try this instead:
open the device manager and click on the USB devices subcat.
Then connect your phone to the computer via the usb cable. pay attention and uninstall the usb device that appears when you hook up.
Then rescan. Reboot both the computer and the phone and see if that helps
sook said:
I've tried MrVanx' solution also, just forgot it in the original post. It seems to sync more often when the box is ticked anyhow.
I don't have a problem with hard reseting or flashing. I'm going through this hassle for the sole reason of flashing to schaps 4.31
Ill try that when i get home tonight
Click to expand...
Click to collapse
Before you try flashing make sure you have the Hard-SPL V7 bootloader installed.
You can flash without activesync tho.... activate the bootloader and connect your usb cable. If the tricolor screen indicates a usb connection then you can run the RUU wrapper, follow the usual steps and it should flash just fine.
You activate the bootloader by pressing and holding the "Power" and "OK" buttons and depressing the reset with your stylus (the OK button you use has to be the one next to the jog wheel)
I can't find my Hermes in device manager either. I'll try doing the flash through the bootloader i guess.
Did you try un-checking the "Enable Advanced Network Functionality" box as mentioned in Reply #1? That fixed it with mine. It would sync with my WinXP work PC, but not my WinXP Home pc, unchecking that box fixed it. Been fine ever since....
cyberscribe said:
You can flash without activesync tho.... activate the bootloader and connect your usb cable. If the tricolor screen indicates a usb connection then you can run the RUU wrapper, follow the usual steps and it should flash just fine.
Click to expand...
Click to collapse
do i have this correct?
1. enter bootloader
2. connect usb cable, check for confirmed connection
3. use ruuwrapper.exe to install hardspl http://www.mrvanx.org/cms/index.php...ask=view&id=52&Itemid=26&limit=1&limitstart=2
4. return to bootloader
5. connect usb cable, check for confirmed connection
6. use ROMupgrade.exe to install new radio http://www.mrvanx.org/cms/index.php...ask=view&id=52&Itemid=26&limit=1&limitstart=3
7. return to bootloader
8. connect usb cable, check for confirmed connection
9. use ROMupgrade.exe to install Schaps 4.31 http://www.mrvanx.org/cms/index.php...ask=view&id=52&Itemid=26&limit=1&limitstart=4
10. reboot ppc, delete partnership from pc activesync, cross fingers, sacrifice a goat, sync, install programs, bask?
JETninja said:
Did you try un-checking the "Enable Advanced Network Functionality" box as mentioned in Reply #1? That fixed it with mine. It would sync with my WinXP work PC, but not my WinXP Home pc, unchecking that box fixed it. Been fine ever since....
Click to expand...
Click to collapse
yup. tried it on the laptop that i use constantly with a legit copy of XP Pro. tried on BRAND NEW install of newest hacked version of XP Pro. neither were successful.
AT&T 8525 USN Syncing problem ...
I had the same problem too ... fortunately I had a simple fix.
I made sure that I only use the USB/mini-USB cable that came with my AT&T 8525. If I use a USB that came from a different device (like another phone or camera), it doesn't want to sync, except once in a blue moon.
The other USB cables may charge it, but won't sync it.
I've read elsewhere in this site that our 8525's can be picky with their pinouts on the USB, so this might be the issue. I hope it's something this simple for you!
Hope this helps!
it's a thought. ill dig through my drawer of cables and pull out all the usb/mini usb cables. no idea if I'm using the original or not.
however 6 mo ago when i gave up on the thing the first time i know it was the correct cable
sook said:
it's a thought. ill dig through my drawer of cables and pull out all the usb/mini usb cables. no idea if I'm using the original or not.
however 6 mo ago when i gave up on the thing the first time i know it was the correct cable
Click to expand...
Click to collapse
sometimes cables go flakey, but the cable we use is standard not proprietary so any A - miniusb cable should work.
Anyway the procedure you outlined above should have worked, am I to understand you still have the ATT ROM? If so talk to them about this problem.
If not access the bootloader again and hook up your usb cable. Does USB appear at the bottom of the screen?
Are you using the usb adapter that came with the phone? If not try to go back to that. The pinouts are the same as a miniusb but the form factor makes for a better fit and regular miniusb jacks can cause nonsyncs.
If you aren't getting "USB" at the bottom of the screen it is either a bad cable, a bad usb port (either at the comp or your phone), bad usb drivers, or just bad hardware in the phone. If any of these is the problem, all you can do is talk to AT&T hopefully before the warranty expires.
Sorry I wasn't more help mate.
The cable I've been using is the one that came with the phone. I tried the cable that came with my mp3 player and got the same results.
I do still have the out-of-the-box ATT Rom, however, the steps you outlined did not fix my problem. I did notice that my device appears as "HTC USB Sync" which I found strange. Is this normal?
USB does appear when I connect the phone in bootloader to the computer. I've tried two USB ports on two separate computers. Both computers are completely up to date with MS and drivers.
I suppose I'll go bother the people at ATT.
If I'm done with the ATT Rom, can I do all the flashing through the USB connection to the bootloader?
hey guys im having the same problem (TyTN II) it'll charge, but wont sync or show in device manager (i am using the original cable though)
i've tried to go into bootloader, but it doesnt say 'usb' at the bottom like it should, instead it says 'serial' i've tried diff usb ports, i've also unticked the advanced network box, softreseted, and hardreseted still no go...any ideas?? (im using alex's wm6.1 rom, could wm6.1 possibly have something to do with it?)
ActiveSync BOOSTER
Is there a way to boost up speed of Sync
Is there a any software or Cab file for it ?
Also want to know after we sync Phone
It keeps repeating to sync, is there a way to stop it ?
With removing the phone
Please Help
I just purchased a Telstra Touch HD T8285 on eBay. Unfortunately, the seller did not disclose that he had flashed a new ROM (Dutty ROM) to it and that USB syncing and wifi do not work. I'd like to try and get this fixed on my own...otherwise I will have to try and get the seller to take the phone back and refund my money. I really like the phone so I just want it to work properly.
After much searching on here I discovered that I could flash directly from the flash card, thus bypassing the problem of USB syncing not working. I have tried a few ROMs (EnergyRom, Miri, Telstra updated direct from HTC) and neither wifi nor USB syncing works with any of them.
I have tried all the hints/suggestions about changing USB settings in activesync on both the phone and computer and nothing works. I cannot even get my computer to recognize the phone as a USB storage device (the phone just starts charging but activesync acts as though it's not even connected). When I go into bootloader mode on the phone it displays "serial" but never changes to USB.
Bootloader screen displays the following:
BLAC120 32M
SPL-1.56.Olinex
MicroP-Blackstone (LED) v6
From what I've read on here, I think I need to get a new version of SPL on my phone but I don't know how to do so without being able to use USB syncing. Is there any way to reflash SPL on my phone using the card flash method?
Someone please help!
gmischenko said:
I just purchased a Telstra Touch HD T8285 on eBay. Unfortunately, the seller did not disclose that he had flashed a new ROM (Dutty ROM) to it and that USB syncing and wifi do not work. I'd like to try and get this fixed on my own...otherwise I will have to try and get the seller to take the phone back and refund my money. I really like the phone so I just want it to work properly.
After much searching on here I discovered that I could flash directly from the flash card, thus bypassing the problem of USB syncing not working. I have tried a few ROMs (EnergyRom, Miri, Telstra updated direct from HTC) and neither wifi nor USB syncing works with any of them.
I have tried all the hints/suggestions about changing USB settings in activesync on both the phone and computer and nothing works. I cannot even get my computer to recognize the phone as a USB storage device (the phone just starts charging but activesync acts as though it's not even connected). When I go into bootloader mode on the phone it displays "serial" but never changes to USB.
Bootloader screen displays the following:
BLAC120 32M
SPL-1.56.Olinex
MicroP-Blackstone (LED) v6
From what I've read on here, I think I need to get a new version of SPL on my phone but I don't know how to do so without being able to use USB syncing. Is there any way to reflash SPL on my phone using the card flash method?
Someone please help!
Click to expand...
Click to collapse
It sounds more like you need to update your usb drivers by following this guide. Also ensure that you have enabled 'allow usb connections' in activesync connection settings.
Unfortunately you cannot change SPL without using your usb, so let me know if this works
unfortunately that guide to updating USB drivers does not work. When my phone is in bootloader mode the bottom only says "Serial". It never changes to "USB" so the computer does not even recognize that a device is connected.
gmischenko said:
unfortunately that guide to updating USB drivers does not work. When my phone is in bootloader mode the bottom only says "Serial". It never changes to "USB" so the computer does not even recognize that a device is connected.
Click to expand...
Click to collapse
Did you check that 'allow usb connections' was turn on in activesync connections settings?
Also when you update usb drivers you need to turn your pc off then on again.
Yes I made sure of that setting in ActiveSync.
Since my computer does not recognize my phone being connected, the "Windows CE USB Devices" is not listed in the Windows Device Manger. I have tried connecting my phone to 3 different computers (Windows XP and Windows 7) using different USB cables and still get nothing.
The closest I got was one time yesterday when I plugged my phone into the a/c adapter to charge, the USB window popped up on my phone asking whether I wanted to connect to ActiveSync, Storage Card, or Internet Sharing. That is the only time the window has ever opened and it wasn't even plugged into a computer.
gmischenko said:
Yes I made sure of that setting in ActiveSync.
Since my computer does not recognize my phone being connected, the "Windows CE USB Devices" is not listed in the Windows Device Manger. I have tried connecting my phone to 3 different computers (Windows XP and Windows 7) using different USB cables and still get nothing.
The closest I got was one time yesterday when I plugged my phone into the a/c adapter to charge, the USB window popped up on my phone asking whether I wanted to connect to ActiveSync, Storage Card, or Internet Sharing. That is the only time the window has ever opened and it wasn't even plugged into a computer.
Click to expand...
Click to collapse
ok, try going to to Start > Settings > Connections > USB to PC and ensure that 'ActiveSync' is selcted along with 'Enable faster data synchronization' and try again
Fallen Spartan said:
ok, try going to to Start > Settings > Connections > USB to PC and ensure that 'ActiveSync' is selcted along with 'Enable faster data synchronization' and try again
Click to expand...
Click to collapse
I've tried that as well.
Basically, if it's been written here on the forum I've tried it. Each thread I've found where someone has had the same problem seemed to fade off and no one reported back (even those that fixed it).
Possibly a hardware problem with your usb port then which would require a warranty return unless anyone else has any suggestions
EDIT
Try flashing original stock rom, i.e. the one which was on the device originally when bought. This rom will still flash even if bootloader says 'serial'. This is the only rom that this works for. Unfortunately in your case you do not know what this rom was so a bit of guess work will be required going by date and location. Stock roms are available in wiki here and it'll just be trial and error
Hi
Hello,
Unfortunately,I have the same problem With my HTC HD phone, I've tried every thing but i couldn't found a solution to my problem, in SPL stage the screen show me only Serial and hang on it ,and when i connect my phone to my PC not change to USB,
So please any one have a clue for this,
Thanks in advance.
Dear gmischenko,
Did you solve your problem??
Hi I'm getting the USB Not Recognized / Malfunctioned error messages in Win7 Ultimate. My phone used to connect to my PC flawlessly.
I'm using the stock USB cable that came with the phone, I've tried for weeks now to get it to sync. I've tried uninstalling, reinstalling WMDC, edited the permissions for some registry key related to it, I've even tried syncing with bluetooth. It will not work on any Win7 PC (I haven't got the opportunity to try any other OS's). Also it's not just the syncing issues, it wont even show up as a storage device in Windows Explorer.
I've exhausted all options, I've tried 2 usb cables (one from a car charger and the original one), I've tried changing connection mode from Activesync (enhanced on and off), Disk Drive and even Internet Sharing.
The only way the USB has worked is in bootloader was today during bootloader and in magldr 1.12 (USB Flasher and USB Mass Storage), at first I flashed a newer Energy GTX ROM and then WP7.
Zune does not detect the phone nor does Phone Developer Tools.
Please help, I need to get it working again!!
Thankyou.
I can't connect it to PC . I mean , i conncect the usb cable to my phone and my pc ... my phone shows that it is connected to my pc ... but there is nothing happening . I mean the PC doesn;t find the my phone. What should i do. Ty everybody! Sorry for my english
Well,may i know on what OS are you trying to establish USB connection? WM/Android?...For WM, have you installed windows mobile device center on your PC and tried syncing? As for android,try installing the right version of HTC Sync on your PC. Also, ensure you tick 'USB Debugging' under Settings-Applications-Development. For a few android builds, there will be a notification, prompting you to turn on USB Storage after you connect the USB cable. You have to try all those first before moving on to advanced troubleshooting like manual driver installation,android sdk,hard rest,etc.
hi there,
thanks for the great omniROM, i use it a while now and I was never so happy with my Galaxy Note N7000!
running the latest 4.4.2 (20140329) and have a SDcard in slot working properly.
I upgraded from stock 4.1.2 and it was an better experience than ever before, but there is just one thing that bothers me: USB Connection
when I connect an USBStick via OTG or via USBcable to PC, the only thing that happens is charging. this appeared some while ago still in StockROM after excessive use of USBSticks (all FAT) and keyboards. I was hoping the rooting and upgrading to OmniRom would 'reset' this behaviour, but it didn't tried differend tools, some with SU and nothing worked.
so my questions is: how can I get into the PhoneUtil-menu in omnirom or the UART/USB option?
after researching some more, I found this similar case and (possible?) solution. i'm keeping some hopes in this to get USBtransfer working with USBsticks again:
........ GT-7000 USB Data connection not working
My phone was not detected as MTP by the computer.
My phone didn't detect that it was attached to a PC.
On my PC --It didn't work.
Another PC --It didn't work.
Even another PC --It didn't work.
Mac --It didn't work.
Tried all sorts of things written on many websites. --It didn't work.
There was no MTP option in the status bar. It just always charged using the PC.
THEN... Finally 1 day, when I was looking at the back of my CPU (PC ) I saw my USB 3.0 Ports (the Blue ones). I had never connected anything to them. So,
Tried on a USB 3.0 Port --It WORKED!
My phone was immediately detected as MTP. The option showed up in the status bar. I could transfer files. But then- What about my USB 2.0 Ports?
Then I did the following :
Dialed *#7248# for the PhoneUtil options.
Under 'UART' tap MODEM. Under USB, PDA.
If this is already your setting, choose the another ones (PDA for UART and MODEM for USB) and then tap SAVE and RESET.
Again dial *#7248# for the PhoneUtil options.
Under 'UART' tap MODEM. Under USB, PDA. Finally tap SAVE and RESET.
Your phone will now be detected as MTP with all types of USB Ports now.
thanks and best regards